Search NASA⌕ Search

SEARCH · Search NASA

Results for “elastoplasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Large rotations of the grain-scale stress tensor during yielding set the stage for failure

The stress-state within individual grains in a polycrystal determine the fate of the aggregate including mechanical failure. By tracking the evolution of the stress tensor throughout the elastoplastic transition, large rotations of the stress-state, which have long been theorized to occur, are observed experimentally for the first time. These stress rotations (~15°) are more than an order of magnitude larger than the concomitant crystallographic lattice reorientations (~0.9°) well-known to occur during metal plasticity. Furthermore, these rotations are accompanied by a decrease in stress triaxiality within certain grains, promote strain softening, and set the stage for failure at an early stage of deformation. Finally, these results provide a completely new perspective through which to contemplate the question of “hot-spots” responsible for failure of high-performance structural materials.

36 MATERIALS SCIENCE↗

A new coupled multiphase flow–finite strain deformation–fault slip framework for induced seismicity

Production of hydrocarbons and water from subsurface reservoirs are known to cause permanent deformation of the reservoir and seismicity along faults both of which are detrimental to sustainable development of natural resources. Most of the prior studies on understanding fluid flow-induced plasticity and seismicity have focused on one or the other phenomenon due to the numerical difficulty associated with simultaneous modeling of the two failure phenomena because stress and deformation evolve non-linearly in both plasticity and seismicity. However, in reservoirs undergoing long-term production, plastic failure can alter the stress paths of points on a fault such that the onset, location, and magnitude of actual seismic events can no longer be predicted by a poroelastic simulation due to inaccurate stress and deformation history. We present a computational framework for coupled multiphase flow, finite strain poroplastic deformation, and dynamic fault slip and use it to understand the impact of plastic deformation on the onset, location, and magnitude of induced fault slip events. We evaluate the impact of plasticity on reservoir pressure, deformation, induced stress, and fault slip by comparing infinitesimal strain elastic and finite strain poro-elastoplastic models. For real-world applications, we consider different scenarios where the reservoir is either mechanically weaker or stronger than the caprock. We analyze the stress evolution as a function of the change in reservoir pressure to understand the role of contrast in reservoir and caprock elastic moduli on geomechanical stability. The results show that the poroplastic reservoir exhibits larger vertical deformation and delayed slip than the poroelastic reservoir after the same amount of oil production. For the same amount of pressure drop, a reservoir with a smaller modulus than the caprock displays a larger vertical displacement and an earlier onset of both plastic failure and fault slip. For a reservoir with a larger modulus than the caprock, vertical displacement is larger on the reservoir top boundary and smaller on the ground surface, and a higher pressure drop is needed to induce plastic failure and fault slip.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Efficient rolling texture predictions and texture-sensitive properties of α-uranium foils

Here, finite element (FE) analysis was used to simulate the strain history of an α-uranium foil during cold-rolling, with the sheet modeled as an isotropic elastoplastic continuum. The resulting strain history was then used as input for a viscoplastic self-consistent (VPSC) polycrystal plasticity model to simulate crystallographic texture evolution. Mid-plane textures predicted via the combined FE→VPSC approach show alignment of the (010) poles along the rolling direction (RD), and the (001) poles along the normal direction (ND) with a symmetric splitting along RD. The surface texture is similar to that of the mid-plane, but with a shear-induced asymmetry that favors one of the RD split features of the (001) pole figure. Both the mid-plane and surface textures predicted by the FE→VPSC approach agree with published experimental results for cold-rolled α-uranium plates, as well as predictions made by a more computationally intensive full-field crystal plasticity based finite element model. α-uranium foils produced by cold-rolling must typically undergo a final recrystallization anneal to restore ductility prior to their final application, resulting in significant texture evolution from the cold-rolled plate deformation texture. Using the texture measured from a foil in the final recrystallized state, coefficients of the thermal expansion and elastic stiffness tensors were calculated using a thermo-elastic self-consistent model, and the anisotropic yield loci and flow curves along the RD, TD, and ND were predicted using the VPSC code.

36 MATERIALS SCIENCE↗

A continuum meshfree method for sandbox-style numerical modeling of accretionary and doubly vergent wedges

Here, in this study, we introduce and utilize GEOSPH, a Lagrangian particle-based continuum Smoothed Particle Hydrodynamics (SPH) code to simulate the deformation of geologic materials in sandbox-style experiments using an elastoplastic constitutive model. Due to the meshfree nature of SPH, our proposed framework is capable of handling the large deformations characteristic of sandbox-style experiments. SPH is also able to capture strain localization and discontinuities, allowing us to resolve faulting patterns emerging in the sandbox experiments. We successfully validate our SPH implementation against the benchmark experiments of Buiter and co-workers, and then apply SPH to understand the deformational processes occurring in doubly vergent orogens resultant from the S-point experimental setup and from finitely high wedge-like indenter backstops of different inclinations. We find that the topographic slope of the prowedge results from the competing processes of vertical uplift due to the indenter and forward thrusting, while the topographic slope of the retrowedge is a product of repeated shallow slope failure. Our findings show that SPH is a promising numerical method which should be added to the current palette of computational tools used by structural geologists for solving problems relating to tectonics and crustal deformation.

58 GEOSCIENCES↗

Evolution of microstructure and residual stress during annealing of austenitic and ferritic steels

In this work the recovery and recrystallization processes occurring in ferritic and austenitic steels were studied. To determine the evolution of residual stresses during material annealing the nonlinear sin{sup 2}ψ diffraction method was used and an important relaxation of the macrostresses as well as the microstresses was found in the cold rolled samples subjected to heat treatment. Such relaxation occurs at the beginning of recovery, when any changes of microstructure cannot be detected using other experimental techniques. Stress evolution in the annealed steel samples was correlated with the progress of recovery process, which significantly depends on the value of stacking fault energy. - Highlights: • X-ray diffraction was used to determine the first order and second order stresses. • Diffraction data were analyzed using scale transition elastoplastic models model. • Stress relaxation in annealed ferritic and austenitic steels was correlated with evolution of microstructure. • Influence of stacking fault energy on thermally induced processes was discussed.

36 MATERIALS SCIENCE↗

Sparse modeling of space- and time-varying diffraction response of a progressively loaded aluminum alloy

Highlights: • Plasticity induces crystal orientation and lattice spacing heterogeneity. • High energy x-ray diffraction spot broadening typically accompanies plasticity. • Method quantifies spot broadening in difficult, mixed microstructure data. • Algorithm finds sparse combination of entries from dictionary of peak functions. • Approach showed asymmetric plastic response in preprocessed AA7075 T651 sample. - Abstract: High energy X-ray diffraction data collected in situ during loading experiments permits probing of the crystal structure of a plastically deforming material sample. An elastoplastic deformation is associated with heterogeneity in both crystal orientation and lattice spacing—each manifesting as azimuthal broadening and radial broadening of diffraction peaks respectively. Quantifying the spreading effect is challenging, especially in cases where the sample has a granularity between that of a single crystal and fine grain or powder material. The approach developed in this paper begins by modeling the intensity signal in the vicinity of a Debye-Scherrer ring as a sparse, nonnegative superposition of Gaussian basis functions drawn from an over-complete dictionary. Processing automatically selects from the dictionary basis functions whose widths and amplitudes are representative of the data. The chosen basis functions are used to compute scalar measures of radial and azimuthal broadening for the set of diffraction peaks composing a Debye-Scherrer ring. To demonstrate the utility of the approach, we show that analysis of diffraction peak shape information from an aluminum alloy 7075 T651 (AA7075 T651) sample provides insight into the origin of material state that would have otherwise have been difficult if not impossible to extract using conventional methods. Furthermore, the extracted information revealed a deformation response linked to the processing history of the sample.

36 MATERIALS SCIENCE↗

Primal interface debonding formulation for finite strain isotropic plasticity

In this work, a framework is developed for modeling ductile damage of nonlinear materials whose plastic deformation is characterized using rate independent classical plasticity. This method relies on the assumption that the free energy can be decomposed into elastic, plastic and damage parts. A thermodynamically consistent method is derived which satisfies the second law of thermodynamics in the Clausius–Duhem inequality form. The dissipation associated with plasticity takes place in the domain only, while damage dissipation is localized to the interface. The method is developed using Variational Multiscale ideas to obtain definitions of the interface fluxes within a primal formulation analogous to the Discontinuous Galerkin method, which ensures weakly vanishing interface gap prior to reaching a damage initiation criterion. The local nonlinear problem to calculate both plastic deformation gradient and damage variable follows an incremental approach similar to classical plasticity return mapping algorithm. This elastoplastic damage formulation is developed for material undergoing finite strain, and it naturally accommodates a trapezoidal traction separation law (TSL) whose shape can be varied to model either ductile interface behavior or brittle interface behavior. The formulation's performance is assessed through modeling a patch test and a compact tension specimen.

42 ENGINEERING↗

Phase-field modeling of the beta to omega phase transformation in Zr–Nb alloys

A three-dimensional elastoplastic phase-field model is developed, using the Finite Element Method (FEM), for modeling the athermal beta to omega phase transformation in Zr–Nb alloys by including plastic deformation and strain hardening of the material. The microstructure evolution during athermal transformation as well as under different stress states, e.g. uni-axial tensile and compressive, bi-axial tensile and compressive, shear and tri-axial loadings, is studied. The effects of plasticity, stress states and the stress loading direction on the microstructure evolution as well as on the mechanical properties are studied. The input data corresponding to a Zr – 8 at.% Nb alloy are acquired from experimental studies as well as by using the CALPHAD method. Our simulations show that the four different omega variants grow as ellipsoidal shaped particles. Our results show that due to stress relaxation, the athermal phase transformation occurs slightly more readily in the presence of plasticity compared to that in its absence. The evolution of omega phase is different under different stress states, which leads to the differences in the mechanical properties of the material. The variant selection mechanism, i.e. formation of different variants under different stress loading directions, is also nicely captured by our model.

36 MATERIALS SCIENCE↗

Topology-enhanced mechanical stability of swelling nanoporous electrodes

Abstract Materials like silicon and germanium offer a 10-fold improvement in charge capacity over conventional graphite anodes in lithium-ion batteries but experience a roughly threefold volume increase during lithiation, which challenges ensuring battery integrity. Nanoporous silicon, created by liquid-metal-dealloying, is a potentially attractive anode design to mitigate this challenge, exhibiting both higher capacity and extended cycle lifetimes. However, how nanoporous structures accommodate the large volume change is unknown. Here, we address this question by using phase-field modeling to produce nanoporous particles and to investigate their elastoplastic swelling behavior and fracture. Our simulations show that enhanced mechanical stability results from the network topology consisting of ligaments connected by bulbous, sphere-like nodes. The ligaments forcefully resist elongation while the nodes, behaving like isolated spherical particles, experience large stresses driving fracture. However, being smaller compared to a sphere of the same volume as the entire nanoporous particle, the nodes are more protected against fracture.

36 MATERIALS SCIENCE↗

A state variable for crumpled thin sheets

Despite the apparent ease with which sheets of paper are crumpled and tossed away, crumpling dynamics are often considered a paradigm of complexity. This arises from the infinite number of configurations that disordered, crumpled sheets can take. Here we experimentally show that key aspects of axially confined crumpled Mylar sheets have a very simple description; evolution of damage in crumpling dynamics can largely be described by a single global quantity—the total length of creases. We follow the evolution of the damage network in repetitively crumpled elastoplastic sheets, and show that the dynamics are deterministic, depending only on the instantaneous state of the crease network and not on the crumpling history. We also show that this global quantity captures the crumpling dynamics of a sheet crumpled for the first time. This leads to a remarkable reduction in complexity, allowing a description of a highly disordered system by a single state parameter.

42 ENGINEERING↗

Pressure Self-focusing Effect and Novel Methods for Increasing the Maximum Pressure in Traditional and Rotational Diamond Anvil Cells

The main principles of producing a region near the center of a sample, compressed in a diamond anvil cell (DAC), with a very high pressure gradient and, consequently, with high pressure are predicted theoretically. The revealed phenomenon of generating extremely high pressure gradient is called the pressure self-focusing effect. Initial analytical predictions utilized generalization of a simplified equilibrium equation. Then, the results are refined using our recent advanced model for elastoplastic material under high pressures in finite element method (FEM) simulations. The main points in producing the pressure self-focusing effect are to use beveled anvils and reach a very thin sample thickness at the center. We find that the superposition of torsion in a rotational DAC (RDAC) offers drastic enhancement of the pressure self-focusing effect and allows one to reach the same pressure under a much lower force and deformation of anvils.

42 ENGINEERING↗

Use of a Dual-Structure Constitutive Model for Predicting the Long-Term Behavior of an Expansive Clay Buffer in a Nuclear Waste Repository

Expansive soils are suitable as backfill and buffer materials in engineered barrier systems to isolate heat-generating nuclear waste in deep geological formations. The canisters containing nuclear waste would be placed in tunnels excavated at a depth of several hundred meters. The expansive soil should provide enough swelling capacity to support the tunnel walls, thereby reducing the impact of the excavation-damaged zone on the long-term mechanical and flow-barrier performance. In addition to their swelling capacity, expansive soils are characterized by accumulating irreversible strain on suction cycles and by effects of microstructural swelling on water permeability that for backfill or buffer materials can significantly delay the time it takes to reach full saturation. In order to simulate these characteristics of expansive soils, a dual-structure constitutive model that includes two porosity levels is necessary. The authors present the formulation of a dual-structure model and describe its implementation into a coupled fluid flow and geomechanical numerical simulator. The authors use the Barcelona Basic Model (BBM), which is an elastoplastic constitutive model for unsaturated soils, to model the macrostructure, and it is assumed that the strains of the microstructure, which are volumetric and elastic, induce plastic strain to the macrostructure. The authors tested and demonstrated the capabilities of the implemented dual-structure model by modeling and reproducing observed behavior in two laboratory tests of expansive clay. As observed in the experiments, the simulations yielded nonreversible strain accumulation with suction cycles and a decreasing swelling capacity with increasing confining stress. Finally, the authors modeled, for the first time using a dual-structure model, the long-term (100,000 years) performance of a generic heat-generating nuclear waste repository with waste emplacement in horizontal tunnels backfilled with expansive clay and hosted in a clay rock formation. The thermo-hydro-mechanical results of the dual-structure model were compared with those of the standard single-structure BBM. The main difference between the simulation results from the two models is that the dual-structure model predicted a time to fully saturate the expansive clay barrier on the order of thousands of years, whereas the standard single-structure BBM yielded a time on the order of tens of years. These examples show that a dual-structure model, such as the one presented here, is necessary to properly model the thermo-hydro-mechanical behavior of expansive soils.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Second-Order Inelastic Dynamic Analysis of 3D Semi-Rigid Steel Frames Under Earthquake Loads with Three Components

In this study, it has been presented an algorithm for second-order elastoplastic dynamic time-history analysis of three dimensional frames that have steel members with semirigid joints. The proposed analysis accounts for material, geometric and connection nonlinearities. Material nonlinearity have been modeled by the Ramberg-Osgood relation. While the geometric nonlinearity caused by axial force has been described by the use of the geometric stiffness matrix, the nonlinearity caused by the interaction between the axial force and bending moment has been also described by the use of the stability functions. The independent hardening model has been used to describe the nonlinear behaviour of semi-rigid connections. Dynamic equation of motion has been solved by Newmark's constant acceleration method in time history domain.

58 GEOSCIENCES↗

Analysis Of The Interface Behavior Under Cyclic Loading

This paper analyses the frictional behavior between soil and structures under cyclic loading conditions. In particular, the attention is focused on the stress degradation occurring in sand-metal interface tests and on the relevant parameters playing a role in such kind of tests. Also, the paper reports the analysis of the experimental data from the constitutive point of view with a two-surface elastoplastic model.

36 MATERIALS SCIENCE↗

Numerical Simulation Of Steel Plate Bending Process Using Stationary Laser Beam By A Coupled Finite Element Thermal Mechanical Analysis

We analyze the deformation induced by focusing a CW high power laser beam on stainless steel plate. A non-linear 3D finite element approach is used to simulate the thermo-elastoplastic deformation, the heat conduction, and stresses. Material properties including density, yield stress, Young modulus, specific heat, and thermal expansion coefficient are considered as temperature-dependent. The effect of heating time on transient temperatures, stresses, strains and bending angles during the process is studied, and the process parameters affecting the bending angles were also investigated.

36 MATERIALS SCIENCE↗

A Numerical Investigation of CFRP-Steel Interfacial Failure with Material Point Method

The success of retrofitting steel structures by using the Carbon Fibre Reinforced Polymers (CFRP) significantly depends on the performance and integrity of CFRP-steel joint and the effectiveness of the adhesive used. Many of the previous numerical studies focused on the design and structural performance of the CFRP-steel system and neglected the mechanical responses of adhesive layer, which results in the lack of understanding in how the adhesive layer between the CFRP and steel performs during the loading and failure stages. Based on the recent observation on the failure of CFRP-steel bond in the double lap shear tests, a numerical approach is proposed in this study to simulate the delamination process of CFRP sheet from steel plate using the Material Point Method (MPM). In the proposed approach, an elastoplasticity model with a linear hardening and softening law is used to model the epoxy layer. The MPM, which does not employ fixed mesh-connectivity, is employed as a robust spatial discretization method to accommodate the multi-scale discontinuities involved in the CFRP-steel bond failure process. To demonstrate the potential of the proposed approach, a parametric study is conducted to investigate the effects of bond length and loading rates on the capacity and failure modes of CFRP-steel system. The evolution of the CFRP-steel bond failure and the distribution of stress and strain along bond length direction will be presented. The simulation results not only well match the available experimental data but also provide a better understanding on the physics behind the CFRP sheet delamination process.

36 MATERIALS SCIENCE↗

Numerical simulation of spall in lead accounting for its occurrence in solid as well as liquid phases

The capabilities of a recently-developed continuum-level model developed for the purpose of predicting the evolution of spall, including the compaction of damaged material, and applicable to the formation of spall in the material that is fully solid as well as material that is locally liquid, are evaluated against empirical data for lead. Here, the model accounts for inertial forces, elastoplastic constitutive behavior, viscosity, and surface tension. Predictions of spall layer thickness are shown to match the empirical data reasonably well.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Dynamically reinforced heterogeneous grain structure prolongs ductility in a medium-entropy alloy with gigapascal yield strength

Ductility, i.e., uniform strain achievable in uniaxial tension, diminishes for materials with very high yield strength. Even for the CrCoNi medium-entropy alloy (MEA), which has a simple face-centered cubic (FCC) structure that would bode well for high ductility, the fine grains processed to achieve gigapascal strength exhaust the strain hardening ability such that, after yielding, the uniform tensile strain is as low as ~2%. Here we purposely deploy, in this MEA, a three-level heterogeneous grain structure (HGS) with grain sizes spanning the nanometer to micrometer range, imparting a high yield strength well in excess of 1 GPa. This heterogeneity results from this alloy’s low stacking fault energy, which facilitates corner twins in recrystallization and stores deformation twins and stacking faults during tensile straining. After yielding, the elastoplastic transition through load transfer and strain partitioning among grains of different sizes leads to an upturn of the strain hardening rate, and, upon further tensile straining at room temperature, corner twins evolve into nanograins. This dynamically reinforced HGS leads to a sustainable strain hardening rate, a record-wide hysteresis loop in load–unload–reload stress–strain curve and hence high back stresses, and, consequently, a uniform tensile strain of 22%. As such, this HGS achieves, in a single-phase FCC alloy, a strength–ductility combination that would normally require heterogeneous microstructures such as in dual-phase steels.

36 MATERIALS SCIENCE↗