SEARCH · Search NASA
Results for “electrokinetics”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electrophoretic and potentiometric signatures of multistage CaCO3 nucleation
HYPOTHESIS: Calcium carbonate nucleation is often a complex and multistep process that is difficult to follow in situ. The time-resolved electrochemical and electrophoretic methods can provide a new insight into the nucleation pathway. EXPERIMENTS: Here, we used a combination of speciation calculations with time-resolved electrophoretic and potentiometric methods to monitor calcium carbonate precipitation from a slightly supersaturated solution. FINDINGS: After an initial mixing period of three minutes in which metastable CaCO 3 phases may have nucleated and subsequently dissolved due to locally-high supersaturations, bulk solution pH and Ca 2+ concentrations stabilize before decreasing in tandem with the precipitation of a CaCO 3 phase. After an hour, the precipitate is dominated by calcite that grows at the expense of dissolving vaterite. The time-dependent electrokinetic potential shows analogous signatures of multistage nucleation process: initial rapid changes in ζ-potential are followed by much slower equilibration starting about one hour after reagents are mixed. The changes in ζ-potential, solution pH, saturation indexes, and particle morphology are consistent with vaterite to calcite transformation via dissolution of the former and recrystallization of the latter. These findings highlight the potential use of ζ-potential measurements for monitoring polymorphic transformations of carbonate phases in-situ.
Breakdown of electroneutrality in nanopores
Ion transport in extremely narrow nanochannels has gained increasing interest in recent years due to unique physical properties at the nanoscale and the technological advances that allow us to study them. It is tempting to approach this confined regime with the theoretical tools and knowledge developed for membranes and microfluidic devices, and naively apply continuum models, such as the Poisson-Nernst-Planck and Navier-Stokes equations. However, it turns out that some of the most basic principles we take for granted in larger systems, such as the complete screening of surface charge by counter-ions, can break down under extreme confinement. Additionally, we show that in a truly one-dimensional system of ions interacting with three-dimensional electrostatic interactions, the screening length is exponentially large, and can easily exceed the macroscopic length of a nanotube. Without screening, electroneutrality breaks down within the nanotube, with fundamental consequences for ion transport and electrokinetic phenomena. In this work, we build a general theoretical framework for electroneutrality breakdown in nanopores, focusing on the most interesting case of a one-dimensional nanotube, and show how it provides an elegant interpretation for the peculiar scaling observed in experimental measurements of ionic conductance in carbon nanotubes.
Unseeded, spontaneous nucleation of spherulitic magnesium calcite
Most of the sedimentary carbonates deposited in the marine environments are composed of calcium carbonate minerals with varying amounts of incorporated Mg 2+ . However, understanding how interactions of impurities with carbonate and their incorporation affect sediments behavior remains a challenge. Here, a new insight is obtained by monitoring solution composition, morphology, and electrokinetic potential of carbonate particles formed in a spontaneous unseeded batch precipitation experiment using electrochemical and scanning electron microscopy methods. The solid composition and growth rate are extracted from changes in the bulk composition and fitted to chemical affinity rate law, revealing that the precipitation pathway consists of second-order dissolution and first-order precipitation. The molecular dynamics simulations show that the lattice strain induced by randomly substituting Ca 2+ by Mg 2+ stabilizes spherical nanoparticles and reduces their surface area and volume. Combining kinetics and thermodynamics insight, we conclude that variation in the carbonate bulk and interfacial energies, along with the solution supersaturation, lead to the dissolution-precipitation transformation pathway from Mg-rich to Mg-poor carbonate phase that preserves spherulitic morphology. Furthermore, our findings are relevant for long-standing questions of how impurities influence diagenesis of carbonate sediments and spherulitic carbonate particles' origin.
Hybrid immersed interface-immersed boundary methods for AC dielectrophoresis
Dielectrophoresis, a nonlinear electrokinetic transport mechanism, has become popular in many engineering applications including manipulation, characterization and actuation of biomaterials, particles and biological cells. In this paper, we present a hybrid immersed interface–immersed boundary method to study AC dielectrophoresis where an algorithm is developed to solve the complex Poisson equation using a real variable formulation. An immersed interface method is employed to obtain the AC electric field in a fluid media with suspended particles and an immersed boundary method is used for the fluid equations and particle transport. The convergence of the proposed algorithm as well as validation of the hybrid scheme with experimental results is presented. In this paper, the Maxwell stress tensor is used to calculate the dielectrophoretic force acting on particles by considering the physical effect of particles in the computational domain. Thus, this study eliminates the approximations used in point dipole methods for calculating dielectrophoretic force. A comparative study between Maxwell stress tensor and point dipole methods for computing dielectrophoretic forces are presented. The hybrid method is used to investigate the physics of dielectrophoresis in microfluidic devices using an AC electric field. The numerical results show that with proper design and appropriate selection of applied potential and frequency, global electric field minima can be obtained to facilitate multiple particle trapping by exploiting the mechanism of negative dielectrophoresis. Our numerical results also show that electrically neutral particles form a chain parallel to the applied electric field irrespective of their initial orientation when an AC electric field is applied. This proposed hybrid numerical scheme will help to better understand dielectrophoresis and to design and optimize microfluidic devices.
Computation of stationary 3D halo currents in fusion devices with accuracy control
This paper addresses the calculation of the resistive distribution of halo currents in three-dimensional structures of large magnetic confinement fusion machines. A Neumann electrokinetic problem is solved on a geometry so complicated that complementarity is used to monitor the discretization error. An irrotational electric field is obtained by a geometric formulation based on the electric scalar potential, whereas three geometric formulations are compared to obtain a solenoidal current density: a formulation based on the electric vector potential and two geometric formulations inspired from mixed and mixed-hybrid Finite Elements. The electric vector potential formulation is usually considered impractical since an enormous computing power is wasted by the topological pre-processing it requires. To solve this challenging problem, we present novel algorithms based on lazy cohomology generators that enable to save orders of magnitude computational time with respect to all other state-of-the-art solutions proposed in literature. Believing that our results are useful in other fields of scientific computing, the proposed algorithm is presented as a detailed pseudocode in such a way that it can be easily implemented.
Insights into Ti doping for stabilizing the Na 2/3 Fe 1/3 Mn 2/3 O 2 cathode in sodium ion battery
Iron- and manganese-based layered metal oxides, as cathodes for sodium ion batteries, have received widespread attention because of the low cost and high specific capacity. However, the Jahn-teller effect of Mn 3+ ions and the resulted unstable structure usually lead to continuously capacity decay. Herein, Titanium (Ti) has been successfully doped into Na 2/3 Fe 1/3 Mn 2/3 O 2 to suppress the Jahn-Teller distortion and improve both cycling and rate performance of sodium ion batteries. In situ high-energy synchrotron X-ray diffraction study shows that Ti-doped compound (Na 2/3 Fe 1/3 Mn 0.57 Ti 0.1 O 2 ) can maintain the single P2 phase without any phase transition during the whole charging/discharging process. Further, various electrochemical characterizations are also applied to explore the better kinetics of sodium ions transfer in the Na 2/3 Fe 1/3 Mn 0.57 Ti 0.1 O 2 . This work provides a comprehensive insight into the Ti-doping effects on the performance from both structural and electrokinetic perspectives.
Physicochemical and catalytic properties of Au nanorods micro-assembled in solvents of varying dipole moment and refractive index
Highlights: • Physicochemical activities of Au nanorods in water largely differ from organic solvents. • Au nanorods agglomeration increased with dipole moments of different polar solvents. • Refractive indexes of Au nanorods dispersion in various polar solvents are enhanced. • Electrokinetics significantly altered depending on agglomerated size of Au nanorods. • Catalysis or co-catalysis activity is varied as per the extent of Au nanorods coagulation. - Abstract: This paper deals with the impact of dipole moment (1.66–3.96 D) and refractive index (1.333–1.422) of the dispersion solvent on the plasmon absorption, surface charge, zeta potential, and adsorption properties of Au nanorods (AuNRs). AuNRs (length ≈ 53 nm and width ≈ 20 nm) undergo agglomeration (size 50–180 nm) with increase in the dipole moment of solvent (iPrOH < MeOH < DMF < DMSO). Whereas, no such coagulation occurs in H{sub 2}O and CCl{sub 4} suspension as confirmed by DLS and TEM size distribution. The electrostatic interaction of AuNRs with its surface adsorbed solvent dipoles leads to alteration of the their ionic state, absolute electronic charge and zeta potential (+49.79 mV in H{sub 2}O, +8.99 mV in DMF and −4.65 mV in MeOH dispersion) to a greater extent. This interaction distinctly modifies the adsorption behavior of polar molecules like p-nitrophenol and salicylic acid on AuNRs surface, as evidenced by the measured changes in their electro-kinetic parameters. As a result, we observe a substantial difference in catalytic and co-catalytic activities of AuNRs dispersed in various solvents as mentioned above because the catalytic properties of AuNRs are strongly dependent on the type of solvent in which they are dispersed.
Reactivity Descriptors for Direct Methanol Fuel Cell Anode Catalysts
We have investigated the anode reaction in direct methanol fuel cells using a database of adsorption free energies for 16 intermediates on 12 close-packed transition metal surfaces calculated with periodic, selfconsistent, density functional theory (DFT–GGA). This database, combined with a simple electrokinetic model of the methanol electrooxidation reaction, yields mechanistic insights that are consistent with previous experimental and theoretical studies on Pt, and extends these insights to a broad spectrum of other transition metals. In addition, by using linear scaling relations between the adsorption free energies of various intermediates in the reaction network, we find that the results determined with the full database of adsorption energies can be estimated by knowing only two key descriptors for each metal surface: the free energies of OH and CO on the surface. Two mechanisms for methanol oxidation to CO₂ are investigated: an indirect mechanism that goes through a CO intermediate and a direct mechanism where methanol is oxidized to CO₂ without the formation of a CO intermediate. For the direct mechanism, we find that, because of CO poisoning, only a small current will result on all non-group 11 transition metals; of these metals, Pt is predicted to be the most active. For methanol decomposition via the indirect mechanism, we find that the onset potential is limited either by the ability to activate methanol, by the ability to activate water, or by surface poisoning by CO* or OH*/O*. Among pure metals, there is no obvious candidate for a good anode catalyst, and in order to design a better catalyst, one has to look for bi-functional surfaces such as the well-studied PtRu alloy.
Preparation, Applications, and Digital Simulation of Carbon Interdigitated Array Electrodes
Carbon interdigitated array (IDA) electrodes with features sizes down to 1.2 μm were fabricated by controlled pyrolysis of patterned photoresist. Cyclic voltam-metry of reversible redox species produced the expected steady-state currents. The collection efficiency depends on the IDA electrode spacing, which ranged from around 2.7 to 16.5 μm, with the smaller dimensions achieving higher collection efficiencies of up to 98%. The signal amplification because of redox cycling makes it possible to detect species at relatively low concentrations (10–5 molar) and the small spacing allows detection of transient electrogenerated species with much shorter lifetimes (submillisecond). Digital simulation software that accounts for both the width and height of electrode elements as well as the electrode spacing was developed to model the IDA electrode response. The simulations are in quantitative agreement with experimental data for both a simple fast one electron redox reaction and an electron transfer with a following chemical reaction at the IDAs with larger gaps whereas currents measured for the smallest IDA electrodes, that were larger than the simulated currents, are attributed to convection from induced charge electrokinetic flow. This work was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the Department of Energy, Office of Science Office of Basic Energy Sciences.
Reversible Disorder-to-Order Transition Induced by Aqueous Lithiation in Vanadate Electrode Materials
Vanadium-based oxides are intriguing electrode materials in aqueous electrochemical systems owing to their low cost and high theoretical capacity for alkali storage, especially lithium (Li) ions. However, a sequence of phase transformations and irreversible structure distortion upon Li-ion intercalation causes structural instability and has been a lingering problem for vanadium oxide electrodes. Here, in this work, we investigate lithium vanadate (Li–V 3 O 8 ) for aqueous Li-ion intercalation and deintercalation processes. Unlike its crystalline V 2 O 5 polymorph, Li–V 3 O 8 retains monophasic lithiation, which is attributed to its disordered crystalline nature and large interplanar distance. Importantly, we show a unique and reversible sequence of disorder-to-order structural transition induced by the extent of lithiation, which indicates sequential interlayer and intralayer lithiation process, and vice versa in delithiation process, supported by electrokinetic analysis, in situ X-ray diffraction (XRD), and Debye scattering simulations. The absence of distortive phase transitions and multilithiation pathways facilitates Li-ion diffusion across the vanadate electrode materials to improve storage capacity. This work opens a new dimension for vanadium-based disordered oxides, accelerating the development of low-cost, aqueous electrochemical systems.
Intercalation-Induced Amorphization Boosts Aqueous Magnesium-Ion Storage
The design of aqueous battery cathode materials that can store divalent ions with high capacity and satisfactory reversibility is of great technical importance and challenge. Here, we report that divalent Mg 2+ storage is facilitated by an intercalation-induced amorphization of vanadate electrode materials. Electrokinetic analyses and in situ synchrotron X-ray diffraction and absorption spectroscopy collectively demonstrate that vanadate layered materials (Li–V 3 O 8 ) undergo a structural transformation to amorphization induced by Mg 2+ intercalation, and a reversible restoration of crystalline structure upon Mg 2+ deintercalation. Debye scattering simulations suggest that intercalation-induced turbostratic disorder, especially random rotations, translational shifts, oscillatory motions, or varied interlayer spacing of adjacent V–O molecular layers, could be responsible for the observed amorphization. The highly distorted local structure, in turn, facilitates Mg 2+ intercalation across the vanadate electrode materials, responsible for nearly 3/7 of the total Mg 2+ ions intercalated. The study presented reveals an intriguing relationship between ion transport and the reversible amorphization-to-crystallization dynamics it induces, opening a paradigm for designing advanced aqueous battery electrodes.
Higher Ion Selectivity with Lower Energy Usage Promoted by Electro-osmotic Flow in the Transport through Conical Nanopores
The tradeoff between selectivity and throughput presents fundamental challenges to improve desalination and charge storage, salinity gradient-based energy harvesting, memory device/circuit development, and so forth. The well-known ion-current rectification and the recently resolved time-dependent transport hysteresis in conical nanopores or asymmetric nanointerfaces offer new opportunities for the selective transport of matter. This report shows that electro-osmotic flow (EOF) is an overlooked factor that increases ion selectivity while maintaining enhanced transport throughput in rectified nanoscale electrokinetic transport. The increased selectivity originates primarily from the suppression of anion flux by the fluid flow in the opposite direction under the applied electrical field. By solving the Poisson and Nernst–Planck (PNP) equations without and with coupled Navier–Stokes (PNP–NS) equations, the EOF effects on cation and anion transport are unequivocally revealed in asymmetric nanopipettes. The flux of cations and anions as well as the transference number and flow velocity are elucidated using the models and boundary conditions validated by previous experiments. A dimensionless parameter, radius over the Debye length, reveals optimal ion selectivity and energy cost at intermediate ion concentrations and nanopore sizes, up to hundreds of millimolars and tens of nanometers under time-dependent potential stimulus. Furthermore, the fundamental insights into EOF at nanointerfaces suggest new routes/strategies for better separation, analysis, and energy applications.
Selective Ion Enrichment and Charge Storage through Transport Hysteresis in Conical Nanopipettes
Greater selectivity and controls in the ion transport dynamics are essential in fields such as charge storage, separation, energy storage and conversion, neuromorphic computing and learning, electrochemistry, to name a few. Mechanistic insights into the intriguing hysteresis effects in the rectified electrokinetic transport through single conical nanopipettes are unveiled by combining time-resolved electroanalytical experiments with numeric simulation. Cations as counterions for surface charges are found to dominate not just the through-nanopore flux but also the hysteresis charges, that is, the net enriched or expelled charges during the transport process. Built on our earlier report on the through-nanopore ion flux dominated by counterions for surface charges, the “trapped ions” or hysteresis charges are analyzed herein. Cation selectivity is almost 100% in the hysteresis charges during the potential scans in low conductivity states driven by the combined applied and intrinsic surface electrical fields. Surprisingly, the cation selectivity in the total hysteresis charges remains high at 70–80% over a wide bulk concentration range in the high conductivity (HC) states, where higher ionic strength due to ion enrichment would decrease electrostatistic effects and thus ion selectivity. The retained high selectivity at HC is explained by the competition effects of electroosmotic flow against the co-ion migration. Furthermore, the respective cation and anion portions in the total hysteresis charges over a wide range of ionic strength and measurement conditions provide generalizable strategies for improvements in both transport throughput and selectivity.
Dynamics of Electric Polarization and Relaxation of Ions at Humid Calcite Surfaces
Mobile ions at mineral surfaces can respond to an applied electric field, adopting a new distribution that effectively represents polarization of the electrical double layer. When the field is released, the ions relax to their equilibrium distribution. In both cases, the dynamics are characteristic of the interface. However, current models of electrokinetic phenomena are not sufficiently robust to accurately predict collective ion dynamics at structurally and chemically specific mineral–water interfaces. Here, in this study, we use electrostatic force microscopy (EFM) to investigate the dynamics of ion relaxation at hydrated calcite (104) surfaces at controlled relative humidity (RH). Electrically biased probes are used to polarize the distributions of calcium and carbonate ions that are intrinsic to this interface across a range of RH values. Polarization kinetics are tracked by monitoring the tip–sample force gradient during charging, and EFM imaging is used to characterize the spatial relaxation dynamics after the applied field is released. Electrostatic finite element modeling of the sample/probe system across length-scales from nanometers to millimeters reproduces the observed stretched exponential charging response. Together, these results allow us to estimate the ion diffusivities at the interface across a wide range of RH values. These diffusivities increase by roughly 5 orders of magnitude as the RH is increased from 5 to 90%, highlighting the critical role of adsorbed water for surface ion solvation that enables ion mobility.
Label-Free Anti-Brownian Trapping of Single Nanoparticles in Solution
Today, biomolecular nanoparticles are prevalent as diagnostic tools and molecular delivery carriers, and it is particularly useful to examine individuals within a sample population to quantify the variations between objects and directly observe the molecular dynamics involving these objects. Using interferometric scattering as a highly sensitive label-free detection scheme, we recently developed the interferometric scattering anti-Brownian electrokinetic (ISABEL) trap to hold a single nanoparticle in solution for extended optical observation. In this perspective, we describe how we implemented this trap, how it extends the capabilities of previous ABEL traps, and how we have begun to study individual carboxysomes, a fascinating biological carbon fixation nanocompartment. By monitoring single nanocompartments for seconds to minutes in the ISABEL trap using simultaneous interferometric scattering and fluorescence spectroscopy, we have demonstrated single-compartment mass measurements, cargo-loading trends, and redox sensing inside individual particles. These experiments benefit from rich multiplexed correlative measurements utilizing both scattering and fluorescence with many exciting future capabilities within reach.
Electroosmotic Flow Rectification in Membranes with Asymmetrically Shaped Pores: Effects of Current and Pore Density
We have recently demonstrated a new electrokinetic phenomenon—electroosmotic flow rectification in membranes with asymmetrically shaped pores. Flow rectification means that at constant driving force the flow rate in one direction through the membrane is faster than the flow rate in the opposite direction. EOF rectification could be of practical use in microfluidic devices incorporating porous membranes, but additional research is required. As such, we explore here the effects of two key experimental variables—current density used to drive flow through the membrane and membrane pore density—on EOF rectification. We have found that the extent of EOF rectification, as quantified by the rectification ratio, increases with increasing current density. In contrast, the rectification ratio decreases with increasing membrane pore density. We propose explanations for these results based on simple EOF and membrane-transport theories.
Hydrogen and Electric Power Generation from Liquid Microjets: Design Principles for Optimizing Conversion Efficiency
Historically, Liquid water microjets have been successfully employed for both electrical power generation and gaseous hydrogen production, but the demonstrated efficiencies have been low. Here, we employ a combination of a modified Poisson-Boltzmann description, continuum hydrodynamic equations, and microjet electrokinetic experiments to gain detailed insight into the origin of the streaming currents produced in pure water. We identify the contributions to the streaming current from specific ion adsorption at the solid/liquid interface and from long-ranged electrostatic interactions, finding that the portion originating from the latter dominate at charged surfaces. The detailed understanding afforded by theory and the close agreement with experimental results elucidates design principles for optimizing hydrogen production and power generation. Changing the sign of the surface charge density through targeted use of surface coatings via silanization switches the primary charge carrier between hydronium and hydroxide and therefore switches the corresponding production of molecular hydrogen to oxygen at the target electrode. Moreover, hydrophobic surface coatings reduce dissipation due to fluid/solid friction, thereby increasing the conversion efficiency.