Search NASA⌕ Search

SEARCH · Search NASA

Results for “electron micrograph”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

149 records · Page 9

A study of the UV and VUV degradation of FEP

UV and VUV degradation of fluorinated ethylene propylene (FEP) copolymer was studied using electron spin resonance (ESR) spectroscopy, x-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The ESR study revealed the formation of a terminal polymer radical. The stability of this radical was investigated under different environments. An XPS study of FEP film exposed to VUV and atomic oxygen showed that oxidation takes place on the polymer surface. The study revealed also that the percentage of CF2 in the polymer surface decreased with exposure time and the percentage of CF, CF3, and carbon attached to oxygen increased. SEM micrographs of FEP film exposed to VUV and atomic oxygen identified a rough surface with undulations similar to sand dunes.

George, Graeme A.↗

EBIC investigation of hydrogenation of crystal defects in EFG solar silicon ribbons

Changes in the contrast and resolution of defect structures in 205 Ohm-cm EFG polysilicon ribbon subjected to annealing and hydrogenation treatments were observed in a JEOL 733 Superprobe scanning electron microscope, using electron beam induced current (EBIC) collected at an A1 Schottky barrier. The Schottky barrier was formed by evaporation of A1 onto the cleaned and polished surface of the ribbon material. Measurement of beam energy, beam current, and the current induced in the Schottky diode enabled observations to be quantified. Exposure to hydrogen plasma increased charge collection efficiency. However, no simple causal relationship between the hydrogenation and charge collection efficiency could be inferred, because the collection efficiency also displayed an unexpected thermal dependence. Good quality intermediate-magnification (1000X-5400X) EBIC micrographs of several specific defect structures were obtained. Comparison of grown-in and stress-induced dislocations after annealing in vacuum at 500 C revealed that stress-induced dislocations are hydrogenated to a much greater degree than grown-in dislocations. The theoretical approximations used to predict EBIC contrast and resolution may not be entirely adequate to describe them under high beam energy and low beam current conditions.

Sullivan, T.↗

Surface topographical effects on the structural growth of thick sputtered metal and alloy coatings

Thick sputtered S-Monel, silver, and 304 stainless steel coatings were deposited on mica and metal substrates with various surface finishes to investigate the structural growth of the coating by scanning electron microscopy. The geometry and the surface structure of the nodules are characterized. Compositional changes within the coating were analyzed by X-ray dispersion microscopy. Defects in the surface finish (i.e., scratches, inclusions, etc.) act as preferential nucleation sites and form isolated and complex nodules and various surface overgrowths in the coating. The nodule boundaries are very vulnerable to chemical etching and these nodules do not disappear after full annealing. Further, they have undesirable effects on mechanical properties; cracks are initiated at the nodules when the coating is stressed by mechanical forces. These effects are illustrated by micrographs. Nodular growth within a coating can be minimized or eliminated by reducing the surface roughness.

Spalvins, T.↗

Nodular growth in thick-sputtered metallic coatings

Thick-sputtered S-Monel, silver, and 304 stainless steel coatings were deposited on mica and metal substrates with various surface finishes to investigate the nodular growth in the coating by scanning electron microscopy. The geometry and the surface structure of the nodules are characterized. Compositional changes within the coating were analyzed by energy dispersive X-ray analysis. Defects in the surface finish (i.e., scratches, inclusions, etc.), act as preferential nucleation sites and form isolated and complex nodules and various surface overgrowths in the coating. The nodule boundaries are very vulnerable to chemical etching and these nodules do not disappear after full annealing. Further, they have undesirable effects on mechanical properties; cracks are initiated at the nodules when the coating is stressed by mechanical forces. These effects are illustrated by micrographs. Nodular growth within a coating can be minimized or eliminated by increasing the surface smoothness.

Spalvins, T.↗

Revival of Dobell's "chromidia" hypothesis: chromatin bodies in the amoebomastigote Paratetramitus jugosus

Multiple fission of a mature Paratetramitus jugosus (approx. 10 micrometers long) resulted in the production of many small, roughly spherical (2-7 micrometers in diameter) amoebae. Our observation of live material and examination of over two hundred micrographs lead us to suggest that DNA-containing membrane-bounded chromatin bodies bud amitotically from the nucleus. DAPI-stained bodies of these were observed in the cytoplasm of amoebae, mastigotes, and cysts, and at least some of these chromatin bodies seemed to be released into the medium. This interpretation revives for P. jugosus the "chromatin hypothesis" of Dobell. Our data, consistent with the descriptions of Dobell, Hogue, and Wherry, indicate that encysting amoebae may reproduce by chromidia. Dobell's original chromidia concept was limited to amoebae. Others claimed for it far-reaching consequences: "chromidia" were touted as an explanation for embryogenesis and histogenesis of metazoa. Although there is no evidence for chromidia in animals, outright rejection of Dobell's chromidia hypothesis sensu stricto as an amitotic multiple fission process in amoebae is unjustified.

Non-NASA Center↗