Search NASA⌕ Search

SEARCH · Search NASA

Results for “end effector”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Design for a Three-Fingered Hand

A general purpose end-effector for use on the space manipulator proposed for the shuttle program was developed. The end-effector has the capabilities of a human hand and peel-off value as a human prosthetic device. The design evolved through two mock-up stages. The final form contains four electric motors. While thumb and forefinger bend, their ultimate phalanges maintain a parallel stance to one another. The grip centerline is at 45 degrees to the mounting base.

Crossley, F. R. E.↗
NASA NTRS1991

A vision-based end-point control for a two-link flexible manipulator

The measurement and control of the end-effector position of a large two-link flexible manipulator are investigated. The system implementation is described and an initial algorithm for static end-point positioning is discussed. Most existing robots are controlled through independent joint controllers, while the end-effector position is estimated from the joint positions using a kinematic relation. End-point position feedback can be used to compensate for uncertainty and structural deflections. Such feedback is especially important for flexible robots. Computer vision is utilized to obtain end-point position measurements. A look-and-move control structure alleviates the disadvantages of the slow and variable computer vision sampling frequency. This control structure consists of an inner joint-based loop and an outer vision-based loop. A static positioning algorithm was implemented and experimentally verified. This algorithm utilizes the manipulator Jacobian to transform a tip position error to a joint error. The joint error is then used to give a new reference input to the joint controller. The convergence of the algorithm is demonstrated experimentally under payload variation. A Landmark Tracking System (Dickerson, et al 1990) is used for vision-based end-point measurements. This system was modified and tested. A real-time control system was implemented on a PC and interfaced with the vision system and the robot.

Obergfell, Klaus↗
NASA NTRS1976

Shuttle remote manipulator system workstation - Man-machine engineering

A major subsystem aboard the Shuttle Orbiter, the Remote Manipulator System (RMS) provides the capability to deploy and retrieve free-flying satellites, support attached payload operations, and aid in crewmember rescue from a disabled vehicle should the requirement arise. The Remote Manipulator System consists of 15.3-m (50 ft) articulated booms, end effectors, operator workstation, and closed circuit video, power and control subsystems. The manipulator booms (or arms) and end effectors are located in the Orbiter payload bay and operated from inside the cabin by one crewmember. This paper is primarily concerned with the design and development of the RMS operator's workstation, the man-machine engineering features and interfaces, and man-in-the-loop simulations and testing results obtained to date by the National Aeronautics and Space Administration (NASA).

Brown, J. W.↗
NASA NTRS1994

Robotic Booking Of Coolant Tubes

Robotic tube-booking subsystem proposed for use in automated manufacturing cell described in "Robotic Processing of Rocket-Engine Nozzles" (MFS-29927). Includes electric or pneumatic end effector that inspects gaps under guidance of control processor connected to robotic vision subsystem. After inspecting each gap, end effector books tubes in vicinity, then reinspects to ensure attainment of desired gap. Makes entire tube-gap area brazeable, without damage to tubes, with consistent results. In addition, robotic booking takes less time and costs less than manual booking.

Wagner, Garret E.↗
NASA NTRS1987

Path Planning with obstacle avoidance

The research report here summarizes a solution for two dimensional Path Planning with obstacle avoidance in a workspace with stationary obstacles. The solution finds the shortest path for the end effector of a manipulator arm. The program uses an overhead image of the robot work space and the starting and ending positions of the manipulator arm end effector to generate a search graph which is used to find the shortest path through the work area. The solution was originally implemented in VAX Pascal, but was later converted to VAX C.

Krause, Donald M.↗
NASA NTRS1990

Task decomposition for multilimbed robots to work in the reachable-but-unorientable space

Multilimbed industrial robots that have at least one arm and two or more legs are suggested for enlarging robot workspace in industrial automation. To plan the motion of a multilimbed robot, the arm-leg motion-coordination problem is raised and task decomposition is proposed to solve the problem; that is, a given task described by the destination position and orientation of the end-effector is decomposed into subtasks for arm manipulation and for leg locomotion, respectively. The former is defined as the end-effector position and orientation with respect to the legged main body, and the latter as the main-body position and orientation in the world coordinates. Three approaches are proposed for the task decomposition. The approaches are further evaluated in terms of energy consumption, from which an optimal approach can be selected.

Su, Chao↗
NASA NTRS1992

Configuration control of seven-degree-of-freedom arms

A seven degree of freedom robot arm with a six degree of freedom end effector is controlled by a processor employing a 6 by 7 Jacobian matrix for defining location and orientation of the end effector in terms of the rotation angles of the joints, a 1 (or more) by 7 Jacobian matrix for defining 1 (or more) user specified kinematic functions constraining location or movement of selected portions of the arm in terms of the joint angles, the processor combining the two Jacobian matrices to produce an augmented 7 (or more) by 7 Jacobian matrix, the processor effecting control by computing in accordance with forward kinematics from the augmented 7 by 7 Jacobian matrix and from the seven joint angles of the arm a set of seven desired joint angles for transmittal to the joint servo loops of the arm. One of the kinematic functions constraints the orientation of the elbow plane of the arm. Another one of the kinematic functions minimizes a sum of gravitational torques on the joints. Still another kinematic function constrains the location of the arm to perform collision avoidance. Generically, one kinematic function minimizes a sum of selected mechanical parameters of at least some of the joints associated with weighting coefficients which may be changed during arm movement. The mechanical parameters may be velocity errors or gravity torques associated with individual joints.

Seraji, Homayoun↗
NASA NTRS1991

Task decomposition for a multilimbed robot to work in reachable but unorientable space

Robot manipulators installed on legged mobile platforms are suggested for enlarging robot workspace. To plan the motion of such a system, the arm-platform motion coordination problem is raised, and a task decomposition is proposed to solve the problem. A given task described by the destination position and orientation of the end effector is decomposed into subtasks for arm manipulation and for platform configuration, respectively. The former is defined as the end-effector position and orientation with respect to the platform, and the latter as the platform position and orientation in the base coordinates. Three approaches are proposed for the task decomposition. The approaches are also evaluated in terms of the displacements, from which an optimal approach can be selected.

Su, Chau↗
NASA NTRS1995

Configuration control of seven degree of freedom arms

A seven-degree-of-freedom robot arm with a six-degree-of-freedom end effector is controlled by a processor employing a 6-by-7 Jacobian matrix for defining location and orientation of the end effector in terms of the rotation angles of the joints, a 1 (or more)-by-7 Jacobian matrix for defining 1 (or more) user-specified kinematic functions constraining location or movement of selected portions of the arm in terms of the joint angles, the processor combining the two Jacobian matrices to produce an augmented 7 (or more)-by-7 Jacobian matrix, the processor effecting control by computing in accordance with forward kinematics from the augmented 7-by-7 Jacobian matrix and from the seven joint angles of the arm a set of seven desired joint angles for transmittal to the joint servo loops of the arms. One of the kinematic functions constrains the orientation of the elbow plane of the arm. Another one of the kinematic functions minimizing a sum of gravitational torques on the joints. Still another one of the kinematic functions constrains the location of the arm to perform collision avoidance. Generically, one of the kinematic functions minimizes a sum of selected mechanical parameters of at least some of the joints associated with weighting coefficients which may be changed during arm movement. The mechanical parameters may be velocity errors or position errors or gravity torques associated with individual joints.

Seraji, Homayoun↗
NASA NTRS2023

Spaceflight Autonomous Multigenerational Microbial Sequencer (SAMMS) in Support of Plant-Growth Systems

As the National Aeronautics and Space Association (NASA) begins to pursue long-duration space flights, they will need to be able to provide astronauts with a nutritious and reliable food source. To meet the administration’s goal of traveling to the Moon and Mars, astronauts will need to begin to grow their own food in space. To protect their food source, extensive monitoring will occur to test for the effects of a space flight environment (e.g., radiation) as well as for early pathogen and disease detection. Genomic sequencing allows for both concerns to be tested on a regular basis. However, NASA’s current sequencer is unable to process plant tissues. Therefore, a novel method for plant DNA extraction using microneedle (MN) patches that will be able to feed into NASA’s existing system, but also require minimal human input is proposed. To support this, the design was broken down into four components (1) MN patch fabrication (2) MN patch extraction, (3) automated sampling motion control, and (4) a processing module. The MN patch is fabricated using a custom mold with conically shaped needles. The mold is filled with Polyvinyl alcohol (PVA) solution and placed in a vacuum desiccator. The mold is left in the vacuum overnight until the patch is dry and ready for use. The protocol was tested with varying pressures, drying times, volume amounts, and preparation methods to determine if highquality needles can be produced. A MN is a method of DNA extraction where the patch is applied to a leaf, the needles penetrate the leaf, breaking the rigid plant cell wall to isolate the DNA. A protocol for this method of extraction was tested to ensure the patch could produce the needed yield and purity. The tests varied by the number of patches, number of applications, and plant type. To automate the MN extraction method, motion control will utilize two separate axis tables which move in the x and y directions. The y-axis table will have an end effector that fits a MN patch and will have the ability to apply the patch to the leaf sample. This end effector will also act as a lid for a downstream processing module. The other axis will position the leaf sample and processing container so that the patch can be applied accurately. The Joint Comprehensive Sequencing System (JCSS) module integrates all the components together. The output of this module feeds into the NASA Charged Information-Storage Polymer Preparation System (CHIPPS) for genomic sequencing. The extraction module operates using a series of syringes and tubing to pump the varying reagents needed for the extraction protocol. The results of the study proved that MN patches are a viable method of DNA extraction. While fabrication of high-quality needles was unsuccessful, the protocol was able to be further developed using centrifugation. The integrated design between the motion control and the JCSS enabled the potential for automation with a complete conceptual design and prototype. Future research and development for this study would include (1) further testing for fabrication (2) expanding the range of plant species compatible with the MN patch, and (3) building a working prototype for the integrated system.

Peter Ling↗
NASA NTRS1987

Dynamic sensing of 6-axis external force and moment applied to a robot end

A dynamic force sensing method is proposed for a robot manipulator. A 6-axis wrist force sensor which is commonly used for robot force sensing does not take the direct measurement of the force and moment applied to an end effector externally from the environment of the manipulator, but takes the resultant of the gravity, the inertial force and moment on the end effector, and the external force and moment. The separation of gravitational and inertial force and moment from the measurement of the force sensor is crucial to achieving dynamically accurate force sensing and fast manipulator motion under force feedback control. A mathematical model is derived for the force sensing process and the separation of the force and moment as a nonlinear optimal state estimation problem formulated. Then an approximate solution is given using extended Kalman filtering techniques.

Yokota, Masaru Uchiyama↗
NASA NTRS1987

Telerobotics - Display, control, and communication problems

An experimental telerobotics simulation is described suitable for studying human operator (HO) performance. Simple manipulator pick-and-place and tracking tasks allowed quantitative comparison of a number of calligraphic display viewing conditions. An enhanced perspective display was effective with a reference line from target to base, with or without a complex three-dimensional grid framing the view. This was true especially if geometrical display parameters such as azimuth and elevation were arranged to be near optimal. Quantitative comparisons were made possible, utilizing control performance measures such as root mean square error. There was a distinct preference for controlling the manipulator in end-effector Cartesian space for the primitive pick-and-place task, rather than controlling joint angles and then, via direct kinematis, the end-effector position. An introduced communication delay was found to produce decrease in performance. In considerable part, this difficulty could be compensated for by preview control information. The fact that neurological control of normal human movement contains a sampled data period of 0.2 s may relate to this robustness of HO control to delay.

Stark, Lawrence↗
NASA NTRS1990

Cartesian-based control of a deformable robot manipulator

A control scheme for the 6-DOF Cincinnati-Milacron T3 robot arm is developed and demonstrated by means of numerical simulations. The arm is modeled as an open-loop articulated system with both actuators and position and velocity sensors at each joint, and a Cartesian-frame control algorithm is constructed in which (1) an adaptive scheme decouples the end-effector subsystem from the complex highly nonlinear main system and (2) a servo scheme drives the reduced system to follow a presumed end-effector trajectory on the basis of the Cartesian-frame feedback gains. The velocity transformation used to transfer the control forces from the Cartesian frame to joint-based space is explained, and the simulation results are presented in extensive graphs and diagrams. The control is found to respond well to system-topology changes and robot-environment impacts.

Chang, C. W.↗
NASA NTRS1988

Calculating Robot-Joint Coordinates From Image Coordinates

Detailed knowledge of robot joints not required. Algorithm generates approximate mathematical models of coordinates of joints of robot as functions of coordinates of points in images of work region viewed by television cameras. Joint coordinates necessary to position and orient end effector calculated by mathematical models fitted to experimentally determined data on positions, orientations, and joint coordinates. Generates models as functions of desired location of end effector of robot. Does not require priori knowledge of kinematic equations of robot.

Source record↗
NASA NTRS1994

Fault tolerant kinematic control of hyper-redundant manipulators

Hyper-redundant spatial manipulators possess fault-tolerant features because of their redundant structure. The kinematic control of these manipulators is investigated with special emphasis on fault-tolerant control. The manipulator tasks are viewed in the end-effector space while actuator commands are in joint-space, requiring an inverse kinematic algorithm to generate joint-angle commands from the end-effector ones. The rate-inverse kinematic control algorithm presented in this paper utilizes the pseudoinverse to accommodate for joint motor failures. An optimal scale factor for the robust inverse is derived.

Bedrossian, Nazareth S.↗
NASA NTRS1991

Adaptive Cartesian coordinate control of space based robot manipulators

A Cartesian coordinate robot controller is presented for use when the mass properties of a load are unknown. The mass, center of mass, and moments of inertia of the end-effector are assumed unknown. All other inertial properties of the robot are assumed known. This knowledge of the parameters allows the control of the end-effector in a way similar to the use of reaction wheels to control the orientation of a satellite. This is the primary result of the controller. The basic method of the controller is similar to that used for terrestrial-based robot manipulators. The controller is demonstrated using a new simulation algorithm which is based on Hamilton's form of the equations of motion.

Walker, Michael W.↗
NASA NTRS1990

Efficient gradient projection optimization for manipulators with multiple degrees of redundancy

An efficient gradient projection optimization scheme is presented for manipulators with multiple degrees of redundancy. This is an extension of the gradient projection scheme presented by Dubey et al. (1989) for manipulators with one degree of redundancy. The feasibility and effectiveness of this scheme are tested through simulations of the seven-degree-of-freedom NASA Laboratory Telerobotic Manipulator (LTM). Only the position of the LTM end effector is controlled, which requires only three degrees of freedom. The remaining joints, except for the wrist roll joint, which does not contribute to the end-effector linear velocity, provide three degrees of redundacy.

Zghal, H.↗
NASA NTRS1990

Improved configuration control for redundant robots

This article presents a singularity-robust task-prioritized reformulation of the configuration control scheme for redundant robot manipulators. This reformulation suppresses large joint velocities near singularities, at the expense of small task trajectory errors. This is achieved by optimally reducing the joint velocities to induce minimal errors in the task performance by modifying the task trajectories. Furthermore, the same framework provides a means for assignment of priorities between the basic task of end-effector motion and the user-defined additional task for utilizing redundancy. This allows automatic relaxation of the additional task constraints in favor of the desired end-effector motion, when both cannot be achieved exactly. The improved configuration control scheme is illustrated for a variety of additional tasks, and extensive simulation results are presented.

Seraji, H.↗