Search NASA⌕ Search

SEARCH · Search NASA

Results for “ether”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Impact of the fluorination degree of ether-based electrolyte solvents on Li-metal battery performance

Electrolytes using fluorinated solvents have proven effective in improving the cycling life of Li-metal batteries, by forming a robust solid–electrolyte interphase through decomposition of anion and fluorinated solvent molecules. Herein, we modulated the fluorination degree of ether-based electrolyte solvents to investigate their performance in Li-metal batteries. Here, we tuned the fluorination degree by installing a monofluoro substituent on one ethoxy group of 1,2-diethoxyethane (DEE) and varying the fluorination degree on the other one, providing three fluorinated DEE solvent molecules (i.e., F1F0, F1F1 and F1F2) with a relatively low fluorination degree. All three electrolytes showed improved solvation strength and ionic conductivities compared with previous highly fluorinated DEE electrolytes while retaining good oxidative stability. A full cell test using the Li-metal anode and nickel-rich cathode revealed that a higher degree of fluorination is beneficial to the cycling performance, and the cycling stability follows F1F0 < F1F1 < F1F2. Specifically, F1F0 exhibited poor cycling stability due to its instability against both the anode and cathode. While F1F1 and F1F2 both showed good stability against the Li metal anode, their relative long-term oxidative stability was responsible for the distinct performance, in which the cycle numbers at 80% capacity retention for F1F1 and F1F2 were ~20 and ~80, respectively. Finally, we demonstrated that F1F2 was able to achieve 90 cycles before reaching 80% capacity retention in practical lithium iron phosphate (LFP) pouch cells. This work shows the importance of modulating the fluorination degree of electrolyte solvents, and this approach is suitable for various cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2023

Ultra-thin ZrO 2 overcoating on CuO-ZnO-Al 2 O 3 catalyst by atomic layer deposition for improved catalytic performance of CO 2 hydrogenation to dimethyl ether

Abstract An ultra-thin overcoating of zirconium oxide (ZrO 2 ) film on CuO-ZnO-Al 2 O 3 (CZA) catalysts by atomic layer deposition (ALD) was proved to enhance the catalytic performance of CZA/HZSM-5 (H form of Zeolite Socony Mobil-5) bifunctional catalysts for hydrogenation of CO 2 to dimethyl ether (DME). Under optimal reaction conditions (i.e. 240 °C and 2.8 MPa), the yield of product DME increased from 17.22% for the bare CZA/HZSM-5 catalysts, to 18.40% for the CZA catalyst after 5 cycles of ZrO 2 ALD with HZSM-5 catalyst. All the catalysts modified by ZrO 2 ALD displayed significantly improved catalytic stability of hydrogenation of CO 2 to DME reaction, compared to that of CZA/HZSM-5 bifunctional catalysts. The loss of DME yield in 100 h of reaction was greatly mitigated from 6.20% (loss of absolute value) to 3.01% for the CZA catalyst with 20 cycles of ZrO 2 ALD overcoating. Characterizations including hydrogen temperature programmed reduction, x-ray powder diffraction, and x-ray photoelectron spectroscopy revealed that there was strong interaction between Cu active centers and ZrO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Study of Poly(ether ketone ketone) (PEKK): Outgassing Characteristics and Likely Residual Synthesis Impurities

In May-June, 2020, a study was conducted to characterize the outgassing properties of a series PEKK (Poly(ether ketone ketone)) samples using cryo-GC/MS headspace analysis. Three sets of samples were interrogated: sample group 1 consisted of 2 additively manufactured PEKK samples (PEKK "ole and "New") prepared by KCNSC from powder material from Solvay Specialty Polymers USA, LLC. Sample groups 2 and 3 consist of 5 PEKK powder types (used as feedstock for additive manufacturing processes) and 4 additively-manufactured PEKK material lots, respectively. Contrary to expectations, all samples of PEKK material were observed to outgas sulfur-containing compounds. Other analyses (EDS/EMA, GC-TOF/MS of PEKK sample extractions) confirmed the presence of sulfur in the PEKK bulk material. Specifically, Diphenyl sulfone (used as a reagent or high-temperature solvent in the synthesis of Polyaryletherketone or PAEK polymers) was observed in three of the powders and in both the PEKK "Old" and "New" samples, suggesting that the source of the sulfur can be traced to impurities in the material left over from the synthesis process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Thermal aging effects on crosslinked polyethylene cable insulation with decabromodiphenyl ether flame retardant alternative

Decabromodiphenyl ether (decaBDE) has been extensively used as a flame retardant in several applications, including nuclear electrical cable insulation. However, decaBDE has been identified as a persistent, bioaccumulative and toxic (PBT) substance, leading to regulatory scrutiny. The Environmental Protection Agency (EPA) published a regulation on January 6, 2021, aimed at phasing out the manufacturing, processing, and distribution of decaBDE. This rule set a compliance deadline of March 8, 2021, for the manufacture and processing of decaBDE, and an extended deadline of January 6, 2023, for specific applications including wire and cable insulation in nuclear power generation facilities. In response to such regulations, RSCC, a major supplier of safety-related electrical cables and associated products to the U.S. nuclear industry updated the formula of their crosslinked polyethylene (XLPE) insulation to replace the historically used decaBDE flame retardant with an acceptable alternative. This change from the previous decaBDE-containing XLPE prompted interest in comparative performance of the two material formulations, especially with respect to characteristics relevant to safety-related function such as thermal and radiation resistance. RSCC graciously provided samples of wire insulated with the decaBDE-containing XLPE formulation and corresponding wire insulated with XLPE of the new formulation, containing a decaBDE alternative. In this work we compare characteristics of the two formulations and a previously produced commercial version of the RSCC decaBDE-containing XLPE insulation subjected to thermal aging at 150 °C and 165 °C. The comparison was focused on mechanical durability, thermal stability in the oxidative environment, and chemical structures. Briefly, • Tensile elongation at break (EAB) results showed loss of mechanical elasticity with longer aging time, as expected. Aging time dependence of EAB did not differ between the decaBDE-containing and decaBDE-alternative samples. • Subtle differences between the two materials can be detected from Fourier-transform infrared spectroscopy (FTIR) absorbance spectra in the range below 1700 cm -1 , are assumed to be related to decomposition of flame retardant additives during thermal aging. • The oxidation induction time (OIT) data seemed to show that the unaged decaBDE-containing XLPE material is more thermally stable than the unaged decaBDE-alternative material, but the discrepancy in OIT decreased with aging time and the OIT values of the two materials became similar starting with the 4 th day of aging at 165 °C. This thermal aging investigation confirmed that the mechanical durability, a key property monitored for cable qualification, was not significantly affected by the modification of the formulation with a decaBDE alternative flame-retardant system in the investigated thermal aging conditions. Further studies on the same sets of materials exposed to thermal and gamma radiation aging would further inform comparison of the materials safety-related function.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Development of Crown Ether-Functionalized Polymeric Sorbents for Lithium-Ion Capture

The purpose of this Cooperative Research and Development Agreement (CRADA) was to develop and demonstrate new synthetic strategies for fabricating lithium-selective polymeric adsorbents by covalently incorporating crown ether functionalities into durable, processable support materials. These advanced sorbents are designed to selectively extract lithium ions (Li⁺) from dilute aqueous sources such as brine, seawater, industrial wastewater, and battery recycling streams.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Consideration of Decabromodiphenyl Ether Flame Retardant in Thermal and Radiation Aging of Crosslinked Polyethylene Cable Insulation

Decabromodiphenyl ether (decaBDE) has been used as a flame-retardant additive in nuclear-grade electrical cable insulation. However, decaBDE has been identified as a persistent, bioaccumulative and toxic (PBT) substance, leading to regulatory scrutiny. On January 6, 2021, the Environmental Protection Agency (EPA) published a final rule to phase out decaBDE. The 2021 rule set a two-year compliance deadline for “processing and distribution in commerce of decaBDE for use in wire and cable insulation in nuclear power generation facilities.” In recognition of industry concerns following a sudden discontinuation of decaBDE-containing Class 1E wire and cable essential for nuclear power operations and the time needed for qualifying the individual components using the alternative insulation technology, an extended compliance deadline was set in the finalized amendments to the 2021 rule as published by the Environmental Appeals Board on November 12, 2024. The 2024 rule set the compliance deadline for processing and distributing decaBDE-containing wire and cable insulation until the end of the service life of these materials. Since decaBDE has long been relied upon as the flame retardant in one of the most common cross-linked polyethylene (XLPE) nuclear cable insulation formulations, RSCC Firewall III insulation, questions have naturally arisen regarding whether changes in cable performance might be expected for XLPE containing a decaBDE alternative, especially for safety-related cables that must perform their safety function in a design basis event such as a loss of coolant accident.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

A Comparative Experimental Analysis of Natural Gas Dual Fuel Combustion Ignited by Diesel and Poly OxyMethylene Dimethyl Ether

Dual-fuel low-temperature combustion is a possible solution for alleviating the tradeoff between oxides of nitrogen and soot emissions in conventional diesel combustion, albeit with poor combustion stability, high carbon monoxide, and unburned hydrocarbon emissions at low engine loads. The present work compares emissions and combustion (heat release and other metrics) of both diesel and poly-oxy methylene dimethyl ether as high-reactivity fuels to ignite natural gas while leveraging spray-targeted reactivity stratification, which involved multiple injections of the high-reactivity fuels. The experiments included six parametric sweeps of: (1) start of first injection, (2) start of second injection, (3) percentage of energy substitution of natural gas, (4) commanded injection duration ratio, (5) rail pressure, and (6) intake pressure. The experiments were performed on a 1.8 L heavy-duty single-cylinder research engine operating at a medium speed of 1339 rev/min. Not-to-exceed limits for the indicated oxides of nitrogen emissions, maximum pressure rise rate, and the coefficient of variation of the indicated mean effective pressure were set to 1 g/kWh, 10 bar/CAD, and 10%, respectively. The indicated emissions decreased and combustion improved significantly for both fueling combinations when the experimental procedure was applied.

Partridge, Kendyl Ryan↗
DOE OSTI2020

Compatibility of Elastomers with Polyoxymethylene Dimethyl Ethers and Blends with Diesel

Polyoxymethylene dimethyl ethers (PODEs) have shown promise as candidates for diesel fuel blendstocks due to their low sooting tendency, high cetane number, and diesel-comparable boiling point range. However, there is a lack of literature regarding compatibility of PODEs with common automotive elastomers, which would be a prerequisite to their adoption into the marketplace. To address this need, an exposure study and complementary solubility analysis were undertaken. A commercially available blend of PODEs with polymerization degree ranging from 3 to 6 was blended with diesel certification fuel at 0, 33, 50, 67, at 100% by mass. Elastomer coupons were exposed to the various blends for a period of 4 weeks and evaluated for volume swell. The elastomer materials included multiple fluoroelastomers (Viton and fluorosilicone) and acrylonitrile butadiene rubbers (NBR), as well as neoprene, polyurethane, epichlorohydrin (ECO), PVC-nitrile blend (OZO), ethylene propylene diene monomer (EPDM), styrene-butadiene rubber (SBR), and silicone. The exposure results indicated overall poor compatibility for PODE, with every elastomer except for fluorosilicone exhibiting greater than 30% volume swell at the 33% blend level. The general trend across the elastomers was either a consistent increase in volume swell with PODE concentration, or maximum in volume swell at an intermediate blend fraction. One notable exception is EPDM, which is not generally compatible with diesel fuel and which exhibited a reduction in volume swell with increasing PODE concentration. The same elastomers and PODE/diesel blends were evaluated using Hansen solubility parameter analysis, which predicted similar trends to the exposure study with the exception of ECO. From these results, we conclude that adoption of PODEs as a diesel fuel blendstock will require either the development of specialized elastomers, or that the blend fraction be kept to a low level to maintain compatibility with existing elastomers.

42 ENGINEERING↗
DOE OSTI2025

Design of a High-Pressure Fuel System for Use with Dimethyl Ether

The paper documents the modeling and experimental work on a common rail fuel injection system for Dimethyl Ether, a potential diesel substitute with a low carbon intensity signature. The DME fuel system is deployed on a light duty 2.2L compression ignition engine. The paper describes the injector optimization to shift to higher flows to account for the lower heating value and density of the DME when compared to diesel. The type of the injection system used for the DME application is an advanced rendering of the Common rail noted for a one-piece piston-needle injector construction and a solenoid driven spill valve featuring a pressure balanced poppet. A dedicated high-pressure fuel pump designed to pressurize DME is used. The design results in a fast acting open and close injection event, reduced leakage, with reduced cavitation in the fuel injector volume. Design parameters for system optimization included fill and spill orifices, needle lift, bias spring, and injector hole size. The design model provides good correlation of the instantaneous rates of injection with experiments across a wide range of pressure and injection timings. Proposed performance milestones for the design included similar DME injection duration to the diesel counterpart for same fuel energy injected into the cylinder to retain high engine cycle efficiency. Here, the dedicated DME design provided reduced hydraulic delays of 50%. Tests demonstrated sustained operation at pressures of 1000 bar, with capability to reach 1500bar. Durability tests showed no cavitation-deterioration over a 200-hour test cycle by means of spray imaging and hardware inspection.

De Ojeda, William [WM International Engineering, L↗
DOE OSTI2026

Methanol mixing controlled combustion process enabled by methanol dehydration to dimethyl ether

This work demonstrates an initial proof-of-concept approach for operating a compression ignition off-road and marine relevant engine using neat methanol. The approach utilizes mixing controlled compression ignition (MCCI) of methanol that is enabled by a homogeneous charge compression ignition (HCCI) pre-burn of premixed dimethyl ether (DME). Although two fuels are used, this work explores and evaluates the opportunity and performance to generate the premixed fuel via. methanol catalytic dehydration over an alumina catalyst at engine relevant temperatures, pressures, and space velocities. Conversion purity and species output results from catalytic dehydration bench flow reactor studies were coupled with single cylinder experiments of the characterized output species for pre-burn HCCI performance. Subsequent initial methanol MCCI performance is also evaluated and compared relative to conventional diesel combustion. The detailed flow reactor results show that the catalytic dehydration conversion efficiency of methanol to DME is a function of system pressure, temperature, and space velocity. The engine results demonstrate that a 100% conversion of methanol to DME is not required for successful pre-burn HCCI, and the water formed during the dehydration process does not need to be removed to achieve the desired HCCI event from this pre-burn mixture. Subsequent methanol MCCI combustion results show that the level of methanol slip in the dehydration process affects the pre-burn HCCI phasing, low temperature heat release process, and magnitude of energy released, all of which can dictate the available window for direct injection of methanol for MCCI combustion.

Jatana, Gurneesh [ORNL] (ORCID:0000000288903225)↗
DOE OSTI2021

Dynamic polymers based on silyl ether exchange

The disclosure provides for dynamic polymers based on silyl ether exchange that are malleable and recyclable which have favorable mechanical properties and chemical resistance, methods of making thereof, and uses and applications thereof.

Guan, Zhibin↗
DOE OSTI2025

Analysis of Extracted Ingredients from Dairy Byproduct Using Dimethyl Ether

Whey permeate is a byproduct created in large quantities from the dairy industry with limited applications due to transportation and stability. Whey permeate is primarily comprised of water, carbohydrates, and minerals with minimal contribution of proteins. Various biomasses in food processing have utilized liquid dimethyl ether (DME) as a form of extraction for high-value ingredients and dewatering. DME is a growing interest in wastewater and biomass treatment due to it being a green solvent, ability to dissolve organic solvents, and miscibility with water. The current study is to determine if DME can effectively dewater whey permeate as well as recover components that can be further used in the food industry as a value-added ingredient. Analysis of the liquid extract and solid extract was evaluated with inductively coupled plasma-mass spectrometry (ICP-MS) and solid extracts were further characterized with the application of a scanning electron microscope (SEM).

09 - BIOMASS FUELS↗
DOE OSTI2026

Methanol mixing−controlled compression ignition enabled via homogeneous charge compression ignition of dimethyl ether through catalytic decomposition of methanol

Methanol is a potentially attractive fuel for marine and off−road engines owing to its availability at bunkering and global distribution locations. Although methanol is well−distributed worldwide, its fuel chemistry and ignition properties make it poorly suited as a direct drop−in replacement for diesel fuel in compression−ignition engines. However, industrial processes are regularly used to convert methanol, via catalytic dehydration, to dimethyl ether (DME) over nonprecious metal catalysts. This chemical conversion can occur at relatively low pressures, temperatures, and catalyst space velocities, highlighting a potential opportunity to generate DME via onboard catalytic dehydration of methanol. DME’s fuel kinetic and ignition properties for compression ignition are much more favorable than those of methanol or even diesel fuel, but DME is more challenging than diesel fuel or methanol to pump, store, and deliver through conventional diesel fueling injection hardware. Thus, a potential opportunity exists to use the ignition and kinetic properties of DME, with the transportation and delivery advantages of methanol, in a methanol−fueled mixing−controlled compression−ignition engine. The present work explores performance, combustion behavior, and emissions reduction opportunities for methanol mixing−controlled combustion, enabled by a HCCI of DME that represents a small fraction of the total fuel energy that can be generated onboard via catalytic dehydration of methanol.

Splitter, Derek [ORNL] (ORCID:0000000174044047)↗
DOE OSTI2020

Nucleophilic Thiols Reductively Cleave Ether Linkages in Lignin Model Polymers and Lignin

Lignin may serve as a renewable feedstock for the production of chemicals and fuels if mild, scalable processes for its depolymerization can be devised. The use of small organic thiols represents a bioinspired strategy to cleave the β–O–4 bond, the most common linkage in lignin. In the present study, synthetic β–O–4 linked polymers were treated with organic thiols, yielding up to 90 % cleaved monomer products. Lignin extracted from poplar was also treated with organic thiols resulting in molecular weight reductions as high as 65 % (Mn) in oxidized lignin. Thiol–based cleavage of other lignin linkages was also explored in small–molecule model systems to uncover additional potential pathways by which thiols might depolymerize lignin. The success of thiol–mediated cleavage on model dimers, polymers, and biomass–derived lignin illustrates the potential utility of small redox–active molecules to penetrate complex polymer matrices for depolymerization and subsequent valorization of lignin into fuels and chemicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗