Search NASA⌕ Search

SEARCH · Search NASA

Results for “extreme deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Cyclic loading–unloading impacts on geomechanical stability of multiple salt caverns for underground hydrogen storage

Underground caverns in a salt dome are promising geologic features to store hydrogen because of salt’s extremely low permeability and self-healing behavior. The salt cavern storage community, however, has not fully understood the geomechanical behaviors of salt rock driven by quick operation cycles of injection–production, which may significantly impact the cost-effective storage-recovery performance of multiple caverns. Our field-scale generic model captures the impact of cyclic loading–unloading on the salt creep behavior and deformation under different cycle frequencies, operating pressure, and spatial order of operating cavern(s). This systematic simulation study indicates that the initial operation cycle and arrangement of multiple caverns play a significant role in the creep-driven loss of cavern volumes and cavern deformation. Finally, our future study will develop a new salt constitutive model based on geomechanical tests of site-specific salt rock to probe the cyclic behaviors of salt precisely both beneath and above the dilatancy boundary, including reverse (inverse transient) creep, the Bauschinger effect, and damage-healing mechanism.

08 HYDROGEN↗
DOE OSTI2023

Dislocation generation in diamond under extreme loading

Diamond is, by virtue of its high bonding forces and Peierls-Nabarro barrier stresses, among the hardest materials on earth due to the difficulty of generating and moving dislocations. We demonstrate, using molecular dynamics and analytical calculations, that the generation of defects is dependent on loading orientation. Shock-loading single-crystal diamond along [001] and [011] to a stress of 137 GPa did not reveal dislocations, whereas loading along [111] generated profuse dislocations. The introduction of a void at the latter orientation generated dislocations at 72.6 GPa. Two slip systems were identified: <011>{100} and <112>{111}. The threshold for plastic deformation in diamond is orientation dependent and significantly lower than reported in previous studies: 0.14 G (shear modulus). The void collapse generated localized amorphization for [001]. In conclusion, these results on the anisotropy of plasticity and void effects have relevance for the improvement of symmetry in the collapse of diamond capsules in inertial fusion experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Impacts on mechanical strength of chemical reactions induced by hydrous supercritical CO2 in Boise Sandstone

Geomechanics experiments were used to assess mechanical alteration of Boise Sandstone promoted by reactions with supercritical carbon dioxide (scCO 2 ) and water vapor. During geologic carbon storage, scCO 2 is injected into subsurface reservoirs, forming buoyant plumes. At brine-plume interfaces, scCO 2 can dissolve into native brines, and water from brines can partition into scCO 2 , forming hydrous scCO 2 . This study investigates the effect of hydrous scCO 2 on the strength of Boise Sandstone. Samples are first exposed to recirculating hydrous scCO 2 for 24 h at 70 °C and 13.8 MPa scCO 2 pressure. Samples are reacted with scCO 2 with added water contents up to 500 mL. After scCO 2 exposure, samples are deformed at room temperature under confining pressures of 3.4, 6.9, and 10.3 MPa. The results demonstrate that hydrous scCO 2 induces chemical reactions in Boise Sandstone, with ions migrating from the solid into the hydrous scCO 2 phase. At the longer time-scales, these reactions could lead to mechanical weakening in the samples; however, on the scale of our experiments, the strength changes are within sample variability. Because the solubility of water in scCO 2 is extremely low (0.008 mol H 2 O per 1 mol CO 2 ), the mineral dissolution of Boise Sandstone was under 0.002 wt.%. Additionally, mineral grains and pore throats in Boise Sandstone are cemented with quartz, which is not susceptible to dissolution at these conditions. Our results indicate that humidity in scCO 2 plumes is unlikely to sustain chemical reactions and induce long term strength changes in quartz cemented sandstones due to resistant mineralogies and low water solubility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Towards the Ultimate Strength of Medium‐Entropy Alloys Through Pulsed Lasers

The tensile strength of metals at extreme strain rates is a key predictor of their performance in ballistic and structural impact applications. An important experimental method to reach these extreme strain rates is the use of high-amplitude, short-duration pulsed lasers. The Jupiter Laser Facility at the Lawrence Livermore National Laboratory enabled probing for the first time the mechanical response of several promising High Entropy Alloys at times on the order of nanoseconds (strain rates of ∼10 7 and ∼10 9 s −1 ). The measured strength is in the range of 6 to 10 GPa, ten times the quasistatic value. The mechanisms of plastic deformation and failure were identified and quantified through analysis and molecular dynamics simulation. The reflected wave amplitudes, obtained by VISAR, were used to determine the tensile (spall) stress. The high tensile strength obtained is due to two factors: the strain-rate dependence of plastic flow and the kinetics of void nucleation, growth, and coalescence. The experimental results are compared with an analytical prediction considering both grain-interior and grain-boundary void initiation. Molecular dynamics simulations, conducted at strain rates of 10 8 and 10 9 s −1 , rationalize the experimental results. In conclusion, they provide valuable information about the process of failure evolution, and reveal that grain boundary separation plays a pivotal role in spalling.

Materials science↗
DOE OSTI2025

SEM/EBSD Characterization of Baffle-Former Bolts Designated for High Energy X-ray Microscopy Studies at the Advanced Photon Source

This report documents the microstructural and surface characterization of two high-fluence baffle-former bolts (BFBs) harvested from a commercial pressurized water reactor (PWR) after nearly four decades of service. These bolts experienced extreme conditions including high neutron fluence, elevated temperatures, corrosive primary water, and sustained mechanical loads, all of which contribute to degradation mechanisms such as irradiation-assisted stress corrosion cracking (IASCC). Using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), the study assessed bulk and near-surface microstructures, grain boundary characteristics, and in-service oxide layers. The results revealed significant differences between bolts exposed to 41 dpa and 29 dpa, including differences in recrystallization extent, deformation structures, and oxidation morphology. These findings establish critical baseline data for integration with advanced synchrotron-based high-energy X-ray microscopy (HEXM) and computational crystal plasticity models. Ultimately, the work supports improved mechanistic understanding and predictive capability regarding the long-term performance of reactor core internal components.

Lach, Tim [Oak Ridge National Laboratory (ORNL), O↗
DOE OSTI2020

An Accelerated Creep Testing Program For Nickel Based Superalloys

In order to improve the energy production within the United States, new materials are developed with the goal of increased functionality. These materials are required to perform at extreme pressures and temperatures (up to and beyond 200MPa and 650â??) as well as be sustainable beyond 105 hours. Before developing these materials into components for power generation, mechanical testing is required to better understand the behavior of these materials at various loads and temperatures. The longest of these tests is the conventional creep test which is a real time test that can beyond 105 hours depending on service conditions. Hundreds of specimens must be tested before being approved for use in power generation, but it is extremely difficult to rapidly qualify when each material is required to exceed 105 hours making testing through conventional means unfeasible. While others have designed accelerated testing methods to help qualify materials, many of these experiments use an empirical approach that requires test data to fit already existing creep data. In this study, an accelerated creep test called the stepped isostress method (SSM) is then applied to wrought Inconel 718 (IN 718) specimens. A test matrix is designed using deformation mechanism maps, time-temperature-transformation diagrams, and time-temperature-precipitation diagrams, in order to ensure that microstructurally, the accelerated creep tests fail similarly to the conventional creep tests. The data from the stepped isostress method is then applied to the McVetty and Sin-hyperbolic (Sinh) constitutive models in order to generate a creep master curve. The results from the model fits are then compared to the conventional creep data done from experiments as well as from the NIMS database for Inconel 718. Optical microscopy and scanning electron microscopy are used to compare the evolution of the microstructure from the conventional creep and accelerated creep tests. It is found that using the Sinh model on the accelerated creep data provides reasonable creep rupture predictions when compared to the scatter band of creep tests. It was also observed that the microstructural evolution between the SSM experiments and creep tests were very similar in terms of the volume fraction of precipitates and phases.

Mach, Robert↗
DOE OSTI2024

Kink bands promote exceptional fracture resistance in a NbTaTiHf refractory medium-entropy alloy

Single-phase body-centered cubic (bcc) refractory medium- or high-entropy alloys can retain compressive strength at elevated temperatures but suffer from extremely low tensile ductility and fracture toughness. We examined the strength and fracture toughness of a bcc refractory alloy, NbTaTiHf, from 77 to 1473 kelvin. This alloy’s behavior differed from that of comparable systems by having fracture toughness over 253 MPa·m 1/2 , which we attribute to a dynamic competition between screw and edge dislocations in controlling the plasticity at a crack tip. Whereas the glide and intersection of screw and mixed dislocations promotes strain hardening controlling uniform deformation, the coordinated slip of <111> edge dislocations with {110} and {112} glide planes prolongs nonuniform strain through formation of kink bands. These bands suppress strain hardening by reorienting microscale bands of the crystal along directions of higher resolved shear stress and continually nucleate to accommodate localized strain and distribute damage away from a crack tip.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A new approach to the evaluation and solution of the relativistic kinetic dispersion relation and verification with continuum kinetic simulation

Here, the present work describes a new approach to evaluation and root finding for the kinetic dispersion relation of Langmuir waves, which is central to the analytical understanding of collisionless damping in plasmas. The plasma dispersion function is solved to machine precision using direct integration in the complex plane in combination with an analytic evaluation of the residue to account for the deformation along the Landau contour. To efficiently attain machine precision, the contour is displaced in the complex plane prior to integration, and numerical subtleties related to the placement of the contour are discussed. The approach is generic in that it applies to arbitrary distribution functions, with the present manuscript focused on relativistic cases. Detailed verification of results via direct kinetic simulation in a variety of configuration space dimensions is also presented. Finally, the technique is applied to the challenging case of highly relativistic (i.e. extremely hot) plasmas. Here we show both qualitative agreement with prior work, as well as the disappearance of the Landau root which would have significant implication for real-life observation or experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Thermoplasticity of metallic glasses: Processing and applications

Owing to their extremely low shear viscosity and fragility, bulk metallic glasses (BMGs) are envisioned as new net-shaping material replacing conventionally used crystalline metals for various applications. The first part of this review describes the general technique and kinetics of thermoplastic forming. The second part elaborates on the thermal processing capability of metallic glasses from atomic- to meter-scale. The micro-/nano-structure obtained after various quenching rates followed by temperature, time and heating rate dependent thermoplastic forming is described in the third section. The deformation behavior and flow kinetics of BMGs in terms of composition, mold features, and applied conditions are elaborated in the fourth section. The variation of volume and enthalpy at the supercooled liquid region, strength retention of metallic glasses compared to other conventional metals and alloys, and kinetics of liquid fragility are given in the fifth section. Finite element modeling and molecular dynamics simulations of high-temperature deformation in BMGs are presented in the sixth part. Finally, thermally-formed BMGs used for different applications, including energy, biomedical and micro-optics, are presented in the final part. Altogether, this review provides an overview of shaping capabilities and modifications in the macro-scale properties and short-to-medium range order of BMGs upon thermoplastic forming.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Evidence of non-isentropic release from high residual temperatures in shocked metals measured with ultrafast x-ray diffraction

Shock experiments are widely used to understand the mechanical and electronic properties of matter under extreme conditions. However, after shock loading to a Hugoniot state, a clear description of the post-shock thermal state and its impacts on materials is still lacking. We used diffraction patterns from 100-fs x-ray pulses to investigate the temperature evolution of laser-shocked Al–Zr metal film composites at time delays ranging from 5 to 75 ns driven by a 120-ps short-pulse laser. We found significant heating of both Al and Zr after shock release, which can be attributed to heat generated by inelastic deformation. A conventional hydrodynamic model that employs (i) typical descriptions of Al and Zr mechanical strength and (ii) elevated strength responses (which might be attributed to an unknown strain rate dependence) did not fully account for the measured temperature increase, which suggests that other strength-related mechanisms (such as fine-scale void growth) could play an important role in thermal responses under shock wave loading/unloading cycles. Our results suggest that a significant portion of the total shock energy delivered by lasers becomes heat due to defect-facilitated plastic work, leaving less converted to kinetic energy. This heating effect may be common in laser-shocked experiments but has not been well acknowledged. High post-shock temperatures may induce phase transformation of materials during shock release. Another implication for the study is the preservability of magnetic records from planetary surfaces that have a shock history from frequent impact events.

42 ENGINEERING↗
DOE OSTI2020

Mechanistic basis of oxygen sensitivity in titanium

One of the most potent examples of interstitial solute strengthening in metal alloys is the extreme sensitivity of titanium to small amounts of oxygen. Unfortunately, these small amounts of oxygen also lead to a markedly decreased ductility, which in turn drives the increased cost to purify titanium to avoid this oxygen poisoning effect. Here, we report a systematic study on the oxygen sensitivity of titanium that provides a clear mechanistic view of how oxygen impurities affect the mechanical properties of titanium. The increased slip planarity of Ti-O alloys is caused by an interstitial shuffling mechanism, which is sensitive to temperature, strain rate, and oxygen content and leads to the subsequent alteration of deformation twinning behavior. The insights from our experimental and computational work provide a rationale for the design of titanium alloys with increased tolerance to variations in interstitial content, with notable implications for more widespread use of titanium alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Extreme matter meets extreme gravity: Ultraheavy neutron stars with phase transitions

The speed of sound of the matter within neutron stars may contain nonsmooth structure related to first- or higher-order phase transitions. Here we investigate what are the observable consequences of structure in the speed of sound, such as bumps, spikes, step functions, plateaus, and kinks. One of the main consequences is the possibility of ultraheavy neutron stars (with masses larger than 2.5 solar masses), mass twins in heavy (with masses larger than 2 solar masses) and ultraheavy neutron stars. These stars pass all observational and theoretical constraints, including those imposed by recent LIGO/Virgo gravitational-wave observations and NICER x-ray observations. Here we thoroughly investigate other consequences of this structure in the speed of sound to develop an understanding of how nonsmooth features affect astrophysical observables, such as stellar radii, tidal deformability, moment of inertia, and Love number. Our results have important implications for future gravitational wave and x-ray observations of neutron stars and their impact in nuclear astrophysics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

New Nonreactive Force Field for Accurate Molecular Dynamics Simulations of TATB at Extreme Conditions

Insensitive high explosives based on TATB (1,3,5-triamino-2,4,6-trinitrobenzene) are needed in applications when safety is of paramount importance, but the basic material properties that give rise to its insensitivity are not fully understood. Molecular dynamics modeling using empirical force fields (FFs) has been the main route to characterize many complicated dynamical properties of TATB single crystal, but these FFs have not been comprehensively tested at extreme conditions typical of detonation. We collect a benchmark data set of (quasi)static TATB physical properties as determined by experiments and electronic structure calculations and apply this data set to validate four existing TATB FFs along with a new TATB FF that we develop here and denote as the CEA-LLNL-Missouri (CLM) FF. Benchmark data include vibrational spectra, the TATB crystal temperature–pressure–volume equation of state and lattice parameters, properties of TATB crystal polymorphs and transitions to the gaseous and liquid states, dimer energy landscapes, the pressure-dependent elastic tensor, and the energy landscape for inelastic deformation via sliding of TATB crystal layers. As a general assessment, we find that the two existing nonreactive FFs are more accurate in describing TATB’s physical properties compared to the two variants of the ReaxFF reactive FF considered. The new CLM FF is found to consistently yield similar or better agreement with experiments and electronic structure theory than any of the existing FF models, and it presents a distinct improvement in accurately modeling TATB elasticity and equation of state. So this work is expected to help improve the accuracy of FF-based modeling of complicated dynamic responses that ultimately govern the safety and performance characteristics of this material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Large-Scale Welding Process Simulation by GPU Parallelized Computing

The computational design of industrially relevant welded structures is extremely time consuming due to coupled physics and high nonlinearity. Previously, most welding distortion and residual stress simulations have been limited to small coupons and reduced order (from three-dimensional [3D] to two-dimensional [2D]), or inherent strain approximations were used for large structures. In this current study, an explicit finite element code based on a graphics processing unit was utilized to perform 3D transient thermomechanical simulation of structural components during welding. Laser brazing of aluminum alloy panels as representative of automotive manufacturing scenarios was simulated to predict out-of-plane distortion under different clamping conditions. The predicted deformation pattern and magnitude were validated by laser scanning data of physical assemblies. In addition, the code was used to investigate residual stresses developed during multipass arc welding of a nuclear industry pressurizer surge nozzle and subsequent welding repair where a 3D simulation was necessary. Taking the experimental data as reference, the 3D model predicted better residual stress distribution than a typical 2D asymmetrical model. Stress evolution in welding repair was also presented and discussed in this study. Furthermore, the efficient numerical model made it feasible to use integrated computational welding engineering to simulate welding processes for large-scale structures.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Kinetics of HCP-BCC Phase Transition Boundary in Magnesium at High Pressure

Under high pressures, many crystalline metals undergo solid–solid phase transformations. In order to accurately model the behavior of materials under extreme loading conditions, it is essential to understand the kinetics of phase transition. Using molecular dynamics simulations, this work demonstrates the feasibility of characterizing the speeds of a moving phase boundary using atomistic simulations employing a suitable empirical potential for single-crystal magnesium. The model can provide temperature- and tensorial stress-dependent velocity of a moving phase boundary as a rate-limiting contribution to the kinetics of phase transformation in continuum codes. Results demonstrate that a nonlinear interaction exists between plasticity and phase transition, facilitating a jump in the velocity of a moving phase boundary, facilitated by activated plastic deformation mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Statistical evaluation of microscale stress conditions leading to void nucleation in the weak shock regime

Here, we investigate the heterogeneity of the stress state driven by anisotropic deformation response at the single crystal level through five statistical volume element (SVE) calculations of polycrystalline BCC tantalum. This work focuses on grain boundaries as a prominent material defect type prone to void nucleation based upon experimental observations of predominantly intergranular void nucleation in this material. The SVEs are constructed to be statistically representative of larger volumes of material and are meshed such that mean and standard deviation of grain size and orientation information is reconstructed. The computational meshes feature hexahedral (brick) elements and smooth conformal grain boundaries where significant stress concentration is known to occur, a tail effect of interest in the extreme events process of dynamic ductile damage. An existing micromechanical crystallographic plasticity model shown to capture the single crystal behavior of BCC tantalum well is used to perform the polycrystal calculations. The model includes representation of the non-Schmid effect of non-planar screw dislocation kinetics in tantalum. A three-dimensional stress state time profile predicted by damage modeling of a flyer plate impact experiment is applied as boundary conditions to each SVE. Resulting grain boundary stress state statistics are strongly non-Gaussian. Significant structural evolution is observed within the compressive hold before unloading into tension in the stress profile. Strong angular dependence of grain boundary traction magnitude with shock direction is observed. Non-Schmid effects continue to suggest their influence on propensity of microstructural defect types to nucleate voids. A general void nucleation criterion is proposed using probability theory. The general framework is specified to polycrystalline BCC tantalum in the weak shock regime to include the SVE calculations and literature molecular dynamics calculations of grain boundary void nucleation strength. Probability density functions (PDFs) are used to describe the interaction between the local stress state heterogeneity and the distributed grain boundary void nucleation strength state. A causation entropy maximization procedure removes the requirement for ad hoc selection of a PDF functional form and provides a rigorous procedure for data-based PDF determination. The resulting physically informed PDF describes the spatial appearance frequency of nucleated voids as a function of applied macroscale pressure. Lower length scale physics are thus packaged in a precise and computationally efficient way to provide computational plasticity insight to macroscale dynamic ductile damage models.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quasi-static to Dynamic Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) has a need to understand the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys made by conventional wrought processing and additive manufacturing (AM). This two-year work scope will be performed at the Colorado School of Mines (Mines) and will include quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with high strain rate (Kolsky) pressure bar testing in tension and compression (e.g., 10 3 s -1 ), without and with temperature variations. Gas gun experiments at higher strain rates (e.g., over 10 3 s -1 ) will also be pursued. Complementary microstructure characterization will be performed on undeformed and deformed samples to fundamentally understand the role of processing on the microstructure characteristics and resulting deformation mechanisms that dictate the mechanical response of these alloys with variations in strain rate, temperature, and strain state. Alloys of interest will be Ta-based, containing up to 10 wt.% W. LLNL will supply initial wrought-processed material for sample machining. LLNL will also supply samples built by AM during the project for testing. Arc melting and casting may also be performed at Mines to produce small quantities of different alloys for machining and exploratory testing on an as-needed basis. This project will support multiple postdocs and graduate students at Mines, training them with the knowledge, skills, and abilities needed to study materials under extreme conditions of interest to the National Nuclear Security Agency.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The mechanism of twin thickening and the elastic strain state of TWIP steel nanotwins

A Twinning Induced Plasticity (TWIP) steel with a nominal composition of Fe-16.4Mn-0.9C-0.5Si-0.05Nb-0.05V was deformed to an engineering strain of 6%. The strain around the deformation twins were mapped using the 4D-STEM technique. Strain mapping showed a large average elastic strain of approximately 6% in the directions parallel and perpendicular to the twinning direction. However, the large average strain comprised of several hot spots of even larger strains of up to 12%. These hot spots could be attributed to a high density of sessile Frank dislocations on the twin boundary and correspond to shear stresses of 1–1.5 GPa. The strain and therefore stress fields are significantly larger than other materials known to twin and are speculated to be responsible for the early thickness saturation of TWIP steel nanotwins. The ability to keep twins extremely thin helps improve grain fragmentation, i.e. the dynamic Hall–Petch effect, and underpins the large elongations and strain hardening rates in TWIP steels.

36 MATERIALS SCIENCE↗