SEARCH · Search NASA

Results for “fixed boundaries”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Primer vector theory applied to the linear relative-motion equations

Prime vector theory is used in analyzing a set of linear relative-motion equations - the Clohessy-Wiltshire (C/W) equations - to determine the criteria and necessary conditions for an optimal N-impulse trajectory. The analysis develops the analytical criteria for improving a solution by: (1) moving any dependent or independent variable in the initial and/or final orbit, and (2) adding intermediate impulses. If these criteria are violated, the theory establishes a sufficient number of analytical equations. The subsequent satisfaction of these equations will result in the optimal position vectors and times of an N-impulse trajectory. The solution is examined for the specific boundary conditions of: (1) fixed-end conditions, two impulse, and time-open transfer; (2) an orbit-to-orbit transfer; and (3) a generalized renezvous problem.

Jezewski, D.↗

NASA NTRS1983

Finite-element methods for steady solidification problems

Four Galerkin finite-element methods are tested for solving the free-boundary problem that describes steady solidification. The formulations differ in the solution method used to account for the unknown shape of the melt/solid interface, in the interphase condition (either balance of heat flux or equilibrium of temperature) distinguished for locating the interface, and in the technique used for solving the systems of algebraic equations that result from the finite-element approximations. Methods that use the melting point isotherm to locate the melt/solid interface are found more accurate and efficient than formulations based on the interfacial energy balance. Solution by a Galerkin-Newton algorithm of the free-boundary problem transformed to a fixed domain is most efficient when the field problem in each phase is made nonlinear by including radiation from the melt and solid to the surroundings.

Ettouney, H. M.↗

NASA NTRS1984

Natural laminar flow experiments on modern airplane surfaces

Flight and wind-tunnel natural laminar flow experiments have been conducted on various lifting and nonlifting surfaces of several airplanes at unit Reynolds numbers between 0.63 x 10 to the 6th power/ft and 3.08 x 10 to the 6th power/ft, at Mach numbers from 0.1 to 0.7, and at lifting surface leading-edge sweep angles from 0 deg to 63 deg. The airplanes tested were selected to provide relatively stiff skin conditions, free from significant roughness and waviness, on smooth modern production-type airframes. The observed transition locations typically occurred downstream of the measured or calculated pressure peak locations for the test conditions involved. No discernible effects on transition due to surface waviness were observed on any of the surfaces tested. None of the measured heights of surface waviness exceeded the empirically predicted allowable surface waviness. Experimental results consistent with spanwise contamination criteria were observed. Large changes in flight-measured performance and stability and control resulted from loss of laminar flow by forced transition. Rain effects on the laminar boundary layer caused stick-fixed nose-down pitch-trim changes in two of the airplanes tested. No effect on transition was observed for flight through low-altitude liquid-phase clouds. These observations indicate the importance of fixed-transition tests as a standard flight testing procedure for modern smooth airframes.

Holmes, B. J.↗

NASA NTRS1993

Aspects of a high-resolution scheme for the Navier-Stokes equations

In this paper we emphasize the importance of the form of the numerical dissipation model in computing accurate viscous flow solutions. A high-resolution scheme for viscous flows based on three-point central differencing and a matrix dissipation is considered. The various components of this scheme, including 'entropy fix', limiter function, and boundary-point dissipation are discussed. By analyzing boundary-point dissipation stencils, we confirm that with the matrix dissipation model the normal numerical dissipation terms in the streamwise momentum equation are independent of the Reynolds number. Such independence is not achieved with a scalar dissipation form. The accuracy of the central-difference scheme, with and without matrix dissipation, and the flux-difference split scheme of Roe, which is classified as a high-resolution scheme, is compared. For this comparison, three high Reynolds number laminar flows are considered. Solutions of the Navier-Stokes equations are obtained for low-speed flow over a flat plate, transonic flow over an airfoil with transition near the leading edge, and hypersonic flow over a compression ramp. The emphasis of the comparison is primarily on the details of the viscous flows. The necessity of the high-resolution property is revealed.

Swanson, R. C.↗

NASA NTRS1959

Some Basic Aspects of Magnetohydrodynamic Boundary-Layer Flows

An appraisal is made of existing solutions of magnetohydrodynamic boundary-layer equations for stagnation flow and flat-plate flow, and some new solutions are given. Since an exact solution of the equations of magnetohydrodynamics requires complicated simultaneous treatment of the equations of fluid flow and of electromagnetism, certain simplifying assumptions are generally introduced. The full implications of these assumptions have not been brought out properly in several recent papers. It is shown in the present report that for the particular law of deformation which the magnetic lines are assumed to follow in these papers a magnet situated inside the missile nose would not be able to take up any drag forces; to do so it would have to be placed in the flow away from the nose. It is also shown that for the assumption that potential flow is maintained outside the boundary layer, the deformation of the magnetic lines is restricted to small values. The literature contains serious disagreements with regard to reductions in heat-transfer rates due to magnetic action at the nose of a missile, and these disagreements are shown to be mainly due to different interpretations of reentry conditions rather than more complicated effects. In the present paper the magnetohydrodynamic boundary-layer equation is also expressed in a simple form that is especially convenient for physical interpretation. This is done by adapting methods to magnetic forces which in the past have been used for forces due to gravitational or centrifugal action. The simplified approach is used to develop some new solutions of boundary-layer flow and to reinterpret certain solutions existing in the literature. An asymptotic boundary-layer solution representing a fixed velocity profile and shear is found. Special emphasis is put on estimating skin friction and heat-transfer rates.

Hess, Robert V.↗

DOE OSTI2024

A gyrokinetic simulation model for 2D equilibrium potential in the scrape-off layer of a field-reversed configuration

The equilibrium potential structure in the scrape-off layer (SOL) of the field-reversed configuration (FRC) can be affected by the penetration of edge biasing applied at the divertor ends. The primary focus of the paper is to establish a formulation that accurately captures both parallel and radial variations of the two-dimensional (2D) potential in SOL. The formulation mainly describes a quasi-neutral plasma with a logical sheath boundary. A full-f gyrokinetic ion model and a massless electron model are implemented in the GTC-X code to solve for the self-consistent equilibrium potential, given fixed radial potential profiles at the boundaries. The first essential point of this 2D model lies in its ability to couple radial and parallel dynamics stemming from resistive currents and drag force on ions. The model successfully recovers the fluid force balance and continuity equations. These collisional effects on 2D potential mainly appear through the density profile changes, modifying the potential through electron pressure gradient. This means an accurate prescription of electron density and temperature profiles is important in predicting the potential structure in the FRC SOL. The Debye sheath potential and the potential profiles applied at the boundaries can be additional factors contributing to the 2D variations in SOL. This comprehensive full-f scheme holds promise for future investigations into turbulent transport in the presence of the self-consistent 2D potential together with the non-Maxwellian distributions and open boundary conditions in the FRC SOL.

Physics↗

NASA NTRS1976

Comparison of solutions to boundary-layer and Navier-Stokes equations for the case of mass removal from a turbulent boundary layer

Comparisons are made over a range of Mach numbers from 1.5 to 7.5 at a fixed Reynolds number for various amounts of mass removal (boundary-layer bleed). Results indicate that boundary-layer theory can be used for design purposes in the range of bleed rates required to eliminate separation in an isolated, strong, adverse pressure gradient. Only about 5% to 10% of the boundary-layer mass flow must be removed to prevent such separations. Direct comparisons of bleed rates required to eliminate separation predicted by boundary-layer and Navier-Stokes equations for an M = 3.5-engine inlet centerbody show comparable results.

Rose, W. C.↗

NASA NTRS1992

The multiple-function multi-input/multi-output digital controller system for the AFW wind-tunnel model

A real time multiple-function digital controller system was developed for the Active Flexible Wing (AFW) Program. The digital controller system (DCS) allowed simultaneous execution of two control laws: flutter suppression and either roll trim or a rolling maneuver load control. The DCS operated within, but independently of, a slower host operating system environment, at regulated speeds up to 200 Hz. It also coordinated the acquisition, storage, and transfer of data for near real time controller performance evaluation and both open- and closed-loop plant estimation. It synchronized the operation of four different processing units, allowing flexibility in the number, form, functionality, and order of control laws, and variability in the selection of the sensors and actuators employed. Most importantly, the DCS allowed for the successful demonstration of active flutter suppression to conditions approximately 26 percent (in dynamic pressure) above the open-loop boundary in cases when the model was fixed in roll and up to 23 percent when it was free to roll. Aggressive roll maneuvers with load control were achieved above the flutter boundary. The purpose here is to present the development, validation, and wind tunnel testing of this multiple-function digital controller system.

Hoadley, Sherwood T.↗

NASA NTRS1992

The multiple-function multi-input/multi-output digital controller system for the AFW wind tunnel model

A real-time multiple-function digital controller system was developed for the Active Flexible Wing (AFW) Program. The digital controller system (DCS) allowed simultaneous execution of two control laws: flutter suppression and either roll trim or a rolling maneuver load control. The DCS operated within, but independently of, a slower host operating system environment, at regulated speeds up to 200 Hz. It also coordinated the acquisition, storage, and transfer of data for near real-time controller performance evaluation and both open- and closed-loop plant estimation. It synchronized the operation of four different processing units, allowing flexibility in the number, form, functionality, and order of control laws, and variability in selection of sensors and actuators employed. Most importantly, the DCS allowed for the successful demonstration of active flutter suppression to conditions approximately 26 percent (in dynamic pressure) above the open-loop boundary in cases when the model was fixed in roll and up to 23 percent when it was free to roll. Aggressive roll maneuvers with load control were achieved above the flutter boundary.

Hoadley, Sherwood T.↗

NASA NTRS1966

Calculated blade response at high tip-speed ratios

This paper presents the initial results of a digital computer study of helicopter rotor-blade-motion stability for a broad range of forward speeds encompassing proposed conventional and compound helicopter designs. The analysis treats the general case of nonlinear, coupled flapping and lagging motions of hinged rigid blades. The results of the study to date indicate that blade-motion stability boundaries cannot be specified for a given blade design in terms of a fixed value of rotor tip-speed ratio. The stability boundaries can shift significantly within the desired operational speed range, with the stability limits depending upon the rotor loading, the magnitude of the disturbance encountered by the blade, and the blade position at the instant the external disturbance is encountered. The sample methods suggested for improving blade-motion stability include increasing the effective hinge spring restraint by incorporating pitch-flap coupling or by using hingeless or teetering rotor systems. Reducing rotor loading also has a beneficial effect on the blade-motion stability. The results indicate that methods used to deal with the blade-motion stability problem can be expected to diminish the overall vibration levels of the helicopter rotor system across the entire design speed range.

TIP SPEED↗

NASA NTRS1972

Characteristics of the unsteady shock-induced laminar boundary layer on a flat plate.

The unsteady shock-induced laminar boundary layer on a flat plate is theoretically studied for shock speeds ranging from 1.12 to 9 km/sec. Boundary layer flows for real air, assumed to be in thermochemical equilibrium, are analyzed by extending Lam's work on shock-induced laminar boundary layers to equilibrium dissociated and ionized flows. A complete description of the unsteady nature of the boundary layer is presented in terms of heat transfer and several boundary layer thickness quantities as functions of a single time-position variable. Boundary layer development is considered for two points of view. Time-dependent boundary layer development and approach to steady state for any fixed position on the plate is described, as is the configuration of the boundary layer with position on the plate at any point in time.

Cook, W. J.↗

NASA NTRS2001

Global Discrete Artificial Boundary Conditions for Time-Dependent Wave Propagation

We construct global artificial boundary conditions (ABCs) for the numerical simulation of wave processes on unbounded domains using a special non-deteriorating algorithm that has been developed previously for the long-term computation of wave-radiation solutions. The ABCs are obtained directly for the discrete formulation of the problem; in so doing, neither a rational approximation of 'non-reflecting kernels,' nor discretization of the continuous boundary conditions is required. The extent of temporal nonlocality of the new ABCs appears fixed and limited; in addition, the ABCs can handle artificial boundaries of irregular shape on regular grids with no fitting/adaptation needed and no accuracy loss induced. The non-deteriorating algorithm, which is the core of the new ABCs is inherently three-dimensional, it guarantees temporally uniform grid convergence of the solution driven by a continuously operating source on arbitrarily long time intervals, and provides unimprovable linear computational complexity with respect to the grid dimension. The algorithm is based on the presence of lacunae, i.e., aft fronts of the waves, in wave-type solutions in odd-dimension spaces, It can, in fact, be built as a modification on top of any consistent and stable finite-difference scheme, making its grid convergence uniform in time and at the same time keeping the rate of convergence the same as that of the non-modified scheme. In the paper, we delineate the construction of the global lacunae-based ABCs in the framework of a discretized wave equation. The ABCs are obtained for the most general formulation of the problem that involves radiation of waves by moving sources (e.g., radiation of acoustic waves by a maneuvering aircraft). We also present systematic numerical results that corroborate the theoretical design properties of the ABCs' algorithm.

Ryabenkii, V. S.↗

NASA NTRS1988

Formation of the wave compressional boundary in the earth's foreshock

Using an evolutionary model and allowing for nonuniform proton injection and wave growth rates, the compressional wave boundaries corresponding to IMF inclinations to the solar wind of theta(BV) equal to 45 and 25 deg were located. The compressional boundaries deduced from this model were found to support the results of Greenstadt and Baum (1986) who have concluded that the observed compressional boundaries are incompatible with wave growth at a fixed growth rate, due to the interaction of a uniform beam with the solar wind. The results indicate, however, that the compressional boundaries are quite compatible with nonuniform beams and growth rates which result from the coupled evolution of the energetic protons and the waves with which they interact. It was found that, in the solar wind frame, the dominant wave-particle interaction in the outer foreshock is the damping of inward propagating (toward the shock) left-polarized waves, producing a magnetically quiet region immediately downstream of the foreshock boundary.

Skadron, George↗

NASA NTRS1987

The design and preliminary calibration of a boundary-layer flow channel

Design procedures for a new low-speed boundary-layer research channel are described. The channel is an open-circuit wind tunnel for the study of two-dimensional boundary layers under controlled pressure gradients, and follows design guidelines from published literature on blower tunnels with wide-angle diffusers. The contraction was arranged in a modular fashion permitting two different test sections of square and high-aspect-ratio cross section. A radical type of wide-angle diffuser was employed, and a stream-tube computer code (GE Streamtube Curvature Code) was used to check the contraction designs. The alternate test sections have the following specifications: 2- by 2-foot cross section with a fixed velocity of 23 ft/sec, and a boundary-layer section with a 0.5- by 2-foot cross section at a fixed velocity of approximately 89 ft/sec. Experimental techniques and data are described for the evaluation of diffuser effectiveness, boundary-layer channel characteristics, and overall performance of the facility.

Rao, Dhanvada M.↗

NASA NTRS1965

Necessary conditions for a multistage bolza- mayer problem involving control variables and having inequality and finite equation constraints

A multiplier rule and analogues of the Weierstrass and Clebsch conditions are developed for a multistage Bolza-Meyer calculus of variations problems. The number of stages is fixed, but partition points defining state boundaries are variable. Discontinuities are allowed in variables finite equations and inequalities, as well as differential equations, all of which involve control variables. An appendix summarizes some of the results obtained by C. H. Denbow, as modified by R. W. hunt, for a generalized Bolza problem. The appendix is independent of the rest of the paper.

Differential equation↗

NASA NTRS1976

A fast Karhunen-Loeve transform for a class of random processes

It is shown that for a class of finite first-order Markov signals, the Karhunen-Loeve (KL) transform for data compression is a set of periodic sine functions if the boundary values of the signal are fixed or known. These sine functions are shown to be related to the Fourier transform so that a fast Fourier transform algorithm can be used to implement the KL transform. Extension to two dimensions with reference to images with separable contravariance function is shown.

Jain, A. K.↗

NASA NTRS1976

Temperature and density structure of the corona and inner solar wind

A combined theoretical and observational approach is used to construct models of the inner corona applicable to quiet open-field regions and coronal holes. These models, extending from the top of the transition region at about 1.003 solar radii out to 3 solar radii, are calculated by employing parameters that describe the coronal geometry and heating. Thermal conductivity, heating, radiative losses, and solar-wind convection are included in the full energy-balance equation, which is integrated to obtain density and temperature models; the unknown heating term is parameterized in terms of the mechanical flux incident at the base and the characteristic scale height for the dissipation of this flux; and boundary conditions at the base are fixed by EUV-derived models of the transition region. Two representative models, one for a coronal hole and one for a quiet region, are examined in detail as illustrative examples of the technique used. It is noted that the models obtained predict most of the pertinent observations reasonably well but significantly overestimate the radio emission at 80 and 160 MHz and significantly underestimate the intensity of the Fe XV line at 284 A, especially in coronal holes.

Kopp, R. A.↗

NASA NTRS1984

Simulation of solidification in a Bridgman cell

The Hg/Cd/Te solidification in a Bridgman cell was thermally analyzed by Continuum's VAST code. The energy equation is solved in an axisymmetric, quasi steady domain for both the molten and solid alloy regions. Alloys composition is calculated by a simplified one dimensional model to estimate its effect on melt thermal conductivity and, consequently, on the temperature field within the cell. Solidification is assumed to occur at a fixed temperature of 979 K. Simplified boundary conditions are included to model both the radiant and conductive heat exchange between the furnace walls and the alloy. Calculations are performed to show how the steady state isotherms are affected by: (1) the hot and cold furnace temperatures; (2) boundary condition parameters; and (3) the growth rate which affects the calculated alloy's composition.

Dakhoul, Y. M.↗