SEARCH · Search NASA

Results for “flexibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Development of flexible rotor balancing criteria

Several studies in which analytical procedures were used to obtain balancing criteria for flexible rotors are described. General response data for a uniform rotor in damped flexible supports were first obtained for plain cylindrical bearings, tilting pad bearings, axial groove bearings, and partial arc bearings. These data formed the basis for the flexible rotor balance criteria presented. A procedure by which a practical rotor in bearings could be reduced to an equivalent uniform rotor was developed and tested. It was found that the equivalent rotor response always exceeded to practical rotor response by more than sixty percent for the cases tested. The equivalent rotor procedure was then tested against six practical rotor configurations for which data was available. It was found that the equivalent rotor method offered a procedure by which balance criteria could be selected for practical flexible rotors, using the charts given for the uniform rotor.

Walter, W. W.↗

NASA NTRS1980

On maneuvering large flexible spacecraft using an annular momentum control device

A scheme for the control and maneuvering of a large flexible spacecraft by means of two flexible AMCD's using noncontacting magnetic suspension is presented. The system consists of a flexible vehicle, two flexible rings and a magnetic suspension and driving assembly. The necessary skewing of the rings for maneuvering of the vehicle is accomplished by moving the pairs of magnets along tracks distributed around the circumference of the vehicle. The equations of motion for each subsystem are derived by the Lagrangian approach. Attitude motions are described in terms of quasi-coordinates. For small vehicle angular rates and rings attitude motions, an ordering scheme can be used to separate the equations of motion according to the magnitude of the terms. The ordered equations of motion lead to a linear time-variant optimal control problem for the maneuvering of the spacecraft.

Oz, H.↗

NASA NTRS1980

Singular perturbation equations for flexible satellites

Force equations of motion of the individual flexible elements of a satellite were obtained in a previous paper. Moment equations of motion of the composite bodies of a flexible satellite are to be developed using two sets of equations which form the basic system for any dynamic model of flexible satellites. This basic system consists of a set of N-coupled, nonlinear, ordinary, or partial differential equations, for a flexible satellite with n generalized, structural position coordinates. For single composite body satellites, N is equal to (n + 3); for dual-spin systems, N is equal to (n + 9). These equations involve time derivatives up to the second order. The study shows a method of avoiding this linearization by reducing the N equations to 3 or 9 nonlinear, coupled, first order, ordinary, differential equations involving only the angular velocities of the composite bodies. The solutions for these angular velocities lead to linear equations in the n generalized structural position coordinates, which can be solved by known methods.

Huang, T. C.↗

NASA NTRS1983

Effect of solar radiation disturbance on a flexible beam in orbit

The uncontrolled dynamics of an orbiting flexible beam in the presence of solar radiation pressure forces is considered. The effect of solar radiation forces and moments on the rigid and flexible modes of a free-free flexible beam is evaluated. It is found that moments result only from the flexible symmetric modal deformations. For small pitch amplitudes, and at near geosynchronous altitudes the solar radiation moments due to the deformations of the beam are seen to be greater than those due to the gravity-gradient. Within the linear range, simulated steady state dynamic responses show that the induced pitch amplitudes can be more significant than the induced amplitudes of the modal shape functions.

Krishna, R.↗

NASA NTRS1983

Structural dynamics studies of rotating bladed-disk assemblies coupled with flexible shaft motions

In order to analyze the dynamic behavior of the first stage compressor/fan of the 'E3' turbofan engine, a classical structural dynamics approach is employed to couple the motions of a flexible bladed disk to a rotating flexible shaft. The analysis accounts for flexible disk displacements which are transverse to the plane of rotation, and radial as well as tangential, and also accounts for rigid disk translations along, and rotations about, axes normal to the undeformed shaft axes. In the case of a wide range of E3 engine shaft flexibilities and speeds, some of the one-diametral node frequencies are shown to be affected by shaft degrees of freedom whose stiffness values are in general range of design practice. Coriolis forces are also found to significantly affect natural frequencies where strong coupling between certain modes is present.

Loewy, R. G.↗

NASA NTRS1982

Flexible radiator system: Executive summary

A full scale prototype flexible radiator panel was designed, built and tested. The panel, has approximately 173 sq ft of radiating area and is designed to reject 1.33 kW of heat to a 0 F sink with a 100 F fluid inlet. The panel is constructed from a flexible Teflon/silver mesh fin surrounding 1/8 inch Teflon tubes. The prototype panel is stowed on a 10 inch diameter by 4 foot wide drum. (It rolls up to a diameter of 17 inches when fully stowed). Deployment of the soft tube prototype is via two four inch diameter Kevlar/Mylar inflation tubes with flat springs incorporated in each tube. Nitrogen is normally used for the deployment with approximately 1 psi required. The springs retract the panels when the inflation tubes are deflated. Another method of deployment available for the soft tube flexible is a motor driven deployable boom. This eliminates the need for expendables when the panel area is varied during the mission for heat load control. The soft tube panel is designed for a 90% probability of no punctured tube in a 30 day mission. The acceptable working fluids for this soft tube flexible are Coolanol 15, Coolanol 20 and Glycol/water (a eutectic mixture).

Oren, J. R.↗

NASA NTRS1985

Direct model reference adaptive control of a flexible robotic manipulator

Quick, precise control of a flexible manipulator in a space environment is essential for future Space Station repair and satellite servicing. Numerous control algorithms have proven successful in controlling rigid manipulators wih colocated sensors and actuators; however, few have been tested on a flexible manipulator with noncolocated sensors and actuators. In this thesis, a model reference adaptive control (MRAC) scheme based on command generator tracker theory is designed for a flexible manipulator. Quicker, more precise tracking results are expected over nonadaptive control laws for this MRAC approach. Equations of motion in modal coordinates are derived for a single-link, flexible manipulator with an actuator at the pinned-end and a sensor at the free end. An MRAC is designed with the objective of controlling the torquing actuator so that the tip position follows a trajectory that is prescribed by the reference model. An appealing feature of this direct MRAC law is that it allows the reference model to have fewer states than the plant itself. Direct adaptive control also adjusts the controller parameters directly with knowledge of only the plant output and input signals.

Meldrum, D. R.↗

NASA NTRS1985

Control of an orbiting flexible square platform in the presence of solar radiation

An analysis is made of the dynamics of a thin, homogeneous, flexible square plate exposed to solar radiation disturbance. It is shown that only the first three flexible modes of the plate generate a first order net moment about the center of mass and that the solar radiation pressure does not influence the flexible modes of the plate for small-amplitude vibrations. In the absence of control, for a symmetrical homogeneous square platform, the solar radiation induces a steady angular drift about one of the body principal axes. For extremely flexible platforms, nominally oriented in the local horizontal plane, appreciable rigid modal amplitudes can be induced due to solar radiation, even in the presence of both active and passive control. Optimal control law and feedback gain values are obtained using linear quadratic Gaussian methods.

Bainum, P. M.↗

NASA NTRS1986

Adaptive control robustness in flexible aircraft application

This paper presents the application of a model reference adaptive control (MRAC) algorithm to flexible aircraft flight control. The algorithm is an adaptive version of the Command Generator Tracking (CGT) control technique. This technique forces a dynamic system to follow a reduced-order model, allowing it to cope with the problem of unmodeled dynamics. The studies were made via simulation, using for the plant an aircraft dynamic model similar to the B1 bomber. This model is of a large aircraft with a reasonable amount of structural flexibility. In particular, flight configurations were analyzed where the influence of the flexible modes make it difficult to control the aircraft. The results indicate that the algorithm has good robustness properties vis-a-vis unmodeled dynamics and can force the flexible aircraft to follow rigid body responses.

Sanchez, E. N.↗

NASA NTRS1987

Optimization procedure to control the coupling of vibration modes in flexible space structures

As spacecraft structural concepts increase in size and flexibility, the vibration frequencies become more closely-spaced. The identification and control of such closely-spaced frequencies present a significant challenge. To validate system identification and control methods prior to actual flight, simpler space structures will be flown. To challenge the above technologies, it will be necessary to design these structures with closely-spaced or coupled vibration modes. Thus, there exists a need to develop a systematic method to design a structure which has closely-spaced vibration frequencies. This paper describes an optimization procedure which is used to design a large flexible structure to have closely-spaced vibration frequencies. The procedure uses a general-purpose finite element analysis program for the vibration and sensitivity analyses and a general-purpose optimization program. Results are presented from two studies. The first study uses a detailed model of a large flexible structure to design a structure with one pair of closely-spaced frequencies. The second study uses a simple equivalent beam model of a large flexible structure to obtain a design with two pairs of closely-spaced frequencies.

Walsh, Joanne L.↗

NASA NTRS1987

Optimum vibration control of flexible beams by piezo-electric actuators

The utilization of piezoelectric actuators in controlling the structural vibrations of flexible beams is examined. A Modified Independent Modal Space Control (MIMSC) method is devised to enable the selection of the optimal location, control gains and excitation voltage of the piezoelectric actuators in a way that would minimize the amplitudes of vibrations of beams to which these actuators are bonded, as well as the input control energy necessary to suppress these vibrations. The developed method accounts for the effects that the piezoelectric actuators have on changing the elastic and inertial properties of the flexible beams. Numerical examples are presented to illustrate the application of the developed MIMSC method in minimizing the structural vibrations of beams of different materials when subjected to different loading and end conditions using ceramic or polymeric piezoelectric actuators. The obtained results emphasize the importance of the devised method in designing more realistic active control systems for flexible beams, in particular, and large flexible structures in general.

Baz, A.↗

NASA NTRS1987

Hub flexibility effects on propfan vibration

The significance of hub flexibility in the nonlinear static and dynamic analyses of advanced turboprop blades is assessed. The chosen blade is the 0.175 scale model of the GE-A7-B4 unducted fan blade. A procedure for coupling the effective hub stiffness matrix to an MSC/NASTRAN finite element model is defined and verified. A series of nonlinear static and dynamic analyses are conducted on the blade for both rigid and flexible hug configurations. Results indicate that hub flexibility is significant in the nonlinear static and dynamic analyses of the GE-A7-B4. In order to insure accuracy in analyses of other blades, hub flexibility should always be considered.

Ernst, Michael A.↗

NASA NTRS1987

Optimization procedure to control the coupling of vibration modes in flexible space structures

As spacecraft structural concepts increase in size and flexibility, the vibration frequencies become more closely-spaced. The identification and control of such closely-spaced frequencies present a significant challenge. To validate system identification and control methods prior to actual flight, simpler space structures will be flown. To challenge the above technologies it will be necessary to design these structures with closely-spaced or coupled vibration modes. Thus there exists a need to develop a systematic method to design a structure which has closely-spaced vibration frequencies. This paper describes an optimization procedure which is used to design a large flexible structure to have closely-spaced vibration frequencies. The procedure uses a general-purpose finite-element analysis program for the vibration and sensitivity analyses and a general-purpose optimization program. Results are presented from two studies. The first study uses a detailed model of a large flexible structure to design a structure with one pair of closely-spaced frequencies. The second study uses a simple equivalent beam model of a large flexible structure to obtain a design with two pairs of closely-spaced frequencies.

Walsh, Joanne L.↗

NASA NTRS1988

Rapid multi-flexible-body maneuvering experiments

Progress at the NASA Langley Research Center in the area of rapid multiple-flexible-body maneuvering experiments is described. The experiments are designed to verify theoretical analyses using control theory for the control of flexible structures. The objective of the maneuvering experiments is to demonstrate slewing of flexible structures in multiple axes while simultaneously suppressing vibration to have acceptable motion at the end of the maneuver. The status of some research activities oriented primarily to the experimental methods for control of flexible structures is presented.

Juang, Jer-Nan↗

NASA NTRS1987

Flexible structure control laboratory development and technology demonstration

An experimental structure is described which was constructed to demonstrate and validate recent emerging technologies in the active control and identification of large flexible space structures. The configuration consists of a large, 20 foot diameter antenna-like flexible structure in the horizontal plane with a gimballed central hub, a flexible feed-boom assembly hanging from the hub, and 12 flexible ribs radiating outward. Fourteen electrodynamic force actuators mounted to the hub and to the individual ribs provide the means to excite the structure and exert control forces. Thirty permanently mounted sensors, including optical encoders and analog induction devices provide measurements of structural response at widely distributed points. An experimental remote optical sensor provides sixteen additional sensing channels. A computer samples the sensors, computes the control updates and sends commands to the actuators in real time, while simultaneously displaying selected outputs on a graphics terminal and saving them in memory. Several control experiments were conducted thus far and are documented. These include implementation of distributed parameter system control, model reference adaptive control, and static shape control. These experiments have demonstrated the successful implementation of state-of-the-art control approaches using actual hardware.

Vivian, H. C.↗

NASA NTRS1988

Optimum vibration control of flexible beams by piezo-electric actuators

Baz, A.↗

NASA NTRS1989

End-point control of a two-link manipulator with a very flexible forearm - Issues and experiments

For mechanical manipulators, a logical sensor location is at the manipulator end-point where tasks are performed. Unfortunately, when bending flexibility exists between an end-point sensor and a joint actuator, stability and performance are achieved only through sophisticated control design. Some of the issues involved in utilizing end-point sensing for two-link flexible manipulators are addressed. A modeling technique that properly represents the foreshortening of a flexible link undergoing deflections is presented. In order to realize fully the advantages of the assumed-modes modeling method, mode shapes are selected that allow a low-order model to be used effectively for simulation and control purposes. A nonlinear controller, incorporating state feedback and a constant-gain extended Kalman filter driven by end-point measurements, is designed and compared to a conventional proportional-plus-derivative controller that uses collocated sensors. Results from implementing these controllers on the experimental Stanford multilink flexible manipulator are given.

Oakley, Celia M.↗

NASA NTRS1989

Linearized flexibility models in multibody dynamics and control

Simulation of structural response of multi-flexible-body systems by linearized flexible motion combined with nonlinear rigid motion is discussed. Advantages and applicability of such an approach for accurate simulation with greatly reduced computational costs and turnaround times are described, restricting attention to the control design environment. Requirements for updating the linearized flexibility model to track large angular motions are discussed. Validation of such an approach by comparison with other existing codes is included. Application to a flexible robot manipulator system is described.

Cimino, William W.↗