Search NASA⌕ Search

SEARCH · Search NASA

Results for “flutter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Evaluation of four subcritical response methods for on-line prediction of flutter onset in wind-tunnel tests

Four subcritical response methods were evaluated for on-line use in transonic wind-tunnel tests where the flutter model is excited solely by airstream turbulence. The methods were: randomdec, power-spectral-density, peak-hold, and cross-spectrum. Subcritical response data were obtained during tests in the Langley Transonic Dynamics Tunnel of a cantilevered flutter model wing. The test procedure was to maintain a constant Mach number and increase the dynamic pressure (q) in incremental steps. The four methods provided damping trends by which the flutter mode could be tracked and extrapolated to a flutter-onset q. A hard flutter point was obtained at M = 0.82. The peak-mold and cross-spectrum methods gave reliable results and could be most readily used for on-line testing.

Ruhlin, C. L.↗
NASA NTRS1982

Measured and calculated effects of angle of attack on the transonic flutter of a supercritical wing

The effects of angle of attack between 0 and 4 degrees were studied. The results indicate that increasing angle of attack from zero can produce substantial changes in the transonic flutter characteristics that are favorable or unfavorable depending on Mach number and angle of attack. The bottom of the transonic flutter-boundary 'bucket' is shown to occur at lower Mach number as angle of attack increases. These flutter results correlate well with the effects of Mach number and angle of attack on aerodynamic behavior, especially on the development of transonic flow phenomena. The calculated flutter characteristics are in good agreement with the experimental data at zero angle of attack, but at nonzero angles of attack the experiments show sharply declining and backward-turning transonic flutter boundaries that are not indicated by the calculations. These may be caused by variations in static aeroelastic deformation.

Yates, E. C., Jr.↗
NASA NTRS1981

Subsonic/transonic stall flutter investigation of a rotating rig

Stall flutter is investigated by obtaining detailed quantitative steady and aerodynamic and aeromechanical measurements in a typical fan rotor. The experimental investigation is made with a 31.3 percent scale model of the Quiet Engine Program Fan C rotor system. Both subsonic/transonic (torsional mode) flutter and supersonic (flexural) flutter are investigated. Extensive steady and unsteady data on the blade deformations and aerodynamic properties surrounding the rotor are acquired while operating in both the steady and flutter modes. Analysis of this data shows that while there may be more than one traveling wave present during flutter, they are all forward traveling waves.

Jutras, R. R.↗
NASA NTRS1984

Winglet effects on the flutter of twin-engine-transport type wing

Flutter characteristics of a cantilevered high aspect ratio wing with winglet were investigated. The configuration represented a current technology, twin-engine airplane. A low-speed and a high-speed model were used to evaluate compressibility effects through transonic Mach numbers and a wide range of mass-density ratios. Four flutter mechanisms were obtained in test, as well as analysis from various combinations of configuration parameters. The coupling between wing tip vertical and chordwise motions was shown to have significant effect under some conditions. It is concluded that, for the flutter model configurations studied, the winglet related flutter was amenable to the conventional flutter analysis techniques.

Bhatia, K. G.↗
NASA NTRS1984

Flutter parametric studies of cantilevered twin-engine-transport type wing with and without winglet. Volume 1: Low-speed investigations

Flutter characteristics of a cantilevered high aspect ratio wing with winglet were investigated. The configuration represented a current technology, twin-engine airplane. A low-speed and high-speed model were used to evaluate compressibility effects through transonic Mach numbers and a wide range of mass-density ratios. Four flutter mechanisms were obtained in test, as well as analysis from various combinations of configuration parameters. The coupling between wing tip vertical and chordwise motions was shown to have significant effect under some conditions. It is concluded that for the flutter model configurations studied, the winglet related flutter was amenable to the conventional flutter analysis techniques.

Bhatia, K. G.↗
NASA NTRS1986

Flight test of a decoupler pylon for wing/store flutter suppression

The decoupler pylon is a NASA concept of passive wing-store flutter suppression achieved by providing a low store-pylon pitch frequency. Flight tests were performed on an F-16 aircraft carrying on each wing an AIM-9J wingtip missile, a GBU-8 bomb near midspan, and an external fuel tank. Baseline flights with the GBU-8 mounted on a standard pylon established that this configuration is characterized by an antisymmetric limited amplitude flutter oscillation within the operational envelope. The airplane was then flown with the GBU-8 mounted on the decoupler pylon. The decoupler pylon successfully suppressed wing-store flutter throughout the flight envelope. A 37-percent increase in flutter velocity over the standard pylon was demonstrated. Maneuvers with load factors to 4g were performed. Although the static store displacements during maneuvers were not sufficiently large to be of concern, a store pitch alignment system was tested and performed successfully. One GBU-8 was ejected demonstrating that weapon separation from the decoupler pylon is normal. Experience with the present decoupler pylon design indicated that friction in the pivoting mechanism could affect its proper functioning as a flutter suppressor.

Cazier, F. W., Jr.↗
NASA NTRS1986

Flight test of a decoupler pylon for wing/store flutter suppression

The decoupler pylon is a NASA concept of passive wing-store flutter suppression achieved by providing a low store-pylon pitch frequency. Flight tests where performed on an F-16 airplane carrying on each wing an AIM-9J wingtip missile, a GBU-8 bomb near midspan, and an external fuel tank. Baseline flights with the GBU-8 mounted on a standard pylon established that this configuration is characterized by an antisymmetric limited amplitude flutter oscillation within the operational envelope. The airplane was then flown with the GBU-8 mounted on the decoupler pylon. The decoupler pylon successfully suppressed wing-store flutter thoughout the flight envelope. A 37-percent increase in flutter velocity over the standard pylon was demonstrated. Maneuvers with load factors to 4g were performed. Although the static store displacements during maneuvers were not sufficiently large to be of concern, a store pitch alignment system was tested and performed successfully. One GBU-8 was ejected demonstrating that weapon separation from the decoupler pylon is normal. Experience with the present decoupler pylon design indicated that friction in the pivoting mechanism could affect its proper functioning as a flutter suppressor.

Cazier, F. W., Jr.↗
NASA NTRS1984

Optimization of cascade blade mistuning under flutter and forced response constraints

In the development of modern turbomachinery, problems of flutter instabilities and excessive forced response of a cascade of blades that were encountered have often turned out to be extremely difficult to eliminate. The study of these instabilities and the forced response is complicated by the presence of mistuning; that is, small differences among the individual blades. The theory of mistuned cascade behavior shows that mistuning can have a beneficial effect on the stability of the rotor. This beneficial effect is produced by the coupling between the more stable and less stable flutter modes introduced by mistuning. The effect of mistuning on the forced response can be either beneficial or adverse. Kaza and Kielb have studied the effects of two types of mistuning on the flutter and forced response: alternate mistuning where alternte blades are identical and random mistuning. The objective is to investigate other patterns of mistuning which maximize the beneficial effects on the flutter and forced response of the cascade. Numerical optimization techniques are employed to obtain optimal mistuning patterns. The optimization program seeks to minimize the amount of mistuning required to satisfy constraints on flutter speed and forced response.

Murthy, D. V.↗
NASA NTRS1987

Static aeroelastic effects on the flutter of a supercritical wing

It is well known that wings with supercritical airfoils generally have lower transonic flutter speeds than similar wings with conventional airfoils and that small increases in angle of attack from zero and the accompanying static aeroelastic deformations have further detrimental effects on transonic flutter. The results of an effort to calculate the effects of angle of attack and the associated aeroelastic deformation on the flutter of a highly swept supercritical wing (TF 8A) by use of the modified strip analysis employed in previous studies of this wing are presented. The spanwise distributions of steady-state section lift-curve slope and aerodynamic center required as input for these calculations were obtained from static aeroelastic calculations for the wing by use of the FL022 transonic code and an assumed dynamic pressure as that used to calculate the statically deformed shape and loading about which the flutter oscillation occurs. The results show that the unconventional backward turn of the transonic dip in the experimental flutter boundary for angles of attack greater than zero is caused by variations in mass ratio and not by static aeroelastic deformation, although inclusion of the latter appears to be required for quantitative accuracy in the calculations.

Yates, E. Carson, Jr.↗
NASA NTRS1987

A technique for the prediction of airfoil flutter characteristics in separated flow

A solution procedure is described for determining the two-dimensional, one- or two-degree-of-freedom flutter characteristics of arbitrary airfoils at large angles of attack. The same procedure is used to predict stall flutter. This procedure requires a simultaneous integration in time of the solid and fluid equations of motion. The fluid equations of motion are the unsteady compressible Navier-Stokes equations, solved in a body-fitted moving coordinate system using an approximate factorization scheme. The solid equations of motion are integrated in time using an Euler implicit scheme. Flutter is said to occur if small disturbances imposed on the airfoil attitude lead to divergent oscillatory motions at subsequent times. Results for a number of special cases are presented to demonstrate the suitability of this scheme to predict flutter at large mean angles of attack. Some stall flutter applications are also presented.

Wu, Jiunn-Chi↗
NASA NTRS1988

The effects of rotational flow, viscosity, thickness, and shape on transonic flutter dip phenomena

The transonic flutter dip phenomena on thin airfoils, which are employed for propfan blades, is investigated using an integrated Euler/Navier-Stokes code and a two degrees of freedom typical section structural model. As a part of the code validation, the flutter characteristics of the NACA 64A010 airfoil are also investigated. In addition, the effects of artificial dissipation models, rotational flow, initial conditions, mean angle of attack, viscosity, airfoil thickness and shape on flutter are investigated. The results obtained with a Euler code for the NACA 64A010 airfoil are in reasonable agreement with published results obtained by using transonic small disturbance and Euler codes. The two artificial dissipation models, one based on the local pressure gradient scaled by a common factor and the other based on the local pressure gradient scaled by a spectral radius, predicted the same flutter speeds except in the recovery region for the case studied. The effects of rotational flow, initial conditions, mean angle of attack, and viscosity for the Reynold's number studied seem to be negligible or small on the minima of the flutter dip.

Reddy, T. S. R.↗
NASA NTRS1988

The effects of rotational flow, viscosity, thickness, and shape on transonic flutter dip phenomena

The transonic flutter dip phenomena on thin airfoils, which are employed for propfan blades, is investigated using an integrated Euler/Navier-Stokes code and a two degrees of freedom typical section structural model. As a part of the code validation, the flutter characteristics of the NACA 64A010 airfoil are also investigated. In addition, the effects of artificial dissipation models, rotational flow, initial conditions, mean angle of attack, viscosity, airfoil thickness, and shape on flutter are investigated. The results obtained with an Euler code for the NACA 64A010 airfoil are in reasonable agreement with published results obtained by using transonic small disturbance and Euler codes. The two artifical dissipation models, one based on the local pressure gradient scaled by a common factor and the other based on the local presure gradient scaled by a spectral radius, predicted the same flutter speeds except in the recovery region for the case studied. The effects of rotation flow, initial conditions, mean angle of attack, and viscosity for the Reynolds number studied seem to be negligible or small on the minima of the flutter dip.

Reddy, T. S. R.↗
NASA NTRS1990

Experimental transonic flutter characteristics of supersonic cruise configurations

The flutter characteristics of a generic arrow-wing supersonic transport configuration are studied. The wing configuration has a 3 percent biconvex airfoil and a leading-edge sweep of 73 deg out to a cranked tip with a 60 deg leading-edge sweep. The ground vibration tests and flutter test procedure are described. The effects of flutter on engine nacelles, fuel loading, wing-mounted vertical fin, wing angle-of-attack, and wing tip mass and stiffness distributions are analyzed. The data reveal that engine nacelles reduce the transonic flutter dynamic pressure by 25-30 percent; fuel loadings decrease dynamic pressures by 25 percent; 4-6 deg wing angles-of-attack cause steep transonic boundaries; and 5-10 percent changes in flutter dynamic pressures are the result of the wing-mounted vertical fin and wing-tip mass and stiffness distributions.

Durham, Michael H.↗
NASA NTRS1990

Finite element two-dimensional panel flutter at high supersonic speeds and elevated temperature

A consistent finite element formulation for flutter of two-dimensional panels including effects of temperature variation along panel length is presented. The von Karman nonlinear strain-displacement relation is used to account for the large-deflections, and the quasi-steady first-order piston theory is employed for aerodynamic loading in the finite-element formulation. The panel flutter under combined thermal/aerodynamic loading can be separated into solving two problems in sequence. They are: (1) postbuckling deflection, stresses and buckling stability boundary, and (2) critical dynamic pressure and linear flutter boundary. The solution procedures in solving these problems are presented in detail. Finite element results of two-dimensional panels with uniform temperature change are compared with classic analytical solutions. Influence of nonuniform temperature distributions on critical buckling temperature, flutter deflection and stresses, and flutter boundary is also given.

Xue, David Y.↗
NASA NTRS1991

An analytical and experimental study to investigate flutter suppression via piezoelectric actuation

The objective was to analytically and experimentally study the capabilities of adaptive material plate actuators for suppressing flutter. The validity of analytical modeling techniques for piezoelectric materials was also investigated. Piezoelectrics are materials which are characterized by their ability to produce voltage when subjected to a mechanical strain. The converse piezoelectric effect can be utilized to actuate a structure by applying a voltage. For this investigation, a two degree of freedom wind tunnel model was designed, analyzed, and tested. The model consisted of a rigid airfoil and a flexible mount system which permitted a translational and a rotational degree of freedom. It was designed such that flutter was encounted within the testing envelope of the wind tunnel. Actuators, made of piezoelectric material were affixed to leaf springs of the mount system. Each degree of freedom was controlled by a separate leaf spring. Command signals, applied to the piezoelectric actuators, exerted control over the damping and stiffness properties. A mathematical aeroservoelastic model was constructed using finite element methods, laminated plate theory, and aeroelastic analysis tools. Plant characteristics were determined from this model and verified by open loop experimental tests. A flutter suppression control law was designed and implemented on a digital control computer. Closed loop flutter testing was conducted. The experimental results represent the first time that adaptive materials have been used to actively suppress flutter. It demonstrates that small, carefully placed actuating plates can be used effectively to control aeroelastic response.

Heeg, Jennifer↗
NASA NTRS1992

Finite element nonlinear panel flutter with arbitrary temperatures in supersonic flow

A finite element frequency domain method for predicting nonlinear flutter response of panels with temperature effects is presented. By using the principle of virtual work, the element nonlinear stiffness formulation for a panel under a combined thermal and aerodynamic loads is derived on the bases of von Karman's large deflection plate theory, the first-order piston theory aerodynamics and the quasi-steady thermal stress theory. The system equations of motion can be mathematically separated into two sets of equations and then solved in sequence. The first set of equations yields the panel thermal-aerodynamic equilibrium and the second set of equations of motion leads to the flutter limit-cycle oscillations. Stability and flutter boundaries can also be obtained from the two sets of system equations. Finite element large amplitude limit-cycle flutter results at different uniform temperatures are obtained for a simply supported square panel and are compared with existing Galerkin/time integration and other finite element solutions. Effects of nonuniform temperature distributions, panel length-to-width ratios, and boundary conditions on flutter responses of rectangular and triangular panels are presented.

Xue, David Y.↗
NASA NTRS1989

A finite element method for nonlinear panel flutter

Panel flutter is the self excited oscillations of a plate in supersonic flow. Linear theory gives no information about the panel's deflections and stresses. Hence, the service life of the panel cannot be predicted by linear methods. Nonlinear structural theory determines the limit cycle oscillating frequency, and also panel deflections and stresses. Panel fatigue life, therefore, can be predicted. For a more thorough understanding of panel flutter behavior, the geometric nonlinearity effects due to large deflections must be considered in the formulation. The Galerkin's method was used in the investigation of limit cycle oscillations of panels in supersonic flow in the spatial domain, and the panel deflections. All nonlinear flutter methods and results presently available were limited to a linear or linearized aerodynamic theory. Extension of the finite element flutter formulation to include nonlinear hypersonic aerodynamic loading and finite element nonlinear panel flutter results are presented.

Mei, Chuh↗
NASA NTRS1993

Analytical and experimental investigation of flutter suppression by piezoelectric actuation

The objective of this research was to analytically and experimentally study the capabilities of piezoelectric plate actuators for suppressing flutter. Piezoelectric materials are characterized by their ability to produce voltage when subjected to a mechanical strain. The converse piezoelectric effect can be utilized to actuate a structure by applying a voltage. For this investigation, a two-degree-of-freedom wind tunnel model was designed, analyzed, and tested. The model consisted of a rigid wing and a flexible mount system that permitted a translational and a rotational degree of freedom. The model was designed such that flutter was encountered within the testing envelope of the wind tunnel. Actuators made of piezoelectric material were affixed to leaf springs of the mount system. Command signals, applied to the piezoelectric actuators, exerted control over the damping and stiffness properties. A mathematical aeroservoelastic model was constructed by using finite element methods, laminated plate theory, and aeroelastic analysis tools. Plant characteristics were determined from this model and verified by open loop experimental tests. A flutter suppression control law was designed and implemented on a digital control computer. Closed loop flutter testing was conducted. The experimental results represent the first time that adaptive materials have been used to actively suppress flutter. They demonstrate that small, carefully placed actuating plates can be used effectively to control aeroelastic response.

Heeg, Jennifer↗