SEARCH · Search NASA

Results for “fracture geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Mega-geomorphology and neotectonics

For several decades, subtle neotectonic effects involving several square kilometers have been studied in detail using remote sensing, primarily various types of stereo-aerial photographs at scales of 1:10,000 to 1:80,000. These subtle effects, especially local uplifts associated with growing structures of differential compaction, have been detected by the effect on drainage patterns, changes in hydraulic geometry of individuals channels or groups of channels, tonal halos (soil) and fracture patterns. The studies were extended with the advent of thermal IR imagery particularly in tonal analysis, and SLAR primarily in fracture pattern studies. Lately, quantitative efforts have begun attempting to link measured uplift over known structures with measured changes in hydraulic geometry and alluvial deposition. Thus, efforts are now underway attempting to quantify the relationship between neo- (micro-) tectonic changes and geomorphic parameters of drainage systems.

Lattman, L. H.↗

NASA NTRS2002

Gear Crack Propagation Path Studies-- Guidelines Developed for Ultrasafe Design

Effective gear designs balance strength, durability, reliability, size, weight, and cost. However, unexpected gear failures may occur even with adequate gear tooth design. To design an extremely safe system, the designer must ask and address the question "What happens when a failure occurs?" With regard to gear-tooth bending fatigue, tooth or rim fractures may occur. For aircraft, a crack that propagated through a rim would be catastrophic, leading to the disengagement of a rotor or propeller, the loss of an aircraft, and possible fatalities. This failure mode should be avoided. However, a crack that propagated through a tooth might or might not be catastrophic, depending on the design and operating conditions. Also, early warning of this failure mode might be possible because of advances in modern diagnostic systems. An analysis was performed at the NASA Glenn Research Center to develop design guidelines to prevent catastrophic rim fracture failure modes in the event of gear-tooth bending fatigue. The finite element method was used with principles of linear elastic fracture mechanics. Crack propagation paths were predicted for a variety of gear tooth and rim configurations. The effects of rim and web thicknesses, initial crack locations, and gear-tooth geometry factors such as diametral pitch, number of teeth, pitch radius, and tooth pressure angle were considered. Design maps of tooth and rim fracture modes, including the effects of gear geometry, applied load, crack size, and material properties were developed. The occurrence of rim fractures significantly increased as the backup ratio (rim thickness divided by tooth height) decreased. The occurrence of rim fractures also increased as the initial crack location was moved down the root of the tooth. Increased rim and web compliance increased the occurrence of rim fractures. For gears with constant-pitch radii, coarser-pitch teeth increased the occurrence of tooth fractures over rim fractures. Also, 25 degree pressure angle teeth increased the occurrence of tooth fractures over rim fractures in comparison to 20 pressure angle teeth. For gears with a constant number of teeth or for gears with constant diametral pitch, varying size had little or no effect on crack propagation paths.

Lewicki, David G.↗

DOE OSTI2025

Closing the Loop between In Situ Stress Complexity and EGS Fracture Complexity

We present an agent-guided approach to CAD geometry decomposition that automates hex/hybrid meshing with graph neural networks (GNNs) to accelerate next-generation ModSim workflows. Our end-to-end pipeline (i) reduces 3D boundary-representation (B-Rep) models to a 2D chordal axis skeleton (CAT) and then to a 1D bipartite graph of surface and curve nodes, (ii) assigns per node labels as Cubit® WebCut actions, (iii) trains a multi-action GNN under supervised learning, and (iv) predicts five surface-node and three curve-node actions on out-of-distribution test geometries. Each graph node carries geometric, topological, and meshing attributes drawn from the B-Rep “skin” and CAT “skeleton,” with two-way mappings across 3D↔2D↔1D representations to maintain traceability back to 3D CAD. The supervised learning model exhibits stable convergence of the binary cross-entropy loss and achieves 98.7% accuracy on unseen lattice models. To operationalize decision-making, we rank predicted commands by geometric significance and prototyped the agent-guided workflow through the Cubit® Meshing PowerTool GUI. As a stretch goal, we explore reinforcement learning (RL) to reduce or remove label requirements and to learn policies for action sequences that maximize total reward (e.g., size of hex-meshable regions and resulting hex mesh quality). When all-hex meshing is not feasible, the agent assists in producing hybrid meshes—prioritizing hex in critical regions and transitioning to tetrahedral elements (tets) elsewhere—maintaining fidelity while ensuring robustness. The overarching objective is to replace manual, heuristics-based decomposition with data-driven, reproducible automation, cutting meshing turnaround time by orders of magnitude. We anticipate direct impact on simulation workflows through intelligent, scalable decomposition of complex CAD models into hex-meshable subdomains.

42 ENGINEERING↗

NASA NTRS1985

Fracture of thick graphite/epoxy laminates with part-through surface flaws

Fracture behavior of tensile specimens containing through-the-thickness flaws and part-through semi-elliptic surface flaws was investigated. The material was T300/5208 graphite/epoxy, with a stacking sequence 0/+ or - 45/90 sub ns. Laminate thicknesses ranged from 8 to 120 plies. Fracture toughness for specimens with through-the-thickness flaws was a function of laminate thickness. Fracture toughness was also independent of crack size. Fracture toughness for the thick laminates was also independent of specimen geometry (center-cracked tension specimen, compact tension specimen, and three-point bend specimen). Using the asymptotic value of facture toughness and linear elastic isotropic fracture mechanics, the notched strength of tensile specimens with semi-elliptic surface flaws was predicted. The strength ratio is a function of the flaw depth (a/t) and flaw aspect (a/c) ratios. Comparisons between predicted and experimental strengths are good for large values of a/t. The notched strength of filament wound graphite/epoxy tensile specimens with part-through surface flaws was also predicted.

Morris, D. H.↗

DOE OSTI2022

Mode I tensile fracture behavior of adhesively-bonded metal–metal, metal–CFRP, and CFRP–CFRP bi-material combinations analyzed by size effect method

Understanding the adhesive and interfacial fracture is important for developing and achieving better adhesive jointing in bi-materials, the location which becomes less vulnerable in engineered structure components. Still, to characterize the fracturing behavior of various adhesively-bonded materials, it was shown in this work that the Mode I fracture energies estimated from conventional methods (e.g., work-of-fracture, (modified) compliance calibration method, (modified) beam theory, etc.) can be strongly affected by adherent thickness, adhesive bond length, and material type. Consequently, this hindered the proper understanding of fracturing in adhesive jointing of bi-materials since the estimated fracture energies can exhibit unreasonable difference among various material combinations, thus leading to the confusion in the literature due to the unfair comparison on these non-objective results estimated by leveraging conventional methods on the specimens with different geometries. This work compared size effect method with conventional methods on the calculation of the Mode I fracture energies of metal-metal, metal-CFRP, and CFRP-CFRP material combinations via Double Cantilever Beam (DCB) tests. The results showed that the estimated fracture energies of various material combinations are not dependent on the specimen geometries. This aspect allowed the fair comparison particularly on the interfacial fracturing between metal/adhesive and CFRP/adhesive, and the difference was further explained and correlated with the damage morphology on the material surface after failure identified through three-dimensional profilometer.

36 MATERIALS SCIENCE↗

NASA NTRS1984

On the use of the three point bend and compact tension specimens to measure fracture toughness of composite laminates

The influence of specimen thickness on the fracture toughness of two laminates and three specimen geometries was investigated. As thickness increased the toughness decreased and approached an asymptotic value that was dependent upon the type of laminate but was practically independent of specimen geometry. Enhanced X-ray photographs and removal of an outside ply revealed that most of the delaminations were surface effects.

Harris, C. E.↗

NASA NTRS1987

Damage growth in composite laminates with interleaves

The influence of interleaves on the fracture behavior of laminated composites is investigated. The geometry of the composite consists of a cracked layer, bonded between two half-planes, which is separated by thin, low modulus, interleaves. The interleaves are modeled as uncoupled tension and shear springs. A stress analysis is carried out for a crack which may grow up to and spread along the interface. Integral transform techniques are used to develop the solution in terms of singular integral equations. An asymptotic analysis reveals logarithmic singularities in the critical stresses for the case of a broken layer. The equations are solved numerically and the effect of damage on critical stresses is studied. Initial results indicate that the interleaf gives a significant reduction in stresses in the adjacent regions and, if properly selected, should result in a more damage tolerant laminate.

Goree, James G.↗

NASA NTRS2007

Friction stir weld tools

A friction stir weld tool sleeve is supported by an underlying support pin. The pin material is preferably selected for toughness and fracture characteristics. The pin sleeve preferably has a geometry which employs the use of an interrupted thread, a plurality of flutes and/or eccentric path to provide greater flow through. Paddles have been found to assist in imparting friction and directing plastic metal during the welding process.

Carter, Robert W.↗

NASA NTRS2007

Friction Stir Weld Tools

Carter, Robert W.↗

NASA NTRS1972

On fracture phenomena in advanced fiber composite materials.

The extension of linear elastic fracture mechanics (LEFM) from metallic alloys to advanced fiber composite laminates is considered. LEFM is shown to be valid for both isotropic and anisotropic homogeneous continua; the applicability of LEFM to advanced fiber composites is thus dependent on the validity of a homogeneous model of such materials. An experimental program to determine the validity of such a model for graphite/epoxy laminates is reviewed. Such laminates are found to have an apparent fracture toughness, from which it is inferred that a homogeneous material model is valid for the particular specimen geometry and composite laminates considered. Strain energy release rates are calculated from the experimentally determined fracture toughness of the various laminates. These strain energy release rates are found to lie in one of two groups, depending upon whether crack extension required fiber failure or matrix failure. The latter case is further investigated. It is concluded that matrix failure is governed by the tensile stress normal to the crack path.

Konish, H. J., Jr.↗

DOE OSTI2023

Molecular Dynamics Simulations of Calcite Fracture in Water

Calcite (CaCO 3 ) is one of the most common minerals in geologic and engineered systems. It is often in contact with aqueous solutions, causing chemically assisted fracture that is critical to understanding the stability of subsurface systems and manmade structures. Calcite fracture was evaluated with reactive molecular dynamics simulations, including the impacts of crack tip geometry (notch), the presence of water, and surface hydroxyl groups. Chemo-mechanical weakening was assessed by comparing the loads where fracture began to propagate. Our analyses show that in the presence of a notch, the load at which crack growth begins is lower, compared to the effect of water or surface hydroxyls. Additionally, the breaking of two adjacent Ca–O bonds is the kinetic limitation for crack initiation, since transiently broken bonds can reform, not resulting in crack growth. In aqueous environments, fresh (not hydroxylated) calcite surfaces exhibited water strengthening. Manual addition of H + and/or OH – species on the (104) calcite surface resulted in chemo-mechanical weakening of calcite by 9%. Achieving full hydroxylation of the calcite surface was thermodynamically and kinetically limited, with only 0.17–0.01 OH/nm 2 surface hydroxylation observed on the (104) surface at the end of the simulations. In conclusion, the limited reactivity of pure water with the calcite surface restricts the chemo-mechanical effects and suggests that reactions between physiosorbed water and localized structural defects may be dominating the chemo-mechanical process in the studies where water weakening has been reported.

Calcite↗

NASA NTRS2018

ASTM E399 Standard Development - KIsi Analysis Method

The ASTM E399 test method is used to determine the plane‐strain fracture toughness, K (sub IC), for metallic materials. The test consists of monotonically loading a pre-cracked test specimen to failure while recording the applied load and the crack mouth opening displacement. Several test specimen types are allowable per ASTM E399; two common geometries are the compact tension (C(T)) and the single-edge bend (SE(B)) geometries. The test result is an estimate of the plane‐strain fracture toughness, K (sub q), determined by the intercept of the test record with a 95 percent secant-offset construction line. The 95 percent offset represents crack extension corresponding to approximately 2 percent of the original specimen ligament (assuming that all compliance change is the result of crack extension). If the test meets certain validity requirements based on specimen size and test behavior, the result is valid, and K (sub q) equals K (sub IC).

Tilson, William G.↗

DOE OSTI2020

Predictive Inverse Model for Advective Heat Transfer in a Short–Circuited Fracture: Dimensional Analysis, Machine Learning, and Field Demonstration

Identifying fluid flow maldistribution in planar geometries is a well–established problem in subsurface science/engineering. Of particular importance to the thermal performance of enhanced (or “engineered”) geothermal systems is identifying the existence of nonuniform (i.e., heterogeneous) permeability and subsequently predicting advective heat transfer. Here, machine learning via a genetic algorithm (GA) identifies the spatial distribution of an unknown permeability field in a two–dimensional Hele–Shaw geometry (i.e., parallel plates). The inverse problem is solved by minimizing the L2 norm between simulated residence time distribution (RTD) and measurements of an inert tracer breakthrough curve (BTC) (C–Dot nanoparticle). Principal component analysis (PCA) of spatially correlated permeability fields enabled reduction of the parameter space by more than a factor of 10 and restricted the inverse search to reservoir–scale permeability variations. Thermal experiments and tracer tests conducted at the mesoscale Altona Field Laboratory (AFL) demonstrate that the method accurately predicts the effects of extreme flow channeling on heat transfer in a single bedding–plane rock fracture. However, this is only true when the permeability distributions provide adequate matches to both tracer RTD and frictional pressure loss. Without good agreement to frictional pressure loss, it is still possible to match a simulated RTD to measurements, but subsequent predictions of heat transfer are grossly inaccurate. Here, the results of this study suggest that it is possible to anticipate the thermal effects of flow maldistribution, but only if both simulated RTDs and frictional pressure loss between fluid inlets and outlets are in good agreement with measurements.

42 ENGINEERING↗

NASA NTRS1979

Mechanics of fracture - Fundamentals and some recent developments

An overview is presented of the fundamental aspects of and recent developments in fracture mechanics. Reference is made to linear elastic fracture mechanics including the state of stresses and displacements in the vicinity of cracks, effects of crack geometry and orientation on stress intensity factors, energy balance of Griffith, Irwin's stress intensity concept, and linear elastic fracture mechanics testing for fracture toughness. Other aspects of this paper include the non-linear behavior of materials and their influence on fracture mechanics parameters, consideration of viscoelasticity and plasticity, non-linear fracture toughness parameters as C.O.D., R-curve and J-integral, and a non-linear energy method, proposed by Liebowitz. Finite element methods applied to fracture mechanics problems are indicated. Also, consideration has been given to slow crack growth, dynamic effects on K(IC), Sih's criterion for fracture, Lee and Liebowitz's criterion relating crack growth with plastic energy, and applications of fracture mechanics to aircraft design. Suggestions are offered for future research efforts to be undertaken in fracture mechanics.

Liebowitz, H.↗

NASA NTRS1973

Fracture mechanics technology for optimum pressure vessel design.

A technique has been developed to design a maximum efficiency reliable pressure vessel of given geometry and service life. The technique for ensuring reliability of the minimum weight vessel relies on the application of linear elastic fracture mechanics and fracture mechanics concepts. The resultant design incorporates potential fatigue and stress corrosion crack extension during service of a worst case initial flaw. Maximum stress for safe life is specified by the design technique, thereby minimizing weight. Ratios of pressure and toughness parameters are employed to avoid arbitrary specification of design stress level which would lead to a suboptimum design.

Bjeletich, J. G.↗

NASA NTRS1985

An Elastic Analysis of a Plated Bone to Determine Fracture Gap Motion

An elastic analysis to determine fracture gap motions occurring in the osteotomized and plated canine femur was performed using the finite element program NASTRAN. The femur was idealized as a hollow right cylinder, and transverse anisotropy was assumed for the elastic properties of the bone. A 3-D 360 degree model consisting of 224 isoparametric quadrilateral hexahedral and 11 beam elements was created. A range of plate stiffnesses was tested by varying the modulus of elasticity of the plate from 207 GPa to 1 GPA. Moments were applied in the plane of the plate, about the axis of the plate, and in the plane of the screws. Results showed that, for plates of typical geometry and elastic modulus under 10 GPa, the contribution to fracture gap motion occurring due to deformation in the bone was negligible compared to that contribution from deformation in the plate.

Cooke, F. W.↗

NASA NTRS1990

Progression of damage and fracture in composites under dynamic loading

A new computational simulation method is presented to evaluate the dynamic aspects of composite structural response and durability that could not be simulated previously. Composite structural behavior under any loading, geometry, composite system, laminate configuration, and boundary conditions can now be simulated. Structural degradation, delamination, fracture, and damage propagation are included in the simulation. An angle-plied composite plate structure under normal impact loading is used as an example to demonstrate the versatility of the simulation method.

Minnetyan, Levon↗

NASA NTRS1986

Delamination growth in composite materials

The Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) specimens are employed to characterize MODE I and MODE II interlaminar fracture resistance of graphite/epoxy (CYCOM 982) and graphite/PEEK (APC2) composites. Sizing of test specimen geometries to achieve crack growth in the linear elastic regime is presented. Data reduction schemes based upon beam theory are derived for the ENF specimen and include the effects of shear deformation and friction between crack surfaces on compliance, C, and strain energy release rate, G sub II. Finite element (FE) analyses of the ENF geometry including the contact problem with friction are presented to assess the accuracy of beam theory expressions for C and G sub II. Virtual crack closure techniques verify that the ENF specimen is a pure Mode II test. Beam theory expressions are shown to be conservative by 20 to 40 percent for typical unidirectional test specimen geometries. A FE parametric study investigating the influence of delamination length and depth, span, thickness and material properties on G sub II is presented. Mode I and II interlaminar fracture test results are presented. Important experimental parameters are isolated, such as precracking techniques, rate effects, and nonlinear load-deflection response. It is found that subcritical crack growth and inelastic materials behavior, responsible for the observed nonlinearities, are highly rate-dependent phenomena with high rates generally leading to linear elastic response.

Gillespie, J. W., Jr.↗