Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel cycle length”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Characterization of Alloy 709 Commercial Heats

The creep-resistant austenitic stainless steel Alloy 709 (Fe-20Cr-25Ni (wt%) based steel) is being investigated as a candidate structural material for the next generation of advanced reactors. Unlike conventional solid solution strengthened austenitic stainless steels, Alloy 709 develops a variety of precipitates during aging at different temperatures and times. In this study, precipitate evolution during short-term aging at 775°C was characterized. The effect of aging time (e.g., 10 vs. 100 hours) and cooling after aging (e.g., water quench vs. air cool) on grain size and precipitates have been investigated using light optical microscopy (OM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and energy-dispersive X-ray spectroscopy (EDS). MX (Ni,Tb)(C,N) and M23C6 (Cr,Mo)C precipitates were observed in all the statically-aged samples. The grain size distribution in the sample aged for 10 hours and water quenched (10Q) versus the one aged for 100 hours and air cooled (100A) were comparable. This indicates that grain structure was fairly stable when aging at 775°C for up to 100 hours. In contrast, the sample aged for 10 hours and air cooled (10A) showed the smallest and the most uniform grain size distribution. This phenomenon was observed in only one sample. More studies on duplicate samples are needed to confirm the results obtained. The cooling medium (e.g., water quench vs. air cool) was not observed to impact the size nor the distribution of the MX and M23C6 precipitates. Increasing the aging time resulted in the following: (1) a decrease in dislocations as well as the number density of small precipitates; (2) an increase in the ratio of free precipitates that were not pinning dislocations; (3) relatively higher N, Nb, and Ti concentration in MX precipitate; (4) some increase in length of M23C6 carbides which were located on the coherent boundaries; and (5) the introduction of Sienriched M6X precipitates. The tensile tests at room temperature showed similar properties for each of the static aging treatments, indicating that the differences observed in the microstructural analysis did not have a significant impact on the tensile properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Fuel Bonding and its Impact on Axial Gas Communication Behavior in Light-Water Reactor Fuel Rods

Axial gas communication concerns the flow along the axial axis of nuclear fuel rods during ramp and loss of coolant accident (LOCA) conditions. During power ramps, the higher linear heat generation rate may cause fuel-to-clad gap closure that may prevent transport of released fission gases to the plenum. Upon reduction in power the gas then can communicate to the plenum. This phenomenon has been experimentally observed by short power dips during ramp experiments completed at the Risø reactor. At higher burnups it is observed that the UO2 fuel and Zircaloy cladding forms a chemical bond. This bond results in complete closure of the gap. When these high burnup rods are subjected to a LOCA, the bond has implications on both the mechanical response (i.e., ballooning) of the cladding and subsequent fuel relocation and axial gas communication. In the LOCA scenario, gas communication is of interest in two different regimes: 1) pre-rupture communication from the plenum towards the lower pressure ballooning area and 2) the post-rupture depressurization of the plenum to the external system pressure. In both regimes the presence of a fuel-to-cladding bond will impact the rate of depressurization. In this work we present a fuel-to-clad bonding model that is coupled to an existing axial gas communication model framework in the BISON fuel performance code. The effect of considering the bond on fuel performance modeling predictions is presented through comparisons to existing experimental data. Experiments considered include several rods from the Halden IFA-650 test series. An evaluation on a full-length rod that explores the combined effect of plenum size and bonding status on axial gas communication behavior is also presented.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

2022 roadmap on low temperature electrochemical CO 2 reduction

Abstract Electrochemical CO 2 reduction (CO 2 R) is an attractive option for storing renewable electricity and for the sustainable production of valuable chemicals and fuels. In this roadmap, we review recent progress in fundamental understanding, catalyst development, and in engineering and scale-up. We discuss the outstanding challenges towards commercialization of electrochemical CO 2 R technology: energy efficiencies, selectivities, low current densities, and stability. We highlight the opportunities in establishing rigorous standards for benchmarking performance, advances in in operando characterization, the discovery of new materials towards high value products, the investigation of phenomena across multiple-length scales and the application of data science towards doing so. We hope that this collective perspective sparks new research activities that ultimately bring us a step closer towards establishing a low- or zero-emission carbon cycle.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

3D analysis of TRISO fuel compacts via X-ray computed tomography

In this study, low-enriched uranium oxycarbide (LEUCO) and surrogate tristructural isotropic (TRISO)- coated-particle compacts with particle volumetric packing fractions of 25%, 40%, and 48% were imaged utilizing X-ray-computed tomography. Subsequent 3D image analysis identified and further quantified kernel size, sphericity, and observed porosity. In addition, the spatial distribution, coordination number, and kernel-nearest neighbors were analyzed and compared for the different packing fractions. Metrics such as observed porosity and sphericity enabled quantification and screening for abnormal kernels within TRISO compacts. Assessment of TRISO particle location confirmed and further quantified a non-uniform distribution of TRISO particles with the spatial distribution in the radial direction being roughly described as a dampened sinusoidal function. The amplitude and frequency of this non-uniform distribution increased with increasing packing fraction. Measured kernel-nearest neighbor distances indicated two regions along the radial surfaces of compacts where TRISO particles are more likely to be in intimate contact with one another. These regions were found: (1) at upper and lower faces of compacts (i.e., corners); (2) offset ~10% of a compact's length from the axial center near the exterior surface. Within these regions, small quantities of defective TRISO surrogate particles (48% packing fraction) and defective LEUCO TRISO particles (40% packing fraction) were found. No defective particles were found within 25% packing fraction LEUCO TRISO compacts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Integrating Chemical Catalysis and Biological Conversion of Carbon Intermediates for Deriving Value-Added Products from Carbon Dioxide

Carbon dioxide valorization represents an appealing approach to reducing greenhouse gases in the atmosphere. While electrocatalysis is an effective tool to reduce CO 2 into small carbon compounds, it becomes increasingly challenging to efficiently produce compounds with more carbon atoms. In contrast, while biological systems struggle to utilize CO 2 , they can readily upcycle other small carbon compounds. This project explores the use of a two-stage process that electrocatalytically converts CO 2 into methanol, formate, or acetate which is subsequently utilized by Methylotuvimicrobium alcaliphilum 20Z to produce medium chain length polyhydroxyalkanoate. A techno-economic analysis and life cycle assessment evaluates the commercial viability of the process as well as its carbon emissions. We show here an enhanced CO 2 -to-methanol electroconversion step coupled with the use of a microbial culture adapted to the process conditions to be the optimal configuration for economic potential.

09 BIOMASS FUELS↗
DOE OSTI2023

Friction Experiment Data Analysis

The Spent Fuel Waste Disposition (SFWD) program under the U.S. Department of Energy (DOE) is planning a seismic shake table test of full-scale dry storage systems of spent nuclear fuel (SNF) to close the gap related to the seismic loads on the fuel assemblies in dry storage systems. This test will allow for quantifying the strains and accelerations on surrogate fuel assembly during representative earthquakes. A concrete layer will be installed on the shake table before the test to simulate conditions representative of an ISFSI pad. In the shake table tests with the vertical cask, the cask will be free-standing because this is representative of all, except two, ISFSIs in the U.S. with vertical dry storage casks. The static and dynamic friction coefficients between the steel bottom of the cask and the concrete layer on the shake table are important parameters that will affect cask behavior during the test. These parameters must be known for the pre- and post-test modelling, data analysis, and model validation. The friction experiment was performed at the Engineering Department of the University of New Mexico (UNM) to determine the friction coefficients between a steel plate with the same finish as the bottom of the vertical cask manufactured for the test and different concrete surfaces. In this experiment the steel plate was fixed and the concrete sample was pulled over the plate with a constant displacement rate using an MTS machine. This allowed for collecting continuous horizontal force data over the length of the steel plate. Four displacement rates and three vertical loads were used. The tests were performed with four concrete blocks with different degrees of the surface roughness - light sandblast, light to medium sandblast, medium bush hammer, and heavy sandblast. The total number of tests was 48. The data were used to calculate static and dynamic friction coefficients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Adsorptive denitrogenation of model aviation fuel using mesoporous silica in a packed bed adsorption system

This study aims to understand the effects of system process parameters such as flow rate, adsorbent particle size, and use of recycled adsorbent on denitrogenation performance of a model fuel using mesoporous silica gel. The goal is to reduce the nitrogen content of the model fuel from 1500 parts per million to single-digit ppm to meet ASTM specifications for drop-in fuels. This work was done with the intent of applying adsorptive denitrogenation to sustainable aviation fuel (SAF) product fractions produced via hydrothermal liquefaction (HTL). The adsorption performance of the silica is evaluated via packed column breakthrough data, with data generated from collecting from the column outlet and quantifying nitrogen content via gas chromatography. Select experiments use a significantly larger (2.5x column diameter and length) column to demonstrate linear scalability of the process. Thermogravimetric analysis data is collected to evaluate the effects of thermal calcination as a sorbent regeneration method. Effects of a more complex feed are also investigated using a known reference fuel with additional added nitrogen containing compounds. The results presented in this work successfully demonstrate up to 99.8 % removal of NCCs from a model fuel fraction at an original NCC concentration of approximately 1500 ppm to single-digit parts per million after treatment. We also examine calcination of sorbent materials to remove the adsorbed species to enable sorbent reuse and minimize waste generation and show that the calcined material can be reused up to 5 cycles with reduced adsorption capacity. Overall, this work indicates that adsorptive denitrogenation using silica gel is a viable solution to enable the integration of HTL-derived aviation fuels into existing fuel infrastructure.

Adsorption techniques↗
DOE OSTI2021

Correlating Nanoscale Secondary Ion Mass Spectrometry and Atom Probe Tomography Analysis of Uranium Enrichment in Metallic Nuclear Fuel

Distribution and enrichment of 235U within nuclear fuels are essential to material performance and reactor safety. With the development of metallic U fuels, understanding 235U homogeneity has become increasingly important, however, it is difficult to map with high spatial, and mass resolution to analyze both matrix and secondary phase precipitates. Here, we analyze 235U enrichment in matrix and carbide phases in LEU-Mo via two chemical imaging modalities: nanoscale secondary ion mass spectrometry (nanoSIMS) and atom probe tomography (APT). NanoSIMS and APT provided consistent results, with no statistically significant difference between measured and nominal enrichment (19.75 % 235U).

U-10Mo, atom probe tomography, nanoscale secondary↗
DOE OSTI2024

Core Design Optimization of the Westinghouse Lead Fast Reactor

Westinghouse is pursuing an advanced Nuclear Power Plant design based on Lead Fast Reactor (LFR) technology for global commercialization. To achieve an optimal combination of key attributes, such as safety, sustainability, and economic competitiveness, Westinghouse and ANL partnered in developing and applying a formalized core design optimization strategy. An LFR analysis workflow was developed to automate a suite of reactor physics, fuels performance, safety, and economics simulations on a selected LFR concept. The workflow streamlines analysis of a wide range of LFR designs with different dimensions and fuel types to assess their viability and economic performance, significantly reducing human processing time and risks of processing errors. The LFR optimization exercise was defined, resulting in selection of the design constraints (geometric, neutronics, thermo-mechanical, safety, thermal-hydraulics, and economics) and performance metrics researched (minimization of both the fuels LCOE and the first core inventory cost). A total of 14 varied design parameters were considered, including assembly dimensions, coolant temperature, and enrichment distribution throughout the core. The LFR analysis workflow was connected to DAKOTA for sensitivity and optimization analyses. Due to the extremely large size of the potential LFR optimization solution space relative to the computing time required to characterize one LFR solution, a multi-stage optimization approach was proposed to breakdown the problem into several stages with more reasonable sizes. This optimization approach enabled finding various viable core solutions with different cost tradeoffs that were considered by Westinghouse and justify selection of a smaller core with multi-batch 2-year cycle length.

Stauff, Nicolas E.↗
DOE OSTI2022

Advanced Autonomous Welding for Refabrication and Follow-On Testing of Previously Irradiated Nuclear Fuel

The performance of follow-on experiments using irradiated nuclear fuel at any point in its lifecycle is a critical step in understanding phenomena and behavior. Transient experiments with high-burnup fuel can deepen the understanding of fuel fragmentation, relocations, and dispersal under loss-of-coolant accidents. An advanced autonomous welding process to refabricate commercial fuel rods inside a hot cell was created and tested to enable flexible experiment approaches on fuels irradiated in commercial and test reactors. Irradiated light water reactor fuel test pins from experiments performed at the Advanced Test Reactor (ATR) at Idaho National Laboratory were used to demonstrate the refabrication process. The welding process was found to be sensitive to welding parameters but flexible such that multiple passes could be performed on the same location until a hermetic weld was obtained. The refabrication of rodlets and successful welds was also found to be sensitive to the preparation of the irradiated cladding and endcaps. Thorough defueling of the fuel at the weld location and proper sizing of the endcaps and backing material mitigated these issues. The use of strategically located heat sinks in contact with the cladding and endcap materials also increased welding and refabrication success. For this work, the test pins were sectioned to remove the original endcaps and fuel was removed from both ends of each rodlet. The reassembly of the rodlets was then completed in four steps, which included the press fitting of new endcaps, the circumferential welding of rodlet endcaps to the cladding, rodlet pressurization in a pressure chamber, and seal welding the rodlet under pressure. The integrity of the refabricated rodlets was then verified via helium leak checking inside a vacuum chamber. The advanced welding system is capable of refabricating rodlets up to 380 mm in length, and repressurizing them up to 15 500 kPa. The refabricated lengths of the rodlets used in this work ranged from 149 to 165 mm and the refabricated fuel stack heights ranged from 70.4 to 79.8 mm. Here, the rodlets were pressurized with argon to an average pressure of 3617 kPa, and the average leak rate after refabrication was 6.7 • 10 -8 cm 3 • s -1 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Integrated Approach to Post-Irradiation Examination of Nuclear Materials at Idaho National Laboratory

Idaho national Laboratory (INL) is the U.S. lead national laboratory for the Department of Energy’s Office of Nuclear Energy (DOE-NE), providing much of the nuclear research, development and demonstration capability needed to move nuclear innovation forward to deployment. INL’s Materials and Fuels Complex hosts a unique combination of personnel, facilities and infrastructure and offers the ability to perform post-irradiation examinations (PIE) of nuclear materials spanning multiple length scales. The ability to combine engineering-scale analysis and sub-microscopic characterization provides valuable insights into fuel and structural material behavior and degradation mechanisms. The holistic approach is used to accelerate these materials demonstration and deployment. Selected studies will be presented, highlighting the impact of these techniques on improving fuel reliability, safety, and efficiency, thereby advancing the development of sustainable and advanced nuclear energy technologies.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Passive Temperature Sensors for Nuclear Applications

Thermocouples are generally used to provide real-time temperature indications in instrumented tests performed at material and test reactors. Passive temperature monitors, such as Silicon Carbide (SiC) and melt wires, may be included in such tests as an independent technique of detecting peak temperatures experienced during irradiation. In less expensive static (drop-in) capsule tests, which have no leads attached for real-time data transmission, melt wires, and SiC temperature monitors (TMs) are essentially the only possibility for peak temperature indication. A melt wire involves placing materials (wires) of a known composition and melting temperature in a test. An inventory is maintained at Material Science Laboratory (MSL) for melt wires ranging in temperatures from 30°C to 1500°C. Unfortunately, melt wires are limited in that it can only detect whether a single temperature is or is not exceeded (melt wire melted or not). SiC TMs, which can also be used to detect peak irradiation temperatures, are advantageous because a single monitor can allow to determine the peak temperature reached within a relatively broad range (100 – 1200°C) resulting in accuracies within ±20°C. Irradiation temperature is determined by measuring a property change after isochronal annealing or during a continuously monitored annealing process using specialized equipment at MSL. Recent research has produced a passive monitor known as sublime temperature monitor. This passive sensor has the capability of recording temperature gradients and pinpointing exactly where a temperature is located along that gradient. Long measurement lengths are achieved with very high accuracy in the location of desired temperature measurements (±2 mm over a 1 m span); however, this sensor has not been deployed in a nuclear reactor. This article will focus only on passive temperature sensors currently being researched and implemented under the Advanced Sensors and Instrumentation (ASI) program at Idaho National Laboratory (INL).

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

A novel fiber-fretting test for tribological characterization of the fiber/matrix interface

Ceramic matrix composites exhibit excellent high temperature properties and are candidate materials for structural applications from jet engines to nuclear fuel cladding. The strength and deformation behavior of these composites are intrinsically tied to the properties of the fiber/matrix interface. This research introduces a novel technique to evaluate the fundamental friction and wear characteristics of these interfaces. A case study on SiC f /PyC/SiC m composites applies in situ fiber fretting to investigate the kinetic friction coefficient and cyclic wear characteristics of the interphase. The experimental methodology is presented in explicit detail to encourage other researchers to explore the capabilities of this technique. Additionally, testing was carried out as a function of fiber roughness, PyC thickness (≈10, 500, 1200 nm), cycle count (10, 100, 1000), and frequency (1, 5, and 10 Hz). The friction coefficient and wear behavior changed with cycle length due to a transition from adhesive to abrasive mechanisms. SEM fractography provided insights to tribological evolution from adhesive sliding to three-body abrasive wear. The structural disorder at the tribo-surface relating to graphitic content and dangling bond density was investigated using Raman spectroscopy. Properties are contextualized with comparison to uniaxial tensile behavior of the parent composite.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Develop and Connect TRISO Failure Analysis and Uncertainty Quantification to Fission Product Release Calculation Capability

The U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering-scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. Stress-based failure probability has been developed and analyzed to assess the integrity of tri-structural isotropic (TRISO) fuel particles during fuel life cycles. While simple, stress-based approaches to failure probability leveraging the Weibull statistical distribution entails a number of drawbacks when stress concentration occurs near crack tips, including finite element mesh size dependency. In this report, we use an interaction integral approach to the computation of stress intensity factors in functionally graded materials (FGM) for axisymmetric models. The inner pyrolytic carbon (IPyC) cracking induced silicon carbide (SiC) failure is one of the dominated failure modes in TRISO failure analysis. In this study, we consider a crack in the IPyC layer perpendicular to the SiC layer. The interface between these two TRISO layers is considered to be porous, which we simulate considering a transition of mechanical properties over the porous length. These aspects are considered in the computation of stress intensity factor (SIF) from a fracture mechanics approach and compared with the known stress-based failure probability approach.

42 ENGINEERING↗
DOE OSTI2023

Experimental Study of the Invariance of Pressure Gain with Respect to the Dynamics of Multiple Competing Waves in a Rotating Detonation Combustor

Changes in the overall performance of a rotating detonation combustor with respect to changes in operation mode and wave dynamics arising by operation with fixed inlet/exit geometry but at different combustor, lengths are investigated experimentally. The air inlet, fuel injection, and exit constriction geometry are held constant while only the length of the detonation channel is varied from 71 to 137 mm (which corresponds to about 10 to 20 channel widths). Operation of H2/air over a range of air mass flow rates and equivalence ratios are considered for every chamber length. The number and speed of (primary) detonation and secondary waves are characterized through high-speed pressure measurements in the detonation channel and aft chemiluminescence videos. The number of waves is found to increase with length while detonation wave speed decreases significantly. Particular emphasis is given to characterize a phenomenon that is observed at operation with longer combustor lengths and higher mass flow rates. The phenomenon manifests as a super-cycle behavior with a period equal to many detonation wave rotational periods and is characterized by a periodic and structured ascending/descending sequence of the number, speed, and direction of both (primary) detonation and secondary waves. This phenomenon is likely a manifestation of the system failing in achieving operation with a higher number of detonation waves as length and/or mass flow rate are increased. The performance of the device is quantified in terms of measured thrust and pressure gain (through the use of the equivalent available pressure). Both metrics are essentially found to be invariant with respect to combustor length and most importantly, mode of operation. Surprisingly, even operation with complex wave dynamics arising from transitions between multiple competing wave systems does not appear to alter the overall global performance of the device but rather, it remains defined by the total (capture) air mass flow rate, equivalence ratio, and inlet/outlet areas.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Understanding the effect of irradiation and silicon carbide microstructure on silver diffusion in TRISO particles

The silicon carbide (SiC) layer in tristructural isotropic (TRISO) fuel particles serves as a barrier to prevent the escape of fission from the fuel kernel. The release of silver (Ag) is a concern due to the long half-life of the 110mAg isotope. In this study, a combination of atomistic and phase-field methods focuses on quantifying the effect of irradiation and SiC microstructure on Ag diffusion. Atomistic calculations provide the Ag diffusivity in SiC bulk and GBs, also providing an estimate of the effect of irradiation defects on Ag diffusivity in bulk SiC. These lower length scale efforts are leveraged to develop a mesoscale effective Ag diffusion coefficient (Deff) in SiC. Deff is defined as a function of temperature, microstructure variables, and fluence. Deff is implemented in the fuel performance code Bison to predict Ag release from AGR-1 and AGR-2 TRISO fuel particles. We hereby quantify the impact of SiC grain size and irradiation on Ag release and improve Bison's predictions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Sectioning of NBG-17 Graphite Billet

The Advanced Reactor Technologies (ART) Baseline Graphite Characterization program at the Idaho National Laboratory (INL) is performing a comprehensive evaluation of inter-billet variations in as-produced nuclear-grade graphite. Before graphite test specimens are machined, the full-size billets must be pre-sectioned into sub-blocks that can be more easily handled and shipped. As manufactured, NBG-17 billets are rectangular in shape, nearly 6 feet in length, and may exceed 1,500 pounds in weight. Sectioning of these billets must be accomplished via a supplier that is capable of handling and cutting the billets into individual slabs and quartering these slabs into sub-blocks. Billets will be pre-labeled by the Purchaser prior to leaving controlled storage such that traceability of any individual sub-block is never lost during sectioning operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2007

Development of Advanced Stirling Radioisotope Generator for Space Exploration

Under the joint sponsorship of the Department of Energy and NASA, a radioisotope power system utilizing Stirling power conversion technology is being developed for potential future space missions. The higher conversion efficiency of the Stirling cycle compared with that of Radioisotope Thermoelectric Generators (RTGs) used in previous missions (Viking, Pioneer, Voyager, Galileo, Ulysses, Cassini, and New Horizons) offers the advantage of a four-fold reduction in PuO2 fuel, thereby saving cost and reducing radiation exposure to support personnel. With the advancement of state-of-the-art Stirling technology development under the NASA Research Announcement (NRA) project, the Stirling Radioisotope Generator program has evolved to incorporate the advanced Stirling convertor (ASC), provided by Sunpower, into an engineering unit. Due to the reduced envelope and lighter mass of the ASC compared to the previous Stirling convertor, the specific power of the flight generator is projected to increase from 3.5 to 7 We/kg, along with a 25 percent reduction in generator length. Modifications are being made to the ASC design to incorporate features for thermal, mechanical, and electrical integration with the engineering unit. These include the heat collector for hot end interface, cold-side flange for waste heat removal and structural attachment, and piston position sensor for ASC control and power factor correction. A single-fault tolerant, active power factor correction controller is used to synchronize the Stirling convertors, condition the electrical power from AC to DC, and to control the ASCs to maintain operation within temperature and piston stroke limits. Development activities at Sunpower and NASA Glenn Research Center (GRC) are also being conducted on the ASC to demonstrate the capability for long life, high reliability, and flight qualification needed for use in future missions.

Chan, Jack↗