Results for “hard spheres” — Page 9

NASA NTRS1989

Reflectance characteristics of reference materials used in lidar hard target calibration

Lidar hard target calibration is discussed, emphasizing the transfer target methodology. Characteristics of example calibratrion target surfaces are described in light of four reflectance mechanisms, specular, diffuse, retroreflection, and off-specular reflectance. The ideal transfer target is one which can be described as entirely diffusely reflecting, i.e., Lambertian. Correction for retroreflection is required when using the flowers of a sulfur transfer target at CO2 laser wavelengths. Corrections for specular and retroreflection for the integrating sphere are negligible; however, the off-specular reflectance of rough metal surfaces used in the integrating spheres is only qualitatively compared with the diffuse reflectance of flowers of sulfur.

Haner, David A.↗

NASA NTRS1963

The satellite ferrimagnetic power limiter

To limit the 4080-mc local oscillator signal power input to the beat oscillator modulator of the Telstar satellite communications repeater, a subsidiary absorption limiter was used which consisted of an optically polished sphere of single-crystal yttrium iron garnet (YIG), placed in a resonant transmission cavity between the amplified 4080-mc output of the traveling-wave tube and the BO modulator input. The limiter holds the output power nearly constant above a given input threshold; below this threshold the YIG is linear and introduces only a small loss. The threshold is determined, for a given sample at a given frequency, by the external magnetic bias field. Temperature compensation over the desired range was obtained by orienting the crystal with the dc magnetic field along a [100] or “hard” axis. The total weight of the limiter package, including the bias magnet and cavity, is 13 ounces.

YTTRIUM-IRON GARNET /YIG/ CRYSTAL↗

NASA NTRS1995

Resistance to Rolling in the Adhesive Contact of Two Elastic Spheres

For the stability of agglomerates of micron sized particles it is of considerable importance to study the effects of tangential forces on the contact of two particles. If the particles can slide or roll easily over each other, fractal structures of these agglomerates will not be stable. We use the description of contact forces by Johnson, Kendall and Roberts, along with arguments based on the atomic structure of the surfaces in contact, in order to calculate the resistance to rolling in such a contact. It is shown that the contact reacts elastically to torque forces up to a critical bending angle. Beyond that, irreversible rolling occurs. In the elastic regime, the moment opposing the attempt to roll is proportional to the bending angle and to the pull-off force P(sub c). Young's modulus of the involved materials has hardly any influence on the results. We show that agglomerates of sub-micron sized particles will in general be quite rigid and even long chains of particles cannot be bent easily. For very small particles, the contact will rather break than allow for rolling. We further discuss dynamic properties such as the possibility of vibrations in this degree of freedom and the typical amount of rolling during a collision of two particles.

Dominik, C.↗

NASA NTRS1995

Resistance to Rolling in the Adhesive Contact of Two Elastic Spheres

For the stability of agglomerates of micron sized particles it is of considerable importance to study the effects of tangential forces on the contact of two particles. If the particles can slide or roll easily over each other, fractal structures of these agglomerates will not be stable. We use the description of contact forces by Johnson, Kendall and Roberts, along with arguments based on the atomic structure of the surfaces in contact, in order to calculate the resistance to rolling in such a contact. It is shown that the contact reacts elastically to torque forces up to a critical bending angle. Beyond that, irreversible rolling occurs. In the elastic regime, the moment opposing the attempt to roll is proportional to the bending angle and to the pull-off force P(sub c). Young's modulus of the involved materials has hardly any influence on the results. We show that agglomerates of sub-micron sized particles will in general be quite rigid and even long chains of particles cannot be bent easily. For very small particles, the contact will rather break than allow for rolling. We further discuss dynamic properties such as the possibility of vibrations in this degree of freedom and the typical amount of rolling during a collision of two particles.

Dominik, C.↗

NASA NTRS2005

Surface Collisions Involving Particles and Moisture (SCIP'M)

Experiments were performed on the collision of a solid sphere with a nearly horizontal flat surface covered with a thin layer of viscous liquid. High-speed collisions were obtained by dropping the ball onto the surface from various heights, using gravitational acceleration. Low-speed collisions were obtained using pendulums with long strings or by launching the balls at low velocities in the reduced-gravity environment of parabolic flight. The sphere bounces only when the impact velocity exceeds a critical value. The coefficient of restitution (ratio of rebound velocity to impact velocity) increases with increasing impact velocity above the critical value, indicating the increasing relative importance of elastic deformation to viscous dissipation. The critical impact velocity increases, and the coefficient of restitution decreases, with increasing viscosity or thickness of the liquid layer and with decreasing density or size of the sphere. The ratio of the wet and dry coefficients is expressed as a function of the Stokes number (ratio of particle inertia and viscous forces), showing good agreement between theory and experiment. Similar experiments were performed with the flat surface inclined at various angles to the approaching sphere. A modified Stokes number, which is a measure of the ratio of inertia of the sphere in the normal direction to the viscous forces exerted by the fluid layer, was used for the analysis of oblique collisions. Even for these oblique collisions, it was found that no rebound of the ball was observed below a certain critical Stokes number. The coefficient of normal restitution, defined as a ratio of normal rebound velocity to normal approach velocity, was found to increase beyond the critical Stokes number and even out as it approaches the value for dry restitution at high Stokes numbers. It was also found that, for smooth spheres like steel, the normal restitution at the same modified Stokes number is independent of the angle of impact. The tangential coefficient of restitution, defined as the ratio of tangential rebound velocity to tangential approach velocity, is found to be nearly unity, except for very low approach velocities. Thus, as a first approximation, the theories that predict the coefficient of restitution for head-on wet collisions can be extended to predict the coefficient of normal restitution for oblique wet collisions. Additional experiments were performed with soft surfaces in which a porous cloth or sponge layer was placed over the hard, flat surface. In these experiments, the coefficient of restitution was found to decrease with increasing impact velocity, due to inelastic losses in the soft material. A model combining inelastic deformation and flow through porous media was developed to describe these findings.

Davis, Robert H.↗

NASA NTRS1976

The early light curve of A0620-00

The Ariel-5 All-Sky Monitor measured the 3-6 keV X-ray intensity of 0620-00 for two days shortly after peak emission in August 1975, and continuously throughout September 1975. The effective exposure each day for this source (and every other source in the 80% of the celestial sphere covered by the monitor) is approximately 250 sq cm sec. The light curve obtained through October 1 (when the spin axis was again pointed to A0620-00) is shown. The intensity difference at maximum is obviously a manifestation of the very soft spectrum of the source. Clearly, A0620-00 was approximately four times as bright as Sco X-1 at maximum in the band 3-6 keV. The decay is quite smooth, but cannot be fit with a single e-folding time. The interval between the early All-Sky Monitor points and the onset of continuous coverage has an inferred e-folding time of 22 days, but it is continually increasing throughout September. A0620-00 is apparently similar in its X-ray character to the very strong, long-lasting transient X-ray sources which presently number six. In contrast, only three can be sensibly reconciled with the lower-intensity, shorter-duration hard-spectrum transients which have been found to pulse on a time scale of minutes.

Kaluzienski, L. J.↗

NASA NTRS1995

Pair cascades in extragalactic jets. 1: Gamma rays

A model of the approximately 0.1-10 GeV gamma-ray jets observed by the EGRET instrument on the Compton Gamma Ray Observatory (CGRO) is developed. It is shown that the soft X-ray background in an active galactic nuclei (AGN) contributes an opacity to pair production and that a gamma-ray photosphere or 'gamma-sphere' can be defined whose radius increases with gamma-ray energy E(sub gamma). It is proposed that the observed gamma-ray emission is due to inverse Compton scattering of the ambient soft X-rays by relativistic pairs accelerated in situ by shock fronts in a relativistic jet. For a wide range of assumed physical conditions, the emission at a given E(sub gamma) originates from near the associated gamma-spheres; emission from below the gamma-sphere initiates a cascade down to the energy where the gamma-rays can escape freely. In this model, the slope of the emergent gamma-ray spectrum is determined by the scattered, soft X-ray spectrum and the variation of the particle acceleration rate with jet radius. In general it is expected that the variation in the gamma-ray flux will be either slower or later at higher energy. It is also shown that the efficiency of conversion of energy from injected high-energy pairs to 0.1-10 GeV gamma-rays is typically high so that the models are radiatively efficient. It is argued that the observed gamma-ray jets are likely to be particle-dominated, though magnetically confined. The gamma-ray spectrum should continue down to an energy approximately 5 MeV emitted from an annihilation radius within which the pair content of the jet is limited by annihilation. This is probably the site of the beamed hard X-ray emission. It is speculated that the relativistic jets associated with radio-loud AGNs are powered electromagnetically by a spinning black hole and that they are collimated by an encircling MHD wind leaving the accretion disk at a slower speed. Powerful FR2 radio sources are formed when the hole spins rapidly and the relativistic core accelerates the MHD sheath; low-power FR1 sources ensue when the opposite occurs. Finally, it is suggested that the key factor which determines whether or not a given active nucleus can form a jet and a radio to gamma-ray nonthermal continuum is the central density of mass-losing stars which, when large, precludes the formation of a super-Alfvenic, collimating wind.

Blandford, R. D.↗

NASA NTRS1998

Low Luminosity States of the Black Hole Candidate GX 339-4: ASCA and Simultaneous Radio/RXTE Observations - 1

We discuss a series of observations of the black hole candidate GX 339-4 in low luminosity, spectrally hard states. We present spectral analysis of three separate archival Advanced Satellite for Cosmology and Astrophysics (ASCA) data sets and eight separate Rossi X-ray Timing Explorer (RXTE) data sets. Three of the RXTE observations were strictly simultaneous with 843 Mega Hertz and 8.3-9.1 Giga Hertz radio observations. All of these observations have (3-9 keV) flux approximately less than 10(exp-9) ergs s(exp-1) CM(exp -2). The ASCA data show evidence for an approximately 6.4 keV Fe line with equivalent width approximately 40 eV, as well as evidence for a soft excess that is well-modeled by a power law plus a multicolor blackbody spectrum with peak temperature approximately equals 150-200 eV. The RXTE data sets also show evidence of an Fe line with equivalent widths approximately equal to 20-1OO eV. Reflection models show a hardening of the RXTE spectra with decreasing X-ray flux; however, these models do not exhibit evidence of a correlation between the photon index of the incident power law flux and the solid angle subtended by the reflector. 'Sphere+disk' Comptonization models and Advection Dominated Accretion Flow (ADAF) models also provide reasonable descriptions of the RXTE data. The former models yield coronal temperatures in the range 20-50 keV and optical depths of r approximately equal to 3. The model fits to the X-ray data, however, do not simultaneously explain the observed radio properties. The most likely source of the radio flux is synchrotron emission from an extended outflow of extent greater than O(10 (exp7) GM/c2).

Wilms, Joern↗

NASA NTRSDate not supplied

Wake Velocimetry of a Sphere-Cone Model in a Mach 10 Air Freestream using FLEET

Velocity measurements in the wake behind a sphere-cone-shaped vehicle wind tunnel model in a Mach 10 hypersonic air flow using femtosecond laser electronic excitation tagging (FLEET) are reported in this work. The FLEET measurements were performed at 1 kHz using a femtosecond laser centered at 800 nm and an ultrahigh-speed intensified camera system. The results reported here are for a single freestream condition corresponding to approximately Re ∞ /L = 3.6∙10 6 m -1 . The performance of the velocimetry instrument was evaluated in the quiescent test section at conditions relevant to the wake measurements. For velocity measurements in the wake, the FLEET measurement volume was translated to several radial locations from the model centerline in the vertical direction and at a streamwise location corresponding to approximately 12 mm from the payload. Reverse flow with mean velocities ranging from -12 m/s to -48 m/s were observed in the recirculating region of the wake, whereas hypersonic velocities in the range of 1079 m/s to 1183 m/s were observed in the free shear layer. A velocity uncertainty methodology is also outlined and applied for the reported measurements. The velocity data reported in this work is expected to play a significant role in the validation of computational codes modeling the hard-to-predict separated hypersonic wake.

FLEET↗

NASA NTRSDate not supplied

Wake Velocimetry of a Sphere-Cone Model in a Mach 10 Air Freestream using FLEET

Velocity measurements in the wake behind a sphere-cone-shaped vehicle wind tunnel model in a Mach 10 hypersonic air flow using femtosecond laser electronic excitation tagging (FLEET) are reported in this work. The FLEET measurements were performed at 1 kHz using a femtosecond laser centered at 800 nm and an ultrahigh-speed intensified camera system. The results reported here are for a single freestream condition corresponding to approximately Re ∞ /L = 3.6∙10 6 m -1 . The performance of the velocimetry instrument was evaluated in the quiescent test section at conditions relevant to the wake measurements. For velocity measurements in the wake, the FLEET measurement volume was translated to several radial locations from the model centerline in the vertical direction and at a streamwise location corresponding to approximately 12 mm from the payload. Reverse flow with mean velocities ranging from -12 m/s to -48 m/s were observed in the recirculating region of the wake, whereas hypersonic velocities in the range of 1079 m/s to 1183 m/s were observed in the free shear layer. A velocity uncertainty methodology is also outlined and applied for the reported measurements. The velocity data reported in this work is expected to play a significant role in the validation of computational codes modeling the hard-to-predict separated hypersonic wake.

FLEET↗

NASA NTRS2007

Human Space Exploration: The Moon, Mars, and Beyond

America is returning to the Moon in preparation for the first human footprint on Mars, guided by the U.S. Vision for Space Exploration. This presentation will discuss NASA's mission, the reasons for returning to the Moon and going to Mars, and how NASA will accomplish that mission in ways that promote leadership in space and economic expansion on the new frontier. The primary goals of the Vision for Space Exploration are to finish the International Space Station, retire the Space Shuttle, and build the new spacecraft needed, to return people to the Moon and go to Mars. The Vision commits NASA and the nation to an agenda of exploration that also includes robotic exploration and technology development, while building on lessons learned over 50 years of hard-won experience. Why the Moon? Many questions about the Moon's potential resources and how its history is linked to that of Earth were spurred by the brief Apollo explorations of the 1960s and 1970s. This new venture will carry more explorers to more diverse landing sites with more capable tools and equipment for extended expeditions. The Moon also will serve as a training ground before embarking on the longer, more difficult trip to Mars. NASA plans to build a lunar outpost at one of the lunar poles, learn to live off the land, and reduce dePendence on Earth for longer missions. America needs to extend its ability to survive in hostile environments close to our home planet before astronauts will reach Mars, a planet very much like Earth. NASA has worked with scientists to define lunar exploration goals and is addressing the opportunities for a range of scientific study on Mars. In order to reach the Moon and Mars within a lifetime and within budget, NASA is building on common hardware, shared knowledge, and unique experience derived from the Apollo Saturn, Space Shuttle and contemporary commercial launch vehicle programs. The journeys to the Moon and Mars will require a variety of vehicles, including the Ares I Crew Launch Vehicle, which transports the Orion Crew Exploration Vehicle, and the Ares V Cargo Launch Vehicle, which transports the Lunar Surface Access Module. The architecture for the lunar missions will use one launch to ferry the crew into orbit, where it will rendezvous with the Lunar Module in the Earth Departure Stage, which will then propel the combination into lunar orbit. The imperative to explore space with the combination of astronauts and robots will be the impetus for inventions such as solar power and water and waste recycling. This next chapter in NASA's history promises to write the next chapter in American history, as well. It will require this nation to provide the talent to develop tools, machines, materials, processes, technologies, and capabilities that can benefit nearly all aspects of life on Earth. Roles and responsibilities are shared between a nationwide Government and industry team. The Exploration Launch Projects Office at the Marshall Space Flight Center manages the design, development, testing, and evaluation of both vehicles and serves as lead systems integrator. A little over a year after it was chartered, the Exploration Launch Projects team is testing engine components, refining vehicle designs, performing wind tunnel tests, and building hardware for the first flight test of Ares I-l, scheduled for spring 2009. The U.S. Vision for Space Exploration lays out a roadmap for a long-term venture of discovery. This endeavor will inspire and attract the best and brightest students to power this nation successfully to the Moon, Mars, and beyond. If one equates the value proposition for space with simple dollars and cents, the potential of the new space economy is tremendous, from orbital space delivery services for the International Space Station to mining and solar energy collection on the Moon and asteroids. The Vision for Space Exploration is fundamentally about bringing the resources of the solar system within the economic sphere of humaind. Given the immense size of our solar system, the amount of available material and energy within it present an enormous economic opportunity.

Sexton, Jeffrey D.↗