Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Effect of Li 2 O on the microstructure, magnetic and transport properties of Tl-2223 superconductor

Here, the present study gives an account of the effect of addition of Li 2 O on the ease of phase formation and superconducting properties of Tl 2 Ba 2 Ca 2 Cu 3 O 10 + δ (Tl-2223) material. Li 2 O slightly decreases the superconducting transition temperature, while an optimal concentration of 20% Li 2 O improves the critical current density (J c ) by about two fold. We also found substantial effects on the synthesis temperature, microstructure and normal state transport properties of Tl-2223 with Li 2 O addition. Short-time annealing under flowing Ar + 4%H 2 (1 h) further improves the superconducting volume fractions, as well as J c .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Sr effect on the microstructure and tensile properties of A357 aluminum alloy and Al{sub 2}O{sub 3}/SiC-A357 cast composites

The effect of strontium as a modifier on the microstructures and tensile properties of two castable particulate metal matrix composites has been studied. The particulate metal matrix composites had similar matrix alloy (A357) but different reinforcing fine particles (silicon carbide and alumina). Results showed that the addition of 0.03% strontium makes a modest improvement to the yield strength, ultimate tensile strength and elongation percentage values, and the scatter of these properties, but makes a significant improvement to minimum strength and elongation results. Microstructural examinations by scanning electron microscope and energy dispersive spectroscopy analysis of metal matrix composites showed segregation of strontium on both the silicon carbide and alumina particles. Further results showed that the addition of higher strontium levels contributes to the over-modification of the eutectic silicon and promotes the formation of an Al-Si-Sr intermetallic compound on the particle/matrix interface.

36 MATERIALS SCIENCE↗

Effect of Deformation Parameters on Microstructure and Properties During DIFT of X70HD Pipeline Steel

Grain refinement is a critical approach to improve the strength of materials without damaging the toughness. The grains of deformation-induced ferrite are considerably smaller than those of proeutectoid ferrite. Grain refinement is crucial to the application of deformation-induced ferrite. The composition of ferrite and bainite or martensite is important in controlling the performance of X70HD pipeline steel, and cooling significantly influences the control of their ratio and grain size. By analyzing the static and dynamic phase-transition points using Gleeble-3800 thermal simulator, thermal simulations were performed through two-stage deformations in the austenite zone. Ferrite transformation rules were studied with thermal simulation tests under different deformation and cooling parameters based on the actual production of cumulative deformation. The influence of deformation parameters on the microstructure transformation was analyzed. Numerous fine-grain deformation-induced ferrites were obtained by regulating various parameters, including deformation temperature, strain rate, cooling rate, final cooling temperature and other parameters. Results of metallographic observation and microtensile testing revealed that the selection of appropriate parameters can refine the grains and improve the performance of the X70HD pipeline steel.

36 MATERIALS SCIENCE↗

Evaluation of microstructure anisotropy on room and medium temperature ECAP deformed F138 steel

The microstructure developed during severe plastic deformation results in improved mechanical properties because of the decrease in domain sizes and accumulation of defects, mainly dislocation arrays. The characteristic deformation stages observed in low stacking fault energy (SFE) face centered cubic (FCC) materials are highly influenced by the development of the primary and secondary twinning that compete with dislocation glide. In this paper, a low SFE F138 stainless steel is deformed by equal channel angular pressing (ECAP) up to 4 passes at room temperature (RT) and at 300 °C to compare the grain refinement and twin boundary development with increasing deformation. Tensile tests were performed to determine the deformation stages reached by the material before and after ECAP deformation, and the resulting microstructure was observed by TEM. X-ray diffraction and EBSD, average technique the first and local the second one, were used to quantify the microstructural changes, allowing the determination of diffraction domain sizes, dislocation and stacking fault densities and misorientation indices, which lead to a complete analysis of the deformation introduced in the material, with comparative correlations between various microstructural parameters. - Highlights: • The microstructure of ECAP pressed F138 steel was studied using TEM, EBSD and XRD. • Increasing deformation reduced domain sizes and increased dislocation densities. • Dislocation array compactness and misorientation increased with higher deformation. • Largest dislocation densities, mostly screw, match with simultaneous activation of twins. • Several correlations among microstructural features and parameters have been disclosed.

36 MATERIALS SCIENCE↗

Dissipation of radiation energy in concentrated solid-solution alloys: Unique defect properties and microstructural evolution

The effort to develop metallic alloys with increased structural strength and improved radiation performance has focused on the incorporation of either solute elements or microstructural inhomogeneities to mitigate damage. The recent discovery and development of single-phase concentrated solid-solution alloys (SP-CSAs) has prompted fundamental questions that challenge established theories and models currently applicable to conventional alloys. Here, the current understanding of electronic and atomic effects, defect evolution, and microstructure progression suggests that radiation energy dissipates in SP-CSAs at different interaction strengths via energy carriers (electrons, phonons, and magnons). Modification of electronic- and atomic-level heterogeneities and tailoring of atomic transport processes can be realized through tuning of the chemical complexity of SP-CSAs by the selection of appropriate elements and their concentrations. Fundamental understanding of controlling energy dissipation via site-to-site chemical complexity reveals new design principles for predictive discovery and guided synthesis of new alloys with targeted functionalities, including radiation tolerance.

36 MATERIALS SCIENCE↗

The induction of a graphite-like phase on diamond films by a Fe-coating/post-annealing process to improve their electron field emission properties

The electron field emission (EFE) process for diamond films was tremendously enhanced by Fe-coating and post-annealing processes. Microstructural analysis indicates that the mechanism for the improvement in the EFE process is the formation of nanographites with good crystallinity that surround the Fe (or Fe{sub 3}C) nanoclusters. Presumably the nanographites were formed via the reaction of Fe clusters with diamond films, viz. by the dissolution of carbons into Fe (or Fe{sub 3}C) clusters and the reprecipitation of carbon species to the surface of the clusters, a process similar to the growth of carbon nanotubes via Fe clusters as catalyst. Not only is a sufficiently high post-annealing temperature (900 deg. C) required but also a highly active reducing atmosphere (NH{sub 3}) is needed to give a proper microstructure for enhancing the EFE process. The best EFE properties are obtained by post-annealing the Fe-coated diamond films at 900 deg. C in an NH{sub 3} environment for 5 min. The EFE behavior of the films can be turned on at E{sub 0} = 1.9 V/{mu}m, attaining a large EFE current density of 315 {mu}A/cm{sup 2} at an applied field of 8.8 V/{mu}m (extrapolation using the Fowler-Nordheim model leads to J{sub e} = 40.7 mA/cm{sup 2} at a 20 V/{mu}m applied field).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Refinement effect of two rare earth borides in an Al-7Si-4Cu alloy: A comparative study

Highlights: • Refinement performance of Al-La-B and Al-Ce-B refiners in Al-7Si-4Cu alloy was investigated. Due to the orientation relationships between rare earth borides and Al, CeB{sub 6} and LaB{sub 6} can act as the nucleation substrate of α-Al and refine Al-Si-Cu casting alloy effectively. • Al-Ce-B refiner showed better refining efficacy than Al-La-B refiner because of the lower lattice mismatch and less angel difference of the certain orientation relationship between CeB{sub 6} and Al, demonstrated by TEM analysis. • Effects of Al-La-B and Al-Ce-B refiners on alloy defects and tensile properties were investigated. The best refiner addition level in this alloy is considered to be 1.0wt%. Tensile properties of Al-7Si-4Cu alloy were prominently improved owing to the better refined microstructures and much fewer shrinkage defects. - Abstract: In this paper, refinement performance of Al-La-B and Al-Ce-B refiners in Al-7Si-4Cu alloy and their effects on alloy defects and tensile properties were investigated. Due to the orientation relationships between rare earth borides and Al, CeB{sub 6} and LaB{sub 6} can act as the nucleation substrate of α-Al and refine Al-Si-Cu casting alloy effectively. Al-Ce-B refiner showed better refining efficacy than Al-La-B refiner because of the lower lattice mismatch and less angel difference of the certain orientation relationship between CeB{sub 6} and Al, demonstrated by TEM analysis. Tensile properties of Al-7Si-4Cu alloy were prominently improved from 204.4 ± 5.9 MPa to 250.6 ± 6.7 MPa in as-cast state and 335.7 ± 6.5 MPa to 386.0 ± 7.0 MPa in heat treatment state owing to the better refined microstructures and much fewer shrinkage defects. However, when the addition level of the refiners was higher than 1.0 wt%, the amount of gas pores in the alloy significantly increased. Hence, the best refiner addition level in this alloy is considered to be 1.0 wt%.

36 MATERIALS SCIENCE↗

Graphene reinforced UHMWPE fibers

Thermoplastic polymers are increasingly used in electric vehicles, hydrogen fuel cell vehicles, and other decarbonization applications due to their lightweight and formability. Higher-strength polymers are needed to supplant metals in the vehicle structure, thereby reducing mass and improving efficiency. Ultra-high molecular weight polyethylene (UHMWPE) fibers possess one of the highest strength-to-weight ratios of technical polymers, and further improvement via reinforcement by nanofillers, such as graphene, will expand their performance envelope. Here, in this work, UHMWPE/graphene nanocomposite fibers were gel spun and characterized for their morphological, microstructural, thermal, and mechanical properties. The addition of a low fraction of graphene improved the tensile strength of the fibers by 25% and tensile modulus by 32%. Differential scanning calorimetry showed an increase in melting temperature and degree of crystallinity, which indicates improved coordination of the molecular chains induced by the addition of graphene. The reinforcement also affected the cross-sectional shape of the fibers; the aspect ratio of the fibers’ elliptical shape declined with increasing graphene content showing the skeletal effect of the graphene nanofillers in the polymer matrix. The reinforcing effect of graphene declined above a threshold concentration, and theoretical modeling was applied to demonstrate that increased agglomerates led to reduced properties. This work demonstrates a simple, effective method to produce graphene-reinforced UHMWPE fibers and lays a foundation for understanding the potential for leveraging graphene to form ultra-high-performance nanocomposite fibers for myriad engineering applications.

36 MATERIALS SCIENCE↗

Advanced Constituents and Processes for Ceramic Composite Engine Components

The successful replacement of metal alloys by ceramic matrix composites (CMC) in hot-section engine components will depend strongly on optimizing the processes and properties of the CMC microstructural constituents so that they can synergistically provide the total CMC system with improved temperature capability and with the key properties required by the components for long-term structural service. This presentation provides the results of recent activities at NASA aimed at developing advanced silicon carbide (Sic) fiber-reinforced hybrid Sic matrix composite systems that can operate under mechanical loading and oxidizing conditions for hundreds of hours at 2400 and 2600 F, temperatures well above current metal capability. These SiC/SiC composite systems are lightweight (-30% metal density) and, in comparison to monolithic ceramics and carbon fiber-reinforced ceramic composites, are able to reliably retain their structural properties for long times under aggressive engine environments. It is shown that the improved temperature capability of the SiC/SiC systems is related first to the NASA development of the Sylramic-iBN Sic fiber, which displays high thermal stability, creep resistance, rupture resistance, and thermal conductivity, and possesses an in-situ grown BN surface layer for added environmental durability. This fiber is simply derived from Sylramic Sic fiber type that is currently produced at ATK COI Ceramics. Further capability is then derived by using chemical vapor infiltration (CVI) to form the initial portion of the hybrid Sic matrix. Because of its high creep resistance and thermal conductivity, the CVI Sic matrix is a required base constituent for all the high temperature SiC/SiC systems. By subsequently thermo- mechanical-treating the CMC preform, which consists of the S ylramic-iBN fibers and CVI Sic matrix, process-related defects in the matrix are removed, further improving matrix and CMC creep resistance and conductivity.

Yun, H. M.↗

Low temperature aluminum nitride thin films for sensory applications

A low-temperature sputter deposition process for the synthesis of aluminum nitride (AlN) thin films that is attractive for applications with a limited temperature budget is presented. Influence of the reactive gas concentration, plasma treatment of the nucleation surface and film thickness on the microstructural, piezoelectric and dielectric properties of AlN is investigated. An improved crystal quality with respect to the increased film thickness was observed; where full width at half maximum (FWHM) of the AlN films decreased from 2.88 ± 0.16° down to 1.25 ± 0.07° and the effective longitudinal piezoelectric coefficient (d{sub 33,f}) increased from 2.30 ± 0.32 pm/V up to 5.57 ± 0.34 pm/V for film thicknesses in the range of 30 nm to 2 μm. Dielectric loss angle (tan δ) decreased from 0.626% ± 0.005% to 0.025% ± 0.011% for the same thickness range. The average relative permittivity (ε{sub r}) was calculated as 10.4 ± 0.05. An almost constant transversal piezoelectric coefficient (|e{sub 31,f}|) of 1.39 ± 0.01 C/m{sup 2} was measured for samples in the range of 0.5 μm to 2 μm. Transmission electron microscopy (TEM) investigations performed on thin (100 nm) and thick (1.6 μm) films revealed an (002) oriented AlN nucleation and growth starting directly from the AlN-Pt interface independent of the film thickness and exhibit comparable quality with the state-of-the-art AlN thin films sputtered at much higher substrate temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Different Thermomechanical Processes on the Microstructure, Texture, and Mechanical Properties of API 5L X70 Steel

A commercial API 5L X70 steel plate was subjected to different thermomechanical processes to propose a novel thermomechanical rolling path to achieve improved mechanical properties. Scanning electron microscopy, electron backscatter diffraction, and x-ray texture analysis were employed for microstructural characterization. The results showed that strain-free recrystallized {001} ferrite grains that developed at higher rolling temperature could not meet the American Petroleum Institute (API) requirements. Also, refined and work-hardened grains that have formed in the intercritical region with high stored energy do not provide suitable tensile properties. However, fine martensite–austenite constituents dispersed in ferrite matrix with grains having predominantly {111} and {110} orientations parallel to the normal direction that developed under isothermal rolling at 850 °C provided an outstanding combination of tensile strength and ductility.

36 MATERIALS SCIENCE↗

Effect of microstructure and composition on the improvement of n-type SiGe/GaP material

Experimental and theoretical work has been conducted at the Jet Propulsion Laboratory to improve the thermoelectric properties of n-type SiGe materials. Particular emphasis has been placed upon the understanding of the differences in dopant solid solubilities when multidoping with both Ga and P instead of P alone, as in standard SiGe alloys. A set of various experimental techniques for obtaining heavily doped hot-pressed samples coupled with thermodynamic theoretical considerations was used to relate microstructure and composition to electrical and thermal transport properties. Application of these results to high-temperature heat treatments of several SiGe/GaP samples achieved substantial improvements of the thermoelectric figure of merit Z, with average values close to 1 x 10-3K-1 over the 600-1000 C temperature range. A set of systematic anneals on heavily doped SiGe/GaP materials is reported in an attempt to consistently reproduce the optimized thermoelectric properties.

Fleurial, Jean-Pierre↗

MC Carbide Characterization in High Refractory Content Powder-Processed Ni-Based Superalloys

Carbide precipitates in Ni-based superalloys are considered to be desirable phases that can contribute to improving high-temperature properties as well as aid in microstructural refinement of the material; however, they can also serve as crack initiation sites during fatigue. To date, most of the knowledge pertaining to carbide formation has originated from assessments of cast and wrought Ni-based superalloys. As powder-processed Ni-based superalloys are becoming increasingly widespread, understanding the different mechanisms by which they form becomes increasingly important. Detailed characterization of MC carbides present in two experimental high Nb-content powder-processed Ni-based superalloys revealed that Hf additions affect the resultant carbide morphologies. This morphology difference was attributed to a higher magnitude of elastic strain energy along the interface associated with Hf being soluble in the MC carbide lattice. The composition of the MC carbides was studied through atom probe tomography and consisted of a complex carbonitride core, which was rich in Nb and with slight Hf segregation, surrounded by an Nb carbide shell. The characterization results of the segregation behavior of Hf in the MC carbides and the subsequent influence on their morphology were compared to density functional theory calculations and found to be in good agreement, suggesting that computational modeling can successfully be used to tailor carbide features.

Materials Science↗

Manufacturing ODS Steels from GARS Powders by Friction Consolidation and Extrusion

Previous research suggested that friction-based processing is a promising method for fabricating oxide dispersion-strengthened (ODS) steel. In this study, we combined friction consolidation and friction extrusion to successfully manufacture ODS steel rods using precursor powder made with gas atomization reaction synthesis. We examined the microstructure evolution from the initial powder to the final extruded rod, which revealed the dispersion process of Y. Additionally, by comparing the microstructures of three rods extruded at different temperatures, we showed that low-temperature friction extrusion effectively enhanced microstructure uniformity and prevented grain coarsening, leading to improved mechanical properties. Furthermore, our findings provide practical guidelines for adjusting processing parameters in the production of ODS steel using friction-based processing.

36 MATERIALS SCIENCE↗

Effect of intermediate annealing time on microstructure, texture and mechanical properties of Al-Mg-Si-Cu alloy

Highlights: • Long intermediate annealing time could be beneficial to the improvement of deep drawability. • Long intermediate annealing time could give rise to more particles with a larger average size. • As intermediate annealing time increases, strength will change and it has no positive correlation with annealing time, • A particle dissolution model is proposed to illustrate the variation of the strengths with intermediate annealing time. - Abstract: The effect of intermediate annealing time on the microstructure, texture and mechanical properties of Al-Mg-Si-Cu alloys was studied by mechanical properties, microstructure and texture characterization in the present study. The results show that the intermediate annealing time has some influence on the microstructure, recrystallization texture, and final mechanical properties. After the pre-aging treatment and natural aging treatment (T4P treatment), in contrast to the sheet with short intermediate annealing time, the sheet with long intermediate annealing time possesses higher plastic strain ratio r value. Strength has no positive correlation with annealing time, and when applying the annealing time of 16 h, the strength is highest. Before solution treatment, the sheet with long intermediate annealing time has more particles with a larger average size, compared with the sheet with short intermediate annealing time. After solution treatment, they possess the similar recrystallization equiaxed grain structure and recrystallization texture. The sheet with short intermediate annealing time is comprised of Cube{sub ND} {001} <310>, Goss {110}<001> and P {011}<122> orientations, while the sheet with long intermediate annealing time possesses weak texture including Cube{sub ND} {001}<310>, Goss {110}<001> and {015}<751> orientations. Finally, a particle dissolution model during solution treatment is proposed to explain the variation of strength with annealing time.

36 MATERIALS SCIENCE↗

Effect of trace amounts of added Sc on microstructure and mechanical properties of 2055 aluminum alloy

Highlights: • Effect of trace Sc on microstructure and mechanical properties in 2055 Al-alloy was investigated. • T{sub 1} is the main strengthening phase in Sc free and Sc added 2055 alloy at the aging temperature of 175°C and 200°C. • The refinement of T{sub 1} by Sc addition depends on the aging temperature. • Mechanical properties were deteriorated by Sc at the aging temperature of 175°C and improved at 200°C aging treatment. - Abstract: The effects of Sc additions and isothermal aging on the microstructure and mechanical properties of 2055 aluminum alloy have been investigated. The isothermal aging temperatures investigated were 175 °C and 200 °C. Results show that the aging temperature does not affect the type of precipitates in both Sc-free and Sc-added 2055 Al alloys. While remarkable changes in the size and number density of T{sub 1} (Al{sub 2}CuLi) precipitates have been observed. For samples aged at 175 °C for 8 h, the average length of T{sub 1} precipitates was increased from 39.9 nm to 45.6 nm, the number density decreased from 5.77 × 10{sup 22} m{sup −3} to 3.68 × 10{sup 22} m{sup −3} after Sc addition. On the contrary, when samples were aged at 200 °C for 8 h, the length decreased from 59.89 nm to 43.32 nm and number density increased from 2.13 × 10{sup 22} m{sup −3} to 3.00 × 10{sup 22} m{sup −3} by adding trace Sc. Slight deterioration of tensile strength and yield strength with higher ductility was founded at the aging temperature of 175 °C for 8 h due to the larger size and lower number density of T{sub 1} precipitates along with the formation of a W (AlCuSc) phase during the casting or homogenization processes. When aging temperature increased to 200 °C, tensile strength and yield strength were significantly improved by Sc addition without losing ductility. Highly dense fine T{sub 1} precipitates take responsible for the strength improvement, and to some extent it compensated the strength loss caused by the formation of W phase. A “vacancy-prison” mechanism was adopted to explain the effect of Sc additions on the precipitation of T{sub 1} phase as a function of aging temperature.

36 MATERIALS SCIENCE↗

Atomistic Simulations in Support of UO{sub 2} Fuel Performance Modeling

Large fission gas atoms such as Xe have very low solubility in the UO{sub 2} fuel matrix, which drives precipitation and growth of intra-granular fission gas bubbles, segregation of gas atoms to grain boundaries and evolution of intergranular bubbles. The inter-granular bubbles develop percolation networks leading to release of the fission gas. Fission gas bubbles induce fuel swelling and the fuel thermal conductivity is reduced by both fission gas bubbles and dispersed gas atoms. When fission gas is released from the fuel to the plenum, the pressure on the clad walls increases and the gap thermal conductivity decreases. All of these detrimentally affect fuel performance. The thermal conductivity of UO{sub 2} is low across a wide temperature range compared to iso-structural materials such as ThO{sub 2}, which is caused by the coupling between phonons carrying heat and uranium spins or magnetism providing a scattering mechanism with very low mean free path. For in-pile conditions the thermal conductivity is further reduced due to, for example, radiation damage, generation of fission products and fission gases and fuel microstructure evolution. This results in a complex burn-up dependent thermal conductivity. Thermal conductivity and fission gas evolution are two of the most important properties determining UO{sub 2} nuclear fuel performance. Both properties have significant uncertainty. In order to reduce this uncertainty, new models are being developed based on multi-scale simulations that attempt to improve the description of material properties and also couple them to the microstructure state of the material. In this paper we highlight atomistic calculations and simulations used to develop meso-scale models of the evolution of fission gases and thermal conductivity in UO{sub 2}. Literature examples of the application of these results and the corresponding models to fuel performance simulations will also be given. (author)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

On the strength and fracture toughness of an additive manufactured CrCoNi medium-entropy alloy

An additively manufactured (nominally equiatomic) CrCoNi alloy was processed by laser powder bed fusion (LPBF). At ambient temperatures (298 K), this medium-entropy alloy displayed a yield strength, σ y of ~691 ± 9 MPa, and an ultimate tensile strength, σ u of ~926 ± 15.2 MPa; at cryogenic temperatures (77 K), yield and tensile strengths increased respectively to σ y ~ 944 ± 6 MPa and σ u ~ 1382 ± 11 MPa. These strength levels are 57 and 44% higher than that of the wrought alloy, due to strengthening from the solidification cellular structures intertwined with dislocations in the LPBF CrCoNi. The crack-initiation fracture toughness, K JIc was measured to be ~183.7 ± 28 MPa√m at 298 K; this value marginally decreased by ~4% to ~176 ± 11 MPa√m at 77 K. These K JIc values of the LPBF CrCoNi were 11% and 35% lower than the wrought CrCoNi alloy at 298 K and 77 K, respectively. Here, the resistance to crack growth of the LPBF CrCoNi from its hierarchical micro- and meso-structures was evaluated using nonlinear-elastic fracture mechanics by measuring R-curve behavior in the form of the J-integral as a function of crack extension. The specific features of the hierarchical microstructures at different length-scales provide a basis for the strengthening and toughening properties of this additively manufactured medium-entropy alloy. This correlation between the deformation and the hierarchical microstructures at different length-scales may provide future guidance for improving the fracture toughness properties of medium-entropy alloys.

36 MATERIALS SCIENCE↗