Search NASA⌕ Search

SEARCH · Search NASA

Results for “insertion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Structural and electrophysical properties of In{sub 0.52}Al{sub 0.48}As/In{sub 0.53}Ga{sub 0.47}As/In{sub 0.52}Al{sub 0.48}As/InP HEMT nanoheterostructures with different combinations of InAs and GaAs inserts in quantum well

A complex investigation of structural and electrical properties of In{sub 0.52}Al{sub 0.48}As/In{sub y}Ga{sub 1−y}As/In{sub 0.52}Al{sub 0.48}As nanoheterostructures on InP substrates containing thin InAs and GaAs inserts in a quantum well (QW) has been performed. The GaAs nanolayers are grown at the QW boundaries between InGaAs and InAlAs layers, while the double InAs inserts are grown in InGaAs layers symmetrically with respect to the QW center. The layer and interface structures have been studied by transmission electron microscopy. It is shown that, when using the proposed epitaxial growth conditions, the introduction of ∼1.2-nm-thick InAs nanoinserts into the InGaAs QW and a ∼1-nm-thick GaAs nanobarrier at the QW boundaries does not induce structural defects. The diffusion of the InAlAs/InGaAs interface (2–3 monolayers) and InAs/InGaAs nanoinsert interface (1–2 monolayers) has been estimated. Measured Hall mobilities and electron concentrations in structures with different combinations of InAs and GaAs inserts have been analyzed using calculated energy band diagrams and electron density distributions. It is found that the photoluminescence spectra of the structures under study have differences caused by specific structural features of coupled QWs (specifically, the change in the In molar fraction due to InAs inserts and the change in the QW thickness due to GaAs transition barriers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Final technical report for: Insertional Mutagenesis of Brachypodium distachyon DE-AI02-07ER64452

Several bioenergy grasses are poised to become a major source of energy in the United States. Despite their increasing importance, we know little about the basic biology underlying the traits that control the utility of grasses as energy crops. Better knowledge of grass biology (e.g. identification of the genes that control cell wall composition, plant architecture, cell size, cell division, reproduction, nutrient uptake, carbon flux, etc.) could be used to design rational strategies for crop improvement and shorten the time required to domesticate these species. The use of an appropriate model system is an efficient way to gain this knowledge. Brachypodium distachyon is a small annual grass with all the attributes needed to be a modern model organism including simple growth requirements, fast generation time, small stature, small genome size and self-fertility. These attributes led to the recommendation in the DOE’s “Breaking the Biological Barriers to Cellulosic Ethanol: A Joint Research Agenda” report to propose developing and using B. distachyon as a model for energy crops to accelerate their domestication. Strategic investments (e.g. genome sequencing) in B. distachyon by the DOE are now bearing fruit and B. distachyon is being used as a model grass by hundreds of laboratories worldwide. Sequence indexed insertional mutants are an extremely powerful tool for both forward and reverse genetics. They allow researchers to order mutants in any gene tagged in the collection by simply emailing a request. The goal of this project was to create a collection of sequence indexed insertional mutants (T-DNA lines) for the model grass Brachypodium distachyon in order to facilitate research by the scientific community. During the course of this grant we created a collection of 23,649 B. distachyon T-DNA lines and identified 26,112 unique insertion sites. The collection can be queried through the project website (http://jgi.doe.gov/our-science/science-programs/plant-genomics/brachypodium/brachypodium-t-dna-collection/) and through the Phytozome genome browser (http://phytozome.jgi.doe.gov/pz/portal.html). The collection has been heavily utilized by the research community and, as of October 23, 2015, 223 orders for 12,069 seeds packets have been filled. In addition to creating this resource, we also optimized methods for transformation and sequencing DNA flanking insertion sites.

09 BIOMASS FUELS↗

Strength Ranking of Hard-Alloy Cutting Inserts of Different Shape

The stress–strain state of replaceable polyhedral inserts in composite tools is calculated by the finite-element method. The influence of the insert’s design parameter, the basing and attachment configuration, and the load on the stress and strain is established. Besides the strength of the inserts, attention is paid to the positional accuracy in the tool housing. Cutting inserts of maximum strength have been developed and patented.

42 ENGINEERING↗

Threaded insert for compact cryogenic-capable pressure vessels

An insert for a cryogenic capable pressure vessel for storage of hydrogen or other cryogenic gases at high pressure. The insert provides the interface between a tank and internal and external components of the tank system. The insert can be used with tanks with any or all combinations of cryogenic, high pressure, and highly diffusive fluids. The insert can be threaded into the neck of a tank with an inner liner. The threads withstand the majority of the stress when the fluid inside the tank that is under pressure.

08 HYDROGEN↗

Bulkhead insert for an internal combustion engine

An engine includes a cylinder block defining at least one main bearing bulkhead adjacent to a cylinder, and a crankshaft rotatably housed within the block by a main bearing. A bulkhead insert has a cap portion, and an insert portion provided within the bulkhead. The insert portion has having first and second end regions connected by first and second straps. Each strap having a flanged beam cross section. The first and second ends of the insert portion are configured to connect a main bearing cap column to a cylinder head column. Each of the first and second end regions define at least one protrusion having a surface substantially normal to engine combustion and reactive loads. The cap portion is configured to mate with the first end region at the main bearing cap column and support the main bearing.

33 ADVANCED PROPULSION SYSTEMS↗

High aspect ratio catalytic reactor and catalyst inserts therefor

The present invention relates to high efficient tubular catalytic steam reforming reactor configured from about 0.2 inch to about 2 inch inside diameter high temperature metal alloy tube or pipe and loaded with a plurality of rolled catalyst inserts comprising metallic monoliths. The catalyst insert substrate is formed from a single metal foil without a central supporting structure in the form of a spiral monolith. The single metal foil is treated to have 3-dimensional surface features that provide mechanical support and establish open gas channels between each of the rolled layers. This unique geometry accelerates gas mixing and heat transfer and provides a high catalytic active surface area. The small diameter, high aspect ratio tubular catalytic steam reforming reactors loaded with rolled catalyst inserts can be arranged in a multi-pass non-vertical parallel configuration thermally coupled with a heat source to carry out steam reforming of hydrocarbon-containing feeds. The rolled catalyst inserts are self-supported on the reactor wall and enable efficient heat transfer from the reactor wall to the reactor interior, and lower pressure drop than known particulate catalysts. The heat source can be oxygen transport membrane reactors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Apparent Monte Carlo Source Convergence Problem with BWR Fuel Depleted with Partial Control Blade Insertion

Oak Ridge National Laboratory (ORNL) and the US Nuclear Regulatory Commission (NRC) have initiated a multiyear project to investigate application of burnup credit (BUC) to boiling-water reactor (BWR) fuel in storage and transportation casks and spent fuel pools (SFPs). Ideally, a single combination of all operating parameters including moderator density and axial burnup profiles, control blade exposure, and others can be identified to allow a simple, bounding approach to BWR BUC. One aspect of this investigation involves examining the effect of control blade insertion during operation on discharged assembly reactivity. In the course of these calculations, an apparent source convergence problem was discovered for fuel that has experienced partial blade insertion for the entire lifetime of the assembly. The source convergence problem appears not to impact k{sub eff}, but it manifests in predictions of the axial fission density profile. This phenomenon is of interest in identifying areas of concern with BWR BUC since it has not been studied as thoroughly as BUC for pressurized-water (PWR) reactor fuel. There may also be interest in this configuration for further study of a realistic source Monte Carlo convergence problem as opposed to some earlier manufactured source convergence problems through careful selection of initial conditions. This summary presents the depletion conditions used to generate the problem, a description of the models, a background based on well-behaved calculations, the identification of the problem, and attempts made to resolve the problem. Only a brief description of the depletion conditions and models is possible within the limited scope of this summary. Finally, conclusions are presented. This summary identifies a source convergence problem in the process of investigating BUC for BWR spent fuel. The depletion scenario which created the depleted fuel and burnable absorber compositions included a control blade inserted in the bottom 14 nodes throughout the entire depletion. This insertion is slightly over half the length of the assembly, and it appears to create two regions of nearly equal reactivity. As expected, one region is near the top of the assembly, and the other region is near the middle of the assembly. This node includes significant {sup 239}Pu generation as a result of rodded operation, but it is also the top node of the full lattice zone. While the calculated k{sub eff} values appear to be statistically equivalent, the axial neutron production profile varies significantly among independent simulations of the same model. A range of standard approaches has been used to attempt to resolve the source convergence problem and determine the true axial neutron production profile. This profile is of interest in cask criticality safety analysis because it influences the interaction among assemblies loaded in the cask. The forthcoming SCALE 6.2 release will include source convergence testing based on Shannon entropy, which may assist in identifying these types of problems in the future. It should be noted that this source convergence problem results from the depletion conditions and the final distribution of fissile and absorber material within the discharged fuel assembly. The results, while entirely generated within the SCALE code system, are representative of any Monte Carlo program attempting to calculate k{sub eff} for such a system. The most important conclusion of this work is that the BUC criticality safety community must be aware of the potential for this type of source convergence problem. Analysts must approach such partially rodded scenarios with caution and critically examine the results. Fortunately, it is extremely unlikely that BWR assemblies would experience the bladed operation necessary to create this particular source convergence problem. These results may also have some bearing on the analysis of PWR BUC for new plant designs such as AP1000 that incorporate significant rodded operations. In a broader context, the source convergence problem identified here could have been magnified if it had occurred in a Monte Carlo depletion simulation. It may be possible to identify this type of problem in a depletion calculation by comparing the apparently converged fluxes between steps to ensure that no oscillations or other serious shifts are occurring. The depletion calculations performed in this work were performed with a two-dimensional deterministic code and are therefore not subject to this problem. These results may also raise questions about the validity of 2D depletion models with extruded geometry in the 3D k{sub eff} calculation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-Energy and Stable Subfreezing Aqueous Zn–MnO 2 Batteries with Selective and Pseudocapacitive Zn-Ion Insertion in MnO 2

One major challenge of aqueous Zn–MnO 2 batteries for practical applications is their unacceptable performance below freezing temperatures. Here, in this study, the use of simple Zn(ClO 4 ) 2 aqueous electrolytes is described for all-weather Zn–MnO 2 batteries even down to -60 °C. The symmetric, bulky ClO 4 - anion effectively disrupts hydrogen bonds between water molecules and provides intrinsic ion diffusion even while frozen, and enables ≈260 mAh g -1 on MnO 2 cathodes at -30 °C . It is identified that subfreezing cycling shifts the reaction mechanism on the MnO 2 cathode from unstable H+ insertion to predominantly pseudocapacitive Zn 2+ insertion, which converts MnO 2 nanofibers into complicated zincated MnO x that are largely disordered and appeared as crumpled paper sheets. The Zn 2+ insertion at -30 °C is faster and much more stable than at 20 °C, and delivers ≈80% capacity retention for 1000 cycles without Mn 2+ additives. In addition, simple Zn(ClO 4 ) 2 electrolyte also enables a nearly fully reversible and dendrite-free Zn anode at -30 °C with ≈98% Coulombic efficiency. Zn–MnO 2 prototypes with an experimentally verified unit energy density of 148 Wh kg -1 at a negative-to-positive ratio of 1.5 and an electrolyte-to-capacity ratio of 2.0 are further demonstrated.

25 ENERGY STORAGE↗

Cutting force and stability prediction for inserted cutters

Here, this paper presents an approach for inserted end/face mill force and stability predictions using a reverse engineering approach. Structured light scanning is implemented to identify the spatial coordinates of the points that define the multiple insert cutting edges. These points are analyzed to extract the cutting edge radius and angle values, which are then incorporated in a time domain simulation that predicts cutting force and tool/workpiece deflection for user-selected operating parameters. Good agreement between predicted and measured cutting forces is first demonstrated. The process stability is then predicted using the validated force model and measured structural dynamics. Observations about the stability dependence on insert geometry are finally presented for a selected end mill.

Machining↗

Development of a Bi2212 Dipole Insert at Fermilab

A goal of the U.S. Magnet Development Program (US-MDP) is high-field magnets for accelerators with magnetic fields larger than 15 T, i.e., above the limits of Nb 3 Sn accelerator magnets. Composite round wires and Rutherford cables made of high temperature superconductor Bi2212 may achieve this goal. Bi2212 is sensitive to transverse stresses and strains, and this requires stress management in the coil design. A stress management approach was developed at Fermilab for high-field large-aperture Nb 3 Sn accelerator magnets. Now it is being applied to high-field dipole insert coils based on Bi2212 Rutherford cable. Here this paper describes the insert coil design and main parameters, including the superconducting wire and cable. The coil will be installed inside a 60-mm bore Nb 3 Sn dipole outsert coil and cold iron yoke. The Bi2212 coil will be tested individually and in series with the Nb 3 Sn outsert coil. The expected Bi2212 insert test parameters are reported and discussed.

43 PARTICLE ACCELERATORS↗

The Insertion Green Monster (iGM) Method for Expression of Multiple Exogenous Genes in Yeast

Being a simple eukaryotic organism, Saccharomyces cerevisiae provides numerous advantages for expression and functional characterization of proteins from higher eukaryotes, including humans. However, studies of complex exogenous pathways using yeast as a host have been hampered by the lack of tools to engineer strains expressing a large number of genetic components. In addition to inserting multiple genes, it is often desirable to knock out or replace multiple endogenous genes that might interfere with the processes studied. Here, we describe the “insertion Green Monster” (iGM) set of expression vectors that enable precise insertion of many heterologous genes into the yeast genome in a rapid and reproducible manner and permit simultaneous replacement of selected yeast genes. As a proof of principle, we have used the iGM method to replace components of the yeast pathway for methionine sulfoxide reduction with genes encoding the human selenoprotein biosynthesis machinery and generated a single yeast strain carrying 11 exogenous components of the selenoprotein biosynthetic pathway in precisely engineered loci.

Saccharomyces cerevisiae↗

Interface Promoted Reversible Mg Insertion in Nanostructured Tin-Antimony Alloys

This paper demonstrates intermetallic compounds SnSb are highly active materials for reversibly hosting Mg ions. Compared with monometallic Sn and Sb, SnSb alloy exhibited exceptionally high reversible capacity (420 mAh/g), excellent rate capability and good cyclic stability. Mg insertion into pristine SnSb involves an activation process to complete, which induces particle breakdown and results in phase segregation to Sn-rich and Sb-rich phases. Both experimental analysis and DFT simulation suggest that the Sn-rich phase is particularly active and provides most of the capacity whereas the Sb-rich phase is not as active, and the interface between these two phases play a key role in promoting the formation and stabilization of the cubic Sn phase that is more favorable for fast and reversible Mg insertion. We further show that activated SnSb alloy has good compatibility with simple Mg electrolytes. Overall, this work could provide new approaches for designing materials capable of reversible Mg ion insertion and new opportunities for understanding Mg electrochemistry.

Environmental Molecular Sciences Laboratory↗

An Aqueous Dual‐Ion Battery Cathode of Mn 3 O 4 via Reversible Insertion of Nitrate

Abstract We report reversible electrochemical insertion of NO 3 − into manganese(II, III) oxide (Mn 3 O 4 ) as a cathode for aqueous dual‐ion batteries. Characterization by TGA, FTIR, EDX, XANES, EXAFS, and EQCM collectively provides unequivocal evidence that reversible oxidative NO 3 − insertion takes place inside Mn 3 O 4 . Ex situ HRTEM and corresponding EDX mapping results suggest that NO 3 − insertion de‐crystallizes the structure of Mn 3 O 4 . Kinetic studies reveal fast migration of NO 3 − in the Mn 3 O 4 structure. This finding may open a new direction for novel low‐cost aqueous dual‐ion batteries.

Jiang, Heng↗

Mechanistic Studies on the Insertion of Carbonyl Substrates into Cu‐H: Different Rate‐Limiting Steps as a Function of Electrophilicity

Abstract We report mechanistic studies on the insertion reactions of [(NHC)Cu(μ‐H)] 2 complexes with carbonyl substrates by UV‐vis and 1 H NMR spectroscopic kinetic studies, H/D isotopic labelling, and X‐ray crystallography. The results of these comprehensive studies show that the insertion of Cu‐H with an aldehyde, ketone, activated ester/amide, and unactivated amide consist of two different rate limiting steps: the formation of Cu‐H monomer from Cu‐H dimer for more electrophilic substrates, and hydride transfer from a transient Cu‐H monomer for less electrophilic substrates. We also report spectroscopic and crystallographic characterization of rare Cu‐hemiacetalate and Cu‐hemiaminalate moieties from the insertion of an ester or amide into the Cu−H bond.

Tran, Ba L.↗

An Aqueous Dual-Ion Battery Cathode of Mn 3 O 4 via Reversible Insertion of Nitrate

We report reversible electrochemical insertion of NO3- into manganese(II, III) oxide (Mn3O4) as a cathode for aqueous dual-ion batteries. Characterization by TGA, FTIR, EDX, XANES, EXAFS, and EQCM collectively provides unequivocal evidence that reversible oxidative NO 3 - insertion takes place inside Mn 3 O 4 . Ex situ HRTEM and corresponding EDX mapping results suggest that NO 3 - insertion de-crystallizes the structure of Mn 3 O 4 Kinetic studies reveal fast migration of NO 3 - in the Mn 3 O 4 structure. This finding may open a new direction for novel low-cost aqueous dual-ion batteries.

25 ENERGY STORAGE↗

Mechanistic Studies on the Insertion of Carbonyl Substrates into Cu-H: Different Rate-Limiting Steps as a Function of Electrophilicity

In this paper, we report mechanistic studies on the insertion reactions of [(NHC)Cu(H)] 2 complexes with carbonyl substrates by UV-vis and 1 H NMR spectroscopic kinetic studies, H/D isotopic labelling, and X-ray crystallography. The results of these comprehensive studies show that the insertion of Cu-H with an aldehyde, ketone, activated ester/amide, and unactivated amide consist of two different rate limiting steps: the formation of Cu-H monomer from Cu-H dimer for more electrophilic substrates and hydride transfer from a transient Cu-H monomer for less electrophilic substrates. We also report spectroscopic and crystallographic characterization of rare Cu-hemiacetalate and Cu-hemiaminalate moieties from the insertion of an ester and amide into the Cu-H bond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Placement of a peripherally inserted central catheter into the azygous vein

Peripherally inserted central catheters (PICC) are used for a variety of infusion therapies. They are indicated in patients requiring long-term venous access. Incorrect positioning of the insertion of a PICC line is one of the known complications when inserting the device in clinical practice. Radiographers once performing imaging will commonly check if the tip of a PICC has entered the superior vena cava. This case study will report on a lesser known incorrect placement of a PICC line into the azygous vein and how this can be detected on radiographic imaging. This outcome for the patient can be detrimental as it has an increased risk of perforation, thrombus, and fistula formation.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

A Deep-Learning System for Fully-Automated Peripherally Inserted Central Catheter (PICC) Tip Detection

A peripherally inserted central catheter (PICC) is a thin catheter that is inserted via arm veins and threaded near the heart, providing intravenous access. The final catheter tip position is always confirmed on a chest radiograph (CXR) immediately after insertion since malpositioned PICCs can cause potentially life-threatening complications. Although radiologists interpret PICC tip location with high accuracy, delays in interpretation can be significant. In this study, we proposed a fully-automated, deep-learning system with a cascading segmentation AI system containing two fully convolutional neural networks for detecting a PICC line and its tip location. A preprocessing module performed image quality and dimension normalization, and a post-processing module found the PICC tip accurately by pruning false positives. Our best model, trained on 400 training cases and selectively tuned on 50 validation cases, obtained absolute distances from ground truth with a mean of 3.10 mm, a standard deviation of 2.03 mm, and a root mean squares error (RMSE) of 3.71 mm on 150 held-out test cases. This system could help speed confirmation of PICC position and further be generalized to include other types of vascular access and therapeutic support devices.

62 RADIOLOGY AND NUCLEAR MEDICINE↗