Search NASA⌕ Search

SEARCH · Search NASA

Results for “maximum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Directional dependence of equilibrated TLD-400 chips in multiple radiation fields

Fielding of thermoluminescent dosimeters (TLDs) for measurement of photon radiation dose in experiments is the standard practice for γ-irradiation facilities, pulsed power x-ray facilities, and reactor facilities at Sandia National Laboratories (SNL). Due to the high-dose experimental conditions and the mixed ( 1 n, γ) fields in these facilities, SNL radiation metrologists have historically used CaF 2 :Mn TLDs (also known as TLD-400). Recent inquiries to the radiation metrology staff have raised concerns that the aluminum-equilibrated TLD-400 chips may exhibit a directionally dependent response. The metrologists were asked whether the dose measured by the chip may be impacted by the angle of incidence on the equilibrated TLD. To provide a thorough answer to this query, a set of adjoint Monte Carlo radiation transport calculations was performed for three different equilibrated TLDs as well as bare TLD chips using the Integrated Tiger Series (ITS) code. The key feature of the adjoint calculations performed in this study is that each photon escaping the modeled geometry was tallied into angular bins to provide information on both the energy and angular dependence of the equilibrated chip. After the adjoint Monte Carlo calculations were completed, the resulting energy-dependent response function for each angular bin was convolved with multiple photon energy spectra representing various radiation facilities at SNL. The radiation facilities selected for analysis span a range of photon energies from approximately 1 keV up to approximately 20 MeV. Thus, the presented results are applicable to a wide variety of radiation facilities around the world. Although the bare TLD-400 chip was expected to display the largest variation due to the photon angle of impact on the dosimeter, the dosimeter with the thinnest aluminum equilibrator (SNL thin equilibrated TLD-400) was determined to have the biggest differential between the impact angle with the maximum dose ( D max ) and the impact angle with the minimum dose ( D min ). However, the SNL normal equilibrated TLD-400 chip demonstrated a dramatic reduction in that differential between maximum and minimum dose angles. The reduction in this differential is one of the dominant factors in experimenters’ choice to field these dosimeters at SNL radiation facilities. The results from the PNNL (Hanford) energy-flattening field capsule are consistent with the previous publications. The differential dose responses due to the photon impact angle indicate that experimenters should strive to field their TLD-400 dosimeters in a consistent manner to avoid additional uncertainty in the measurements based on dosimeter orientation.

Adjoint radiation transport↗
DOE OSTI2025

Analysis of pumped thermal energy storage using particle media integrated with concentrating solar power

Pumped Thermal Energy Storage (PTES) is an electricity storage system that converts electricity into thermal energy which is stored and later transformed back into electricity. Previous work has illustrated that particles have low capital costs and can be operated over a wide range of temperatures. PTES with particle storage achieves higher round-trip efficiency and specific power output than when molten salt thermal energy storage is used. This article explores hybrid systems that combine PTES with Concentrating Solar Power (CSP). Hybrid systems share the majority of components thereby reducing costs compared to two stand-alone devices. In addition, hybrid systems can provide multiple services (such as renewable power generation and electricity storage services). Using particle thermal storage in these hybrid concepts provides freedom in choosing the design conditions, since a wide range of operating temperatures is allowable, therefore making it possible to identify hybrid system designs that have good performance. In this article, two concepts for hybrid PTES-CSP are introduced. Thermodynamic models are developed and these are used to evaluate the performance of two hybrid systems. These models account for turbomachinery efficiency, and approach temperature and pressure loss in heat exchangers, as well as other sources of inefficiency, such as motor-generator losses, and air fan power. The “Solar Top-Up” Concept uses CSP to increase the temperature delivered by the charging heat pump. The discharging system uses a topping gas cycle and a bottoming steam cycle to fully exploit the available energy. Using solar heat to increase the maximum temperature from 750 K to 1100 K increases the round-trip efficiency from 41 % to 62 % and the specific work output from 88 kJ/kg to 301 kJ/kg. The second concept is a “Dual-Mode” device which provides both electricity storage and solar electricity generation with the same set of components. The PTES-mode and CSP-mode performance are optimized at different design values but careful parameter selection leads to good performance of both modes: one design produces PTES round-trip efficiency > 60 %, CSP heat engine efficiency > 40 %, and specific work outputs > 150 kJ/kg (for both cycles), when the particle receiver temperature is > 1200 K and maximum heat pump temperature is 1100 K.

14 SOLAR ENERGY↗
DOE OSTI2025

Surface roughness and dimensional evaluation of laser powder bed fusion additively manufactured shell and tube heat exchangers

The growing interest in additively manufactured (AM) heat exchangers drove the need to understand how this construction technique impacts heat exchanger performance. Two primary factors driven by AM that influence heat exchanger performance are surface roughness and geometry. To better understand these parameters, a range of shell and tube heat exchangers constructed using laser powder bed fusion were evaluated. Of those evaluated, the surface roughness throughout a fourteen-tube, zero-baffle heat exchanger was measured using computed tomography. Between the inner and outer tubes, the inner tube surfaces had a greater surface roughness than the outer by 8.07 μm, while the surfaces at the top of the build volume had higher surface roughness values than the bottom. Dimensionally, the inner tube diameters of this heat exchanger were 0.15% different from the design value, while the outer diameters were within a 0.84 % difference. Manual measurements across seven other heat exchangers yielded a maximum 1.15% difference between the design and measured diameters. Across the build volume for all heat exchangers studied, the tube diameters at the top were larger than at the bottom by a maximum of 1.24% difference. Inconsistent melting throughout the individual parts and the build volume, as well as particle splatter and thermal gradient variation were attributed to the surface roughness and dimensional changes seen. These results strengthen the knowledge of dimensional and surface roughness considerations when designing AM heat exchangers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Autonomous online optimization of a closed-circuit reverse osmosis system

As freshwater becomes increasingly scarce, many industrial and municipal water utilities look at premise-scale water treatment and reuse to meet water demand. Closed-circuit reverse osmosis (CCRO) has been proposed as a promising process design to do so. This sequencing batch process enables operation at higher brine salinity levels by means of a recycle flow. Optimal operation requires that the maximum salinity level at the membrane surface represents an optimal trade-off between brine disposal costs and energy efficiency. This maximum salinity level may change over time as the feed water composition changes and electricity markets fluctuate. In this article, we present the results of the experimental evaluation of an automatic technique for continuous online optimization, known as extremum seeking control. This technique has a long history in the process control community but has received little traction so far in the water industry. We modify this technique to enable its use for online optimization of CCRO, specifically to account for its sequential batch operation. We challenge the optimization schemes through several experimental tests and illustrate the advantages and drawbacks of extremum-seeking control.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Inertial collapse of a gas bubble in a shear flow near a rigid wall

Despite the extensive research on bubble collapse near rigid walls, the bubble collapse dynamics in the presence of shear flow near a rigid wall is poorly understood. We conduct direct simulations of the Navier–Stokes equations to explore the bubble dynamics and pressures during bubble collapse near a rigid, flat wall under linear shear flow conditions. We examine the dependence of the bubble collapse morphology and wall pressures on the initial bubble location and shear rate. We find that shear distorts the bubble, generating two re-entrant jets – one developing from the side opposite to the mean flow and the other from the far end toward the wall. Upon impact of the jet on the opposite side of the bubble, water-hammer shocks are produced, which propagate outward and interact with the convoluted bubble shape. The shock stretches the bubble towards the wall, resulting in a closer impact location for the jet originating from the far end compared with the case with no shear flow. The water-hammer pressure location can be approximated as the theoretical distance travelled by a particle initialised at the bubble centre with the corresponding constant shear flow velocity. The maximum wall pressures can thus be predicted by considering the distance between the far jet impingement location and the wall along the wall-normal direction. As the shear rate is increased, the maximum wall pressure increases, although only marginally. We determine the critical initial stand-off distance from the wall at which the bubble morphology is shear dominated, i.e. characterised by converging re-entrant jets.

Bhola, Sahil (ORCID:0000000236766302)↗
DOE OSTI2024

Latest Pleistocene glacial chronology and paleoclimate reconstruction for the East River watershed, Colorado, USA

Reconstructing Pleistocene glaciation timing and extent is vital for understanding paleoclimate. Whereas late Pleistocene glaciation has been studied extensively in western North American mountain ranges, the glacial history of the western Elk Range in Colorado remains understudied, particularly in the East River watershed, a site of intense scientific focus. Here we use cosmogenic nuclide exposure and depth–profile dating methods to determine the timing of glaciation in the East River watershed. We use glacier modeling to reconstruct paleoglacier extents and quantify past climate conditions. Our findings indicate that the East River glacier retreated from its maximum position approximately 17–18 ka, moving to recessional positions between 13 and 15 ka, before experiencing more substantial retreat to high-elevation cirques around 13 ka. Glacier modeling suggests that the maximum ice extents at 17–18 ka could have been sustained by temperature depressions of approximately −6.5°C compared to modern conditions, assuming consistent precipitation. Additionally, the ice position at 13–15 ka could have been supported by temperature depressions of around −4.0°C. These results offer insights into the deglaciation timeline in the East River watershed and broader western Elk Range as well as paleoclimate conditions during the late Pleistocene, which may aid future research on critical zone evolution in the East River watershed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

The effect of shear flow on the resistive tearing instability

We develop a new scaling theory for the resistive tearing mode instability of a current sheet with a strong shear flow across the layer. The growth rate decreases with increasing flow shear and is completely stabilized as the shear flow becomes Alfvénic: both in the constant-Ψ regime, as in previous results, but we also show that the growth rate is in fact suppressed more strongly in the nonconstant-Ψ regime. As a consequence, for sufficiently large flow shear, the maximum of the growth rate is always affected by the shear suppression, and the wavenumber at which this maximum growth rate is attained is an increasing function of the strength of the flow shear. These results may be important for the onset of reconnection in imbalanced MHD turbulence.

astrophysical plasmas↗
DOE OSTI2026

Low-Lying Excited States of Linear All- Trans Polyenes: Insights from Analytic Gradient and Nonadiabatic Coupling Calculations Based on Multireference Configuration Interaction

Polyenes serve as a rigorous test for theoretical models and electronic structure methods, playing a key role in advancing computational and theoretical chemistry. Here, we present a high-level theoretical investigation of linear, all-trans polyenes using energy gradients and nonadiabatic coupling vectors based on an MR-CISD wave function to describe electronic transitions involving the ground state (1 1 A g – ) and three low-lying excited states (2 1 A g – , 1 1 B u + , and 2 1 B u – ) of hexatriene, octatetraene, and decapentaene. This approach enables accurate evaluation of both adiabatic and vertical excitation and emission energies, yielding results in excellent agreement with experiment, as well as locating minima on the crossing seam between adiabatic states. Our results show that vertical excitation energies to the 1 1 B u + state are blue-shifted by 0.2–0.3 eV relative to the experimental absorption maximum, whereas the vertical emission energy from the 2 1 A g – state is red-shifted by ∼0.2 eV relative to the experimental emission maximum. Upon relaxation from the Franck–Condon geometry, the 2 1 A g – state stabilizes by around 1 eV, compared to 0.2–0.3 eV for the 1 1 B u + state. An analysis of the S 1 /S 0 crossing seam in hexatriene shows that its minimum involves asymmetric backbone deformations and provides an efficient channel for ultrafast internal conversion to the ground state, consistent with the absence of detectable fluorescence in this molecule. These results demonstrate the power of analytic gradients and nonadiabatic coupling vectors based on an MR-CISD wave function for accurately characterizing the electronic structure and photophysics of polyenes.

Excited states↗
DOE OSTI2024

Reductive Dynamic and Static Excited State Quenching of a Homoleptic Ruthenium Complex Bearing Aldehyde Groups

A new homoleptic Ru polypyridyl complex bearing two aldehyde groups on each bipyridine ligand, [Ru(dab) 3 ](PF 6 ) 2 , where dab is 4,4′-dicarbaldehyde-2,2′-bipyridine, was synthesized, characterized, and utilized for iodide photo-oxidation studies. In acetonitrile (CH 3 CN) solution, the complex displayed an intense metal-to-ligand charge transfer (MLCT) absorbance maximum at 475 nm (ε = 22,000 M –1 cm –1 ) and an infrared (IR) band at 1712 cm –1 assigned to the pendent aldehyde groups. Visible light excitation in air-saturated solution resulted in room temperature photoluminescence (PL) with a maximum at 675 nm, a quantum yield, ϕ PL = 0.048, and an excited state lifetime, τ ο = 440 ns, from which radiative and nonradiative relaxation rate constants were extracted, k r = 9.1 × 10 4 s –1 and knr = 1.8 × 10 6 s –1 . Pulsed visible light excitation yielded transient UV–vis and IR absorption spectra consistent with an MLCT excited state; relaxation occurred with the maintenance of two isosbestic points in the visible region, and a lifetime that agreed with that measured by time-resolved PL. Cyclic voltammetry studies in a CH 3 CN solution with 0.1 M TBAPF 6 electrolyte revealed a quasi-reversible oxidation, E°(Ru III/II ) = +1.25 V vs. Fc +/0 , and three sequential one-electron reductions at −1.10, −1.25, and −1.54 V vs. Fc +/0 . Here, an excited state reduction potential of E°(Ru *2+/+ ) = +0.89 V vs. Fc +/0 was estimated with the Rehm–Weller expression. Titration of tetrabutylammonium iodide, TBAI, into a CD 3 CN solution of [Ru(dab) 3 ](PF 6 ) 2 resulted in significant shifts in the aldehyde H atom and 3,3′-biypridyl resonances that were analyzed with a 1:1 equilibrium model, from which K eq = 460 M –1 was extracted, increasing to 5800 M –1 when the solvent was changed to acetone-d 6 . Iodide titrations resulted in a significant quenching of the [Ru(dab) 3 ] *2+ lifetime and quantum yield in both CH 3 CN and acetone solvents. In CH 3 CN, the quenching was mainly dynamic and well described by the Stern–Volmer model, from which a quenching rate constant, k q , of 4.5 × 10 10 M –1 s –1 and an equilibrium constant, K eq , of 8.3 × 10 3 M –1 were obtained. In acetone, the static quenching pathway by iodide was greatly enhanced, with a K eq of 1.2 × 10 4 M –1 and a higher k q of 9.2 × 10 10 M –1 s –1 .

Aldehydes↗
DOE OSTI2026

Unraveling In-Situ Formation of Surface Nickel Nitride Structures in Plasma-Assisted Catalytic Ammonia Synthesis

We report the in situ formation of Ni nitride for plasma-assisted ammonia synthesis. Both the surface nitrogen concentration and the ammonia formation rate exhibit dependence on the N 2 :H 2 feed ratio. The maximum surface nitrogen concentration occurs at a N 2 :H 2 ratio of 4:1, and the maximum catalytic activity occurs at 2:1. In contrast, the formation of gas phase radicals is less sensitive to feed composition, indicating that Ni nitride is more kinetically relevant to ammonia production than gas-phase radicals. The plasma-induced formation of Ni nitride is therefore proposed to be a critical contributor to the synergistic effects in plasma-assisted catalytic ammonia synthesis. Additionally, Ni nitride alters the surface reaction mechanism of plasma-assisted ammonia synthesis, with the rate-determining-step (RDS) shifting to surface-bound NH 3 formation rather than N 2 activation at temperatures below 373 K. These findings provide mechanistic insight that opens opportunities for optimizing the performance of plasma-assisted catalytic ammonia synthesis

Ammonia↗
DOE OSTI2025

Boosting Tin Perovskite Solar Cell Performance via Light-Induced Interface Doping

Continuous breakthroughs have been achieved in the photoelectric conversion efficiency (PCE) of tin-based perovskite solar cells (TPSCs) in recent years. Inspired by performance improvements observed during device storage, we identified beneficial light-induced interface doping (LIID) in the TPSCs. In situ analyses using X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy reveal that ion migration and oxidation at the interface induce beneficial doping effects, enhancing carrier transport and significantly boosting device performance. By implementing specific illumination techniques or maximum power point tracking (MPPT) methods to achieve LIID, we increased the open-circuit voltage while maintaining a high short-circuit current, reaching a PCE of up to 14.91%. Furthermore, this efficiency was sustained at 70% of its maximum value after nearly 900 h of continuous operation. Our study introduces a novel approach to addressing energy band mismatch, paving the way for improved efficiency in tin-based perovskite solar cells.

Sun, Mulin↗
DOE OSTI2025

Unveiling the Role of In Situ Al 2 O 3 Passivation in Molecular-Ink-Processed CuIn(S,Se) 2 Photovoltaics

Here, we report on the optimization of in situ passivation of ink-based CuIn(S,Se) 2 thin-film solar cells via controlled incorporation of Al 2 O 3 in CuIn(S,Se) 2 films by the addition of Al(NO 3 ) 3 to the molecular ink precursor. For this purpose, the Al/(Al + In) (AAI) metal ratio was varied from 0.05 to 0.30. We observe that the efficiency of the cells made of Al 2 O 3 -incorporated CuIn(S,Se) 2 is consistently higher than those without Al 2 O 3 , especially due to an improvement in open-circuit voltage (V OC ) and fill factor (FF), for all tested AAI ratios. With an AAI of 0.05, a maximum efficiency of 11.2% and an average efficiency of 8.5% (measured across 18 cells) was achieved, compared to 8.5% maximum efficiency and 6.5% average efficiency for Al-free CuIn(S,Se) 2 . Furthermore, we find that cells made of Al 2 O 3 -incorporated CuIn(S,Se) 2 with an AAI of 0.2 show a narrow distribution in the photovoltaic performance, indicating higher reproducibility and higher FF. Energy-dispersive X-ray spectroscopy shows that, at AAI = 0.2, Al 2 O 3 is distributed more homogeneously at the surface of the Al 2 O 3 -incorporated CISSe. Capacitance-voltage measurements reveal a reduced defect density by incorporation of Al 2 O 3 , which could be partly responsible for the higher V OC . Furthermore, using detailed surface analysis with various X-ray and electron spectroscopy methods, we derive chemical and electronic structure information from the surface. With ultraviolet photoelectron (UPS) and inverse photoemission spectroscopies (IPES), the electronic band gap of the CuIn(S,Se) 2 thin-film surface is found to increase from 1.22 to 1.88 eV (+-0.12 eV) with Al 2 O 3 incorporation. This is accompanied by a clear reduction of the conduction band spike at the CdS/CISSe interface due to Al 2 O 3 addition, as derived by both UPS and IPES as well as temperature-dependent V OC measurements.

14 SOLAR ENERGY↗
DOE OSTI2026

Intrinsically Conductive {pi}‑d Conjugated Layers with Co–N4 Active Sites for Efficient Nitrate Electrocatalysis and Zinc-Nitrate Batteries

Electrochemical synthesis of ammonia from nitrate has been extensively investigated as a potential alternative to the energy-intensive Haber-Bosch process. This approach not only operates under ambient conditions but also simultaneously removes nitrate contaminants while producing ammonia as a value-added product. However, the ongoing quest lies in designing an efficient electrocatalyst that achieves a high ammonia yield rate, high selectivity, and long-term stability. Herein, we report the outstanding performance of a Co–N4 coordinated π-d layered Co3(HITP)2 (HITP = 2,3,6,7,10,11-hexaiminotriphenylene) in nitrate electrocatalysis. The unique combination of abundant Co–N4 active sites and superior electrical conductivity enables significant electrocatalytic activity, delivering a maximum ammonia yield rate of 56.8 mg cm–2 h–1 at −0.8 V vs RHE and a Faradaic efficiency of ∼91% at −0.4 V vs RHE. Mechanistic analysis reveals that alkaline conditions accelerate water dissociation to generate adsorbed hydrogen intermediates (H*), which are utilized by Co–N4 sites to drive the stepwise hydrogenation of nitrate to ammonia while suppressing competing hydrogen evolution reaction (HER) pathways. Furthermore, integration of this catalyst into a zinc-nitrate battery resulted in a maximum power density of 5.3 mW cm–2 and an open-circuit potential of ∼1.45 V. These results highlight the potential of π-d conjugated Co–N4 materials as an efficient catalyst for both environmental remediation and energy conversion.

Namvar, shahrirar↗
DOE OSTI2024

Catalytic Resonance Theory: Turnover Efficiency and the Resonance Frequency

Programmable catalysts exhibiting forced oscillation in the free energy of reacting surface species were simulated to understand the general mechanisms leading to efficient use of the input energy. Catalytic ratchets with either positive or negative adsorbate scaling exhibited oscillation conditions of both high and low turnover efficiency, yielding catalytic turnover frequencies either close to or significantly lower than the applied catalyst oscillation frequency, respectively. The “effective rate”, defined as the product of the catalytic turnover frequency and the turnover efficiency (ηTOE), was limited via two catalytic mechanisms: a leaky catalytic ratchet existed when molecules repeatedly traversed backward through the catalytic transition state upon catalyst oscillation, while a catalytic ratchet with low surface participation exhibited reduced formation of a gas-phase final product due to low surface product coverage. Furthermore, a single applied frequency yielding a maximum effective catalytic rate defined as the “resonance frequency” provided maximum combined benefit for catalytic rate and efficiency.

25 ENERGY STORAGE↗
DOE OSTI2025

Elastomer Mechanics of Cross-Linked Linear-Ring Polymer Blends

Cross-linking a blend of linear and ring polymers creates a new topology-based dual-network elastomer in which the two components differ significantly in their topology. We use molecular simulations and topological analysis to examine key mechanical properties as functions of ring polymer volume fraction Φ R . For Φ R < Φ R *, where the rings begin to overlap, the network shear modulus G and the maximum stretch ratio λ p are weakly dependent on Φ R . For Φ R > Φ R *, entanglements trapped in the network are diluted as the rings overlap, leading to a significant decrease in G and an increase in λ p with increasing Φ R . Here, the peak tensile stress, σ p , exhibits a maximum around Φ R *, indicating an enhancement of network strength due to the stronger cohesion from the entanglements between linear and ring polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Impacts of Topography-Based Subgrid Scheme and Downscaling of Atmospheric Forcing on Modeling Land Surface Processes in the Conterminous US

The effects of small-scale topography-induced land surface heterogeneity are not well represented in current Earth System Models (ESMs). In this study, a new topography-based subgrid structure referred to as topographic units (TGU) designed to better capture subgrid topographic effects, and methods to downscale atmospheric forcing to the land TGUs have been implemented in the Energy Exascale Earth System Model (E3SM) Land Model (ELM). Effects of the subgrid scheme and downscaling methods on ELM simulated land surface processes are evaluated over the conterminous United States (CONUS). For this purpose, ELM simulations are performed using two configurations without (NoD ELM) and with (D ELM) downscaling, both using TGUs derived for the 0.5-degree grids and the same land surface parameters. Simulations using the two ELM configurations are compared over the CONUS domain, regional levels, and at observational sites (e.g., SNOTEL). The CONUS-level results suggest that D ELM simulates more snowfall and snow water equivalent (SWE), higher runoff, and less ET during spring and summer. Regional-level results suggest more pronounced impacts of downscaling over regions dominated by higher elevation TGUs and regions with maximum precipitation occurring during cool seasons. Results at the SNOTEL sites suggest that D ELM has superior capability of reproducing the observed SWE at 83% of the sites, with more pronounced performance over topographically heterogeneous TGUs with their maximum precipitation occurring during cool seasons. The results highlight the importance of improving representation of small-scale surface heterogeneity in ESMs and motivate future research to understand their effects on land-atmosphere interactions, streamflow, and water resources management over mountainous regions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Using Temporal Deep Learning Models to Estimate Daily Snow Water Equivalent Over the Rocky Mountains

Abstract In this study we construct and compare three different deep learning (DL) models for estimating daily snow water equivalent (SWE) from high‐resolution gridded meteorological fields over the Rocky Mountain region. To train the DL models, Snow Telemetry (SNOTEL) station‐based SWE observations are used as the prediction target. All DL models produce higher median Nash‐Sutcliffe Efficiency (NSE) values than a conceptual SWE model and interpolated gridded data sets, although mean squared errors also tend to be higher. Sensitivity of the SWE prediction to the model's input variables is analyzed using an explainable artificial intelligence (XAI) method, yielding insight into the physical relationships learned by the models. This method reveals the dominant role precipitation and temperature play in snowpack dynamics. In applying our models to estimate SWE throughout the Rocky Mountains, an extrapolation problem arises since the statistical properties of SWE (e.g., annual maximum) and geographical properties of individual grid points (e.g., elevation) differ from the training data. This problem is solved by normalizing the SWE with its historical maximum value to alleviate extrapolation for all tested DL models. Our work shows that the DL models are promising tools for estimating SWE, and sufficiently capture relevant physical relationships to make them useful for spatial and temporal extrapolation of SWE values.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

The Vertical Structure of Turbulence Kinetic Energy Near the Arctic Sea‐Ice Surface

Atmospheric turbulence over the Arctic sea-ice surface has been understudied due to the lack of observational data. In this study, we focus on the turbulence kinetic energy (TKE) over sea ice and distinguish its two different vertical structures, the “Surface” type and the “Elevated” type, using observations during the Multidisciplinary drifting Observatory for the Study of Arctic Climate expedition (MOSAiC). The “Surface” type has the maximum TKE near the surface (at 2 m), while the “Elevated” type has the maximum TKE at a higher level (6 m). The TKE budget analysis indicates that the “Elevated” type is caused by the increased shear production of TKE at 6 m. In addition, spectral analysis reveals that the contribution to TKE by horizontal large eddies is enhanced in the “Elevated” type. Finally, how the vertical structure of TKE affects the parameterization of turbulent momentum flux is discussed.

54 ENVIRONMENTAL SCIENCES↗