SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Generation of intense sonic and ultrasonic power in the weld zone, close to the puddle, reduces the porosity and refinement of the grain. The ac induction brazing power supply is modified with long cables for deliberate addition of resistance to that circuit. The concept is extensible to the molding of metals and plastics.
High pressure seals for rotating shafts are machined from a polyimide resin. It is more durable and cheaper than the older seals of plastic coated metal and works at temperatures between - 400 degrees and plus 900 degrees f.
Color and appearance properties of paint films and relations to amounts and properties of colorants, noting translucent plastics and metallized paint films
Electrode sealing and insulation for fuel cells containing caustic liquid electrolytes using powdered plastic and metal
Liquid and gaseous oxygen difluoride compatibility tests with plastic and metal orifices and metal ignition temperature data
The micrometeorite activity in a near-earth environment and the effect of the environment on microorganisms were studied by exposure of polished metal and plastic surfaces to the environment outside the Gemini spacecraft. Preliminary results are summarized as follows: (1) The cumulative influx rate in the size ranges from 10 to the minus 15th power to 10 to the minus 14th power gram was approximately 2 particles/ sq m/sec, as determined on the Gemini 12 mission; (2) The cumulative influx rate in the same mass range, as determined by the data from the Gemini 9 mission was almost 200 particles/ sq m/sec; and (3) The large particle cumulative influx rate was about 3 x 0.00001 particle/ sq m/sec, with a mass of the order of 10 to the minus 7th power gram. No living organisms could be found on the sterile collecting surfaces after recovery and handling.
Consideration of the problem of reducing the probability of mechanical failure of bladder systems used for the expulsion of propellants into liquid rocket engines. It is shown that individual local folds in collapsing bladders can be classified into single and double folds, specifiable by nondimensional geometrical parameters which directly define the maximum strains at these folds. From these maximum strains the number of collapse/inflation cycles to failure can be obtained from low-cycle fatigue data experimentally determined for the bladder material of interest. Cycle life data are presented in terms of true maximum strain for four metals, two plastics, and two elastomers. It is found that double folds give rise to much more severe folding strains than do simple folds.
Volatile organic liquid surface penetrants used with appropriate detector paper leave tested surfaces uncontaminated. Method can be used to detect minute cracks in materials such as metal, glass, plastics, ceramics, etc.
The lunar surface cosmic ray experiment, consisting of sets of mica, glass, plastic, and metal foil detectors, was successfully deployed on the Apollo 17 mission. One set of detectors was exposed directly to sunlight and another set was placed in shade. Preliminary scanning of the mica detectors shows the expected registration of heavy solar wind ions in the sample exposed directly to the sun. The initial results indicate a depletion of very-heavy solar wind ions. The effect is probably not real but is caused by scanning inefficiencies. Despite the lack of any pronounced solar activity, energetic heavy particles with energies extending to 1 MeV/nucleon were observed. Equal track densities of approximately 6000 tracks/cm sq 0.5 microns in length were measured in mica samples exposed in both sunlight and shade.
A laminate is obtained by providing a lightweight core material, such as a honeycombed plastic or metal, within the cavity defined by an annular mold cavity frame. Face sheets, which are to be bonded to the core material, are provided on opposite sides of the frame and extend over the frame, thus sealing the core material in the cavity. An adhesive is provided between the core material and the face sheets and the combined thickness of the core material and adhesive is a close fit within the opposed face sheets. A gas tight seal, such as an O-ring gasket, is provided between the frame and the face sheet members to form a gas tight cavity between the face sheet members and the frame. External heat and pressure are used to bond the face sheets to the core material. Gas pressure is introduced into the sealed cavity to minimize out-gasing of the adhesive.
Column has end caps held in place by springs; prefilled packs of absorbent can be exchanged quickly. Both ends of metal or plastic body tube of size which can hold adequate amount of absorbent are machined to provide seat for perforated plate and groove for its spring retainer ring.
Carbonate pretreatment produces highly bondable surface without harming film. Treatment is useful in developing low-cost mirrors and solar concentrators fabricated from metal-coated plastic films. Treatment should cost no more than standard degreasing and rinsing procedures.
An experimental program has been undertaken to investigate and develop methods for high-efficiency collection of dust particles during a rendezvous mission with a preselected comet. A laboratory apparatus has been designed and tested for acceleration of fine particles (0.1 to 100 microns) to velocities of 0.5 to 50 m/s. Tests of collection efficiency are being conducted under vacuum and with control of substrate temperature. Collection materials include filters, plastic films, metal foils, liquid metals, and sticky organic compounds. Results to date indicate that only certain materials will be adequate to meet collection requirements.
A nozzle for use with abrasive and/or corrosive materials is formed of sintered ceramic compositions having high temperature oxidation resistance, high hardness and high abrasion and corrosion resistance. The ceramic may be a binary solid solution of a ceramic oxide and silicon nitride, and preferably a ternary solid solution of a ceramic oxide, silicon nitride and aluminum nitride. The ceramic oxide is selected from a group consisting of Al2O3, Y2O3 and Cr2O3, or mixtures of those compounds. Titanium carbide particles are dispersed in the ceramic mixture before sintering. The nozzles are encased for protection from external forces while in use by a metal or plastic casing.
Since photons have momentum, a useful force can be obtained by reflecting sunlight off of a large, low mass surface (most likely a very thin metal-coated plastic film) and robbing the light of some of its momentum. A solar sail Engineering Development Mission (EDM) is currently being planned by the World Space Foundation for the purpose of demonstrating and evaluating solar sailing technology and to gain experience in the design and operation of a spacecraft propelled by sunlight. The present plan is for the EDM spacecraft to be launched (sail stowed) in a spin-stabilized configuration into an initial elliptical orbit with an apogee of 36,000 km and a perigee of a few hundred kilometers. The spacecraft will then use its own chemical propulsion system to raise the perigee to at least 1,200 km. The deployed sail will have an area of 880 sq m and generate a solar force of about 0.007 N.
Molten bubbles of metal or plastic coalesce into strong, lightweight materials that look like solidified foam. Bubbles formed in compartment that receives molten material and compressed gas that fills bubbles. Compartment has matrix of nozzles. Leaving nozzles, bubbles fall into acoustic chamber and coalesce; then drop through funnel and are cast into desired shape by extrusion or molding. Materials used for construction, extruded into molds, sawed, nailed, and generally handled as wood.
Two-part tool reconfigured for variety of jobs. Tool performs several functions useful in layout. Lines, curves, and angles made visible as either bright scribe marks or as dark pencil (or ink) marks. Multipurpose tool speeds up laying out of patterns on sheet metal, wood, plastic, or paper. Tool is carried in pocket, then quickly assembled for service as height gauge, pair of dividers, protractor, surface gauge, or square.
Spheres sized and treated for desired sieve properties. Filter constructed from densely packed spheres restrained by screens. Hollow gas-filled plastic or metal spheres normally used. Manufactured within one percent or better diameter tolerance. Normally, all spheres in filter of same nominal diameter. Filter used as sieve to pass only particles smaller than given size or to retain particles larger than that size. Options available under filter concept make it easy to design for specific applications.