SEARCH · Search NASA

Results for “microstructure prediction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Measurement of the time-temperature dependent dynamic mechanical properties of boron/aluminum composites

A relatively simple flexural vibration test is developed for accurate measurement of the low-strain dynamic modulus and damping capacity of B/Al composite bar specimens from -200 C to over 500 C. The specimens are prepared from 8-ply unidirectional panels containing 50 volume percent fibers composed of 203-micron commercial boron-on-tungsten fibers. The basic test technique consists of the forced flexural vibration of the composite bar specimens at their two lowest free-free symmetrical resonant modes in a high-vacuum cryostat furnace. Specimen damping is determined from oscilloscope photographs of the free decay obtained after simultaneously removing the resonant drive signal and grounding the vibration-drive electrode. The availability of time-temperature dynamic data coupled with the predictive accuracy of composite theory suggests a future potential for using such data in examining environmental effects on composite macrostructure and microstructure.

Dicarlo, J. A.↗

NASA NTRS1990

Corrosion fatigue crack propagation in metals

This review assesses fracture mechanics data and mechanistic models for corrosion fatigue crack propagation in structural alloys exposed to ambient temperature gases and electrolytes. Extensive stress intensity-crack growth rate data exist for ferrous, aluminum and nickel based alloys in a variety of environments. Interactive variables (viz., stress intensity range, mean stress, alloy composition and microstructure, loading frequency, temperature, gas pressure and electrode potential) strongly affect crack growth kinetics and complicate fatigue control. Mechanistic models to predict crack growth rates were formulated by coupling crack tip mechanics with occluded crack chemistry, and from both the hydrogen embrittlement and anodic dissolution/film rupture perspectives. Research is required to better define: (1) environmental effects near threshold and on crack closure; (2) damage tolerant life prediction codes and the validity of similitude; (3) the behavior of microcrack; (4) probes and improved models of crack tip damage; and (5) the cracking performance of advanced alloys and composites.

Gangloff, Richard P.↗

NASA NTRS2003

Ultra-Sensitive Magnetoresistive Displacement Sensing Device

An ultrasensitive displacement sensing device for use in accelerometers, pressure gauges, temperature transducers, and the like, comprises a sputter deposited, multilayer, magnetoresistive field sensor with a variable electrical resistance based on an imposed magnetic field. The device detects displacement by sensing changes in the local magnetic field about the magnetoresistive field sensor caused by the displacement of a hard magnetic film on a movable microstructure. The microstructure, which may be a cantilever, membrane, bridge, or other microelement, moves under the influence of an acceleration a known displacement predicted by the configuration and materials selected, and the resulting change in the electrical resistance of the MR sensor can be used to calculate the displacement. Using a micromachining approach, very thin silicon and silicon nitride membranes are fabricated in one preferred embodiment by means of anisotropic etching of silicon wafers. Other approaches include reactive ion etching of silicon on insulator (SOI), or Low Pressure Chemical Vapor Deposition of silicon nitride films over silicon substrates. The device is found to be improved with the use of giant magnetoresistive elements to detect changes in the local magnetic field.

Olivas, John D.↗

NASA NTRS2018

Aerospace Ceramic Materials: Thermal, Environmental Barrier Coatings and SiC/SiC Ceramic Matrix Composites for Turbine Engine Applications

Ceramic materials play increasingly important roles in aerospace applications because ceramics have unique properties, including high temperature capability, high stiffness and strengths, excellent oxidation and corrosion resistance. Ceramic materials also generally have lower densities as compared to metallic materials, making them excellent candidates for light-weight hot-section components of aircraft turbine engines, rocket exhaust nozzles, and thermal protection systems for space vehicles when they are being used for high-temperature and ultra-high temperature ceramics applications. Ceramic matrix composites (CMCs), including non-oxide and oxide CMCs, are also recently being incorporated in gas turbine engines for high pressure and high temperature section components and exhaust nozzles. However, the complexity and variability of aerospace ceramic processing methods, compositions and microstructures, the relatively low fracture toughness of the ceramic materials, still remain the challenging factors for ceramic component design, validation, life prediction, and thus broader applications. This ceramic material section paper presents an overview of aerospace ceramic materials and their characteristics. A particular emphasis has been placed on high technology level (TRL) enabling ceramic systems, that is, turbine engine thermal and environmental barrier coating systems and non-oxide type SiC/SiC CMCs. The current status and future trend of thermal and environmental barrier coatings and SiC/SiC CMC development and applications are described.

Thermal Barrier Coatings↗

NASA NTRSDate not supplied

Investigation of the effect of etch pits on the material properties of carbon fiber structures

It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material [1, 2]. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA [3] that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. Figure 1 shows a FiberForm sample with artificially generated pits of varying radii and pit density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography [4]. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.

PuMA↗

NASA NTRS1999

Microstructural Development of Directionally Solidified Hg(1-x)Zn(x)Se Alloys

Hg(1-x)Zn(x)Se alloys have been studied as an alternative to Hg(1-x)Cd(x)Te for the detection of electromagnetic radiation, because the shorter ZnSe and HgSe bonds have been predicted to improve lattice stability. Several ingots with x = 0.1 were directionally solidified using a modified Bridgman-Stockbarger method; one was grown in an applied magnetic field, which greatly reduced radial compositional variations. A method was developed to reduce wetting. This, combined with the convex liquid-solid interface shape, produced boules that were single crystalline after growing about 3.5 cm. Observed surface features indicated ampoule wetting was eliminated using a graphite getter. Microstructural characteristics were greatly improved over HgCdTe alloys. In six boules, a total of only one twin was observed. A method for polishing and producing dislocation etch pits was developed for these alloys, revealing dislocation etch pit densities one to two orders of magnitude less than HgTe-based alloys. A kink in the thermal profile during processing of one boule generated more dislocations than did lattice mismatch due to compositional variations. This alloy has improved microstructural properties and resistance to dislocation formation compared with similar II-VI alloys.

Cobb, S. D.↗

NASA NTRS2004

On Efficient Multigrid Methods for Materials Processing Flows with Small Particles

Multiscale modeling of materials requires simulations of multiple levels of structural hierarchy. The computational efficiency of numerical methods becomes a critical factor for simulating large physical systems with highly desperate length scales. Multigrid methods are known for their superior efficiency in representing/resolving different levels of physical details. The efficiency is achieved by employing interactively different discretizations on different scales (grids). To assist optimization of manufacturing conditions for materials processing with numerous particles (e.g., dispersion of particles, controlling flow viscosity and clusters), a new multigrid algorithm has been developed for a case of multiscale modeling of flows with small particles that have various length scales. The optimal efficiency of the algorithm is crucial for accurate predictions of the effect of processing conditions (e.g., pressure and velocity gradients) on the local flow fields that control the formation of various microstructures or clusters.

Thomas, James↗

NASA NTRSDate not supplied

AI-Enhanced Computational Tools for Entry Systems Modeling

To advance the understanding of complex atmospheric entry phenomena, NASA’s Entry Systems Modeling (ESM) team [1] has developed high-fidelity computational tools addressing multiscale challenges, from material microstructures to full-scale heatshield response. This abstract highlights a subset of ESM tools, focusing on AI integration to enhance workflows and predictive modeling. - PuMA [2] computes effective material properties from high-resolution micro-CT scans, supporting TPS analysis for NASA missions. - TomoSAM [3] automates 3D tomography dataset segmentation for PuMA using the Segment Anything Model, reducing manual effort and improving accuracy. - PATO [4] models porous reactive materials under extreme conditions, with advancements such as unified solvers, mechanical erosion, and TPS coatings for NASA missions. - arcjetCV [5] employs deep learning to analyze arc jet test footage, measuring recession rates, shape changes, and shock standoff distances, bridging simulations, and experiments to reveal TPS ablation behavior. - ARCHeS [6] simulates arc heater plasma flows, modeling turbulence, radiation, and electromagnetic interactions to optimize arc heater performance, validate TPS under extreme conditions, and serve as a foundation for developing digital twins of arc heater facilities. - SPARTA [7] simulates rarefied hypersonic flows and gas-surface interactions for planetary entry missions, leveraging GPU architectures for scalable and efficient aerothermal and ablation analyses. AI-driven solutions, such as deep learning segmentation, have streamlined workflows in ESM tools and still hold significant potential to further accelerate processes and enhance automation in entry systems modeling. [1] Haskins, J.B. (2023), [2] Ferguson, J.C. (2018), [3] Meurisse, J.B.E. (2018), [4] Semeraro, F. (2023), [5] Quintart, A. (2024) [6] Meurisse, J.B.E. (2022), [7] Plimpton, S.J. (2019)

Predictive Modeling↗

NASA NTRSDate not supplied

Microscale Constitutive Model Sensitivity on Multiscale Modeling of Fiber Reinforced Composites

Fiber reinforced composites are desirable in applications where low weight and high strength are needed, but are susceptible to microscale variability during manufacturing, making failure predictions difficult. The impact microscale variability has on macroscale mechanical response is difficult to predict due to the computational efficiency needed to simulate many, large, high fidelity, microscale models. In this study, a multiscale approach was taken to model 3-point bend, 4-point bend, and tensile experiments of a unidirectional composite from only having microstructure scans of these samples and constituent properties from literature. These scans were sampled with different sized windows, and statistically equivalent microstructures were generated, then simulated for stiffness, strength, and fracture toughness using an efficient micromechanical. Mesoscale models were created where element sizes equaled microstructure size, and properties were assigned through sampling of microscale simulation results. First, this study showed the effect of using Weibull scaling on constituent matrix strength on macroscale response. Then, a comparison was made between different element sizes and experiments. Finally, model dimensions were fixed, and the effect of randomly distributed local properties alone was examined. Results showed that the scatter of strength and stiffness in the experiments could be predicted well using images of the microscale fiber morphologies and that using stochastic properties produced a 3% coefficient of variation of strength for all experiments.

statistical microstructure↗

NASA NTRSDate not supplied

Investigation of the Effect of Etch Pits on the Material Properties of Carbon Fiber Structures

It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.

PuMA↗

NASA NTRS1995

Superconducting materials processing

The effects of materials processing on the properties and behavior of high temperature yttrium barium copper oxide (YBCO) superconductors were investigated. Electrical, magnetic, and structural characteristics of thin films (300 nm) YBA2CU3O(delta) structures grown by pulsed laser deposition on LaAlO3 and SrTiO3 substrates were used to evaluate processing. Pole projection and thin film diffraction measurements were used to establish grain orientation and verify structural integrity of the samples. Susceptibility magnetization, and transport measurements were used to evaluate the magnetic and electrical transport properties of the samples. Our results verified that an unfortunate consequence of processing is inherent changes to the internal structure of the material. This effect translates into modifications in the properties of the materials, and undesired feature that makes it very difficult to consistently predict material behavior. The results show that processing evaluation must incorporate a comprehensive understanding of the properties of the materials. Future studies will emphasize microstructural characteristics of the materials, in particular, those microscopic properties that map macroscopic behavior.

Hurley, John S.↗

NASA NTRS2000

Assessment of Low Cycle Fatigue Behavior of Powder Metallurgy Alloy U720

The fatigue lives of modem powder metallurgy disk alloys are influenced by variabilities in alloy microstructure and mechanical properties. These properties can vary as functions of variables the different steps of materials/component processing: powder atomization, consolidation, extrusion, forging, heat treating, and machining. It is important to understand the relationship between the statistical variations in life and these variables, as well as the change in life distribution due to changes in fatigue loading conditions. The objective of this study was to investigate these relationships in a nickel-base disk superalloy, U720, produced using powder metallurgy processing. Multiple strain-controlled fatigue tests were performed at 538 C (1000 F) at limited sets of test conditions. Analyses were performed to: (1) assess variations of microstructure, mechanical properties, and LCF failure initiation sites as functions of disk processing and loading conditions; and (2) compare mean and minimum fatigue life predictions using different approaches for modeling the data from assorted test conditions. Significant variations in life were observed as functions of the disk processing variables evaluated. However, the lives of all specimens could still be combined and modeled together. The failure initiation sites for tests performed at a strain ratio R(sub epsilon) = epsilon(sub min)/epsilon(sub max) of 0 were different from those in tests at a strain ratio of -1. An approach could still be applied to account for the differences in mean and maximum stresses and strains. This allowed the data in tests of various conditions to be combined for more robust statistical estimates of mean and minimum lives.

Gabb, Tomothy P.↗

NASA NTRS2002

Nanotube Reinforcement of Adhesively Bonded Joints

Over the past five years there has been much excitement about the development of nanotubes and nanofibers and the potential that these materials may offer in enhancing electrical and mechanical properties of systems. The purpose of this paper is to present research into improving the mechanical performance of polymers by using nanofibers as a reinforcement to make high performance composite materials. This paper will present theoretical predictions of the composite modulus and then present the actual performance of the composite. Fabrication details will be given along with photos of the microstructure. The matrix material is polymethylmethacrylate (PMMA) and the nanofibers are vapor-grown carbon nanofibers produced by Pyrograph Products, Inc.

Johnson, W. S.↗

NASA NTRS2003

Nanotube Reinforcement of Adhesively Bonded Joints

Johnson, W. S.↗

NASA NTRS1998

Microstructural Development of Directionally Solidified Hg(1-x)Zn(x)Se Alloys

Hg(1-x)Zn(x)Se alloys have been studied as an alternative to HgCdTe for the detection of electromagnetic radiation, because the shorter ZnSe and HgSe bonds were predicted to improve lattice stability. Previous studies showed that optical properties were stable with time and that the microhardness was higher than for HgTe based alloys. However, for this material to be commercially viable, compositional variations must be reduced, and the distribution of defects induced by the growth process must be understood. The basic structural properties of bulk materials were characterized, and dislocation etch pit densities were measured to determine whether the addition of Zn to the HgSe lattice reduced the potential for dislocation formation. Hg(0.9)Zn(0.1)Se alloys were directionally solidified using a modified Bridgman-Stockbarger method and in an applied magnetic field. Radial compositional variations were greatly reduced when solidification occurred in an applied magnetic field. The combination of a convex liquid-solid interface shape and a method for reduced wetting produced boules that were a single crystal after reaching full diameter. Observed surface features indicated ampoule wetting could be eliminated using a graphite getter. Microstructural characteristics were greatly improved over HgCdTe alloys, In six boules, a total of only one twin was observed, and no inclusions were found. A method for polishing and producing dislocation etch pits was developed for these alloys, revealing dislocation etch pit densities one to two orders of magnitude less than HgTe based alloys. A kink in the thermal profile during processing of one boule generated more dislocations than did lattice mismatch due to compositional variations. The results of this investigation indicate this alloy has improved microstructural properties and resistance to dislocation formation compared with similar II-VI alloys, and should be further investigated for the detection of electromagnetic radiation.

Cobb, S. D.↗

NASA NTRS1995

Observations of the magnetopause current layer: Cases with no boundary layer and tests of recent models

Evidence for the probable existence of magnetospheric boundary layers was first presented by Hones, et al. (1972), based on VELA satellite plasma observations (no magnetic field measurements were obtained). This magnetotail boundary layer is now known to be the tailward extension of the high-latitude boundary layer or plasma mantle (first uniquely identified using HEOS 2 plasma and field observations by Rosenbauer et al., 1975) and the low-latitude boundary layer (first uniquely identified using IMP 6 plasma and field observations by Eastman et al., 1976). The magnetospheric boundary layer is the region of magnetosheath-like plasma located Earthward of, but generally contiguous with the magnetopause. This boundary layer is typically identified by comparing low-energy (less than 10 keV) ion spectra across the magnetopause. Low-energy electron measurements are also useful for identifying the boundary layer because the shocked solar wind or magnetosheath has a characteristic spectral signature for electrons as well. However, there are magnetopause crossings where low-energy electrons might suggest a depletion layer outside the magnetopause even though the traditional field-rotation signature indicates that this same region is a boundary layer Earthward of the current layer. Our analyses avoided crossings which exhibit such ambiguities. Pristine magnetopause crossings are magnetopause crossings for which the current layer is well defined and for which there is no adjoining magnetospheric boundary layer as defined above. Although most magnetopause models to date apply to such crossings, few comparisons between such theory and observations of pristine magnetopause crossings have been made because most crossings have an associated magnetospheric boundary layer which significantly affects the applicable boundary conditions for the magnetopause current layer. Furthermore, almost no observational studies of magnetopause microstructure have been done even though key theoretical issues have been discussed for over two decades. This is because plasma instruments deployed prior to the ISEE and AMPTE missions did not have the required time resolution and most ISEE investigations to-date have focused on tests of MHD plasma models, especially reconnection. More recently, many phenomenological and theoretical models have been developed to explain the existence and characteristics of the magnetospheric boundary layers with only limited success to date. The cases with no boundary layer treated in this study provide a contrary set of conditions to those observed with a boundary layer. For the measured parameters of such cases, a successful boundary layer model should predict no plasma penetration across the magnetopause. Thus, this research project provides the first direct observational tests of magnetopause models using pristine magnetopause crossings and provides important new results on magnetopause microstructure and associated kinetic processes.

Eastman, Timothy E.↗

NASA NTRS1992

Creep fatigue life prediction for engine hot section materials (isotropic)

This Final Report covers the activities completed under the optional program of the NASA HOST Contract, NAS3-23288. The initial effort of the optional program was report-in NASA CR189221, which consisted of high temperature strain controlled fatigue tests to study the effects of thermomechanical fatigue, multiaxial loading, reactive environments, and imposed stresses. The baseline alloy used in the tests included B1900+Hf (with or without coating) and wrought INCO 718. Tests conducted on B1900+Hf included environmental tests using various atmospheres (75 psig oxygen, purified argon, or block exposures) and specimen tests of wrought INCO 718 included tensile, creep, stress rupture, TMF, multiaxial, and mean stress tests. Results of these testings were used to calibrate a CDA model for INCO 718 alloy and to develop modifications or corrections to the CDA model to handle additional failure mechanisms. The Socie parameter was found to provide the best correlation for INCO multiaxial loading. Microstructural evaluations consisting of optical, Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM) techniques, and surface replication techniques to determine crack initiation lives provided data which were used to develop life prediction models.

Nelson, R. S.↗

NASA NTRS1986

Ultrasonic characterization of microstructure in powder metal alloy

The ultrasonic wave propagation characteristics were measured for IN-100, a powder metallurgy alloy used for aircraft engine components. This material was as a model system for testing the feasibility of characterizing the microstructure of a variety of inhomogeneous media including powder metals, ceramics, castings and components. The data were obtained for a frequency range from about 2 to 20 MHz and were statistically averaged over numerous volume elements of the samples. Micrographical examination provided size and number distributions for grain and pore structure. The results showed that the predominant source for the ultrasonic attenuation and backscatter was a dense (approx. 100/cubic mm) distribution of small micropores (approx. 10 micron radius). Two samples with different micropore densities were studied in detail to test the feasibility of calculating from observed microstructural parameters the frequency dependence of the microstructural backscatter in the regime for which the wavelength is much larger than the size of the individual scattering centers. Excellent agreement was found between predicted and observed values so as to demonstrate the feasibility of solving the forward problem. The results suggest a way towards the nondestructive detection and characterization of anomalous distributions of micropores when conventional ultrasonic imaging is difficult. The findings are potentially significant toward the application of the early detection of porosity during the materials fabrication process and after manufacturing of potential sites for stress induced void coalescence leading to crack initiation and subsequent failure.

Tittmann, B. R.↗