Search NASA⌕ Search

SEARCH · Search NASA

Results for “monolayers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Surface sulfur measurements on stratospheric particles

The surface chemistries of three particulate samples collected from the lower stratosphere have been determined using a Scanning Auger Microprobe (SAM). These samples are typical of the most abundant natural and anthropogenic particles observed within the stratosphere in the greater-than-2-micron diameter size fraction. Succsessive sputtering and analysis below the first few adsorbed monolayers of all particles shows the presence of a thin (less than 150A) sulfur layer. These sulfur regions probably formed by surface reaction of sulfur-rich aerosols with each particle within the stratosphere. Settling rate calculations show that a typical sphere (10-micron diameter) may reside within the aerosol layer for 20 days and thus provide a qualitative guide to surface sulfur reaction rates.

Mackinnon, I. D. R.↗

Ring particles - Collisional interactions and physical nature

Attention is given to the properties of, and dynamical processes affecting individual particles of Saturn's rings. Because particles tend to be gravitationally bound when located on the surfaces of larger particles, and since net tidal stresses within the particles are small, particle collisions should produce accretion in Saturn's rings. Rapid accretionary processes within the rings are counterbalanced by tidal disruption of the larger accreted aggregates, which are presently designated 'dynamic ephemeral bodies'. The coefficient of restitution is probably very low, implying that the large particles containing most of the rings' mass are in a monolayer, although the small particles responsible for most of the rings' visible cross section form a layer many particles thick. Kinematic viscosity and interparticle erosive process models should incorporate these properties.

Weidenschilling, S. J.↗

Tilted CO on metal surfaces; CO/Pt(110), CO/Ni(110) and CO/Cu(100)

Tilting of CO at coverages greater than half a monolayer is considered as a mechanism for reducing the CO-CO repulsion. Qualitative agreement with the experiment for CO/Pt(110) is found, and a slightly smaller tilt for CO/Ni(110) is predicted. For CO/Cu(100), it is found that a bend of about 10 deg greatly reduces the repulsion.

Bauschlicher, C. W., Jr.↗

Emission FTIR analyses of thin microscopic patches of jet fuel residues deposited on heated metal surfaces

The relationship of fuel stability to fuel composition and the development of mechanisms for deposit formation were investigated. Fuel deposits reduce heat transfer efficiency and increase resistance to fuel flow and are highly detrimental to aircraft performance. Infrared emission Fourier transform spectroscopy was chosen as the primary method of analysis because it was sensitive enough to be used in-situ on tiny patches of monolayers or of only a few molecular layers of deposits which generally proved completely insoluble in any nondestructive solvents. Deposits of four base fuels were compared; dodecane, a dodecane/tetralin blend, commercial Jet A fuel, and a broadened-properties jet fuel particularly rich in polynuclear aromatics. Every fuel in turn was provided with and without small additions of such additives as thiophene, furan, pyrrole, and copper and iron naphthenates.

Lauer, J. L.↗

Photoenergy transduction in halobacterium halobium

The structure and function of a rhodopsin-like pigment bacteriorhodopsin, discovered and isolated from the membranes of the halophile Halobacterium halobium, were studied. Intermediatesm appearing in the cyclic photoreaction that drives the proton translocation, were spectroscopically characterized. The charge translocation in membrane monolayers and mulitlayers placed between electrodes were kinetically resolved. A model was developed for the proton translocation process, in which the isomerization of the retinal Schiff base decreases its pK to drive the proton off and simultaneaouly changes the connectivity from the cytoplasmic surface to the external surface. The stoichiometry of proton pumping in intact cells and the effect of the light generated electrochemical potential on the kinetics of the photoreaction cycle and the synthesis of ATP were investigated.

Stoeckenius, W.↗

The coverage-dependent effect on the barrier for oxygen penetration into a metal lattice

Model calculations for O/Cu(111) show that the rigid lattice penetration barrier is reduced from 8.2 to 5.3 eV as the O coverage is increased from 1/4 to 1/2 monolayer; it is expected that this large reduction will also apply to the relaxed lattice case. An increase of the distance between the first and second Cu layers, without changing the intralayer spacing, does not affect the barrier.

Bauschlicher, C. W., Jr.↗

Coverage dependent effects on metal surfaces - O, S, F, and Cl on Ni

The c(2 x 2) and p(2 x 2) vibrational frequencies for a rigid Ni lattice are computed for O, S, F, and Cl on Ni(100). It is found that only O/Ni(100) shows a large difference in rigid lattice vibrational frequency. A large shift in rigid lattice vibrational frequency is also found for O/Ni(111) between 0.25 and 0.5 monolayer coverages. Also associated with the change in coverage, is a change in the height above the surface R(perpendicular). This varies from a 0.11 A reduction for O/Ni(100), to an expansion of 0.06 A for F/Ni(100).

Bauschlicher, C. W., Jr.↗

Influence of preadsorbed oxygen on the sign and magnitude of the chemisorption-induced resistance change for H2 adsorption onto Fe films

Measurements have been made of the chemisorption-induced resistance change for H2 adsorbed onto Fe film substrates predosed with fixed coverages of chemisorbed oxygen. The measurements were made at temperatures from 295 to 340 K and for estimated oxygen coverages of less than 0.1 monolayers. Two distinct resistance change components were observed in both the adsorption kinetics and the equilibrium isotherms: a positive component which is associated with the adsorption of H2 onto a clean Fe surface, and a negative component which was correlated with the presence of the chemisorbed oxygen. The resistance change isotherms can be fit with a model which assumes that each of the resistance change components result from dissociative chemisorbed hydrogen. Possible mechanisms for the chemisorbed-oxygen-induced negative resistance change are discussed.

Shanabarger, M. R.↗

The velocity dispersion of the giant molecule clouds: A viscous origin

The observations of interstellar cloud motion show that the cloud velocity dispersion is nearly constant, to within a factor of 2, for clouds covering at least three orders of magnitude in mass. For example, the Giant Molecular Cloud (GMC) with typical masses of approx 5 x 10 to the 5th power solar masses have a one-dimensional planar, cloud-cloud, random velocity dispersion of approx 3-7 km/s. The HI clouds, of approx. 400 solar masses each, on the other hand, have a typical one-dimensional velocity dispersion of approx 6 km/s. Clearly, the clouds are not in kinetic energy equipartion. The GMC spatial distribution in the galactic disk is not that of an isolated, 3-D system; rather, the GMCs exhibit a very thin disk (approx nearly a monolayer) distribution; with the ratio of the diameter of a typical GMC to the vertical scale-height of the GMC distribution being approx 50 pc/150 pc = 0.3. The supernova shocks, which can accelerate the low mass clouds, are extremely ineffective in accelerating the GMCs because of the much larger mass/area ratio for the GMCs. The above points suggest that the GMCs do not constitute an isolated, 3-D system - rather, they indicate that the dynamics of the GMCs is mainly determined by the fact that they are located in a differentially rotating galactic disk, and that, as for particles in planetary rings, viscosity is the primary energy input. Specifically, it is proposed that gravitational scattering of the massive clouds off each other in the differentially rotating galactic disk constitutes an effective gravitational viscosity, which causes an increase in the random kinetic energy of the GMCs at the expense of their ordered, rotational kinetic energy.

Jog, C. J.↗

Thermodynamic state of SO2 on Io's surface

It has been suggested that surface conditions on Io might be conducive to significant SO2 adsorption on sulfur or alkali sulfides. A number of spectroscopic arguments for and against the high abundance of a SO2 adsorbate (versus frost) on Io have been made. SO2 absorption isotherms on particulate sulfur are measured, and the question of SO2 adsorbate/ice is approached from a thermodynamic perspective. Because of formidable experimental difficulties, data were not obtained at the very low temperatures and P(SO2) characteristics of Io; however, data were obtained over a wide range of pressures and temperatures somewhat higher than Io's and extrapolated to Io surface conditions. Errors in estimating adsorptive capacity accrue through extrapolation of the adsorption isotherms; however, more significant is the addition of the solid SO2 equilibrium vapor pressure curve to the phase diagram. The formation of ice places a strict upper limit on adsorptive coverage at any temperature. The limit for Io based upon the data is calculated, and it is shown that no more than 0.014 monolayers of SO2 can adsorb on sulfur at Io temperatures. Given the assumption that sulfur forms the primary adsorbent on Io's surface, or the assumption that the adsorptive capacity of the other adsorbents is not substantially greater than that of sulfur, this explains the fact that the nu(1) + nu(3) band center position is in better agreement with that of frost than adsorbate.

Zent, Aaron P.↗

Dose protraction studies with low- and high-LET radiations on neoplastic cell transformation in vitro

The effects of the low- and high-LET radiation (by X-rays, Co-60, and heavy ions) on the transformation of neoplastic cells were studied using cultured C3H10T1/2 mouse embryo cells. The transformed colonies in the confluent cell monolayers were recognized as focuses composed of highly polar fibroblastic multilayered criss-cross arrays of densely stained cells. For the low-LET radiation, there was a decrease in cell killing and cell transformation frequency when cells were irradiated with fractionated doses and at a low dose rate, indicating that cultured mammalian cells can repair both subtransformation and potential transformation lesions. No sparing effect, however, was found for the high-LET radiation. An enhancement of cell transformation was observed for low-dose/rate argon (400 MeV/u; 120 keV/micron) and iron particles (600 MeV/u; 200 keV/micron). The molecular mechanism for this enhancement effect is not known.

Yang, Tracy Chui-Hsu↗

Coadsorption of H2O and CO2 on the Martian surface

The adsorption of both CO2 and H2O was measured, under conditions of temperature and partial pressure similar to Mars, for a variety of absorbents. Both adsorb at coverages that exceed a monolayer at their respective Martian abundances. Clearly, their simultaneous presence in the Martian atmosphere will result in coadsorption of both at concentrations that may differ greatly from those measured during separate measurements. To the best of our knowledge, no data exists on the coadsorption of both gases. Co-adsorption experiments were begun and pertinent results will be reported. In the meantime the predicted behavior of such a system was mathematically explored as a compliment to the data, and to aid in its eventual interpretation.

Zent, A. P.↗

Applications of surface analysis and surface theory in tribology

Tribology, the study of adhesion, friction and wear of materials is a complex field which requires a knowledge of solid state physics, surface physics, chemistry, material science and mechanical engineering. It has been dominated, however, by the more practical need to make equipment work. With the advent of surface analysis and advances in surface and solid state theory, a new dimension has been added to the analysis of interactions at tribological interfaces. In this paper the applications of tribological studies and their limitations are presented. Examples from research at the NASA Lewis Research Center are given. Emphasis is on fundamental studies involving the effects of monolayer coverage and thick films on friction and wear. A summary of the current status of theoretical calculations of defect energetics is presented. In addition, some new theoretical techniques which enable simplified quantitative calculations of adhesion, fracture and friction are discussed.

Ferrante, John↗

Shear stress induced stimulation of mammalian cell metabolism

A flow apparatus was developed for the study of the metabolic response of anchorage dependent cells to a wide range of steady and pulsatile shear stresses under well controlled conditions. Human umbilical vein endothelial cell monolayers were subjected to steady shear stresses of up to 24 dynes/sq cm, and the production of prostacyclin was determined. The onset of flow led to a burst in prostacyclin production which decayed to a long term steady state rate (SSR). The SSR of cells exposed to flow was greater than the basal release level, and increased linearly with increasing shear stress. It is demonstrated that shear stresses in certain ranges may not be detrimental to mammalian cell metabolism. In fact, throughout the range of shear stresses studied, metabolite production is maximized by maximizing shear stress.

Mcintire, L. V.↗

The prediction and confirmation of critical epitaxial parameters

The coherency-incoherency transition in epitaxial crystals is said to take place at a critical misfit f(c) or, for a system in which a monolayer is subcritical, at a critical thickness h(c). In this paper, the physical principles and models used to predict critical parameters are analyzed and put into perspective. The dependence of the relevant principles on the equilibrium-nonequilibrium conditions under which the quantities are measured in practice is stressed. The advantages and disadvantages of the models used (essentially the Frenkel-Kontorowa and Volterra models) are highlighted.

Van Der Merwe, Jan↗

On the temperature of surfaces

The concept of the temperature of a surface is introduced from the viewpoint of the physical chemistry of surfaces. The surface, near surface and microlayer regions of the interface are defined. Most methods measure the temperature of the microlayer or at best the near surface region and may err in representing the surface temperature. Methods based on capillary ripples actually measure the surface temperature since surface tension (or surface tension tensor when a monolayer has been spread or absorbed at the interface) is the main restoring force that controls their propagation. Light scattering methods are described for determining the elevation of very small amplitude capillary waves through the computation of various correlation functions from which the surface tension can be estimated. Procedures for estimating the surface temperature are described.

Mann, J. Adin, Jr.↗

ISS and TPD study of the adsorption and interaction of CO and H2 on polycrystalline Pt

The adsorption and interaction of CO and H2 on polycrystalline Pt has been studied using ion scattering spectroscopy (ISS) and temperature programmed desorption (TPD). The ISS results indicate that the initial CO adsorption on Pt takes place very rapidly and saturates the Pt surface with coverage close to a monolayer. ISS also shows that the CO molecules adsorb at an angular orientation from the surface normal and perhaps parallel to the surface. A TPD spectrum obtained after coadsorbing C-12 O-16 and C-13 O-18 on Pt shows no isotopic mixing, which is indicative of molecular CO adsorption. TPD spectra obtained after coadsorbing H2 and CO on polycrystalline Pt provides evidence for the formation of a CO-H surface species.

Melendez, Orlando↗

MBE growth technology for high quality strained III-V layers

The III-V films are grown on large automatically perfect terraces of III-V substrates which have a different lattice constant, with temperature and Group III and V arrival rates chosen to give a Group III element stable surface. The growth is pulsed to inhibit Group III metal accumulation of low temperature, and to permit the film to relax to equilibrium. The method of the invention: (1) minimizes starting step density on sample surface; (2) deposits InAs and GaAs using an interrupted growth mode (0.25 to 2 monolayers at a time); (3) maintains the instantaneous surface stoichiometry during growth (As-stable for GaAs, In-stable for InAs); and (4) uses time-resolved RHEED to achieve aspects (1) through (3).

Grunthaner, Frank J.↗