Search NASA⌕ Search

SEARCH · Search NASA

Results for “periodic substrate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Thermal Conductivity and Stability of HfO2-Y2O3 and La2Zr2O7 Evaluated for 1650 Deg C Thermal/Environmental Barrier Coating Applications

HfO2-Y2O3 and La2Zr2O7 are candidate thermal and environmental barrier coating (T/EBC) materials for gas turbine ceramic matrix composite (CMC) combustor applications because of their relatively low thermal conductivity and high temperature capability. In this paper, thermal conductivity and high temperature stability of hot-pressed and plasma sprayed specimens with representative partially-stabilized and fully-cubic HfO2-Y2O3 compositions and La2Zr2O7 were evaluated at temperatures up to 1700 C using a steady-state laser heat-flux technique. Sintering behavior of the plasmasprayed coatings was determined by monitoring the thermal conductivity increases during a 20-hour test period at various temperatures. Durability and failure mechanisms of the HfO2-Y2O3 and La2Zr2O7 coatings on mullite/SiC hexoloy or SiC/SiC CMC substrates were investigated at 1650 C under thermal gradient cyclic conditions. Coating design and testing issues for the 1650 C thermal/environmental barrier coating applications are also discussed.

Zhu, Dong-Ming↗
DOE OSTI2023

Carbonation dynamics of hydrated alite revealed by electron microscopy

CO 2 sequestration in concrete is crucial to relieve the environmental burden, while the carbonation mechanisms remain unclear. Here, we explored the carbonation dynamics of alite hydrates through electron microscopy. We discovered that calcite is the main phase of carbonate crystals throughout the entire carbonation period in the alite system. Further, the shape evolution of calcite crystals was captured: spindle carbonates initially formed on C-S-H substrate and then transformed into rhombohedrons; Intermediate states such as polyhedral particles and layered rhomboids were also observed. Based on our quantitative calculations, the growth rate of calcite particles was determined approximately 0.2 μm/day, which may be affected by the relative concentration between calcium ions and CO 2 source. A direct relation between the microstructure and mechanical properties of calcite was uncovered using atomic force microscopy. Furthermore, we found that the morphology development of calcite crystals during carbonation may be explained by the surface energy variation of different facets. This work suggests a unique approach to track carbonation kinetics and provides new opportunities to unveil underlying carbonation mechanisms at the nanoscale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Reduced Dislocation Introduction in III–V/Si Heterostructures with Glide-Enhancing Compressively Strained Superlattices

The novel use of a GaAs y P 1-y /GaP compressively-strained superlattice (CSS) to provide enhanced control over misfit dislocation (MD) evolution and threading dislocation density (TDD) during GaP/Si metamorphic heteroepitaxy is demonstrated. Here, the insertion of the CSS just after critical thickness, and thus prior to substantial dislocation introduction, is found to yield significantly reduced TDD in relaxed, 500 nm thick, n-type GaP/Si versus comparable control samples. The impact of CSS period count on average TDD and the overall dislocation network morphology was examined, supported by quantitative microstructural characterization, revealing a nearly 20× relative TDD reduction (to 2.4 ± 0.4×10 6 cm -2 ) with a 3-period CSS structure. A similarly low TDD (3.0 ± 0.6×10 6 cm -2 ) is maintained when the resultant n-GaP/Si virtual substrate is used for the growth of a subsequent n-type GaAs 0.75 P 0.25 -terminal GaAs y P 1-y step-graded metamorphic buffer. Although the physical mechanism for TDD reduction provided by these structures is not yet entirely understood, this initial work suggests that enhanced glide dynamics of MDs at or within the CSS placed early in the growth leads to a reduction in the total number of dislocations introduced overall, as opposed to annihilation-based reduction that occurs in conventional strained-layer superlattice dislocation filter approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Dynamic Carrier Modulation via Nonlinear Acoustoelectric Transport in van der Waals Heterostructures

Dynamically manipulating carriers in van der Waals heterostructures could enable solid-state quantum simulators with tunable lattice parameters. A key requirement is the formation of deep potential wells to reliably trap excitations. Here, we report the observation of nonlinear acoustoelectric transport and dynamic carrier modulation in boron nitride-encapsulated graphene devices coupled to intense surface acoustic waves (SAWs) on LiNbO 3 substrates. SAWs generate strong acoustoelectric current densities ( J AE ), transitioning from linear to nonlinear regimes with increasing SAW intensity. In the nonlinear regime, periodic carrier (electrons, holes, or their mixtures) stripes emerge. Using counter-propagating SAWs, we create standing SAWs (SSAWs) to dynamically manipulate charge distributions without static gates. The saturation of J AE , attenuation transitions, and tunable resistance peaks confirms strong carrier localization. Finally, these results establish SAWs as a powerful tool for controlling carrier dynamics in two-dimensional (2D) materials, paving the way for the development of time-dependent quantum systems and acoustic lattices for quantum simulation.

2D materials↗
DOE OSTI2023

Spatial Study 2022: Surface Water Samples, Cotton Strip Degradation, and Hydrologic Sensor Data across the Yakima River Basin, Washington, USA (v3)

This dataset supports a broader study examining the drivers of spatial variability in sediment respiration rates in the Yakima River Basin. The dataset provides data and photos generated from sample collection during the same one-week period at 48 sites within multiple rivers throughout the Yakima River Basin in Washington, USA. The contents include surface water geochemistry data; river substrate grain size photos; stream depth data; manual chamber open channel respiration data; and field metadata (including qualitative information on instream and river corridor characteristics). Grain size photos can be used to improve estimates of channel substrate D50 data. The dataset also includes tensile strength and photos from cotton strip field degradation experiments; five-week sensor time series temperature, dissolved oxygen, pressure, pH, specific conductance, chlorophyll A, and turbidity data; plots of the sensor data; and R scripts used to generate the plots. Samples collected during this study were labeled as “Second Spatial Study” or “SSS.” A subset of data from the SSS samples were published in the contiguous United States (CONUS)-Scale Model-Sample (CM) study data package available at https://data.ess-dive.lbl.gov/view/doi:10.15485/1923689 that presents data from across the CONUS. SSS data published in the CM data package were not included in this data package. They include dissolved organic carbon (DOC, measured as non-purgeable organic carbon, NPOC), total nitrogen (TN), grain size, aerobic sediment respiration, dissolved oxygen (DO), and temperature. Parent IDs and Site IDs are consistent between the SSS and CM data packages, and they can be mapped directly so data across packages can be used together. Additionally, sensor data from a similar 2021 spatial study can be found at https://data.ess-dive.lbl.gov/view/doi:10.15485/1892052 and 2021 sample data can be found at https://data.ess-dive.lbl.gov/view/doi:10.15485/1898914. The 2021 spatial study had some sites in common with this 2022 spatial study. This dataset is comprised of three photo folders and one main data folder with six subfolders. The photo folders contain photographs and videos of cotton strip retrieval and sediment quadrats. The main data folder consists of (1) file-level metadata; (2) data dictionary; (3) field metadata; (4) total suspended solids (TSS) data and cotton strip tensile strength data and averages; (5) field protocol; (6) readme; (7) methods codes; (8) international generic sample number (IGSN) mapping file; (9) sensor installation methods summary; (10) stream depth and averages; and (11) Ultrameter data and averages. The Sonar subfolder consists of Sonar time-series depth data and a processing script. The BarotrollAtm, DepthHOBO, MantaRiver, miniDOT, and miniDOTManualChamber subfolders contain time-series data, plots, and summary files. All files are .csv, .pdf, .txt, .R, .Rmd, .jpg, .jpeg, .AVI, .mp4, or .mov. The data package was originally published in April 2023. It was updated in August 2023 (v2; modified files) and September 2024 (v3; modified files). See the change history section in the readme for details. We acknowledge the Yakama Nation as owners and caretakers of the lands where we collected these data. We thank the Confederated Tribes and Bands of the Yakama Nation Tribal Council and Yakama Nation Fisheries for working with us to facilitate sample collection and optimization of data usage according to their values and worldview.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Removable, Sequestration Coatings for Mitigating Hazardous Contaminants Related to Deactivation and Decommissioning Activities

This project is a collaborative effort between InnoSense LLC (ISL) and Oak Ridge National Laboratory (ORNL) aimed at mitigating the mercury (Hg) contamination problem at the Y-12 National Security Complex (NSC). The report summarizes the research and technology development work of the Phase IIB Project, led by Dr. Uma Sampathkumaran at ISL for the period of July 31, 2017–October 31, 2021. The Y-12 site cleanup includes technologies for safe and cost-effective facility demolition, soil remediation, and on-site treatment and disposal of mercury bearing wastes. One of the technology demonstration goals was a reactive strippable coating for targeted pre-demolition and de-contamination to limit Hg mobilization and the volume of debris requiring treatment for disposal. Toward this, ISL has developed a water-based reactive strippable coating (Trap & See-Hg™) to sequester elemental Hg(0) and mercuric Hg(II) species in the coating. The coating provides multiple benefits including (1) Hg vapor suppression, (2) sealing in the hazardous contaminants, (3) visually locating the contaminant through color changes, and (4) remediating the contaminated surfaces upon coating removal. Through collaboration between ORNL and ISL in Phase II work, the team successfully demonstrated the Trap & See-Hg technology to (1) visually locate the presence of Hg on concrete, soil and drywall surfaces, (2) effectively sequester all mercury species (elemental, soluble and insoluble Hg) from lab-generated and ex-situ soil and brick/rubble samples collected from the Y 12 site with 80 to 95% efficiency to capture/reduce Hg vapor concentration, (3) be applied by manual and robotic spray applicators and cure at room ambient, (4) remain a cohesive and peelable coating upon drying, and (5) sequester Hg0 from walls in the alpha-2 building basement at Y-12 during a small scale in-situ field trial. In Phase IIB, ISL’s effort was focused on refining the coating formulations with additives containing passive and reactive sorbents, colorimetric indicator, and thixotropic agents to achieve the desired performance. The paints were then evaluated at ORNL for applicability to metal and concrete surfaces of different sizes and shapes, and soil rubble, Hg-sorption capacity and achieving sag-free coating on surfaces when applied by a manual spray applicator. Ambient cure of the coating resulted in a dry thickness of 16–20 mil. The coatings were removed from smooth or rough surfaces with low to moderate force. Both lab-generated Hg-contaminated samples and soil and brick/rubble samples containing a range of Hg concentrations (collected from the Y-12 site by UCOR) were used in this project. Optimized formulations were applied to these samples and evaluated for ability to suppress Hg vapors, sequester Hg 0 and Hg(II) species and color mapping of mercury species on the test surface. The ORNL team initially identified three to four potential sites at Y-12 and ORNL for potential demonstration. However, the pandemic closed any possible avenues for on-site demonstration of the robotic spray applicator. The metal and concrete samples with low to high Hg content provided by UCOR from an ongoing demolition were subsequently used for ex-situ sample characterization and analysis at ORNL over a period of 25 days. The coatings suppressed Hg vapors with an efficiency of 95–99% from heavily contaminated metal and 60% from concrete substrate. Analysis of total Hg in the peeled paints indicates sorption capacities ranging from 12 µg Hg/g of paint from concrete to 1.2 mg Hg/g of paint from the metal substrates while peeled paints from soil samples could capture a total Hg from 2.3 mg Hg/g to 66 mg/g paint. Toxicity characteristic leaching procedure (TCLP) tests recovered total mercury leached at 0.15±0.0008 µg/L for concrete to 126.81±0.67 µg/L and 377.25±5.67 µg/L for the two metal substrates, to allow for informed decisions on downstream disposal considerations. Together, this Phase IIB demonstrated the potential value of the Trap & See-Hg for Hg uptake, vapor suppression, and color mapping, and may thus be used to enhance worker safety during site cleanup, facility demolition, and downstream waste disposal at Y-12 NSC.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Dual‐Scale Nanostructures via Evaporative Assembly

Abstract Dual‐scale hierarchical structures with regular microscale patterns and varying degree of nanoscale crystalline order are synthesized on physically and chemically homogeneous substrates by evaporative self‐assembly with a suspension of DNA‐functionalized nanoparticles (NPs) with a charged core shell. For a certain NP concentration range, periodic concentric rings in a stripe‐like micropattern are produced over macroscale surface areas by an NP monolayer with hexagonal lattice structure at the nanoscale. The stripe width, spacing, and nanoparticle ordering can be controlled by varying the NP concentration. The results indicate that the interplay between “stick‐slip” motion of the droplet contact line and coulombic and steric NP interactions control the formation of the observed structures. A simple analytical model is proposed to account for the experimental observations and guide the future design of different nanostructure morphologies. This work demonstrates a simple cost‐effective mask‐free method for fabricating large‐area nanostructured 2D materials and metasurfaces for applications ranging from energy conversion/storage to optoelectronics and nanophotonics.

Srivastava, Sunita↗
NASA NTRS1982

Large area silicon sheet by EFG

Work carried out on the JPL Flat Plate Solar Array Project, for the purpose of developing a method for silicon ribbon production by Edge-defined Film-fed Growth (EEG) for use as low-cost substrate material in terrestrial solar cell manufacture, is described. A multiple ribbon furnace unit that is designed to operate on a continuous basis for periods of at least one week, with melt replenishment and automatic ribbon width control, and to produce silicon sheet at a rate of one square meter per hour, was constructed. Program milestones set for single ribbon furnace operation to demonstrate basic EEG system capabilities with respect to growth speed, thickness and cell performance were achieved for 10 cm wide ribbon: steady-state growth at 4 cm/min and 200 micron thickness over periods of an hour and longer was made routine, and a small area cell efficiency of 13+% demonstrated. Large area cells of average efficiency of 10 to 11%, with peak values of 11 to 12% were also achieved. The integration of these individual performance levels into multiple ribbon furnace operation was not accomplished.

Kalejs, J. P.↗
NASA NTRS1988

Moisture interaction and stability of ZOT (Zinc Orthotitanate) thermal control spacecraft coating

Two of the many performance requirements of the zinc orthotitanate (ZOT) ceramic thermal control paint covering parts of the Jupiter-bound Galileo spacecraft are that it be sufficiently electrically conductive so as to prevent electrostatic discharge (ESD) damage to onboard electronics and that it adhere to and protect the substrate from corrosion in terrestrial environments. The bulk electrical resistivity of ZOT on an aluminum substrate was measured over the ranges 22 C to 90 C and 0 percent RH to 100 percent RH, and also in soft (10 (minus 2) Torr) and hard (10 (minus 7) Torr) vacuums. No significant temperature dependence was evident, but measured resistivity values ranged over 9 orders of magnitude: 10 to the 5th power ohm-cm at 100 percent RH greater than 10 to the 12th power ohm-cm in a hard vacuum. The latter value violates the ESD criterion for a typical 0.019 cm thick coating. The corrosion study involved exposing typical ZOT substrate combinations to two moisture environments - 30 C/85 percent RH and 85 C/85 percent RH - for 2000 hours, during which time the samples were periodically removed for front-to-back electrical resistance and scratch/peel test measurements. It was determined that the ZOT/Al and ZOT/Mg systems are stable (no ZOT delamination), although some corrosion (oxide formation) and resistivity increases observed among the ZOT/Mg samples warrant that exposure of some parts to humid environments be minimized.

Mon, Gordon R.↗
NASA NTRS1993

Ellipsometric study of ambient-produced overlayer growth rate on YBa2Cu3O(7-x) films

An ellipsometric study of ambient-reaction-produced BaCO3 overlayer growth on laser-ablated YBCO is presented as a function of time. The effects of the anisotropy of YBCO on the ellipsometric data inversion process are discussed, and it is concluded that with certain restrictions on the data acquisition method, the anisotropic substrate can be adequately modeled by its isotropic pseudodielectric function for the purpose of overlayer thickness estimation. It is found that after an initial period of rapid growth attributed to the chemical reaction of the exposed surface bonds, the BaCO3 overlayer growth is linear at 1-2 A per day. This slow growth rate is attributed to the complexity of the BaCO3-forming reaction, together with the need for ambient reactants to diffuse through the overlayer.

Sieg, Robert M.↗
DOE OSTI2022

Robust silane self-assembled monolayer coatings on plasma-engineered copper surfaces promoting dropwise condensation

Dropwise condensation is well known to result in better heat transfer performance owing to efficient condensate/droplet removal, which can be harnessed in various industrial heat/mass transfer applications such as power generation and conversion, water harvesting/desalination, and electronics thermal management. The key to enhancing condensation via the dropwise mode is thin low surface energy coatings (<100 nm) with low contact angle hysteresis. Ultrathin (<5 nm) silane self-assembled monolayers (or SAMs) have been widely studied to promote dropwise condensation due to their minimal thermal resistance and scalable integration processes. Such thin coatings typically degrade within an hour during condensation of water vapor. After coating failure, water vapor condensation transitions to the inefficient filmwise mode with poor heat transfer performance. We enhance silane SAM quality and durability during water vapor condensation on copper compared to state-of-the-art silane coatings on metal surfaces. We achieve this via (i) surface polishing to sub-10 nm levels, (ii) pure oxygen plasma surface treatment, and (iii) silane coating integration with the copper substrate in an anhydrous/moisture-free environment. The resulting silane SAM has low contact angle hysteresis (≈20°) and promotes efficient dropwise condensation of water for >360 hours without any visible sign of coating failure/degradation in the absence of non-condensable gases. We further demonstrate enhanced heat transfer performance (≈5-7× increase over filmwise condensation) over an extended period of time. Surface characterization data post-condensation leads us to propose that in the absence of non-condensable gases in the vapor environment, the silane SAM degrades due to reduction and subsequent dissolution of copper oxide at the oligomer-substrate interface. The experiments also indicate that the magnitude of surface subcooling (or condensation rate) affects the rate of coating degradation. Finally, this work identifies a pathway to durable dropwise promoter coatings that will enable efficient heat transfer in industrial applications.

42 ENGINEERING↗
NASA NTRS1995

Growth and Analysis of Highly Oriented (11n) BCSCO Films for Device Research

Films of BCSCO superconductor of the type Bi2CaSr2Cu2O(x), have been grown by liquid phase epitaxy method (LPE), using a partially closed growth chamber. The films were grown on (001) and (110) NdGaO3 substrates by slow cooling process in an optimized temperature range below the peritectic melting point (880 C) of Bi2CaSr2Cu2O8. Optimization of parameters, such as seed rotation, soak of initial growth temperature and growth period results in the formation of 2122 phase BCSCO films. The films grown at rotation rates of less than 30 and more than 70 rpm are observed to be associated with the second phase of Sr-Ca-Cu-O system. Higher growth temperatures (greater than 860 C) also encourage to the formation of this phase. XRD measurements show that the films grown on (110) NdGaO3 have a preferred (11n)-orientation. It is pertinent to mention here that in our earlier results published elsewhere we obtained c-axis oriented Bi2CaSr2Cu2O8 phase films on (001) NdGaO3 substrate. Critical current density is found to be higher for the films grown on (110) than (001) NdGaO3 substrate orientation. The best values, zero resistance (T(sab co)) and critical current density obtained are 87 K and 10(exp 5) A/sq cm respectively.

Raina, K. K.↗
NASA NTRS1995

Growth and analysis of highly oriented (11n) BCSCO films for device research

Films of BCSCO superconductor of the type Bi2CaSr2Cu2Ox have been grown by liquid phase epitaxy method (LPE), using a partially closed growth chamber. The films were grown on (001) and (110) NdGaO3 substrates by slow cooling process in an optimized temperature range below the peritectic melting point (880 C) of Bi2CaSr2Cu2O8. Optimization of parameters, such as seed rotation, soak of initial growth temperature and growth period results in the formation of 2122 phase BCSCO films. The films grown at rotation rates of less than 30 and more than 70 rpm are observed to be associated with the second phase of Sr-Ca-Cu-O system. Higher growth temperatures (is greater than 860 C) also encourage to the formation of this phase. X-Ray Diffraction (XRD) measurements show that the films grown on (110) NdGaO3 have a preferred (11 n)-orientation. It is pertinent to mention here that in our earlier results published elsewhere we obtained c-axis oriented Bi2CaSr2Cu2O8 phase films on (001) NdGaO3 substrate. Critical current density is found to be higher for the films grown on (110) than (001) NdGaO3 substrate orientation. The best values of zero resistance (T(sub co)) and critical current density obtained are 87 K and 105 A/sq cm, respectively.

Raina, K. K.↗
NASA NTRS1987

Material growth and characterization for solid state devices

During this period InGaAs and InGaAsP were grown on (100)InP by liquid phase electroepitaxy (LPEE). Results of the epitaxial growth of InGaAs on sputtered quartz masked substrates are presented. The resulting surface morphology can be related to the current density distribution near the edges of a masked pattern. The quaternary InGaAs was grown with compositions corresponding to 1.3 micron and 1.5 micron emission wavelengths. Growth rates were found to be linearly dependent upon current density, and a strong dependence upon composition was noted. These compositions lie in the miscibility gap region of the alloy phase diagram at the 645 C growth temperature. Growths were performed at 685 C to avoid the miscibility gap. Epilayers were characterized by photoluminescence, X-ray diffraction, secondary ion mass spectrometry, and Hall effect measurements. Aluminum oxide was deposited on silicon and InGaAs substrates for the characterization of this material as an insulator in a field effect transistor structure. It was determined that the results did not warrant further work with the deposition from an aluminum isopropoxide source. A metallographic vapor phase epitaxy system installation is nearing completion for use in hybrid III-V semiconductor epilayer growths.

Collis, Ward J.↗
DOE OSTI2026

Evolution of Electronic Properties of Graphene Nanoribbons with Progressive Carving: From Straight to Porous to Chevron Ribbons

Graphene nanoribbons (GNRs) are highly versatile materials due to their unique electronic, magnetic, and optical properties, which can be precisely tuned by controlling their width, edge structure, and topology. Here, we report the on-surface synthesis and characterization of a straight N = 15 armchair GNR with periodic annulene nanopores (15-pGNR). It serves as a structural link between two well-established GNRs: the pristine N = 15 armchair GNR without pores (15-AGNR) and the chevron GNR (cGNR). With the addition of the 15-pGNR reported in this study, these three GNRs form a rare experimentally accessible series of ribbons, in which the evolution of electronic properties can be tracked upon progressive carving of a basic 15-AGNR: first, by creating periodic nanopores to form 15-pGNR and then by extending the pore area and producing meandering cGNR. We have designed a molecular precursor for the 15-pGNR and grown the nanoribbons on single-crystal gold substrates by on-surface synthesis in ultra-high vacuum (UHV) conditions. The atomically precise structure of 15-pGNR was confirmed by scanning tunneling microscopy (STM) and non-contact atomic force microscopy (nc-AFM). The band gap of 15-pGNR was studied by scanning tunneling spectroscopy (STS) and dI/dV mapping, and the occupied electronic levels were investigated by angle-resolved photoemission spectroscopy (ARPES). A theoretical and experimental comparison of 15-pGNRs, 15-AGNRs, and cGNRs demonstrates that the introduction of periodic nanopores into 15-AGNR leads to a more than 2-fold increase in its band gap. In contrast, the band gaps of 15-pGNR and cGNR differ only by about 15%. Such band gap increase can be qualitatively understood to arise from two combined effects, the periodic perforation of the graphene lattice and the confinement effect induced by the GNR width.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Achieving high hydrogen productivities of 20 L/L-day via microbial electrolysis of corn stover fermentation products

Microbial electrolysis cells have the potential to generate renewable hydrogen from underused waste streams, however current devices have not reached very large productivity targets using real waste products at any scale. This study used a waste from fermented corn stover known as corn stover fermentation product to reach performance metrics that could be commercialized, if adequately scaled. Average current densities in MECs with mature biofilms reached 17.9 +/- 1.6 A/m 2 at an organic loading rate of 30 grams of chemical oxygen demand per liter of anode volume per day (g/L-day), reaching a maximum current density of 27.2 +/- 2.9 A/m 2 . Hydrogen productivities reached 20.2 +/- 2.0 L of H 2 per L anode volume per day (L/L-day). These represent the highest current densities and highest hydrogen productivities using a complex feedstock in a microbial electrolysis cell. Organic acids and sugars present in untreated substrate were converted at high percentages in MECs, with most above 90% conversion, at organic loading rates of 10, 20, and 30 g/L-day. The effect of periodic high liquid flow rates through the anode on performance was assessed. These tests, called pulsing, showed that hydrogen productivities and current densities increased most dramatically as flow was pulsed every hour at a baseline flow rate of 0.3 mL/min. These productivities show promise for high performance systems, if adequate scale up can be achieved.

09 BIOMASS FUELS↗
DOE OSTI2020

Programmable topotaxis of magnetic rollers in time-varying fields

We discuss how spatially uniform, time-periodic magnetic fields can be designed to power and direct the migration of ferromagnetic spheres up (or down) local gradients in the topography of a solid substrate. Our results are based on a dynamical model that considers the time-varying magnetic torques on the particle and its motion through the fluid at low Reynolds number. We use both analytical theory and numerical simulation to design magnetic fields that maximize the migration velocity up (or down) an inclined plane. We show how “topotaxis” of spherical particles relies on differences in the hydrodynamic resistance to rotation about axes parallel and perpendicular to the plane. Importantly, the designed fields can drive multiple independent particles to move simultaneously in different directions as determined by gradients in their respective environments. Experiments on ferromagnetic spheres provide evidence for topotactic motions up inclined substrates. The ability to program the autonomous navigation of driven particles within anisotropic environments is relevant to the design of colloidal robots.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1980

Progress in the growth of wide silicon ribbons by the EFG technique at high speed using multiple growth stations

We report here progress in a program designed to examine the feasibility of large scale production of low-cost silicon sheet substrates for solar cells by the EFG process. A multiple-ribbon EFG station, containing five single-ribbon cartridges, has been continuously operated for a period of 15 hours at a duty cycle of 94%. The average width of the ribbon grown was 5 cm, and the average growth speed was 3.4 cm/min. The cartridge concept of ribbon growth has been extended to successfully grow 10 cm wide ribbon at speeds up to 4 cm/min. Large area (approximately 50 sq cm) solar cells with efficiencies in the range from 8% to 11% (AM1) have been made from ribbon grown in the cartridge systems.

Kalejs, J. P.↗