Search NASA⌕ Search

SEARCH · Search NASA

Results for “polyesters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Nondestructive determination of fatigue crack damage in composites using vibration tests.

The vibration response of glass reinforced epoxy and polyester laminates was investigated. The complex modulus and the damping capacity were measured as fatigue crack damage accumulated. Changes in the Young's modulus as well as the damping capacity correlated with the amount of crack damage. The damping was especially sensitive to debonding of the reinforcement from the resin matrix. Measurement of these vibration response changes shows promise as a means to nondestructively test the structural integrity of filament-reinforced composite structural members.

Dibenedetto, A. T.↗
NASA NTRS1971

Binder model system to be used for determination of prepolymer functionality

Development of a method for determining the functionality distribution of prepolymers used for rocket binders is discussed. Research has been concerned with accurately determining the gel point of a model polyester system containing a single trifunctional crosslinker, and the application of these methods to more complicated model systems containing a second trifunctional crosslinker, monofunctional ingredients, or a higher functionality crosslinker. Correlations of observed with theoretical gel points for these systems would allow the methods to be applied directly to prepolymers.

Martinelli, F. J.↗
NASA NTRS1973

The GSFC cosmic radiation experiment for the Pioneer F/G Jupiter mission

The extremely lightweight, low power design of the cosmic radiation experiment is obtained by using less than 10 percent of the total weight for the mechanical system. Both the baseplate and the top plate are aluminum honeycomb, the side panels are magnesium trusswork, and the inside circuitry is stacked like a sandwich and interleaved with polyester urethane foam for vibration damping. The flight performance of the experimental hardware is excellent.

Trainor, J. H.↗
NASA NTRS1974

Production development of organic nonflammable spacecraft potting, encapsulating and conformal coating compounds. Volume 1: Discussion, figures, and references

Based upon extensive contacts with vendors, a broad array of non-flammable polymeric specie, and additives generally noted to have flame retarding properties, were considered. The following polymeric matrices were examined: modified silicone and fluorosilicone RTV's polyesters, epoxies, urethanes, and epoxy-urethanes. Optimization of formulations to obtain a suitable balance between the various properties and flammability resistance led to the final selection of a silicone RTV/additive-loaded compound which meets almost all program requirements. The very low valued properties found are within a realistic level of design toleration. Complete formulation, processing, and test data is provided for this compound, EPOCAST 87517-A/B, and the other formulations prepared by the project. Details of those test methods are presented along with procedures utilized in the program. In addition, a description of the special flammability facility previously designed and then modified for this program is also presented.

Lieberman, S. L.↗
NASA NTRS1974

Anechoic chamber in industrial plants

A light anechoic chamber for routine acoustical measurements in the machine building industry is reported. The outer housing of the chamber consists of modules cast in glass fiber reinforced polyester resin; the inner housing consists of pyramidal modules cut out of sound absorbing slates. The parameters of this anechoic chamber facilitate acoustical measurements according to ISO and CAEM recommendations.

Halpert, E.↗
NASA NTRS1974

Apparatus for forming drive belts

An apparatus for manufacturing belts, such as seamless belts, is provided, the apparatus has relatively movable rollers that are mounted in an oven. A belt blank, for example, of a thin polyester film, is rotated on the rollers as heat is applied. Four rollers, each mounted on a separate roller assembly, are movable along appropriate tracks while a fifth centrally located roller is stationary. A pair of dc motors are operatively connected to a speed reduction gear assembly to provide a pair of rotating drive shafts that extend into the oven. One rotating shaft drives all of the rollers through a rotational gear assembly while the other drive shaft is capable of positioning the movable rollers through respective rotating threaded shafts. Control devices are provided for controlling the motors while measuring devices are operatively connected to the positional drive shaft to indicate the position of the rollers.

Topits, A., Jr.↗
NASA NTRS1973

Shuttle active thermal control system development testing. Volume 7: Improved radiator coating adhesive tests

Silver/Teflon thermal control coatings have been tested on a modular radiator system projected for use on the space shuttle. Seven candidate adhesives have been evaluated in a thermal vacuum test on radiator panels similar to the anticipated flight hardware configuration. Several classes of adhesives based on polyester, silicone, and urethane resin systems were tested. These included contact adhesives, heat cured adhesives, heat and pressure cured adhesives, pressure sensitive adhesives, and two part paint on or spray on adhesives. The coatings attached with four of the adhesives, two silicones and two urethanes, had no changes develop during the thermal vacuum test. The two silicone adhesives, both of which were applied to the silver/Teflon as transfer laminates to form a tape, offered the most promise based on application process and thermal performance. Each of the successful silicone adhesives required a heat and pressure cure to adhere during the cryogenic temperature excursion of the thermal-vacuum test.

Reed, M. W.↗
NASA NTRS1974

Testing of flat conductor cable to Underwriters Laboratory standards UL719 and UL83

The flat conductor cable (FCC) which was tested consisted of three AWG No. 12 flat copper conductors laminated between two films of polyethylene terephthalate (Mylar) insulation with a self-extinguishing polyester adhesive. Results of the tests conducted on this cable, according to specifications, warrants the use of this FCC for electrical interconnections in a surface nonmetallic protective covering.

Loggins, R. W.↗
NASA NTRS1975

A study of the effects on mice of smoke and gases from controlled fires in simulated aircraft cabins

Male Swiss albino mice were exposed to the pyrolysis products of two fire-retardant materials, a chlorinated aromatic polyamide and a copolymer of vinylidine fluoride and hexafluoropropene. Comparison tests were made with cotton and a 50/50 cotton-polyester composite. In addition, tests were conducted under the presence of CO, and mice were injected intraperitoneally or intramuscularly with aqueous solutions containing dissolved effluents from the pyrolysis of cotton or of chlorinated aromatic polyamide. Results indicate that unique thermodecomposition products of the polymeric materials are more toxic to mice than are other products from cotton under similar controlled conditions.

Moreci, A. P.↗
NASA NTRS1976

Testing flat-conductor cable

Report describes characteristics of type of FCC which consists of three AWG No. 12 flat copper conductors laminated between two films of polyethylene terephthalate (Mylar) insulation with self-extinguishing polyester adhesive.

Loggins, R. W.↗
NASA NTRS1975

Semiconducting polymers for gas detection

Conjugated polyenes, and polyesters containing phthalocyanine in their backbone, were synthesized. These polymers were characterized by chemical analysis, thermogravimetric analysis, spectral analysis, and X-ray diffraction studies for crystallinity, as well as for their film-forming capability and gas/polymer interactions. Most of the polymers were relatively insensitive to water vapor up to 50 percent relative humidity, but the polyester/phthalocyanine (iron) polymer was relatively insensitive up to 100 percent RH. On the other hand, poly(p-dimethylaminophenylacetylene) was too conductive at 100 percent RH. Of the gases tested, the only ones that gave any evidence of interacting with the polymers were SO2, NOx, HCN and NH3. Poly(imidazole)/thiophene responded to each of these gases at all relative humidities, while the other polymers gave varying response, depending upon the RH. Thus, since most of these gases were electron-accepting, the electron-donating character of poly(imidazole)/thiophene substantiates the concept of electronegativity being the operating principle for interaction effects. Of the six polymers prepared, poly(imidazole)/thiophene first showed a very good response to smoldering cotton, but it later became nonresponsive; presumably due to oxidation effects.

Byrd, N. R.↗
NASA NTRS1976

Selected fretting-wear-resistant coatings for titanium - 6-percent-aluminum - 4-percent-vanadium alloy

A titanium - 6-percent-aluminum - 4-percent-vanadium alloy (Ti-6Al-4V) was subjected to fretting-wear exposures against uncoated Ti-6Al-4V as a baseline and against various coatings and surface treatments applied to Ti-6Al-4V. The coatings evaluated included plasma-sprayed tungsten carbide with 12 percent cobalt, aluminum oxide with 13 percent titanium oxide, chromium oxide, and aluminum bronze with 10 percent aromatic polyester; polymer-bonded polyimide, polyimide with graphite fluoride, polyimide with molybdenum disulfide (MoS2), and methyl phenyl silicone bonded MoS2, preoxidation surface treatment, a nitride surface treatment, and a sputtered MoS2 coating. Results of wear measurements on both the coated and uncoated surfaces after 300,000 fretting cycles indicated that the polyimide coating was the most wear resistant and caused the least wear to the uncoated mating surface.

Bill, R. C.↗
NASA NTRS1976

Environmental charging of spacecraft-tests of thermal control materials for use on the global positioning system flight space vehicle. Part 2: Specimen 6 to 9

The NASA/USAF program on the Environmental Charging of Spacecraft Surfaces consists, in part, of experimental efforts directed toward evaluating the response of materials to the environmental charged particle flux. Samples of thermal blankets of the type to be used on the Global Positioning System Flight Space Vehicles were tested to determine their response to electron flux. The primary result observed was that no discharges were obtained with the quartz-fiber-fabric-covered multilayer insulation specimen. The taped aluminized polyester grounding system used on all specimens did not appear to grossly deteriorate with time; however, the specimens require specific external pressure to maintain constant grounding system resistance.

Stevens, N. J.↗
NASA NTRS1976

Measured opening characteristics of an electromagnetically opened diaphragm for the Langley expansion tunnel

Results from an experimental study of the opening characteristics of an electromagnetically opened, 15.24 cm diameter diaphragm are presented. This diaphragm consists of a polyester film bonded to a preformed wire and is opened by passing a current pulse (capacitor discharge) through the wire. The diaphragm separates the acceleration section of the expansion tunnel from the nozzle so that the nozzle may be at a lower pressure than the acceleration section prior to a test. Opening times and cleanness of the opened area were examined for dependence on diaphragm thickness, on wire diameter, on technique of bonding the wire to the diaphragm, and on voltage and energy level of the energy source. Time histories of the pitot pressure measured at the expansion-tunnel nozzle entrance location are presented for (1) no diaphragm, (2) a flow-opened diaphragm, and (3) an electromagnetically opened diaphragm.

Moore, J. A.↗
NASA NTRS1975

Infrared emission spectra of elastohydrodynamic contacts

A small diamond disk mounted as a window in a steel plate was covered with test fluid, and a weighted steel ball was rotated over the window so as to form a sliding elastohydrodynamic (EHD) contact region. Some of the radiant energy generated in this region, both in the fluid and at the boundaries, passed through the window into an infrared interferometer, giving rise to an emission spectrum. This spectrum could be separated into contributions from the fluid and from the ball surface, making it possible, by appropriate calibrations, to estimate their temperatures separately under operating conditions. Moreover, the shape of the discrete spectral bands of the fluid permitted some inferences on its state. Two fluids were studied under identical mechanical conditions, a polyester and a naphthenic oil, each containing an equal amount of polymethylstyrene as a spectral indicator. Differences of band intensity, band width, and frequency could, therefore, be attributed to differences in the behavior of the base fluid.

Lauer, J. L.↗
NASA NTRS1977

Development of a special purpose spacecraft interior coating. Phase 2

Numerous acrylic and epoxy modifiers for the fluorocarbon latex resin base were investigated. Optimum coatings were developed by modifying the fluorocarbon latex with an epoxy acrylic resin system. In addition, a number of other formulations, containing hard acrylics as modifiers, displayed attractive properties and potential for further improvements. The preferred formulations dried to touch in about one hour and were fully dried in about twenty four hours under normal room temperature and humidity conditions. In addition to physical and mechanical properties either comparable or superior to those of commercial solvent base polyurethane or polyester coatings, the preferred compositions meet the flammability and offgassing requirements specified by NASA.

Bartoszek, E. J.↗