SEARCH · Search NASA

Results for “random microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Investigating Grain Structure and Microcracking in SiCf-SiCm Composites Using 4D-STEM

Silicon carbide (SiC) fiber-reinforced SiC matrix composites (SiCf-SiCm) are promising materials for accident-tolerant fuel (ATF) cladding in light water reactors. This paper, using four-dimensional scanning transmission electron microscopy (4D-STEM), studied the microstructure of SiCf-SiCm at nanoscale and provided grain statistics at the CVI/fiber region. Here, the results reveal that CVI region mainly contain irregular sub-micron grains (115 nm to 1800 nm) with a preferred orientation, while the fiber region has nano equiaxed grains (21 nm to 78 nm) with random orientations. Centered dark field imaging over the fiber regions verified the grain size measurement by 4D-STEM. Through 4D-STEM virtual dark field imaging and orientation mapping, intragranular propagation was identified as the fracture mechanism for a microcrack observed within the CVI region. The amorphous pyrolytic carbon layer was also shown to effectively arrest the microcrack.

4D-STEM↗

DOE OSTI2023

Domain wall motion across microstructural features in polycrystalline ferroelectric films

This paper describes the effect of microstructural features such as grain boundaries and triple points on the pinning of domain wall motion in perovskite Pb(Zr 0.52 Ti 0.48 )O 3 (PZT) films on polycrystalline SrRuO 3 /SrTiO 3 substrates. Here, spatial variability in the collective domain wall dynamics was assessed using non-linearity mapping via Band Excitation Piezoresponse Force Microscopy (BE-PFM). Collocating the non-linearity maps with triple point locations (as visualized by EBSD) allowed for exploration of the effects that local microstructure (e.g., grain boundary) have on domain wall motion. It was found that the extrinsic behavior varied with both the misorientation angle and the proximity to the grain boundary. The width of influence of individual grain boundaries on the motion of domain walls was a function of the character of the grain boundary; random grain boundaries exhibit deeper minima in α d /d 33,initial and larger widths of influence (up to 905 nm) compared to coincident site lattice (CSL) boundaries (up to 572 nm). Additionally, triple points containing larger numbers of random boundaries exhibited non-Rayleigh behavior to greater distances, suggesting that the triple point provides either a deep potential minimum or a region where domain wall motion is unfavorable.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Microstructure of irradiated AGR TRISO particle buffer layers as measured by X-ray computed tomography

Shrinkage of the initially low-density buffer layer in tristructural isotropic (TRISO) coated fuel particles during irradiation is a well-known phenomenon with potential implications for fission product and actinide transport, as well as potential pyrocarbon fracture that in some cases has been observed to impact particle performance. During post-irradiation examination, the buffer layer's structure is commonly determined using 2D microscopy of a particle cross section or a series of particle cross sections at staggered depths. Although these methods provide a general idea of the irradiated buffer microstructure, they do not provide a full picture of the TRISO coating microstructure. By contrast, x-ray computed tomography (XCT) provides full 3D imaging of the TRISO particle. Particles from various compacts irradiated for the Advanced Gas Reactor Fuel Development and Qualification Program were imaged using XCT. Some of these particles were selected because of abnormal fission product inventories (e.g., low 137 Cs), whereas others were randomly selected from the center of the fission product inventory distribution. Qualitative and quantitative analysis techniques were applied to the randomly selected particles as representatives of typical TRISO behavior to study the post-irradiation structure of the buffer layer. These results showed that, while separation of the buffer and inner pyrolytic carbon layers was a common behavior during the radiation-induced shrinkage of the buffer, a portion of the original buffer/inner pyrolytic carbon interface remained intact throughout irradiation in nearly all cases. Furthermore, these results also indicated clear trends in the degree of buffer densification with irradiation temperature and fluence.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Conjugated Polymer Controlled Morphology and Charge Transport of Small-Molecule Organic Semiconductors

In this study, we report an efective approach to tune the crystallization, microstructure and charge transport of solution-processed organic semiconductors by blending with a conjugated polymer additive poly(3-hexylthiophene) (P3HT). When 6,13-bis(triisopropylsilylethynyl) pentacene (TIPS pentacene) was used as a model semiconductor material to mix with diferent amount of P3HT, their intermolecular interactions led to distinctive TIPS pentacene flm morphologies, including randomly-oriented crystal ribbons, elongated needles with enhanced long-range order, and grasslike curved microwires with interlinkages. Each type of morphology was found to further correlate to considerably diferent charge transport and device performance. As compared to pristine TIPS pentacene devices, bottom-gate, top-contact OTFTs with 2% in weight P3HT additive showed a 2-fold and 5-fold improvement of average feld-efect mobility and performance consistency (defned as the ratio of average mobility to the standard deviation), respectively. The improvement in transistor electrical performance can be attributed to the combined efect of enhanced crystal orientation and uniformity, as well as increased areal coverage. This work can be applied beyond the particular example demonstrated in this study and to tune the charge transport of other small-molecule organic semiconductors in general.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

The Effect of Homogenization Heat Treatment on the Texture Evolution in U-10Mo Alloy

Uranium alloyed with 10 wt% Mo (U-10Mo) undergoes discontinuous precipitation (DP) when subjected to sub-eutectoid heat-treatment. It is hypothesized that the crystallographic texture of the U-10Mo can be modified to minimize the degree of DP, however the evolution of texture throughout the manufacturing process is not well understood. Crystallographic textures of two U-10Mo samples homogenized at 900°C and 1000°C were studied after uniaxial rolling and annealing. A total of 6 samples were analyzed upon rolling using a combination of hot and cold rolling conditions to strains of 83%, 90% and 97% and subsequently annealed at 700°C for one hour. Microstructures and textures were analyzed via electron backscatter diffraction (EBSD) for each homogenization, strain and post-annealed states. Results show that the U-10Mo exhibits typical rolling textures seen in body-centered cubic materials with increasing intensities of both a- and ?-fibers with increasing strain. After recrystallization, the texture appeared to be effectively randomized in all samples. Homogenization temperature showed no effect on the rolling and recrystallization behavior. Potential factors leading to the randomization of texture are discussed along with the implications of textures on the minimization of DP.

nuclear fuel, texture, rolling↗

DOE OSTI2020

Engineering the Microstructure and Morphology of Explosive Films via Control of Interfacial Energy

Physical vapor deposition of organic explosives enables growth of polycrystalline films with a unique microstructure and morphology compared to the bulk material. This study demonstrates the ability to control crystal orientation and porosity in pentaerythritol tetranitrate films by varying the interfacial energy between the substrate and the vapor-deposited explosive. Additionally, variation in density, porosity, surface roughness, and optical properties is achieved in the explosive film, with significant implications for initiation sensitivity and detonation performance of the explosive material. Various surface science techniques, including angle-resolved X-ray photoelectron spectroscopy and multiliquid contact angle analysis, are utilized to characterize interfacial characteristics between the substrate and explosive film. Optical microscopy and scanning electron microscopy of pentaerythritol tetranitrate surfaces and fracture cross sections illustrate the difference in morphology evolution and the microstructure achieved through surface energy modification. X-ray diffraction studies with the Tilt-A-Whirl three-dimensional pole figure rendering and texture analysis software suite reveal that high surface energy substrates result in a preferred (110) out-of-plane orientation of pentaerythritol tetranitrate crystallites and denser films. Low surface energy substrates create more randomly textured pentaerythritol tetranitrate and lead to nanoscale porosity and lower density films. This work furthers the scientific basis for interfacial engineering of polycrystalline organic explosive films through control of surface energy, enabling future study of dynamic and reactive detonative phenomena at the microscale. Results of this study also have potential applications to active pharmaceutical ingredients, stimuli-responsive polymer films, organic thin film transistors, and other areas.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Saturated random packing built of arbitrary polygons under random sequential adsorption protocol

Random packings and their properties are a popular and active field of research. Numerical algorithms that can efficiently generate them are useful tools in their study. This paper focuses on random packings produced according to the random sequential adsorption (RSA) protocol. Developing the idea presented by G. Zhang, where saturated random packings built of regular polygons were studied, we create an algorithm that generates strictly saturated packings built of any polygons. Then, the algorithm was used to determine the packing fractions for arbitrary triangles. In this work, the highest mean packing density, 0.552 814 ± 0.000 063, was observed for triangles of side lengths 0.63 : 1 : 1. Additionally, microstructural properties of such packings, kinetics of their growth, as well as distributions of saturated packing fractions and the number of RSA iterations needed to reach saturation were analyzed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Controlling reversible phase transitions in rare-earth nickelates for novel memory devices

Resistive switching in correlated complex oxides is lucrative for emerging applications in neuromorphic computing, and densely scaled non-volatile memory. Electrical conductance of such complex oxides can be controllable switched across multiple orders of magnitude by either (a) electroforming a conduction channel (e.g., in tungsten oxide), or (b) inducing Mott-Hubbard transition (e.g., in rare-earth nickelates)– both via controlled migration of defects (such as oxygen vacancies) under applied bias. Nevertheless, the promise of such defect-driven electronic transitions are far from realized due to a lack of fundamental understanding of the atomic-scale processes that underlie migration and spatiotemporal evolution of oxygen vacancies over nano-to-mesoscopic length/timescales under applied electric field. In this project, we employ a synergistic integration of density functional theory (DFT) calculations, ab initio/classical molecular dynamics (AIMD/CMD) simulations, machine learning (ML), precision synthesis, and multi-modal X-ray imaging experiments to address this knowledge gap. Such an integrated approach offers to elucidate the correlations between subtle structural distortion and oxidation states; treat localized charge carriers; describe defect/ion transport in the presence of electric field; and, in turn, greatly advance the current understanding of microstructural evolution in complex oxides under applied bias. The fundamental knowledge gained from this work will enable precise control over hierarchical defect structures and unravel new routes to manipulate resistance states in complex oxides. This, in turn, will accelerate design of novel devices with desired set of neural functionalities, and high-speed densely-scaled resistive random access memory technologies.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Microstructure and crystallographic texture of high frequency electric resistance welded X65 pipeline steel

Here, microstructure and crystallographic texture and their correlation with impact toughness of high-frequency electric resistance welded (HF-ERW) X65 Grade pipeline steel have been investigated. X65 base metal after HF-ERW has formed a typical hourglass-shaped weld joint with four different regions, including the thermomechanical-affected zone (TMAZ), fine-grained heat affected zone (FGHAZ), coarse-grained heat affected zone (CGHAZ), and bondline (Weld Zone). X65 base metal shows prominent (113) [110] and (112) [110] texture components due to thermomechanical-controlled processing. TMAZ depicted random texture with a minor intensity of Cube component (001)[110] due to the partial recrystallization during welding. In the FGHAZ and CGHAZ, near the bondline, the base metal texture has been converted to rotated Goss (110) [110], Goss (110) [001], and rotated cube (001) [110] due to the recrystallization of the austenite and the shear deformation in the austenite temperature range. A high density of {100} and {110} cleavage planes is observed in the CGHAZ, which is often found to be the fracture location for the impact toughness testing.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Microstructure, Texture, and Strength Development during High-Pressure Torsion of CrMnFeCoNi High-Entropy Alloy

The equiatomic face-centered cubic high-entropy alloy CrMnFeCoNi was severely deformed at room and liquid nitrogen temperature by high-pressure torsion up to shear strains of about 170. Its microstructure was analyzed by X-ray line profile analysis and transmission electron microscopy and its texture by X-ray microdiffraction. Microhardness measurements, after severe plastic deformation, were done at room temperature. It is shown that at a shear strain of about 20, a steady state grain size of 24 nm, and a dislocation density of the order of 1016 m−2 is reached. The dislocations are mainly screw-type with low dipole character. Mechanical twinning at room temperature is replaced by a martensitic phase transformation at 77 K. The texture developed at room temperature is typical for sheared face-centered cubic nanocrystalline metals, but it is extremely weak and becomes almost random after high-pressure torsion at 77 K. The strength of the nanocrystalline material produced by high-pressure torsion at 77 K is lower than that produced at room temperature. The results are discussed in terms of different mechanisms of deformation, including dislocation generation and propagation, twinning, grain boundary sliding, and phase transformation.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Effects of Changing Hot Rolling Direction on Microstructure, Texture and Mechanical Properties of Cu-2.7Be Sheets

A hot rolling scheme (cross-rolling and unidirectional rolling) was adopted to process Cu-2.7Be sheets used as multiplier dynodes in photomultiplier. The effects of changing rolling direction on microstructure, texture and mechanical properties were studied by a combination of XRD, EBSD and TEM. It was found that higher copper-type texture and lower brass texture intensity were obtained in the ultimately cross-rolling (CR) sheet compared with the unidirectional rolling (UR) sheet.The EBSD results indicated that the grain orientation from mainly 〈101〉 for UR sample turns to random for CR sample. Great enhancements in YS and UTS after unidirectional rolling were attributed to the massive and polygonal γ precipitates. The CR sample exhibited lower anisotropy, because of the increase of S and γ precipitates with spherical and tiny shape.

36 MATERIALS SCIENCE↗

NASA NTRS1985

Impact wear of iron rich superalloys

The impact-sliding wear resistance of chill cast and aligned eutectic Fe-base superalloys against M42 and 17-4 PH steel counterface materials is examined. The aligned material tests were run with carbide fibers perpendicular to the counterface contact surface and the characterization focused on fracture processes as observed in the subsurface microstructure of the worn materials. Metallographic analyses were performed on specimens exposed to various numbers of repetitive impact load cycles, and for comparison, two other aligned composites were tested with the same fiber orientation under identical test conditions against hardened M42 tool steel. A strong improvement was found in wear resistance of an aligned eutectic structure as compared to the corresponding randomized chill cast structure. Experiments with the softer 17-4 counterface were characterized by transfer onto the Fe-base superalloy, and the cracks formed were oriented transverse to the relative sliding direction and occurred in a periodic fashion. Observations in subsurface regions of the worn materials indicated crack intergranularity with an occasional transgranular fracture of the M7C3 carbide phase.

Wayne, S. F.↗

DOE OSTI2020

Modeling the role of local crystallographic correlations in microstructures of Ti-6Al-4V using a correlated structure visco-plastic self-consistent polycrystal plasticity formulation

This paper presents a multi-level crystal plasticity-based simulation framework for modeling mechanical response and microstructure evolution of Ti-6Al-4V with α-lath/lamellar microstructures. Here, the model is a correlated structure visco-plastic self-consistent (CS-VPSC) formulation linking three scales: a single crystals micro-scale, a lath/lamellar colony meso-scale, and a lath/lamellar aggregate macro-scale. A selected hardening law for the evolution of critical resolved shear stress per slip system used in CS-VPSC is phenomenological. However, it adjusts the resistances of basal and prismatic slip systems based on the geometry of slip transfer between adjacent lamellae. Consistent with experimental evidences, the resolved shear stress on the pyramidal slip planes is dependent not only on the stress in the direction of slip but also on the two orthogonal shear stress components and the three normal stress components (non-Schmid effects). Electron backscatter diffraction (EBSD) data in conjunction with a procedure relying on α→β phase transformation is used to construct paired variants of α-laths/lamellae satisfying their local crystallographic correlations. The procedure fits volume fractions of individual laths/lamellae with the experimental EBSD data and selects a distribution of habit planes between adjacent variants with respect to the loading direction. The simulation framework is applied to interpret the deformation behavior in tension and compression along two sample directions of Ti-6Al-4V fabricated via laser powder bed fusion. Moreover, the model is used to simulate texture evolution during rolling of the material to large strains. It is demonstrated that the model is capable of predicting plastic anisotropy/asymmetry and the concomitant texture evolution. While the model reveals a significant effect of habit plane inclination with respect to the loading direction on yield stress, the comparison of the data and model predictions shows that a random distribution of habit planes fits the flow response. It is further inferred that the tension-compression asymmetry arises from the non-Schmid effects.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Microstructural Evolution of Tantalum During Deformation and Subsequent Annealing

Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.

36 MATERIALS SCIENCE↗

NASA NTRS2014

Effects of Dopant on Depoling Temperature in Modified BiScO3 - PbTiO3

In recent years there has been a renewed interest for high temperature piezoelectrics for both terrestrial and aerospace applications. These applications are limited in part by the operating temperature, which is usually taken as one half of the Curie temperature (Tc), and is 200C for one of the most widely used commercial piezoelectrics, Pb(Zr,Ti)O3 (PZT). In an effort to increase Tc, subsequent research into high temperature Bi(BB)O3 PbTiO3 piezoelectrics led to the discovery of the morphotropic phase boundary (MPB) in the high-Tc BiScO3 PbTiO3 (BS-PT) system with a Tc of 460C and a d33 of 460 pmV. The Tc marks the ferroelectric to paraelectric phase transformation and while, in general, a phase transformation leads to thermal depoling in piezoelectrics with low or moderate Tcs, for high Tc piezoelectrics thermally assisted dipole rotation can lead to randomization of domains at temperatures below Tc. It becomes necessary to determine the depoling temperature (Td) which dictates the actual working temperature range. By doping for Sc and Ti the Td can be shifted while maintaining similar electromechanical properties as a function of temperature. The effect of this B-site doping on depoling temperature has been explored through the characterization of microstructure and weakhigh field measurements.

Actuator↗

DOE OSTI2023

Ultrafine-grained Fe-TiB 2 high-modulus nanocomposite steel with high strength and isotropic mechanical properties by laser powder bed fusion

Fe-TiB 2 metal matrix composite, also called high-modulus steels (HMSs), are of great interest for applications in fuel-efficient transportation infrastructure, aerospace, and wear industries due to their high specific stiffness and yield strength. However, conventional cast Fe-TiB 2 HMSs often contain coarse and sharp-edged TiB 2 particles which easily trigger premature cracking during loading. Here, we synthesized a Fe-TiB 2 nanocomposite HMS via laser powder bed fusion (LPBF) additive manufacturing of mixed micro-sized powders of Fe, Ti, and Fe 2 B. We investigated the microstructure formation and mechanical behavior of the Fe-TiB 2 HMS. We found that in situ chemical reaction of Ti and Fe 2 B enables the formation of TiB 2 particles at nanoscale during rapid solidification of LPBF. These nanoscale TiB 2 particles can serve as heterogeneous nucleation sites and promote the formation of ultrafine and equiaxed α-Fe grains with random crystallographic textures, which differ from many other additively manufactured (AM) metal alloys characteristic of strong crystallographic textures. As such, isotropic mechanical properties were achieved in the AM Fe-TiB 2 nanocomposite HMS with a high elastic modulus of ~ 240 GPa, an exceptional yield strength of ~ 1450 MPa, and a large plasticity of ~ 20% under compression. Quantitative analysis reveals that the high yield strength primarily originates from strengthening contributions of the ultrafine grains with an average grain size of ~450 nm, the nanoscale TiB 2 reinforcing particles of 20–180 nm, and a high density of printing-induced dislocations of the order of 10 15 m –2 . In situ synchrotron high-energy X-ray diffraction unveils the load partitioning from the softer α-Fe matrix to the stiffer and stronger TiB 2 nanoparticles, contributing to the sustained strain hardening during compression. Our work not only provides a general pathway for achieving high-performance metal matrix nanocomposites by in situ chemical reaction and precipitation of ceramic nanoparticles during additive manufacturing, but also offers mechanistic insights into the deformation mechanism of nanoparticle-reinforced HMS composites.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Effect of transport mechanism on the coarsening of bicontinuous structures: A comparison between bulk and surface diffusion

Here, coarsening of bicontinuous microstructures is observed in a variety of systems, such as nanoporous metals and mixtures that have undergone spinodal decomposition. To better understand the morphological evolution of these structures during coarsening, we compare the morphologies resulting from two different coarsening mechanisms, surface and bulk diffusion. We perform phase-field simulations of coarsening via each mechanism in a two-phase mixture at nominal volume fractions of 50%-50% and 36%-64%, and the simulated structures are characterized in terms of topology (genus density), the interfacial shape distribution, structure factor, and autocorrelations of phase and mean curvature. We observe self-similar evolution of morphology and topology and agreement with the expected power laws for dynamic scaling, in which the characteristic length scale increases over time proportionally to t 1/4 for surface diffusion and t 1/3 for bulk diffusion. While we observe the expected difference in the coarsening kinetics, we find that differences in self-similar morphology due to coarsening mechanism are relatively small, although typically they are larger at 36% volume fraction than at 50% volume fraction. In particular, we find that bicontinuous structures coarsened via surface diffusion have lower scaled genus densities than structures coarsened via bulk diffusion. We also compare the self-similar morphologies to those in literature and to two model bicontinuous structures, namely, constant-mean-curvature surfaces based on the Schoen G minimal surface and random leveled-wave structures. The average scaled mean curvatures of these model structures agree reasonably with those of the coarsened structures at both 36% and 50%, but we find substantial disagreements in the scaled genus densities and the standard deviations of mean curvature.

36 MATERIALS SCIENCE↗

NASA NTRS2002

Higher-Order Theory: Structural/MicroAnalysis Code (HOTSMAC) Developed

The full utilization of advanced materials (be they composite or functionally graded materials) in lightweight aerospace components requires the availability of accurate analysis, design, and life-prediction tools that enable the assessment of component and material performance and reliability. Recently, a new commercially available software product called HOTSMAC (Higher-Order Theory--Structural/MicroAnalysis Code) was jointly developed by Collier Research Corporation, Engineered Materials Concepts LLC, and the NASA Glenn Research Center under funding provided by Glenn's Commercial Technology Office. The analytical framework for HOTSMAC is based on almost a decade of research into the coupled micromacrostructural analysis of heterogeneous materials. Consequently, HOTSMAC offers a comprehensive approach for analyzing/designing the response of components with various microstructural details, including certain advantages not always available in standard displacement-based finite element analysis techniques. The capabilities of HOTSMAC include combined thermal and mechanical analysis, time-independent and time-dependent material behavior, and internal boundary cells (e.g., those that can be used to represent internal cooling passages, see the preceding figure) to name a few. In HOTSMAC problems, materials can be randomly distributed and/or functionally graded (as shown in the figure, wherein the inclusions are distributed linearly), or broken down by strata, such as in the case of thermal barrier coatings or composite laminates.

Arnold, Steven M.↗