Search NASA⌕ Search

SEARCH · Search NASA

Results for “recombination layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Hole transport layer selection for stable and efficient carbon electrode-based perovskite solar cells

Perovskite solar cell (PSC) technology has achieved remarkable progress, with champion power conversion efficiencies (PCE) exceeding 26%. However, the long-term stability of PSCs remains a significant barrier to their widespread commercialization. Carbon-based PSCs (C-PSCs) have gained attention as a promising cost-effective and scalable production solution, replacing expensive metal electrodes and offering improved stability. Despite these advantages, C-PSCs face challenges in matching the performance of noble metal-based PSCs, particularly in terms of carrier extraction efficiency and reduced carrier recombination at the carbon/perovskite interface. The selection of hole transport materials (HTMs) is crucial for optimizing this interface, but comprehensive studies on HTM selection for C-PSCs are limited. This study systematically investigated three commonly used hole transport layers (HTLs): Spiro-OMeTAD, CuSCN, and PTAA. Our results show that Spiro-OMeTAD-based C-PSCs exhibit the best overall performance, achieving a PCE of 19.29%. CuSCN-based devices, while lower in efficiency (11.94% PCE), demonstrated superior stability, retaining approximately 60% of their initial performance after 500 hours under ambient conditions. PTAA-based devices achieved a PCE of 12.92% but exhibited significant degradation, maintaining only ∼35% of their original efficiency over the same duration. These findings highlight the importance of selecting HTLs that balance performance and stability and emphasize the need for further optimization to enhance the commercial viability of C-PSCs.

14 SOLAR ENERGY↗
DOE OSTI2020

Effect of Surface Texture on Pinhole Formation in SiO x -Based Passivated Contacts for High-Performance Silicon Solar Cells

High-efficiency silicon solar cells rely on some form of passivating contact structure to reduce recombination losses at the crystalline silicon surface and losses at the metal/Si contact interface. One such structure is polycrystalline silicon (poly-Si) on oxide, where heavily doped poly-Si is deposited on a SiO x layer grown directly on the crystalline silicon (c-Si) wafer. Depending on the thickness of the SiO x layer, the charge carriers can cross this layer by tunneling (<2 nm SiO x thickness) or by direct conduction through disruptions in the SiOx, often referred to as pinholes, in thicker SiO x layers (>2 nm). In this work, we study structures with tunneling- or pinhole-like SiO x contacts grown on pyramidally textured c-Si wafers and expose variations in the SiOx layer properties related to surface morphology using electron-beam-induced current (EBIC) imaging. Using EBIC, we identify and mark regions with potential pinholes in the SiO x layer. We further perform high-resolution transmission electron microscopy on the same areas, thus allowing us to directly correlate locally enhanced carrier collection with variations in the structure of the SiO x layer. Our results show that the pinholes in the SiO x layer preferentially form in different locations based on the annealing conditions used to form the device. With greater understanding of these processes and by controlling the surface texture geometry, there is potential to control the size and spatial distribution of oxide disruptions in silicon solar cells with poly-Si on oxide-type contacts; usually, this is a random phenomenon on polished or planar surfaces. Such control will enable us to consistently produce high-efficiency devices with low recombination currents and low junction resistances using this contact structure.

14 SOLAR ENERGY↗
DOE OSTI2026

Solutions to Droop and the Green Gap by Novel Carrier Injection

Long-wavelength (green, yellow, red) visible light-emitting diodes (LEDs) have historically been inefficient compared to blue light-emitters in the III-nitrides. This is due to many factors, including poor material quality due to the low growth temperatures required for high Incomposition InGaN quantum wells (QWs), and the polar nature of the III-nitride crystal structure. Spontaneous and piezoelectric polarization in the III-nitrides causes enhanced quantum-confined Stark effect (QCSE), which spatially separates electrons and holes and reduces radiative recombination (ie: light output) from the devices. Polarization in the crystal also induces additional potential barriers that electrons and holes must cross over before entering the QWs where they can recombine to emit light. Both of these polarization effects worsen as emission wavelength increases, making blue III-nitride LEDs are the most efficient and red III-nitride LEDs the least efficient. The focus of this project has been solving the latter polarization-related issue through the implementation of V-defects in long wavelength LEDs. V-defects are morphological defects which are commonly observed in c-plane III-nitrides. They are observed as hexagonal pyramid-shaped depressions on the c-plane surface, with six semipolar sidewalls. They typically form at the apex of threading dislocations (TDs) under conditions of kinetically-limited growth and low growth-temperature. They were initially thought to be detrimental to LED performance and much early work focused on eliminating them entirely from III-nitride devices. However, over the past decade work has emerged that indicate that they can improve LED performance by allowing electrons and holes to bypass the polarization-induced barriers present in the c-plane and directly enter the QWs of an LED. This is due to the semipolar nature of the V-defect sidewall: these sidewalls are thin and lack the polarization-induced barriers which prevent carriers easily moving between layers. V-defects have since been determined to be an efficient avenue by which to inject electrons and holes into the c-plane QWs where they can recombine to emit light. Throughout this project we have explored lateral injection through a variety of methods: simulation (Task 2), epitaxial growth of V-defect and non-V-defect LEDs (Tasks 1, 3, 4, 5, 6), and advanced characterization methods (Task 7). All tasks have been completed. A description of each task completed follows from this section.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Characterizing W sources in the all-W wall, all-RF WEST tokamak environment

In this work, experimental data, together with interpretive modeling tools, are examined to study trends in the tungsten (W) source in the all-W environment of the WEST tokamak, both from the divertor and from the main chamber. In particular, a poloidal limiter protecting an ion cyclotron resonance heating (ICRH) antenna is used as proxy for main chamber sourcing. The key study is carried out by stepping up lower hybrid current drive (LHCD) power, as the only auxiliary power source. Limiter and divertor W sources exhibit a qualitatively similar proportionality to the total power crossing the separatrix, P SEP , although the main chamber source remains substantially lower than the divertor source, for the range of P SEP accessible in the experiments. Intepretive modeling of the limiter source is carried out with a particle-in-cell (PIC) sheath model coupled to a surface sputtering model. Oxygen is used as a proxy for all light impurity species allowing for characterization of the critical W erosion regions. To get a good quantitative match to the data, it is necessary to assume that the oxygen arrives at the surface mostly at high ionization stages (4+ and above). A separate simulation with SOLEDGE-EIRENE, constrained to measured upstream scrape-off-layer plasma profiles, gives oxygen fractional abundances that are compatible with the PIC simulation result. This is understood to arise from transport processes that dominate over recombination. Substituting the LHCD by ICRH, in an equivalent experiment, the local W source exhibits a 3× enhancement. This can be matched by the simulation, by assuming local RF electric field rectification, based on ~100 eV peak-to-peak, near-antennna electric field. This work has highlighted the particular importance of understanding the ion charge state balance of light impurities as these are most likely the dominant sputtering species in fusion devices with high-Z walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Nanopinhole-Enabled, Hole-Selective Poly-Si/SioxNy Passivating Contacts on Textured c-Si for Si Solar Cells

The next-generation silicon photovoltaics will be based on passivating electron- and hole-selective contacts with both very low interface recombination and contact resistivities. While the emerging mainstream TOPCon technology has developed excellent electron-selective poly-Si/tunneling SiOx contacts, hole-selective contacts, especially on textured surfaces, have remained a significant challenge. This contribution introduces novel high-performance hole selective poly-Si contacts on pyramid-textured Si, enabled by electrochemically produced hole transport nanopinholes in a 10 nm oxynitride passivating dielectric stack capped by p+ poly-Si. The highly passivating oxynitride layer is produced via atomic intermixing of O and N atoms in the initial SiOx/SiNy layer stack upon thermal annealing. Carrier transport is governed by nanopinhole density and size are tuned by Ag nanoparticle electrodeposition and surface attachment chemistries. This results in passivating hole contact resistivities in the m..omega..-cm2 range, while preserving interface recombination current prefactor around 5 fA/cm2.

14 SOLAR ENERGY↗
DOE OSTI2020

Thermally Activated Delayed Fluorescence Sensitization for Highly Efficient Blue Fluorescent Emitters

Hyperfluorescence is emerging as a powerful strategy to develop optoelectronic devices with high-color purity and enhanced stability. It requires appropriate integration of a sensitizer displaying efficient thermally activated delayed fluorescence (TADF) and an emitter displaying strong, narrow-band fluorescence. Here, through a joint computational and experimental approach, we provide an unprecedented, end-to-end systems level description of the electronic and optical processes that take place in a hyperfluorescent emissive layer composed of a TADF sensitizer, bis(2,5-di(9H-carbazol-9-yl)phenyl)-1,3,4-oxadiazole (4CzDPO), and a fluorescent emitter, 2,5,8,11-tetra-tert-butylperylene (TBPe). We combine the photophysical properties measurement of the emissive layer with the computational determination of the electronic properties, film morphology, and excitation transfer phenomena. The Förster resonance energy transfer rates from 4CzDPO to TBPe are on the order of 1011 s–1, considerably higher than the radiative and non-radiative recombination rates for 4CzDPO. These features ensure nearly complete energy transfer to TBPe, leading to a five-fold increase in the photoluminescence quantum yields in the 4CzDPO:TBPe system in comparison to neat films of 4CzDPO. Furthermore, our approach highlights the factors that can provide efficient energy transfer from TADF molecules to fluorescent emitters, suppress energy transfer among TADF molecules, and avoid the need for a host material within the emissive layer.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Near- and far scrape-off layer transport studies in detached, small-ELM ASDEX Upgrade discharges by means of EMC3-EIRENE

We compare various diagnostics characterizing an ASDEX Upgrade upper single-null discharge to EMC3-EIRENE simulations now including volumetric recombination and main chamber plasma-wall interaction but not yet drifts. The discharge is in a small-ELM regime and is approaching detachment due to a density ramp and nitrogen seeding. Time/ELM averaged upstream density, electron and ion temperature measurements as well as downstream ion saturation current, electron temperature and power flux measurements match the simulation within the error bars before and after reaching detachment, qualifying the code for this regime. Although the Ion Cyclotron Resonance Heating (ICRH) antenna limiters are 35 mm away from the separatrix, i.e. ten times the typical near-SOL power fall-off length $\lambda^{near}_q\ =\ $3.8 mm, they receive power fluxes of several hundreds of kW exceeding the ones to the outer target in the detached phase and strongly contribute to the particle fueling. This is explained by a substantially larger far-SOL power fall-off length $\lambda^{far}_q\ =\ $25 mm possibly caused by the small ELMs in the detached phase and the occurrence of a density shoulder.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Embedding physics domain knowledge into a Bayesian network enables layer-by-layer process innovation for photovoltaics

Process optimization of photovoltaic devices is a time-intensive, trial-and-error endeavor, which lacks full transparency of the underlying physics and relies on user-imposed constraints that may or may not lead to a global optimum. Herein, we demonstrate that embedding physics domain knowledge into a Bayesian network enables an optimization approach for gallium arsenide (GaAs) solar cells that identifies the root cause(s) of underperformance with layer-by-layer resolution and reveals alternative optimal process windows beyond traditional black-box optimization. Our Bayesian network approach links a key GaAs process variable (growth temperature) to material descriptors (bulk and interface properties, e.g., bulk lifetime, doping, and surface recombination) and device performance parameters (e.g., cell efficiency). For this purpose, we combine a Bayesian inference framework with a neural network surrogate device-physics model that is 100× faster than numerical solvers. With the trained surrogate model and only a small number of experimental samples, our approach reduces significantly the time-consuming intervention and characterization required by the experimentalist. As a demonstration of our method, in only five metal organic chemical vapor depositions, we identify a superior growth temperature profile for the window, bulk, and back surface field layer of a GaAs solar cell, without any secondary measurements, and demonstrate a 6.5% relative AM1.5G efficiency improvement above traditional grid search methods.

14 SOLAR ENERGY↗
DOE OSTI2022

Efficient monolithic all-perovskite tandem solar modules with small cell-to-module derate

All-perovskite tandem solar modules are promising to reduce the cost of photovoltaic systems with their high efficiency and solution fabrication, but their sensitivity to air still imposes a great challenge. Here a hot gas-assisted blading method is developed to accelerate the perovskite solidification, forming compact and thick narrow bandgap (NBG) perovskite films. Adding a reduction agent into NBG films followed by a short period of air exposure and a post-fabrication storage surprisingly increases carrier recombination lifetime and enables laser scribing in ambient conditions without obvious loss of device performance. This combination suppresses tin and iodide oxidation and forms a thin SnO 2 layer on the NBG film surface. Monolithic all-perovskite tandem solar modules showed a champion efficiency of 21.6% with a 14.3 cm 2 aperture area, corresponding to an active area efficiency of 23.0%. Lastly, the very small cell-to-module derate of 6.5% demonstrates the advantage of a tandem monolithic structure for solar modules.

14 SOLAR ENERGY↗
DOE OSTI2021

Measurement of the ionization response of amorphous selenium with 122 keV γ rays

In this work, we performed a measurement of the ionization response of 200 μm-thick amorphous selenium (aSe) layers under drift electric fields of up to 50 V/μm. The aSe target was exposed to ionizing radiation from a 57 Co radioactive source and the ionization pulses were recorded with high resolution. Using the spectral line from the photoabsorption of 122 keV γ rays, we measured the charge yield in aSe and the line width as a function of drift electric field. From a detailed microphysics simulation of charge generation and recombination in aSe, we conclude that the strong dependence of recombination on the ionization track density provides the dominant contribution to the energy resolution in aSe. These results provide valuable input to estimate the sensitivity of a proposed next-generation search for the neutrinoless ββ decay of 82 Se that aims to employ imaging sensors with an active layer of aSe. We estimate the RMS line width of the integrated ionization signal from neutrinoless ββ decay events (of deposited energy 3 MeV) to be 2.0% for a drift field of 50 V/μm. The energy resolution can be improved to 1% by correcting for the charge yield as a function of ionization density along the imaged electron tracks.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

The role of temperature on defect diffusion and nanoscale patterning in graphene

Graphene is of great scientific interest due to a variety of unique properties such as ballistic transport, spin selectivity, the quantum hall effect, and other quantum properties. Nanopatterning and atomic scale modifications of graphene are expected to enable further control over its intrinsic properties, providing ways to tune the electronic properties through geometric and strain effects, introduce edge states and other local or extended topological defects, and sculpt circuit paths. The focused beam of a scanning transmission electron microscope (STEM) can be used to remove atoms, enabling milling, doping, and deposition. Utilization of a STEM as an atomic scale fabrication platform is increasing; however, a detailed understanding of beam-induced processes and the subsequent cascade of aftereffects is lacking. Here, we examine the electron beam effects on atomically clean graphene at a variety of temperatures ranging from 400 to 1000 °C. We find that temperature plays a significant role in the milling rate and moderates competing processes of carbon adatom coalescence, graphene healing, and the diffusion (and recombination) of defects. The results of this work can be applied to a wider range of 2D materials and introduce better understanding of defect evolution in graphite and other bulk layered materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Room temperature slot-die coated perovskite layer modified with sulfonyl-γ-AApeptide for high performance perovskite solar devices

Perovskite solar cells (PSCs) exhibited remarkable progress for small aperture area cells, however, the performance of its counterpart, large aperture area cells, lags due to non-uniform and defective perovskite layers. Here, we fabricate reproducible large area homogeneous perovskite films at room temperature and without controlling humidity (up to 40 % RH) with a slot die coater on a c-TiO 2 layer deposited using a large area chemical bath. A new artificial peptide – sulfonyl-γ-AApeptide (F-GLU-S) was employed to modify the slot-die coated perovskite surface, grain boundaries and electronic defects. The multi-functional F-GLU-S with carbonyl, carboxyl, sulfonyl, benzene, and chloro groups was capable of strongly interacting with the perovskite layer and repairing the uncoordinated Pb 2+ ions and halide vacancies. As a result, both the electron and hole densities of defects were significantly suppressed; consequently, the non-radiative recombination was effectively suppressed for the modified device which can be explicitly seen in the device performance where both V oc and FF of the modified device improved considerably. Therefore, F-GLU-S modified slot-die coated MAPbI 3 – based devices demonstrated outstanding performance of 21.44 % PCE with a V oc of 1.13 V, J sc of 24.64 cm –2 , and FF 76.99 %. Furthermore, F-GLU-S passivation impeded the infiltration of moisture and oxygen due to its hydrophobic nature and defect repair potential. As a result, the modified device retained above 92 % of its original PCE after 720 h in air (room temperature and 40–60 % RH).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Perspectives on Dye Sensitization of Nanocrystalline Mesoporous Thin Films

Recent advances in our mechanistic understanding of dye-sensitized electron transfer reactions occurring at metal oxide interfaces are described. These advances were enabled by the advent of mesoporous thin films, comprised of anatase TiO 2 nanocrystallites, that are amenable to spectroscopic and electrochemical characterization in unprecedented molecular-level detail. The metal-to-ligand charge transfer (MLCT) excited states of Ru polypyridyl compounds serve as the dye sensitizers. Excited-state injection often occurs on ultrafast time scales with yields that can be tuned from unity to near zero through modification of the sensitizer or the electrolyte composition. Transport of the injected electron and the oxidized sensitizer (hole hopping) are both operative in the composite mechanism for charge recombination between the injected electron and the oxidized sensitizer. Sensitizers that contain a pendant electron donor, as well as core/shell SnO 2 /TiO 2 nanostructures, often prolong the lifetime of the injected electron and provide fundamental insights into adiabatic and nonadiabatic electron transfer mechanisms. Regeneration of the oxidized sensitizer by iodide is enhanced through halogen bonding, orbital pathways, and ion pairing. A substantial ~10 MV cm –1 electric field is created by electron injection into TiO 2 nanocrystallites that induces ion migration, reports on the sensitizer dipole orientation, and (in some cases) reorients or flips the sensitizer. Dye-sensitized conductive oxides also promote long-lived charge separation with bias dependent kinetics that provide insights into the reorganization energies associated with electron and proton-coupled electron transfer in the electric double layer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Optical analysis of III-nitride micro-light-emitting diodes with different sidewall treatments at low current density operation

Here, in this work, the optical efficiency of III-nitride blue micro-LEDs (μLEDs) ranged from 5 × 5 to 60 × 60 μm 2 with different sidewall treatments at low current density range was investigated. The results showed dielectric sidewall passivation using atomic layer deposition (ALD) has superior optical enhancement compared to conventional RF sputtering, where most of the enhancement occurred at low current density range. Additionally, the use of ALD sidewall passivation and chemical treatment offered significant efficiency improvement for different sizes of μLEDs at operating less than 1 A cm −2 and the devices without sidewall treatments did not emit light. The effect of sidewall treatments to the effective Shockley–Read–Hall (SRH) nonradiative recombination coefficient, or the effective A coefficient from the ABC model, was estimated. The effective SRH nonradiative recombination coefficient was suppressed by two orders of magnitude for devices with sidewall treatments compared to devices without sidewall passivation.

Wong, Matthew S.↗
DOE OSTI2026

Aliovalent gallium dopants remove Ti 3+ defects and improve photocatalytic and photoelectrochemical water oxidation properties of LaTiO 2 N

LaTiO 2 N is a promising semiconductor for the water splitting reaction due to its 2.1 eV band gap and stability against corrosion. However, its solar energy conversion is limited by Ti 3+ recombination defects introduced during ammonolysis. Here we show for the first time that Ti 3+ defects in LaTiO 2 N can be suppressed with incorporation of 2, 5, and 10% aliovalent gallium (Ga 3+ ) dopants during synthesis via the layered La 2 Ti 2 O 7 intermediate. Electron paramagnetic resonance (EPR) spectroscopy on the solid powders confirms a reduction in the Ti 3+ donor density from 2.97 × 10 17 cm −3 for the non-doped material to ∼6.24 × 10 16 cm −3 for 5% Ga-doped LaTiO 2 N. The remaining Ti 3+ defects are concentrated near the LaTiO 2 N surface, according to X-ray photoelectron spectroscopy. The defect reduction shifts the optical absorption edge from 2.02 to 2.09 eV and eliminates a broad absorption band at 1050 nm from the optical absorption spectra. It also removes a 1.0–1.7 eV sub-band gap photovoltage signal from surface photovoltage spectra. This suggests that empty Ti 3+ d-orbitals are located 1.0–1.7 eV above the LaTiO 2 N valence band edge. Removing these recombination states with increasing Ga 3+ content enhances the photoconversion efficiency of LaTiO 2 N during water oxidation. The optimized 2 wt% CoO x -loaded 5% Ga-doped LaTi O2 N material has a 16% AQE (400 nm) for O 2 production from aqueous silver nitrate solution and a ∼2.1 mA cm −2 water oxidation photocurrent at 1.23 V under 100 mW cm −2 Xe arc lamp illumination. The water oxidation photocurrent is stable during a 50 min test, and the Faraday efficiency for O 2 generation is 97%, confirming short-term corrosion stability of LaTiO 2 N. Altogether, these results provide a better understanding of the distribution, concentration, and impact of Ti 3+ defects on the optical, photovoltage, and photoelectrochemical properties of LaTiO 2 N. In combination with other defect control strategies, aliovalent Ga 3+ doping can help bring the solar energy conversion efficiency of LaTiO 2 N closer to the theoretical limit.

Wang, Li [University of California, Davis, CA (Uni↗
DOE OSTI2020

Semi-transparent p-type barium copper sulfide as a back contact interface layer for cadmium telluride solar cells

Optically transparent p-type materials play a critical role in transparent electronics including photovoltaic (PV) devices. P-type sulfide materials offer an alternative to oxides for PV application due to improved hole transport properties. Here, we report the solution-based synthesis of earth-abundant p-type transparent conducting barium copper sulfide (α-BaCu 4 S 3 , BCS) thin films. These films were characterized using scanning electron microscopy, X-ray diffraction, UV–Vis–NIR spectrophotometry, Raman spectroscopy, and spectroscopic ellipsometry. BCS films of ~100 nm thickness transmit >70% of visible light. We report on tests of the hole transport properties of these BCS films for cadmium telluride (CdTe) photovoltaics, finding that the BCS deposition process forms a beneficial tellurium (Te) rich surface on CdTe by selectively removing Cd from the surface. Based on our study, the BCS interface layer plays dual functions for CdTe PV devices as a hole transport material and as an etchant, enhancing the resulting device performance. We observed a significant increase in open-circuit voltage of CdTe solar cells with the BCS buffer layer. Furthermore, we discuss semitransparent CdTe solar cells with BCS as a hole transport layer and indium tin oxide as a finishing electrode. Semitransparent CdTe solar cells shows 13.3% conversion efficiency for the front side illumination and 1.2% efficiency for back side illumination, indicating high recombination of charge carriers generated close to the rear CdTe/BCS/ITO contact.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Chemically tuned intermediate band states in atomically thin Cu x GeSe/SnS quantum material for photovoltaic applications

A new generation of quantum material derived from intercalating zerovalent atoms such as Cu into the intrinsic van der Waals gap at the interface of atomically thin two-dimensional GeSe/SnS heterostructure is designed, and their optoelectronic features are explored for next-generation photovoltaic applications. Advanced ab initio modeling reveals that many-body effects induce intermediate band (IB) states, with subband gaps (~0.78 and 1.26 electron volts) ideal for next-generation solar devices, which promise efficiency greater than the Shockley-Queisser limit of ~32%. The charge carriers across the heterojunction are both energetically and spontaneously spatially confined, reducing nonradiative recombination and boosting quantum efficiency. Using this IB material in a solar cell prototype enhances absorption and carrier generation in the near-infrared to visible light range. Tuning the active layer’s thickness increases optical activity at wavelengths greater than 600 nm, achieving ~190% external quantum efficiency over a broad solar wavelength range, underscoring its potential in advanced photovoltaic technology.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Layer-by-Layer-Processed Organic Solar Cells with 18.02% Efficiency Enabled by Regulating the Aggregation of Bottom Polymers

The fabrication of organic solar cells (OSCs) by a layer-by-layer (LBL) method has attracted growing attention in recent years. As already known, the pre-aggregates of conjugated polymers in solution have a profound impact on their microstructure morphology in films. Herein, by simply controlling the solution temperature and annealing processes, the pre-aggregation behavior of D18 polymer in solution can be fine-tuned and the microstructure of D18 bottom layer is well manipulated. The optimized D18 bottom layer can effectively regulate L8-BO upper-layer-forming suitable networks for efficient charge transportation. In addition, a vertical phase separation with a special D/D:A/A structure (P-i-N-type component distribution) is also formed. As a result, compared to the 16.43% power conversion efficiency (PCE) of the bulk heterojunction devices, such control enables bilayer OSC devices based on the polymer D18 and L8-BO to deliver an enhanced PCE of 18.02% with simultaneously improved short-circuit current density, open-circuit voltage, and fill factor. Importantly, it is also demonstrated in these results that the LBL deposition process utilizing the pre-aggregation of polymer and its fiber-network-forming ability is a very promising approach to improve charge dynamics, suppress carrier recombination, and fabricate highly efficient OSCs.

14 SOLAR ENERGY↗