Search NASA⌕ Search

SEARCH · Search NASA

Results for “sensor modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Method of Forming a Hot Film Sensor System on a Model

A method of forming a hot film sensor directly on a model is provided. A polyimide solution is sprayed onto the model. The model so sprayed is then heated in air. The steps of spraying and heating are repeated until a polyimide film of desired thickness is achieved on the model. The model with the polyimide film thereon is then thoroughly dried in air. One or more hot film sensors and corresponding electrical conducting leads are then applied directly onto the polyimide film.

Tran, Sang Q.↗
NASA NTRS2009

Modeling, Detection, and Disambiguation of Sensor Faults for Aerospace Applications

Sensor faults continue to be a major hurdle for systems health management to reach its full potential. At the same time, few recorded instances of sensor faults exist. It is equally difficult to seed particular sensor faults. Therefore, research is underway to better understand the different fault modes seen in sensors and to model the faults. The fault models can then be used in simulated sensor fault scenarios to ensure that algorithms can distinguish between sensor faults and system faults. The paper illustrates the work with data collected from an electro-mechanical actuator in an aerospace setting, equipped with temperature, vibration, current, and position sensors. The most common sensor faults, such as bias, drift, scaling, and dropout were simulated and injected into the experimental data, with the goal of making these simulations as realistic as feasible. A neural network based classifier was then created and tested on both experimental data and the more challenging randomized data sequences. Additional studies were also conducted to determine sensitivity of detection and disambiguation efficacy to severity of fault conditions.

Balaban, Edward↗
DOE OSTI2020

Frequency-domain hot-wire sensor and 3D model for thermal conductivity measurements of reactive and corrosive materials at high temperatures

High temperature solids and liquids are becoming increasingly important in next-generation energy and manufacturing systems that seek higher efficiencies and lower emissions. Accurate measurements of thermal conductivity at high temperatures are required for the modeling and design of these systems, but commonly employed time-domain measurements can have errors from convection, corrosion, and ambient temperature fluctuations. Here, we describe the development of a frequency-domain hot-wire technique capable of accurately measuring the thermal conductivity of solid and molten compounds from room temperature up to 800 °C. Therefore, by operating in the frequency-domain, we can lock into the harmonic thermal response of the material and reject the influence of ambient temperature fluctuations, and we can keep the probed volume below 1 µl to minimize convection. The design of the microfabricated hot-wire sensor, electrical systems, and insulating wire coating to protect against corrosion is covered in detail. Furthermore, we discuss the development of a full three-dimensional multilayer thermal model that accounts for both radial conduction into the sample and axial conduction along the wire and the effect of wire coatings. The 3D, multilayer model facilitates the measurement of small sample volumes important for material development. A sensitivity analysis and an error propagation calculation of the frequency-domain thermal model are performed to demonstrate what factors are most important for thermal conductivity measurements. Finally, we show thermal conductivity measurements including model data fitting on gas (argon), solid (sulfur), and molten substances over a range of temperatures.

47 OTHER INSTRUMENTATION↗
NASA NTRS1981

Model degradation effects on sensor failure detection

This paper discusses the effects of imperfect modeling on the detection and isolation of sensor failures. For systems with non-zero set points, deterministic inputs or non-zero noise biases, the model mismatch appears as a bias on the stochastic innovation process. This bias, if left unaccounted for, would be sufficient to declare a false alarm failure in one or more sensors. A practical design procedure based upon the Generalized Likelihood Ratio (GLR) form uses a finite data window sequential t-test to detect and isolate model mismatch effects and soft sensor failures. Application to an eighth order model of the QCSEE turbofan engine is discussed.

Leininger, G. G.↗
NASA NTRS1993

Active Thermal Isolation For Hot-Film Anemometers

Local heating compensates for conduction of heat from sensors into modules. Two hot-film sensors stacked on wind-tunnel model. Outer sensor detects changes in boundary-layer flow. Inner sensor provides active thermal isolation between outer sensor and model. Thermal boundary condition controlled at response time of detection hot-film sensor, significantly less than response time of internally heated model. Requires less power to maintain outer hot-film sensor at given temperature, enabling system to respond over greater dynamic range before power limits of instrument reached. Stacked sensors bonded to surface of most wind-tunnel models, even to curved surfaces, and removed after completion of experiments.

Martinson, Scott D.↗
DOE OSTI2021

Sensor impact evaluation and verification for fault detection and diagnostics in building energy systems: A review

Sensors are the key information source for fault detection and diagnostics (FDD) in buildings. However, sensors are often not properly designed, installed, calibrated, located, and maintained, which negatively impacts FDD performance. Several sensor-related FDD topics have been widely studied, covering a wide range of fault types and applications. However, it is difficult to get a clear picture of the technical development of sensor-related topics in FDD. A systematic review of sensor topics is needed to summarize the existing research in a logical way, draw conclusions on the current development, and predict the future development of sensors in building FDD. To address this gap, we conducted a comprehensive literature review of more than 100 FDD-sensor-related papers. In this article, we subdivide the FDD tasks into building-level, system-level, and component-level FDD, and review sensor-related topics in each category. Our major conclusions are: (a) current data-driven FDD research focuses more on FDD algorithms than sensors, (b) sensor “hardware” research topics are less studied than sensor “software” topics, (c) very few papers focus on sensor engineering as an integral aspect of FDD development, and (d) some important sensor topics, such as sensor cost-effectiveness and sensor schema/layout/location, are not well studied. Finally, we discuss the need for a systematic framework of FDD sensors and models to integrate sensor design/selection, sensor data analysis/mining, feature selection, physics-based or data-driven algorithm development, sensor fault detection, sensor calibration, and sensor maintenance. Finally, expert interviews are conducted to validate the above findings and conclusions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1990

Development of a sensor coordinated kinematic model for neural network controller training

A robotic benchmark problem useful for evaluating alternative neural network controllers is presented. Specifically, it derives two camera models and the kinematic equations of a multiple degree of freedom manipulator whose end effector is under observation. The mapping developed include forward and inverse translations from binocular images to 3-D target position and the inverse kinematics of mapping point positions into manipulator commands in joint space. Implementation is detailed for a three degree of freedom manipulator with one revolute joint at the base and two prismatic joints on the arms. The example is restricted to operate within a unit cube with arm links of 0.6 and 0.4 units respectively. The development is presented in the context of more complex simulations and a logical path for extension of the benchmark to higher degree of freedom manipulators is presented.

Jorgensen, Charles C.↗
NASA NTRS1993

The Enhanced-model Ladar Wind Sensor and Its Application in Planetary Wind Velocity Measurements

For several years we have been developing an optical air-speed sensor that has a clear application as a meteorological wind-speed sensor for the Mars landers. This sensor has been developed for aircraft use to replace the familiar, pressure-based Pitot probe. Our approach utilizes a new concept in the laser-based optical measurement of air velocity (the Enhanced-Mode Ladar), which allows us to make velocity measurements with significantly lower laser power than conventional methods. The application of the Enhanced-Mode Ladar to measuring wind speeds in the martian atmosphere is discussed.

Soreide, D. C.↗
NASA NTRS1997

Wake Vortex Radar System Development: Overview

The objectives of the work are to: (1) Investigate microwave and millimeter wave sensors to locate, track, quantify, and observe the wake vortex hazard; (2) Develop and evaluate system concepts and designs using sensor system models and employing a theoretical reflectivity model for the wake vortex; (3) Test the validity of the theoretical model; (4) Acquire sensor systems and conduct field testing to evaluate; and to (5) Refine a system for field testing as a wake vortex sensor.

Neece, Robert T.↗
NASA NTRSDate not supplied

Air Quality Analysis with Sensors, Satellites, and Models

Poor air quality is a major global public health concern, which is only projected to get worse in coming years. A comprehensive understanding of current and potential future air quality and its key drivers spanning from local to global scales is needed to tackle this important problem. This presentation will outline the sources of information that we use to understand air quality, including ground-based measurements, satellites, and models. After giving an overview of these data sources and outlining their strengths and limitations, we will take a look at how they can be used together to give us a better picture of air quality locally and globally.

Carl Malings↗
NASA NTRSDate not supplied

Air Quality Data Fusion with Sensors, Satellites, and Models

Global forecasting models, satellite remote sensing, and ground-based regulatory and low-cost monitors all have strengths and weaknesses with respect to providing locally relevant information about air quality. This presentation will give a brief overview of these data sources and then discuss a method for combining them via data fusion to support near-real-time air quality estimation and forecasting at sub-city scales. The basic idea behind the approach will be summarized, followed by an update on recent developments towards creating an operational system using Google Earth Engine and on quantifying uncertainties related to data fusion outputs.

Carl Malings↗