Results for “shape memory” — Page 9

DOE OSTI2026

PET waste- and bio-derived imine vitrimers for shape-memory, intrinsic flame-retardant, and recyclable carbon fiber composites

Developing circular multifunctional vitrimers and carbon fiber–reinforced polymers (CFRPs) that are simultaneously recyclable, mechanically robust, and intrinsically flame retardant remains a major challenge. Here, in this study, we report multifunctional vitrimers and their carbon fiber–reinforced vitrimer (CFRV) composites, where the vitrimer design integrates closed-loop recyclability, enhanced interfacial adhesion, and intrinsic flame retardancy within a single materials platform. The vitrimer matrix is synthesized from post-consumer polyethylene terephthalate (PET) waste and a vanillin-derived phosphorus-containing crosslinker, forming an imine-based network. The resulting vitrimer resin exhibits high tensile strength, thermal healability, repeated reprocessability, programmable shape memory, and rapid chemical depolymerization under mild conditions. Amine-functionalized carbon fibers significantly improve fiber–matrix interfacial bonding, yielding CFRVs with tensile strengths up to 789 MPa and complete recovery of structurally intact fibers after chemical recycling. The phosphorus-rich aromatic network further imparts intrinsic flame retardancy, enabling self-extinguishing behavior without external additives. This work advances a materials design paradigm for next-generation multifunctional, sustainable vitrimers and CFRVs, while simultaneously addressing the recycling challenges associated with both plastic and CFRP waste.

Bio-derived crosslinker↗

NASA NTRS2014

Shape Memory Alloy (SMA)-Based Launch Lock

Most NASA missions require the use of a launch lock for securing moving components during the launch or securing the payload before release. A launch lock is a device used to prevent unwanted motion and secure the controlled components. The current launch locks are based on pyrotechnic, electro mechanically or NiTi driven pin pullers and they are mostly one time use mechanisms that are usually bulky and involve a relatively high mass. Generally, the use of piezoelectric actuation provides high precession nanometer accuracy but it relies on friction to generate displacement. During launch, the generated vibrations can release the normal force between the actuator components allowing shaft's free motion which could result in damage to the actuated structures or instruments. This problem is common to other linear actuators that consist of a ball screw mechanism. The authors are exploring the development of a novel launch lock mechanism that is activated by a shape memory alloy (SMA) material ring, a rigid element and an SMA ring holding flexure. The proposed design and analytical model will be described and discussed in this paper.

launch lock↗

NASA NTRS2008

Self-Deploying Trusses Containing Shape-Memory Polymers

Composite truss structures are being developed that can be compacted for stowage and later deploy themselves to full size and shape. In the target applications, these smart structures will precisely self-deploy and support a large, lightweight space-based antenna. Self-deploying trusses offer a simple, light, and affordable alternative to articulated mechanisms or inflatable structures. The trusses may also be useful in such terrestrial applications as variable-geometry aircraft components or shelters that can be compacted, transported, and deployed quickly in hostile environments. The truss technology uses high-performance shape-memory-polymer (SMP) thermoset resin reinforced with fibers to form a helical composite structure. At normal operating temperatures, the truss material has the structural properties of a conventional composite. This enables truss designs with required torsion, bending, and compression stiffness. However, when heated to its designed glass transition temperature (Tg), the SMP matrix acquires the flexibility of an elastomer. In this state, the truss can be compressed telescopically to a configuration encompassing a fraction of its original volume. When cooled below Tg, the SMP reverts to a rigid state and holds the truss in the stowed configuration without external constraint. Heating the materials above Tg activates truss deployment as the composite material releases strain energy, driving the truss to its original memorized configuration without the need for further actuation. Laboratory prototype trusses have demonstrated repeatable self-deployment cycles following linear compaction exceeding an 11:1 ratio (see figure).

Schueler, Robert M.↗

NASA NTRS2001

Variable area nozzle for gas turbine engines driven by shape memory alloy actuators

A gas turbine engine includes a variable area nozzle having a plurality of flaps. The flaps are actuated by a plurality of actuating mechanisms driven by shape memory alloy (SMA) actuators to vary fan exist nozzle area. The SMA actuator has a deformed shape in its martensitic state and a parent shape in its austenitic state. The SMA actuator is heated to transform from martensitic state to austenitic state generating a force output to actuate the flaps. The variable area nozzle also includes a plurality of return mechanisms deforming the SMA actuator when the SMA actuator is in its martensitic state.

Rey, Nancy M.↗

NASA NTRS2013

Thermo-Mechanical Methodology for Stabilizing Shape Memory Alloy Response

This innovation is capable of significantly reducing the amount of time required to stabilize the strain-temperature response of a shape memory alloy (SMA). Unlike traditional stabilization processes that take days to weeks to achieve stabilized response, this innovation accomplishes stabilization in a matter of minutes, thus making it highly useful for the successful and practical implementation of SMA-based technologies in real-world applications. The innovation can also be applied to complex geometry components, not just simple geometries like wires or rods.

Padula, Santo↗

NASA NTRS2018

General Background on Shape Memory Alloys

This is an overview talk being given at Parker Hannifin in an effort to begin new collaboration, given by the NASA GRC Shape Memory Alloy (SMA) Team.

Padula, Santo, II↗

NASA NTRS2004

Design and Control of a Proof-of-Concept Active Jet Engine Intake Using Shape Memory Alloy Actuators

The design and control of a novel proof-of-concept active jet engine intake using Nickel-Titanium (Ni-Ti or Nitinol) shape memory alloy (SMA) wire actuators is used to demonstrate the potential of an adaptive intake to improve the fuel efficiency of a jet engine. The Nitinol SMA material is selected for this research due to the material's ability to generate large strains of up to 5 percent for repeated operations, a high power-to-weight ratio, electrical resistive actuation, and easy fabrication into a variety of shapes. The proof-of-concept engine intake employs an overlapping leaf design arranged in a concentric configuration. Each leaf is mounted on a supporting bar that rotates upon actuation by SMA wires electrical resistive heating. Feedback control is enabled through the use of a laser range sensor to detect the movement of a leaf and determine the radius of the intake area. Due to the hysteresis behavior inherent in SMAs, a nonlinear robust controller is used to direct the SMA wire actuation. The controller design utilizes the sliding-mode approach to compensate for the nonlinearities associated with the SMA actuator. Feedback control experiments conducted on a fabricated proof-of-concept model have demonstrated the capability to precisely control the intake area and achieve up to a 25 percent reduction in intake area. The experiments demonstrate the feasibility of engine intake area control using the proposed design.

Song, Gangbing↗

NASA NTRSDate not supplied

Towards Accurate and Efficient Predictions of Martensitic Transition Temperatures for Shape Memory Alloys from First Principles

Recent rapid progresses in physics theory and computational power have made it possible to predict the martensitic transition temperatures (MTTs) in shape memory alloys (SMAs) from first principles [1-3]. In particular, rigorous while time-consuming thermodynamic integration has been employed to compute the anharmonic phonon free energies, which play a crucial role in determining martensitic phase transitions in SMAs. However, this approach has only been applied to simple binaries, and its accuracy is unsatisfying for certain SMAs such as the most commonly used NiTi. In this work, we report on several new developments to our method that bring first-principles theory and experiment much closer into agreement including the MTT of NiTi, and that improve the computational efficiency significantly. We have applied our refined approach to investigate the Ni0.5Ti0.5-xHfx and PdxNi0.5-xTi0.5 ternaries, and the predicted MTT for each composition is within 100K compared with experiment. We will address various techniques to overcome the difficulty encountered in studying ternaries. Our theoretical approach is expected to be a broadly applicable and predictive theory for designing complex SMAs with desirable properties. [1] J.B. Haskins, A.E. Thompson,and J.W. Lawson, Phys. Rev B 94, 214110 (2016). [2] J.B. HaskinsandJ.W. Lawson, J. App. Phys. 121, 205103 (2017). [3] J.B. Haskins, H. Malmir, S. J. Honrao, L. A. Sandoval, and J.W. Lawson, Acta Materialia 212, 116872 (2017).

Zhigang Wu↗

NASA NTRSDate not supplied

Towards Accurate and Efficient Predictions of Martensitic Transition Temperatures for Shape Memory Alloys from First Principles

Recent rapid progresses in physics theory and computational power have made it possible to predict the martensitic transition temperatures (MTTs) in shape memory alloys (SMAs) from first principles [1-3]. In particular, rigorous while time-consuming thermodynamic integration has been employed to compute the anharmonic phonon free energies, which play a crucial role in determining martensitic phase transitions in SMAs. However, this approach has only been applied to simple binaries, and its accuracy is unsatisfying for certain SMAs such as the most commonly used NiTi. In this work, we report on several new developments to our method that bring first-principles theory and experiment much closer into agreement including the MTT of NiTi, and that improve the computational efficiency significantly. We have applied our refined approach to investigate the Ni0.5Ti0.5-xHfx and PdxNi0.5-xTi0.5 ternaries, and the predicted MTT for each composition is within 100K compared with experiment. We will address various techniques to overcome the difficulty encountered in studying ternaries. Our theoretical approach is expected to be a broadly applicable and predictive theory for designing complex SMAs with desirable properties.

Zhigang Wu↗

NASA NTRS2005

System-Level Design of a Shape Memory Alloy Actuator for Active Clearance Control in the High-Pressure Turbine

This paper describes results of a numerical analysis evaluating the feasibility of high-temperature shape memory alloys (HTSMA) for active clearance control actuation in the high-pressure turbine section of a modern turbofan engine. The prototype actuator concept considered here consists of parallel HTSMA wires attached to the shroud that is located on the exterior of the turbine case. A transient model of an HTSMA actuator was used to evaluate active clearance control at various operating points in a test bed aircraft engine simulation. For the engine under consideration, each actuator must be designed to counteract loads from 380 to 2000 lbf and displace at least 0.033 inches. Design results show that an actuator comprised of 10 wires 2 inches in length is adequate for control at critical engine operating points and still exhibits acceptable failsafe operability and cycle life. A proportional-integral-derivative (PID) controller with integrator windup protection was implemented to control clearance amidst engine transients during a normal mission. Simulation results show that the control system exhibits minimal variability in clearance control performance across the operating envelope. The final actuator design is sufficiently small to fit within the limited space outside the high-pressure turbine case and is shown to consume only small amounts of bleed air to adequately regulate temperature.

DeCastro, Jonathan A.↗

NASA NTRS2018

Design and Development of CubeSat Solar Array Deployment Mechanisms Using Shape Memory Alloys

The Advanced eLectrical Bus (ALBus) project is a technology demonstration mission of a 3U CubeSat with an advanced, digitally controlled electrical power system capability and the novel use of Shape Memory Alloy (SMA) technology for reliable solar array (SA) deployable mechanisms. The ALBus CubeSat deploys four SAs in addition to the body-mounted arrays on each side of the CubeSat. A goal of the mission is to utilize the SMAs being developed at the NASA Glenn Research Center to deploy these SAs. The use of SMAs allows for the ability to test and reset the flight deployment mechanism prior to flight, which reduces the risk of in orbit deployment failures common to CubeSats. As a result, an SMA-driven Retention and Release (R&R) mechanism and an SMA-driven hinge were designed, developed, and integrated for flight. This paper summarizes the development of these mechanisms, types and functionalities of the SMAs used, as well as the lessons learned throughout the process.

cubesat↗

NASA NTRS2019

Utilizing Shape Memory Alloys for Novel, Non-Pneumatic Tire Design - Designing for the Best of Both Worlds

Materials are a fundamental building block that often get overlooked as a critical component that shapes our world. Numerous products that impact our lives are enabled by the materials from which they are made. With regard to Martian and lunar rover applications, conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. Solid, rigid wheels suffer from the inability to handle the high, localized loads while encountering rugged terrain and also produce relatively poor traction and operating efficiency. In an effort to overcome these problems, non-pneumatic, compliant tire designs are being developed, using Nickel-Titanium (NiTi), a thermally activated shape memory alloy (SMA), that is less sensitive to temperature and exhibits much greater plastic deformation than do conventional vulcanized rubber pneumatic tires.

Padula, Santo, II↗

NASA NTRS2019

Utilizing Shape Memory Alloys for Novel, Non-Pneumatic Tire Design - Designing for the Best of Both Worlds

Materials are a fundamental building block that often get overlooked as a critical component that shapes our world. Numerous products that impact our lives are enabled by the materials from which they are made. With regard to Martian and lunar rover applications, conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. Solid, rigid wheels suffer from the inability to handle the high, localized loads while encountering rugged terrain and also produce relatively poor traction and operating efficiency. In an effort to overcome these problems, non-pneumatic, compliant tire designs are being developed, using Nickel-Titanium (NiTi), a thermally activated shape memory alloy (SMA), that is less sensitive to temperature and exhibits much greater plastic deformation than do conventional vulcanized rubber pneumatic tires.

Padula, Santo, II↗

NASA NTRS2018

Design and Development of CubeSat Solar Array Deployment Mechanisms Using Shape Memory Alloys

The Advanced eLectrical Bus (ALBus) project is a technology demonstration mission of a 3-U CubeSat with an advanced, digitally controlled electrical power system capability and the novel use of Shape Memory Alloy (SMA) technology for reliable solar array deployable mechanisms. The ALBus cubesat has a need to deploy four solar arrays in addition to the body-mounted arrays on each side of the cubesat. A goal of the mission is to utilize the SMAs being developed at the NASA Glenn Research Center to deploy these solar arrays. The use of SMAs allows for the ability to test and reset the flight deployment mechanism prior to flight which reduces the risk of on orbit deployment failures common on cubesats. As a result, an SMA driven Retention and Release mechanism and an SMA driven hinge was designed, developed, and being prepared for flight. This paper summarized the development of these mechanisms, types and functionalities of SMAs used, and lessons learned throughout the process.

solar array deployment↗

NASA NTRS2024

Martensitic Phase Transition in Complex NiTi-Based Shape Memory Alloys from First-Principles Calculations

Recent rapid progresses in physics theory and computational power have made it possible to accurately predict the phase transitions and martensitic transition temperatures (MTTs) in shape memory alloys (SMAs) from first principles. However, previously theory and calculations [1-4] were applied only to study highly ordered stoichiometric binary alloys such as NiTi, PdTi and NiHf. Here we report on our recent first-principles investigations [5,6] on Ni 0.5 Ti 0.5-x Hf x and Pd x Ni 0.5-x Ti 0.5 ternaries and off-stoichiometric NiTi, and the predicted martensitic phase transitions in these complex SMAs are in good agreement with experimental findings. In particular, the calculated MTTs for all these compositions are within 100 K compared with the corresponding measured data, and our results also reveal the origin of the striking asymmetry in MTT of the off-stoichiometric NiTi near equiatomic compositions. We will address various techniques to overcome the difficulty encountered in studying ternaries and off-stoichiometic binaries associated with disorder and/or much lowered symmetry. Our theoretical approach is expected to be a broadly applicable and predictive theory for designing complex SMAs with desirable properties. References: [1] J. B. Haskins, A. E. Thompson, and J. W. Lawson, Phys. Rev B 94 , 214110 (2016). [2] J. B. Haskins and J. W. Lawson, J. App. Phys. 121 , 205103 (2017). [3] J. B. Haskins, H. Malmir, S. J. Honrao, L. A. Sandoval, and J. W. Lawson, Acta Materialia 212 , 116872 (2017). [4] Z. Wu, J. W. Lawson, and O. Benafan, Phys. Rev. B 106 , L140102 (2022). [5] Z. Wu, H. Malmir, O. Benafan, and J. W. Lawson, Acta Materialia 261 , 119362 (2023). [6] Z. Wu, J. W. Lawson, and O. Benafan, Phys. Rev. B 108 , L140103 (2023).

Zhigang Wu↗

NASA NTRS2000

Shape Memory Alloy Actuator

The present invention discloses and teaches a unique, remote optically controlled micro actuator particularly suitable for aerospace vehicle applications wherein hot gas, or in the alternative optical energy, is employed as the medium by which shape memory alloy elements are activated. In gas turbine powered aircraft the source of the hot gas may be the turbine engine compressor or turbine sections.

Robert J Baumbick↗

NASA NTRS2002

Shape Memory Alloy Actuator

The present invention discloses and teaches a unique, remote optically controlled micro actuator particularly suitable for aerospace vehicle applications wherein hot gas, or in the alternative optical energy, is employed as the medium by which shape memory alloy elements are activated. In gas turbine powered aircraft the source of the hot gas may be the turbine engine compressor or turbine sections.

Robert J Baumbick↗

NASA NTRS2006

Development and Characterization of Improved NiTiPd High-Temperature Shape-Memory Alloys by Solid-Solution Strengthening and Thermomechanical Processing

The need for compact, solid-state actuation systems for use in the aerospace, automotive, and other transportation industries is currently motivating research in high-temperature shape-memory alloys (HTSMA) with transformation temperatures greater than 100 C. One of the basic high-temperature alloys investigated to fill this need is Ni(19.5)Ti(50.5)Pd30. Initial testing has indicated that this alloy, while having acceptable work characteristics, suffers from significant permanent deformation (or ratcheting) during thermal cycling under load. In an effort to overcome this deficiency, various solid-solution alloying and thermomechanical processing schemes were investigated. Solid-solution strengthening was achieved by substituting 5at% gold or platinum for palladium in Ni(19.5)Ti(50.5)Pd30, the so-called baseline alloy, to strengthen the martensite and austenite phases against slip processes and improve thermomechanical behavior. Tensile properties, work behavior, and dimensional stability during repeated thermal cycling under load for the ternary and quaternary alloys were compared. The relative difference in yield strength between the martensite and austenite phases and the dimensional stability of the alloy were improved by the quaternary additions, while work output was only minimally impacted. The three alloys were also thermomechanically processed by cycling repeatedly through the transformation range under a constant stress. This so-called training process dramatically improved the dimensional stability in these samples and also recovered the slight decrease in work output caused by quaternary alloying. An added benefit of the solid-solution strengthening was maintenance of enhanced dimensional stability of the trained material to higher temperatures compared to the baseline alloy, providing a greater measure of over-temperature capability.

Bigelow, Glen↗