SEARCH · Search NASA

Results for “software differences”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Computational Fluid Dynamics Study on the Effects of RATO Timing on the Scale Model Acoustic Test

The Scale Model Acoustic Test (SMAT) is a 5% scale test of the Space Launch System (SLS), which is currently being designed at Marshall Space Flight Center (MSFC). The purpose of this test is to characterize and understand a variety of acoustic phenomena that occur during the early portions of lift off, one being the overpressure environment that develops shortly after booster ignition. The SLS lift off configuration consists of four RS-25 liquid thrusters on the core stage, with two solid boosters connected to each side. Past experience with scale model testing at MSFC (in ER42), has shown that there is a delay in the ignition of the Rocket Assisted Take Off (RATO) motor, which is used as the 5% scale analog of the solid boosters, after the signal to ignite is given. This delay can range from 0 to 16.5ms. While this small of a delay maybe insignificant in the case of the full scale SLS, it can significantly alter the data obtained during the SMAT due to the much smaller geometry. The speed of sound of the air and combustion gas constituents is not scaled, and therefore the SMAT pressure waves propagate at approximately the same speed as occurs during full scale. However, the SMAT geometry is much smaller allowing the pressure waves to move down the exhaust duct, through the trench, and impact the vehicle model much faster than occurs at full scale. To better understand the effect of the RATO timing simultaneity on the SMAT IOP test data, a computational fluid dynamics (CFD) analysis was performed using the Loci/CHEM CFD software program. Five different timing offsets, based on RATO ignition delay statistics, were simulated. A variety of results and comparisons will be given, assessing the overall effect of RATO timing simultaneity on the SMAT overpressure environment.

Nielsen, Tanner↗

NASA NTRS2019

Supersonic Engine Inlet Tone Noise Radiation

A computational and experimental acoustic analysis was conducted on a supersonic engine inlet geometry with a spike center body and an auxiliary inlet. Simulations performed using two different commercial acoustics software packages were compared to a scale model experiment conducted using an ultrasonic fan noise simulator. Both the experiment and simulations were run at discrete circumferential mode and frequency combinations to identify strengths and weaknesses of each method. For cases where a single azimuthal mode was well cut on throughout the length of the duct, reasonable agreement was found between the three methods. In cases with more complicated acoustic effects, the experimental results became intractable when considered alone and the simulations were needed for interpreting the results. The peak sound level and the peak angle of the far field radiation vary widely when changing modes and frequencies. The objective of the study is to develop a validated workflow for simulation of fan tone noise through supersonic inlet geometries for community noise predictions.

Stephens, David B.↗

NASA NTRS2017

The Design of the Reference Orbit for NISAR, the NASA-ISRO Synthetic Aperture Radar Mission

The NISAR mission plans to use a 12-day-repeating sun-synchronous orbit for repeat-pass interferometry at multiple time scales using SAR data. For the interferometry to work the radar measurements must be made from within a critical baseline, which happens if all of the orbits are maintained to be within a fixed tube around a reference orbit. This paper describes the choice of dynamical models used in defining such a reference orbit, the perturbative effects of dynamics not considered in the repeat orbit, and the process of designing the orbit to repeat. We also describe our method for sharing the repeat orbit among multiple mission participants who use different models and software.

Hatch, Sara J.↗

NASA NTRS2017

The Design of the Reference Orbit for NISAR, the NASA-ISRO Synthetic Aperture Radar Mission

Hatch, Sara J.↗

NASA NTRSDate not supplied

A Quantum Volume Metric for Qudit Quantum Computers

Qudit-based quantum computers, such as the high-Q superconducting radio frequency resonator cavities being pursued by the SQMS Center hosted at Fermilab, may provide computational advantages relative to qubit-based machines for some problems. However, the novel system’s hardware and software will present different errors that must be understood and mitigated, along with other unforeseen inefficiencies across the entire stack. It is essential to benchmark these qudit platforms against existing systems. We propose such a benchmark by generalizing the qubit-based quantum volume metric to qudit devices. In particular, we show that the performance depends on the available gateset used to compile unitary operations, as well as realistic noise sources.

Quantum Computing↗

NASA NTRSDate not supplied

Interoperability of Tools at the CCMC

The CCMC has a diverse set of tools in many languages that support utilization of simulation outputs accessible through CCMC interactive archives. Some model output post-processing and analysis tools are delivered to tCCMC by the community. One such model output post-processing/utilization tool developed by the CCMC is the open source Kamodo package. Kamodo is developed primarily in Python (with some C) and has already established strong interoperability with other Python libraries inside PyHC and out. While that interoperability is important, interoperability with other languages and tools is as important. Many models are written in Fortran or C, and their ability to pull in data from a Python tool or export directly to other analysis software in a different language will greatly increase scientific productivity. Interoperability within Python is important, but broader interoperability is just as important.

CCMC↗

NASA NTRS2005

Thermal System Verification and Model Validation for NASA's Cryogenic Passively Cooled James Webb Space Telescope

A thorough and unique thermal verification and model validation plan has been developed for NASA s James Webb Space Telescope. The JWST observatory consists of a large deployed aperture optical telescope passively cooled to below 50 Kelvin along with a suite of several instruments passively and actively cooled to below 37 Kelvin and 7 Kelvin, respectively. Passive cooling to these extremely low temperatures is made feasible by the use of a large deployed high efficiency sunshield and an orbit location at the L2 Lagrange point. Another enabling feature is the scale or size of the observatory that allows for large radiator sizes that are compatible with the expected power dissipation of the instruments and large format Mercury Cadmium Telluride (HgCdTe) detector arrays. This passive cooling concept is simple, reliable, and mission enabling when compared to the alternatives of mechanical coolers and stored cryogens. However, these same large scale observatory features, which make passive cooling viable, also prevent the typical flight configuration fully-deployed thermal balance test that is the keystone to most space missions thermal verification plan. JWST is simply too large in its deployed configuration to be properly thermal balance tested in the facilities that currently exist. This reality, when combined with a mission thermal concept with little to no flight heritage, has necessitated the need for a unique and alternative approach to thermal system verification and model validation. This paper describes the thermal verification and model validation plan that has been developed for JWST. The plan relies on judicious use of cryogenic and thermal design margin, a completely independent thermal modeling cross check utilizing different analysis teams and software packages, and finally, a comprehensive set of thermal tests that occur at different levels of JWST assembly. After a brief description of the JWST mission and thermal architecture, a detailed description of the three aspects of the thermal verification and model validation plan is presented.

Cleveland, Paul E.↗

NASA NTRS2011

The Correlation of Interphase Chromatin Structure with the Radiation-Induced Inter- and Intrachromosome Exchange Hotspots

To investigate the relationship between chromosome aberrations induced by radiation and chromatin folding, we reconstructed three dimensional structure of chromosome 3 and measured the physical distances between different regions of the chromosome. Previously, we have investigated the location of breaks involved in inter- and intrachromosomal type exchange events in human chromosome 3, using the multicolor banding in situ hybridization (mBAND) technique. In human epithelial cells exposed to both low- and high-LET radiations in vitro, we reported that intra-chromosome exchanges occurred preferentially between a break in the 3p21 and one in the 3q11 regions, and the breaks involving in inter-chromosome exchanges occurred in two regions towards the telomeres of the chromosome. Exchanges were also observed between a break in 3p21 and one in 3q26, but few exchanges were observed between breaks in 3q11 and 3q26, even though the two regions are located on the same arm of the chromosome. In this study, human epithelial cells were fixed at G1 phase and the interphase cells were hybridized using the XCyte3 mBAND kit from MetaSystems. The z-section images of chromosome 3 were captured with a Leica and an LSM 510 Meta laser scanning confocal microscopes. A total of 100 chromosomes were analyzed. The reconstruction of three dimensional structure of interphase chromosome 3 with six different colored regions was achieved using the Imaris software. The relative distance between different regions was measured as well. We further analyzed fragile sites on the chromosome that have been identified in various types of cancers. The data showed that, in majority of the cells, the regions containing 3p21 and 3q11 are colocalized in the center of the chromosome, whereas, the regions towards the telomeres of the chromosome are either physically wrapping outside the chromosome center or with arms sticking out. Our results demonstrated that the distribution of breaks involved in radiation-induced inter and intra-chromosome aberrations depends upon both the location of fragile sites and the folding of chromatins.

Zhang, Ye↗

NASA NTRS2010

Strain System for the Motion Base Shuttle Mission Simulator

The Motion Base Shuttle Mission Simulator (MBSMS) Strain System is an innovative engineering tool used to monitor the stresses applied to the MBSMS motion platform tilt pivot frames during motion simulations in real time. The Strain System comprises hardware and software produced by several different companies. The system utilizes a series of strain gages, accelerometers, orientation sensor, rotational meter, scanners, computer, and software packages working in unison. By monitoring and recording the inputs applied to the simulator, data can be analyzed if weld cracks or other problems are found during routine simulator inspections. This will help engineers diagnose problems as well as aid in repair solutions for both current as well as potential problems.

Huber, David C.↗

DOE OSTI2024

Platform for Integrated Land use And Transportation Experiments and Simulation (PILATES) v1.0

PILATES allows for flexibly and at-scale coupling of multiple models to allow for multi-scale and multi-resolution simulation of regional-scale transport networks. In particular, it couples the MATSim-derived transportation modeling framework for Behavior, Energy, Autonomy and Mobility (BEAM) with other models operating at different time scales. Rather than tightly coupling supply and demand models using shared agents and memory within the same software process, PILATES orchestrates different model runs in a containerized framework. This structure requires passing information from the demand models to BEAM in the format of a synthetic population and agent plans, and from BEAM to the demand models in terms or origin/destination tables (also known as "skims"). This allows it to take advantage of the behavioral sophistication of existing activity-based models as well as the reinforcement learning structure of MATSim replanning and adopted by BEAM, in a way that requires minimal changes to existing models. It also takes advantage of the computational performance of BEAM, which allows for simulations with millions of agents to complete in reasonable time as well as allowing for detailed mechanistic simulation of the operation of on-demand modes.

Needell, Zachary↗

NASA NTRS1988

An overview of very high level software design methods

Very High Level design methods emphasize automatic transfer of requirements to formal design specifications, and/or may concentrate on automatic transformation of formal design specifications that include some semantic information of the system into machine executable form. Very high level design methods range from general domain independent methods to approaches implementable for specific applications or domains. Applying AI techniques, abstract programming methods, domain heuristics, software engineering tools, library-based programming and other methods different approaches for higher level software design are being developed. Though one finds that a given approach does not always fall exactly in any specific class, this paper provides a classification for very high level design methods including examples for each class. These methods are analyzed and compared based on their basic approaches, strengths and feasibility for future expansion toward automatic development of software systems.

Asdjodi, Maryam↗

DOE OSTI2025

Feature review of photovoltaic modeling software utilizing blind performance assessment

While confidence in photovoltaic (PV) modeling software has always been essential, the rapid pace of new PV plant developments makes accuracy and credibility more critical than ever. Independent assessments, particularly through blind modeling comparisons, are therefore necessary to ensure unbiased benchmarking across PV modeling software. Previous studies have been limited by a narrow range of models compared, anonymized results, or system size. This study presents results from the first-ever onymous blind modeling comparison, evaluated using both lab- and utility-scale fixed-tilt, monofacial, south-facing systems at sub-hourly time intervals. Seven commercially used PV software tools were compared: 3E SynaptiQ, PlantPredict, PVsyst, RatedPower, SAM, SolarFarmer, and Solargis Evaluate. Predictions were submitted directly by software representatives, providing unique insights into each software’s implementation and resulting prediction behavior. Notable features, including plane-of-array (POA) transposition model, module temperature model, shading model, and performance model were analyzed and compared. Four summary tables compile these features of the software, serving as a resource to help users understand the methodological differences and select the most suitable software for their applications. The software tools show deviations from mean error in annual yield up to 2.5 % in the lab-scale system, increasing to 6.0 % for the utility-scale system. These differences arise from a combination of user decisions and the inherent behavior of the software, indicating the need for continuous and rigorous validation of modeling methods using these software tools against complex, real-world systems.

14 SOLAR ENERGY↗

NASA NTRS1989

Hierarchical Ada robot programming system (HARPS)- A complete and working telerobot control system based on the NASREM model

HARPS is a telerobot control system that can perform some simple but useful tasks. This capability is demonstrated by performing the ORU exchange demonstration. HARPS is based on NASREM (NASA Standard Reference Model). All software is developed in Ada, and the project incorporates a number of different CASE (computer-aided software engineering) tools. NASREM was found to be a valid and useful model for building a telerobot control system. Its hierarchical and distributed structure creates a natural and logical flow for implementing large complex robust control systems. The ability of Ada to create and enforce abstraction enhanced the implementation of such control systems.

Leake, Stephen↗

NASA NTRS2007

Tracking-Data-Conversion Tool

Object Oriented Data Technology (OODT) is a software framework for creating a Web-based system for exchange of scientific data that are stored in diverse formats on computers at different sites under the management of scientific peers. OODT software consists of a set of cooperating, distributed peer components that provide distributed peer-topeer (P2P) services that enable one peer to search and retrieve data managed by another peer. In effect, computers running OODT software at different locations become parts of an integrated data-management system.

Flora-Adams, Dana↗

NASA NTRS2007

Software Framework for Peer Data-Management Services

Object Oriented Data Technology (OODT) is a software framework for creating a Web-based system for exchange of scientific data that are stored in diverse formats on computers at different sites under the management of scientific peers. OODT software consists of a set of cooperating, distributed peer components that provide distributed peer-to-peer (P2P) services that enable one peer to search and retrieve data managed by another peer. In effect, computers running OODT software at different locations become parts of an integrated data-management system.

Hughes, John↗

NASA NTRS2010

PLOT3D Export Tool for Tecplot

The PLOT3D export tool for Tecplot solves the problem of modified data being impossible to output for use by another computational science solver. The PLOT3D Exporter add-on enables the use of the most commonly available visualization tools to engineers for output of a standard format. The exportation of PLOT3D data from Tecplot has far reaching effects because it allows for grid and solution manipulation within a graphical user interface (GUI) that is easily customized with macro language-based and user-developed GUIs. The add-on also enables the use of Tecplot as an interpolation tool for solution conversion between different grids of different types. This one add-on enhances the functionality of Tecplot so significantly, it offers the ability to incorporate Tecplot into a general suite of tools for computational science applications as a 3D graphics engine for visualization of all data. Within the PLOT3D Export Add-on are several functions that enhance the operations and effectiveness of the add-on. Unlike Tecplot output functions, the PLOT3D Export Add-on enables the use of the zone selection dialog in Tecplot to choose which zones are to be written by offering three distinct options - output of active, inactive, or all zones (grid blocks). As the user modifies the zones to output with the zone selection dialog, the zones to be written are similarly updated. This enables the use of Tecplot to create multiple configurations of a geometry being analyzed. For example, if an aircraft is loaded with multiple deflections of flaps, by activating and deactivating different zones for a specific flap setting, new specific configurations of that aircraft can be easily generated by only writing out specific zones. Thus, if ten flap settings are loaded into Tecplot, the PLOT3D Export software can output ten different configurations, one for each flap setting.

Alter, Stephen↗

NASA NTRS1988

Resource utilization during software development

This paper discusses resource utilization over the life cycle of software development and discusses the role that the current 'waterfall' model plays in the actual software life cycle. Software production in the NASA environment was analyzed to measure these differences. The data from 13 different projects were collected by the Software Engineering Laboratory at NASA Goddard Space Flight Center and analyzed for similarities and differences. The results indicate that the waterfall model is not very realistic in practice, and that as technology introduces further perturbations to this model with concepts like executable specifications, rapid prototyping, and wide-spectrum languages, we need to modify our model of this process.

Zelkowitz, Marvin V.↗

NASA NTRS1989

Chemical calculations on Cray computers

The influence of recent developments in supercomputing on computational chemistry is discussed with particular reference to Cray computers and their pipelined vector/limited parallel architectures. After reviewing Cray hardware and software the performance of different elementary program structures are examined, and effective methods for improving program performance are outlined. The computational strategies appropriate for obtaining optimum performance in applications to quantum chemistry and dynamics are discussed. Finally, some discussion is given of new developments and future hardware and software improvements.

Taylor, Peter R.↗