SEARCH · Search NASA

Results for “subsonic tests”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2011

Instrumentation Development for Large Scale Hypersonic Inflatable Aerodynamic Decelerator Characterization

Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology is currently being considered for multiple atmospheric entry applications as the limitations of traditional entry vehicles have been reached. The Inflatable Re-entry Vehicle Experiment (IRVE) has successfully demonstrated this technology as a viable candidate with a 3.0 m diameter vehicle sub-orbital flight. To further this technology, large scale HIADs (6.0 8.5 m) must be developed and tested. To characterize the performance of large scale HIAD technology new instrumentation concepts must be developed to accommodate the flexible nature inflatable aeroshell. Many of the concepts that are under consideration for the HIAD FY12 subsonic wind tunnel test series are discussed below.

Swanson, Gregory T.↗

NASA NTRS1991

Preliminary flight evaluation of an engine performance optimization algorithm

A performance seeking control (PSC) algorithm has undergone initial flight test evaluation in subsonic operation of a PW 1128 engined F-15. This algorithm is designed to optimize the quasi-steady performance of an engine for three primary modes: (1) minimum fuel consumption; (2) minimum fan turbine inlet temperature (FTIT); and (3) maximum thrust. The flight test results have verified a thrust specific fuel consumption reduction of 1 pct., up to 100 R decreases in FTIT, and increases of as much as 12 pct. in maximum thrust. PSC technology promises to be of value in next generation tactical and transport aircraft.

Lambert, H. H.↗

NASA NTRS1975

Experimental and theoretical low speed aerodynamic characteristics of the NACA 65 sub 1-213, alpha equals 0.50, airfoil

Low-speed wind-tunnel tests have been conducted to determine the two-dimensional aerodynamic characteristics of the NACA 65 sub 1-213, a = 0.05, airfoil. The results were compared with data from another low-speed wind tunnel and also with theoretical predictions obtained by using a viscous subsonic method. The tests were conducted over a Mach number range from 0.10 to 0.36. Reynolds numbers based on the airfoil chord varied from about 3 million to 23 million.

Beasley, W. D.↗

NASA NTRS1991

Preliminary flight evaluation of an engine performance optimization algorithm

A performance-seeking control (PSC) algorithm has undergone initial flight test evaluation in subsonic operation of a PW 1128-engined F-15; this algorithm is designed to optimize the quasi-steady performance of an engine for three primary modes: (1) minimum fuel consumption, (2) minimum fan-turbine inlet temperature (FTIT), and (3) maximum thrust. The flight test results have verified a thrust-specific fuel consumption reduction of 1 percent, up to 100 R decreases in FTIT, and increases of as much as 12 percent in maximum thrust. PSC technology promises to be of value in next-generation tactical and transport aircraft.

Lambert, H. H.↗

NASA NTRS2005

High altitude subsonic parachute field programmable gate array

This paper describes a rapid, top down requirements-driven design of an FPGA used in an Earth qualification test program for a new Mars subsonic parachute. The FPGA is used to process and control storage of telemetry data from multiple sensors throughout; launch, ascent, deployment and descent phases of the subsonic parachute test.

FPGA methodology↗

NASA NTRS1956

Zero-angle-of-attack Performance of Two-dimensional Inlets near Mach Number 3

An extensive program was undertaken to investigate the effect of several geometric variables on the performance of two-dimensional inlets. This investigation included inlets having single-wedge, double-wedge, and isentropic compression ramps with various side-plate configurations and subsonic diffusers. The tests were conducted over a range of Reynolds number based on inlet height from 0.50 to 2.67(sup x)10(sup 6). Generally, the performance levels of the two-dimensional inlets were somewhat below those obtained previously with comparable axisymmetric models. At Mach number 3.05 the optimum total-pressure recovery was obtained with an isentropic inlet which compressed the external flow to a Mach number of 1.88. Rectangular side plates and a long high-exit-Mach-number subsonic diffuser with filleted corners were used with this inlet. A critical total-pressure recovery of 0.71 was realized with a corresponding mass-flow ratio of 0.965. Subcritical stability to a mass-flow ratio of 0.60 was obtained.

Woollett, Richard R↗

NASA NTRSDate not supplied

Preliminary Measurement of Pitch Damping of Blunt Entry Vehicles in a Subsonic Magnetic Suspension Wind Tunnel

Blunt bodies have been magnetically suspended in a 6-inch octagonal test-section low-subsonic wind tunnel in a free-to oscillate configuration. Capsule oscillations of two entry vehicle geometries were measured from high speed video of repeated test runs. An analytical solution to the 1degree-of-freedom equations of motion was fit to the measured oscillation histories to solve for a pitch damping coefficient. A six degree-of-freedom simulation was used to predict the wind tunnel data and assess the effect of magnetic forces on capsule dynamics. The predicted effect was used in the data reduction methodology to improved the pitch damping measurement. Pitch damping measurements are compared with heritage forced oscillation data and are in good agreement. Preliminary uncertainties are included with recommendations for improved data reduction.

Dynamic Stability↗

NASA NTRSDate not supplied

Methodology for Validation of Unsteady Pressure-Sensitive Paint Measurements using Pressure Transducers

Unsteady Pressure-Sensitive Paint (uPSP) technology provides simultaneously high-frequency and high-spatial resolution surface pressure fluctuation measurements. It has demonstrated value in wind tunnel test facilities to evaluate aerospace vehicle unsteady aerodynamics. The calibration of measurements from digital pixel counts into corresponding physical units relies on both lab-based and in-situ calibration steps, and its validation is both challenging and critical to adoption of the technology. We present a rigorous methodology for direct comparison of uPSP-derived surface pressure measurements to reference pressure transducer data based on a model of the camera-based measurement error, a model of the flow field pressure signal, and their propagation through the uPSP data reduction algorithm. The methodology is demonstrated on data collected in a small-scale, subsonic wind tunnel test as well as data collected from a Space Launch System unsteady aerodynamics characterization test at the NASA Ames Research Center Unitary Plan Wind Tunnel Complex.

Pressure-Sensitive Paint↗

NASA NTRSDate not supplied

Validating uPSP with Transducers

Pressure-Sensitive Paint↗

NASA NTRS2011

Ares I Aerodynamic Testing at the Boeing Polysonic Wind Tunnel

Throughout three full design analysis cycles, the Ares I project within the Constellation program has consistently relied on the Boeing Polysonic Wind Tunnel (PSWT) for aerodynamic testing of the subsonic, transonic and supersonic portions of the atmospheric flight envelope (Mach=0.5 to 4.5). Each design cycle required the development of aerodynamic databases for the 6 degree-of-freedom (DOF) forces and moments, as well as distributed line-loads databases covering the full range of Mach number, total angle-of-attack, and aerodynamic roll angle. The high fidelity data collected in this facility has been consistent with the data collected in NASA Langley s Unitary Plan Wind Tunnel (UPWT) at the overlapping condition ofMach=1.6. Much insight into the aerodynamic behavior of the launch vehicle during all phases of flight was gained through wind tunnel testing. Important knowledge pertaining to slender launch vehicle aerodynamics in particular was accumulated. In conducting these wind tunnel tests and developing experimental aerodynamic databases, some challenges were encountered and are reported as lessons learned in this paper for the benefit of future crew launch vehicle aerodynamic developments.

Pinier, Jeremy T.↗

NASA NTRS2007

Flight Test of the F/A-18 Active Aeroelastic Wing Airplane

A viewgraph presentation of flight tests performed on the F/A active aeroelastic wing airplane is shown. The topics include: 1) F/A-18 AAW Airplane; 2) F/A-18 AAW Control Surfaces; 3) Flight Test Background; 4) Roll Control Effectiveness Regions; 5) AAW Design Test Points; 6) AAW Phase I Test Maneuvers; 7) OBES Pitch Doublets; 8) OBES Roll Doublets; 9) AAW Aileron Flexibility; 10) Phase I - Lessons Learned; 11) Control Law Development and Verification & Validation Testing; 12) AAW Phase II RFCS Envelopes; 13) AAW 1-g Phase II Flight Test; 14) Region I - Subsonic 1-g Rolls; 15) Region I - Subsonic 1-g 360 Roll; 16) Region II - Supersonic 1-g Rolls; 17) Region II - Supersonic 1-g 360 Roll; 18) Region III - Subsonic 1-g Rolls; 19) Roll Axis HOS/LOS Comparison Region II - Supersonic (open-loop); 20) Roll Axis HOS/LOS Comparison Region II - Supersonic (closed-loop); 21) AAW Phase II Elevated-g Flight Test; 22) Region I - Subsonic 4-g RPO; and 23) Phase II - Lessons Learned

Voracek, David↗

NASA NTRS1975

Effects of jet exhaust gas properties on exhaust simulation and afterbody drag

The effect of varying the jet exhaust's ratio of specific heats, gas constant, and temperature on airplane afterbody drag was investigated. Jet exhaust simulation parameters were evaluated also. Subsonic and transonic tests were made using a single nacelle model with afterbodies having boattail angles of 10 deg and 20 deg. Besides air, three other jet exhaust gases were investigated. The ratios of specific heats, gas constants, and total temperatures of the four exhaust gases ranged from 1.40 to 1.26, 287 to 376 J/kg-K, and 300 to 1013 K, respectively. For steep boattail angles, and transonic speeds and typical turbojet pressure ratios, the current data indicate that the use of air to simulate a dry turbojet exhaust can result in an overprediction of afterbody drag as high as 17 percent of the dry turbojet value.

Compton, W. B., III↗

NASA NTRS1978

Status and operational characteristics of the National Transonic Facility

The article discusses the development and capabilities of the National Transonic Facility which is planned for operation in 1981. The fan-drive, cryogenic-pressurized, closed-return facility will have operating parameters of: 0.1-1.2 Mach, 1-9 bars pressure, 78-340 K, 150 dB sound pressure, and plus or minus 0.001 rms turbulence intensity. These operating conditions have been selected on the basis of several current and future aircraft and space transportation systems. The facility will provide full-scale testing conditions for calculating subsonic drag, airloads, and stability and control information. Data for pre-test conditions, on-line information, and post-test analysis will be computer-processed.

Nicks, O. W.↗

NASA NTRS1978

External insulator for liquid hydrogen tanks

With optimized insulation thickness, tank temperatures were always below 311 K (100 F). This conclusion indicated that an aluminum tank could be used with an optimized insulation system if desired. The N2 purged systems were always lighter than CO2 purged systems. The lower condensation temperature was the controlling factor. Closed cell foam systems were lightest. Closed cell foams, in spite of their need for protective outer insulation, produced insulation systems which were lighter than systems which allowed cryodeposition. Foam system durability established for TMAX = 316 K (110 F). Tests for a subsonic application established this durability; higher temperature limit foam durability was unknown at this. An increase in foam TMAX from 316 K (110 F) to 450 K (350 F) potentially decreased TPS mass by 25 percent.

Sharpe, E. L.↗

NASA NTRS1981

Cap protects aircraft nose cone

Inexpensive, easily fabricated cap protects aircraft nose cone from erosion. Made of molded polycarbonate, cap has been flight tested at both subsonic and supesonic speeds. Its strength and erosion characteristics are superior to those of fiberglass cones.

Bryan, C. F., Jr.↗

NASA NTRS1980

Performance improvement of delta wings at subsonic speeds due to vortex flaps

Subsonic wind tunnel tests were conducted to determine performance improvements possible from the use of leading edge vortex flaps (LEVF) on delta wings. Various flap sizes and deflection angles were examined and lift-to-drag ratio improvements of up to 40% were found at moderate angles of attack on 60 deg and 75 deg swept wings. The LEVF is concluded to be effective in moving the wing's leading edge vortex onto the flaps, tilting the vortex-induced force vector forward to produce a thrust or reduce the wing's drag while maintaining attached flow and lift on the wing's upper surface.

Marchman, J. F., III↗

NASA NTRS1981

Exploratory subsonic investigation of vortex-flap concept on arrow wing configuration

The drag reduction potential of a vortex flap concept, utilizing the thrust contribution of separation vortices maintained over leading edge flap surfaces, was explored in subsonic wind tunnel tests on a highly swept arrow wing configuration. Several flap geometries were tested in comparison with a previous study on the same model with leading edges drooped for attached flow. The most promising vortex flap arrangements produced drag reductions comparable with leading edge droop over a range of lift coefficients from 0.3 to 0.6 (untrimmed), and also indicated beneficial effects in the longitudinal and lateral static stability characteristics.

Rao, D. M.↗

NASA NTRS1981

The aerodynamics of circulation control

Two dimensional subsonic wind tunnel tests were conducted on a 20% thickness: chord ratio circulation controlled elliptic aerofoil section equipped with forward and reverse blowing slots. Overall performance measurements were made over a range of trailing edge blowing momentum coefficients from 0 to 0.04; some included the effect of leading edge blowing. A detailed investigation of the trailing edge wall jet, using split film probes, hot wire probes and total head tubes, provided measurements of mean velocity components, Reynolds normal and shear stresses, and radial static pressure. The closure of the two dimensional angular momentum and continuity equations was examined using the measured data, with and without correction, and the difficulty of obtaining a satisfactory solution illustrated. Suggestions regarding the nature of the flow field which should aid the understanding of Coanda effect and the theoretical solution of highly curved wall jet flows are presented.

Wood, N. J.↗