SEARCH · Search NASA

Results for “supercapacitor energy storage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Fully Conjugated Poly(phthalocyanine) Scaffolds Derived from a Mechanochemical Approach Towards Enhanced Energy Storage

Phthalocyanines (Pc)-derived materials represent an attractive category of porous organic scaffolds featured by extensive π-conjugated networks, but their construction is still limited to the solution-based pathways, producing materials with inferior conductivity and porosity. Herein, a mechanochemistry-driven approach was developed leveraging the on-surface polymerization of aromatic nitrile monomers with ortho-positioned dicyano groups in the presence of metal catalysts (magnesium, zinc, or aluminum) under neat and ambient conditions. Diverse Pc-functionalized conjugated porous networks (Pc-CPNs) were obtained featured by extensively and fully π-conjugated skeletons, high surface areas, and hierarchical porosities. The monomers in this mechanochemical approach could be extended to those difficult to be handled in solution-based procedures. In this work, the Pc-CPNs displayed attractive electrochemical performance as supercapacitor and anodes in batteries, together with superb long-term stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Engineering of Self‐Aggregation‐Resistant MnO 2 Heterostructure with A Built‐in Field for Enhanced High‐Mass‐Loading Energy Storage

Abstract Although MnO 2 has been intensively investigated for energy storage, further applications are limited by van der Waals force‐triggered self‐aggregation that always leads to poorly exposed active sites and compromised reaction dynamics, especially under high‐mass‐loading conditions. Herein, by synergistically coupling interfacial modulation with the Kirkendall effect, this work achieves in situ topological structure reorganization of MnOOH toward the high‐aspect‐ratio MnO 2 heterostructure (Heter‐MnO 2 ) with fully exposed active sites, which is ready to assemble into self‐supporting high‐mass‐loading film (30 mg cm −2 ) with restrained self‐aggregation. Theoretical calculation and dynamics analysis results demonstrate the generation of the built‐in field within the heterostructure, thus enhancing the electronic‐transfer and ionic‐adsorption/transport rates. As such, the 30 mg cm −2 Heter‐MnO 2 electrode achieves a superior areal capacitance of 4762 mF cm −2 at 1 mA cm −2 and a sound rate performance (79% at 100 mA cm −2 ) comparable to those of low‐mass‐loading/thin‐film electrodes. As a proof of concept, the fabricated planar interdigital quasi‐solid‐state symmetric micro‐supercapacitor (MSC) based on the Heter‐MnO 2 electrode can deliver a remarkable areal capacitance of 181 mF cm −2 and a considerable volumetric energy density of 10.3 mWh cm −3 . This methodology highlights the promise of surface/interface chemistry modulation for the configuration of easy‐to‐integrate hierarchical nanostructures to better meet practical energy applications.

Chemistry↗

DOE OSTI2020

Supramolecular Energy Materials

Self-assembly is a bioinspired strategy to craft materials for renewable and clean energy technologies. In plants, the alignment and assembly of the light-harvesting protein machinery in the green leaf optimize the ability to efficiently convert light from the sun to form chemical bonds. In artificial systems, strategies based on self-assembly using noncovalent interactions offer the possibility to mimic this functional correlation among molecules to optimize photocatalysis, photovoltaics, and energy storage. Here, one of the long-term objectives of the field described here as supramolecular energy materials is to learn how to design soft materials containing light-harvesting assemblies and catalysts to generate fuels and useful chemicals. Supramolecular energy materials also hold great potential in the design of systems for photovoltaics in which intermolecular interactions in self-assembled structures, for example, in electron donor and acceptor phases, maximize charge transport and avoid exciton recombination. Possible pathways to integrate organic and inorganic structures by templating strategies and electrodeposition to create materials relevant to energy challenges including photoconductors and supercapacitors are also described. The final topic discussed is the synthesis of hybrid perovskites in which organic molecules are used to modify both structure and functions, which may include chemical stability, photovoltaics, and light emission.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Versatile Graphitized Carbon Nanofibers in Energy Applications

Graphitized carbon nanofibers (CNFs) are the allotropic forms of carbon that offer exceptional electrical conductivity, high aspect ratio, large surface-to-volume ratio, flexibility, mechanical robustness, and structural stability. These properties render CNFs as useful materials in energy applications, including water electrocatalysis and electrochemical energy storage devices (EESDs). Graphitized CNFs manifest huge versatility in EESDs and have been employed as electrode materials, as supports for other electrode materials, and conductive additives. This perspective summarizes the production methods, structural aspects, and energy applications of graphitized CNFs. Different design strategies have been employed to produce CNFs with diverse and distinct morphologies and structures. Their fabrication methods, along with precursors and dopants or cocatalysts, impact the overall structural, functional, and topographical properties. Recent developments on the state-of-the-art interests of graphitic CNFs in lithium-ion batteries (LIBs), lithium–sulfur (Li–S) batteries, vanadium redox flow batteries (VRFBs), supercapacitors, and water splitting have explored the many possibilities in energy sectors. Finally, the assembly and functioning of CNFs in water splitting and EESDs as well as primary challenges are discussed in this perspective.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Emerging Modification Technologies of Lignin-based Activated Carbon toward Advanced Applications

Lignin-based activated carbon (LAC) is a promising high-quality functional material due to high surface area, abundant porous structure, and various functional groups. Modification is the most important step to functionalize LAC by altering its porous and chemical properties. Here, this Review summarizes the state-of-the-art modification technologies of LAC toward advanced applications. Promising modification approaches are reviewed to display their effects on the preparation of LAC. The multiscale changes in the porosity and the surface chemistry of LAC are fully discussed. Advanced applications are then introduced to show the potential of LAC for supercapacitor electrode, catalyst support, hydrogen storage, and carbon dioxide capture. Finally, the mechanistic structure-function relationships of LAC are elaborated. These results highlight that modification technologies play a special role in altering the properties and defining the functionalities of LAC, which could be a promising porous carbon material toward industrial applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

3D printing of metal-based materials for renewable energy applications

Large-scale renewable energy must overcome conversion and storage challenges before it can replace fossil fuels due to its intermittent nature. However, current sustainable energy devices still suffer from high cost, low efficiency, and poor service life problems. Recently, porous metal-based materials have been widely used as desirable cross-functional platforms for electrochemical and photochemical energy systems for their unique electrical conductivity, catalytic activity, and chemical stability. To tailor the porosity length scale, ordering, and compositions, 3D printing has been applied as a disruptive manufacturing revolution to create complex architected components by directly joining sequential layers into designed structures. In conclusion, this article intends to summarize cutting-edge advances of metal-based materials for renewable energy devices (e.g., fuel cells, solar cells, supercapacitors, and batteries) over the past decade.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Direct Correlation of the Salt-Reduced Diffusivities of Organic Solvents with the Solvent’s Mole Fraction

We report that lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) in organic solvents (especially propylene carbonate) has demonstrated extraordinary pseudocapacitive performance as an electrolyte in the supercapacitor configuration. However, the influence of the solvated ions on the diffusivity of the solvent molecules is yet to be understood. We examine the impact of LiTFSI on the diffusivity in five organic solvents: acetonitrile (ACN), tetrahydrofuran (THF), methanol (MeOH), dimethyl sulfoxide (DMSO), and propylene carbonate (PC) using a combination of neutron scattering, conductivity measurements, and molecular dynamics simulations. The extent of the diffusivity reduction in the concentration regime of ≤1 M directly correlates with the solvent mole fraction at which the solvation shells around Li + ions are of similar size in all the solvents, resulting in a universal ~50% reduction in the solvent diffusivity. These results provide guidance for formulation of the new electrolytes to enhance the performance of energy storage devices.

conductivity↗

DOE OSTI2024

Artificial-Intelligence Aided Design and Synthesis of Novel Layered 2D Multi-Principal Element Materials for Energy Storage (Final Report)

This DOE-EPSCoR project aimed to predict, synthesize, and characterize novel layered two-dimensional (2D) high-entropy materials (HEMs). These 2D-HEMs, composed of multiple principal elements in nearly equal concentrations, are distinct from traditional 2D materials (typically containing two or three elements) and conventional alloys (dominated by a single primary element with minor secondary additions). Their unique structural and compositional features enable significant lattice strain accommodation, resulting in enhanced electrode performance and potential applications in catalysis, hydrogen storage, sensing, quantum information technologies, and flexible electronics. The research focused on addressing four fundamental questions: (i) What combinations of elements can form stable and synthesizable 2D-HEMs? (ii) What mechanisms drive the stability and synthesizability of crystalline single-phase 2D-HEMs? (iii) How do local chemical disorder and defects influence the macroscopic electronic and mechanical properties? and (iv) What charge storage mechanisms are active in selectively synthesized 2D-HEMs for battery and supercapacitor electrode applications? To achieve these goals, the project employed an integrated theory-experiment approach, incorporating high-throughput first-principles calculations, theoretical modeling, data mining, experimental synthesis, and advanced characterization techniques. The advanced computing resources and state-of-the-art experimental characterization facilities at Oak Ridge National Laboratory (ORNL) were leveraged through collaboration. Beyond scientific advancements, the project contributed to workforce development. Two postdoctoral researchers and three graduate students at the University of Maine were trained through co-advising by ORNL scientists and collaborative interactions, strengthening their expertise in cutting-edge materials science.

36 MATERIALS SCIENCE↗

NASA NTRS2011

Substituted Quaternary Ammonium Salts Improve Low-Temperature Performance of Double-Layer Capacitors

Double-layer capacitors are unique energy storage devices, capable of supporting large current pulses as well as a very high number of charging and discharging cycles. The performance of doublelayer capacitors is highly dependent on the nature of the electrolyte system used. Many applications, including for electric and fuel cell vehicles, back-up diesel generators, wind generator pitch control back-up power systems, environmental and structural distributed sensors, and spacecraft avionics, can potentially benefit from the use of double-layer capacitors with lower equivalent series resistances (ESRs) over wider temperature limits. Higher ESRs result in decreased power output, which is a particular problem at lower temperatures. Commercially available cells are typically rated for operation down to only 40 C. Previous briefs [for example, Low Temperature Supercapacitors (NPO-44386), NASA Tech Briefs, Vol. 32, No. 7 (July 2008), p. 32, and Supercapacitor Electrolyte Solvents With Liquid Range Below 80 C (NPO-44855), NASA Tech Briefs, Vol. 34, No. 1 (January 2010), p. 44] discussed the use of electrolytes that employed low-melting-point co-solvents to depress the freezing point of traditional acetonitrile-based electrolytes. Using these modified electrolyte formulations can extend the low-temperature operational limit of double-layer capacitors beyond that of commercially available cells. This previous work has shown that although the measured capacitance is relatively insensitive to temperature, the ESR can rise rapidly at low temperatures, due to decreased electrolyte conductance within the pores of the high surface- area carbon electrodes. Most of these advanced electrolyte systems featured tetraethylammonium tetrafluoroborate (TEATFB) as the salt. More recent work at JPL indicates the use of the asymmetric quaternary ammonium salt triethylmethylammonium tetrafluoroborate (TEMATFB) or spiro-(l,l')-bipyrrolidium tetrafluoroborate (SBPBF4) in a 1:1 by volume solvent mixture of acetonitrile (AN) and methyl formate (MF) enables double-layer capacitor cells to operate well below -40 C with a relatively low ESR. Typically, a less than twofold increase in ESR is observed at -65 C relative to room-temperature values, when these modified electrolyte blends are used in prototype cells. Double-layer capacitor coin cells filled with these electrolytes have displayed the lowest measured ESR for an organic electrolyte to date at low temperature (based on a wide range of electrolyte screening studies at JPL). The cells featured high-surface-area (approximately equal to 2,500 m/g) carbon electrodes that were 0.50 mm thick and 1.6 cm in diameter, and coated with a thin layer of platinum to reduce cell resistance. A polyethylene separator was used to electrically isolate the electrodes.

Brandon, Erik J.↗

DOE OSTI2023

Fabrication of hybrid tin oxide‐cellulose nanocomposite as the flexible and thin supercapacitor

Abstract Microfibrillated cellulose (MFC) with reinforcing effects is a useful building block in the fabrication of flexible and thin supercapacitors. Herein, a hybrid tin oxide‐cellulose nanocomposite was hydrothermally produced and coated on MFC thin films to form a supercapacitor. The hybrid tin oxide‐cellulose thin films were structurally analyzed using scanning electrode microscopy, Fourier transform infrared spectroscopy and x‐ray diffraction. The cellulose thin film with the highest loading of hybrid tin oxide‐cellulose nanocomposite exhibited a specific capacitance of 225.88 F g −1 at 100 mV s −1 and 486.38 F g −1 at 20 mV s −1 in the three‐electrode electrochemical system. In addition, it revealed good cyclic stability up to 40 cycles run continuously with 95% cyclic retention. The high specific capacitance and superior cyclic stability could be related to the enhanced charge mobility and ion diffusion between the solid and electrolyte interface. The cellulose thin film coated with flower‐like hybrid nanocomposite showed great potential in energy storage.

Letchumanan, Iswary↗

DOE OSTI2021

Chemical Heterointerface Engineering on Hybrid Electrode Materials for Electrochemical Energy Storage

Abstract The chemical heterointerfaces in hybrid electrode materials play an important role in overcoming the intrinsic drawbacks of individual materials and thus expedite the in‐depth development of electrochemical energy storage. Benefiting from the three enhancement effects of accelerating charge transport, increasing the number of storage sites, and reinforcing structural stability, the chemical heterointerfaces have attracted extensive interest and the electrochemical performances of hybrid electrode materials have been significantly optimized. In this review, recent advances regarding chemical heterointerface engineering in hybrid electrode materials are systematically summarized. Especially, the intrinsic behaviors of chemical heterointerfaces on hybrid electrode materials are refined based on built‐in electric field, van der Waals interaction, lattice mismatch and connection, electron cloud bias and chemical bond, and their combination. The strategies for introducing chemical heterointerfaces are classified into in situ local transformation, in situ growth, cosynthesis, and other strategy. The recent progress about the chemical heterointerfaces engineering specially focusing on metal‐ion batteries, supercapacitors, and Li–S batteries are introduced in detail. Furthermore, the classification and characterization of chemical heterointerfaces are briefly described. Finally, the emerging challenges and perspectives about future directions of chemical heterointerface engineering are proposed.

Li, Wenbin↗

DOE OSTI2023

Corn stover‐derived porous carbon for asymmetric supercapacitors

In this investigation, hydrothermal liquefaction‐derived hydrochar from pulverized corn stover (avg. particle size 1.12 mm and ash content 6.75 wt%) is chemically activated with aqueous KOH in the presence of Pluronic F127 surfactant and thermally treated further up to 800°C to generate porous carbon (POC) with higher specific surface area and porosity. POC obtained under different processing conditions is thoroughly characterized by Brunauer‐Emmett‐Teller surface area analyzer, Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Metallic impurity present in POC is characterized by inductively coupled plasma mass spectrometry. Higher specific surface area POC is observed with the use of the surfactant during the activation process. Fully characterized POC is used with (Mn, Ti)‐mixed oxide electrode to fabricate asymmetric supercapacitor (ASC). Specific capacitance of ASC is measured by cyclic voltammetry (CV) technique using Gamry G‐300 potentiostat/galvanostat/ZRA. CV plots are obtained with different voltage scan rates whereas galvanostatic charge‐discharge plots are studied by varying the current density. Renewable corn stover‐derived POC prepared using Pluronic F127/KOH activation method is found to be highly suitable as an electrode material because of higher capacitance and electrochemical stability over 100 charging‐discharging cycles.

25 ENERGY STORAGE↗

DOE OSTI2020

Keratin-derived functional carbon with superior charge storage and transport for high-performance supercapacitors

In this work, we report a scalable method to synthesize hierarchically porous, hetero-atom doped activated carbon nanosheet from waste biomass-human hair, and demonstrates the use of this carbon as an ultra-high performance electrode material for supercapacitor applications. Microscopic analyses reveal that sheet size ranges from 50 to 200 nm having a thickness of 15–27 nm. As-synthesized, carbon nanosheets possess a hierarchical porous structure having a specific surface area of 1548 m 2 g -1 . Heteroatom concentration (nitrogen, oxygen, and sulfur) of around 25% is confirmed from XPS analysis. Therefore, the novel interconnected hierarchical porous nanosheets structure enables fast adsorption and transportation of ions during electrochemical processes. Also, the abundant chemically available electroactive heteroatom species in the material enhance the wettability of ions and contribute to pseudocapacitance. The electrochemical analyses through cyclic voltammetry and galvanostatic charge-discharge measurements in 6 M KOH reveal the quasi-EDLC behavior of the activated carbons due to the presence of heteroatoms. A reprensentative KOH activated carbon shows an excellent specific capacitance value of 999 F g -1 at a current density of 1 A g -1 . Furthermore, the symmetrically assembled two-electrode device also delivers a maximum energy density of 32 W h Kg -1 at a power density of 325 W Kg -1 . In addition, excellent cyclic stability of 98% capacitance retention is observed after 10,000 continuous GCD cycles even at a high current density of 5 A g -1 . Symmetric flexible supercapacitor device using KOH-PVA-K3FeCN6 as redox gel polymer electrolyte shows a synergistic specific capacitance of 145 mF cm -1 at a current density of 0.8 mA cm -1 exhibiting very less deviation in bending mode. Therefore, this waste biomass derived heteroatom doped hierarchical porous carbon nanosheets can be a promising material for cost-effective high- performance supercapacitor.

42 ENGINEERING↗

NASA NTRS2023

Emperor's new clothes: Novel textile-based supercapacitors using sheep wool fiber as electrode substrate

Textile-based supercapacitors (TSCs) are being used to meet the ever-increasing demand for mobile, safe, and convenient energy sources to power personal electronic devices. To that end, the smart textiles used in wearable technology need to be made from highly conductive yarns that are easily manufacturable. To date, synthetic- and cellulosic-based yarns have been exclusively used for the fabrication of TSCs, while other yarns have not been explored. Here, we used conductive protein-based yarns for TSCs and report on the use of wool coated with Ti 3 C 2 T x MXene as a potential electrode material. To knit TSCs, wool and cotton yarns were coated with MXene flakes and their surfaces were characterized using Scanning Electron Microscopy (SEM) and X-Ray Photoelectron Spectroscopy (XPS). The electrochemical characterization was conducted to examine the performance of wool- and cotton-based MXene electrodes as substrates and determine charge storage and resistive behavior. These tests showed that wool TSCs exhibited more pseudocapacitive behavior, while cotton TSCs exhibited a wider current range. At a scan rate of 5 mV/s, cotton TSCs presented an areal capacitance of 823.9 mF/cm 2 while this value for the wool TSCs was 284 mF/cm 2 . The performance of yarns was also tested under various mechanical deformation conditions and after washing in order to assess the stability of TSCs. This study indicates the potential of protein-based yarns as electrode substrates for integration of MXene to fabricate smart textile-based devices.

Alyssa Grube↗

DOE OSTI2022

Effects of dilution in ionic liquid supercapacitors

Room-temperature ionic liquids (RTILs) are synthetic electrolytes that have a large electrochemical stability window, making them attractive candidates for electric double-layer capacitor (EDLC) applications. Due to their high viscosities and low ionic conductivities, RTILs are often diluted with organic solvent for practical use. Here, we study the effects of dilution on the performance of RTIL EDLCs using a simple mean-field model. We find that dilution diminishes the unfavorable hysteresis that results from a spontaneous surface charge separation (SSCS). As a result, the RTIL concentration can be used to modulate the proximity to the SSCS transition, and maximize capacitance. The interplay between the concentration and the correlation strength gives rise to complex zero-potential phase behavior, including a tricritical point and a λ-line, very similar to the Blume–Capel dilute Ising model. Additionally, electrodes that are solvophilic aid in the prevention of SSCS by drawing solvent molecules to the electrode and displacing ions. Solvophilic electrodes give rise to a phase transition at finite potential where the surface charge rapidly increases with a small increase in potential, leading to a substantial increase in capacitance and energy storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Enhanced Rate Capability of Ion‐Accessible Ti 3 C 2 T x ‐NbN Hybrid Electrodes

Abstract Although 2D Ti 3 C 2 T x is a good candidate for supercapacitors, the restacking of nanosheets hinders the ion transport significantly at high scan rates, especially under practical mass loading (>10 mg cm −2 ) and thickness (tens of microns). Here, Ti 3 C 2 T x ‐NbN hybrid film is designed by self‐assembling Ti 3 C 2 T x with 2D arrays of NbN nanocrystals. Working as an interlayer spacer of Ti 3 C 2 T x , NbN facilitates the ion penetration through its 2D porous structure; even at extremely high scan rates. The hybrid film shows a thickness‐independent rate performance (almost the same rate capabilities from 2 to 20 000 mV s −1 ) for 3 and 50 µm thick electrodes. Even a 109 µm thick Ti 3 C 2 T x ‐NbN electrode shows a better rate performance than 25 µm thick pure Ti 3 C 2 T x electrodes. This method may pave a way to controlling ion transport in electrodes composed of 2D conductive materials, which have potential applications in high‐rate energy storage and beyond.

Wang, Hao↗

DOE OSTI2020

Maximizing ion accessibility in MXene-knotted carbon nanotube composite electrodes for high-rate electrochemical energy storage

Improving the accessibility of ions in the electrodes of electrochemical energy storage devices is vital for charge storage and rate performance. In particular, the kinetics of ion transport in organic electrolytes is slow, especially at low operating temperatures. Herein, we report a new type of MXene-carbon nanotube (CNT) composite electrode that maximizes ion accessibility resulting in exceptional rate performance at low temperatures. The improved ion transport at low temperatures is made possible by breaking the conventional horizontal alignment of the two-dimensional layers of the MXene Ti 3 C 2 by using specially designed knotted CNTs. The large, knot-like structures in the knotted CNTs prevent the usual restacking of the Ti 3 C 2 flakes and create fast ion transport pathways. The MXene-knotted CNT composite electrodes achieve high capacitance (up to 130 F g -1 (276 F cm -3 )) in organic electrolytes with high capacitance retention over a wide scan rate range of 10 mV s -1 to 10 V s -1 . This study is also the first report utilizing MXene-based supercapacitors at low temperatures (down to -60 °C).

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS2012

Low Temperature Double-layer Capacitors with Improved Energy Density: An Overview of Recent Development Efforts

Electrochemical double-layer capacitors are finding increased use in a wide range of energy storage applications, particularly where high pulse power capabilities are required. Double-layer capacitors store charge at a liquid/solid interface, making them ideal for low temperature power applications, due to the facile kinetic processes associated with the rearrangement of the electrochemical double-layer at these temperatures. Potential low temperature applications include hybrid and electric vehicles, operations in polar regions, high altitude aircraft and aerospace avionics, and distributed environmental and structural health monitoring. State-of-the-art capacitors can typically operate to -40 C, with a subsequent degradation in power performance below room temperature. However, recent efforts focused on advanced electrolyte and electrode systems can enable operation to temperatures as low as -70 C, with capacities similar to room temperature values accompanied by reasonably low equivalent series resistances. This presentation will provide an overview of recent development efforts to extend and improve the wide temperature performance of these devices.

Supercapacitors↗