Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface impedance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Moderate temperature detector development

P-side backside reflecting constant, photodiode characterization, and photodiode diffusion and G-R currents were investigated in an effort to develop an 8 m to 12 m infrared quantum detector using mercury cadmium telluride. Anodization, phosphorus implantation, and the graded band gap concept were approaches considered for backside formation. Variable thickness diodes were fabricated with a back surface anodic oxide to investigate the effect of this surface preparation on the diffusion limited zero bias impedance. A modeling technique was refined to thoroughly model diode characteristics. Values for the surface recombination velocity in the depletion region were obtained. These values were improved by implementing better surface damage removal techniques.

Marciniec, J. W.↗
NASA NTRS1987

Alkali Metal/Salt Thermal-Energy-Storage Systems

Proposed thermal-energy-storage system based on mixture of alkali metal and one of its halide salts; metal and salt form slurry of two immiscible melts. Use of slurry expected to prevent incrustations of solidified salts on heat-transfer surfaces that occur where salts alone used. Since incrustations impede heat transfer, system performance improved. In system, charging heat-exchanger surface immersed in lower liquid, rich in halide-salt, phase-charge material. Discharging heat exchanger surface immersed in upper liquid, rich in alkali metal.

Phillips, Wayne W.↗
NASA NTRS2017

Reconfigurable Wideband Circularly Polarized Stacked Square Patch Antenna for Cognitive Radios

An almost square patch, a square patch and a stacked square patch with corner truncation for circular polarization (CP) are researched and developed at X-band for cognitive radios. Experimental results indicate, first, that the impedance bandwidth of a CP almost square patch fed from the edge by a 50 ohm line is 1.70% and second, that of a CP square patch fed from the ground plane side by a surface launch connector is 1.87%. Third, the impedance bandwidth of a CP stacked square patch fed by a surface launch connector is 2.22%. The measured center frequency for the CP square patch fed by a surface launch connector without and with an identical stacked patch is 8.45 and 8.1017 GHz, respectively. By stacking a patch, separated by a fixed air gap of 0.254 mm, the center frequency is observed to shift by as much as 348.3 MHz. The shift in center frequency, brought about by the reconfiguring of the physical layer antenna, can be exploited in a cognitive system since it expands the usable frequency spectrum for software reconfiguration in the presence of interference. In addition, varying the fixed air gap in the stacked antenna geometry by increments of 0.254 mm further expands the usable frequency spectrum.

Cognitive↗
NASA NTRS1992

Electromagnetic scattering by coated convex surfaces and wedges simulated by approximate boundary conditions

Asymptotic/high-frequency solutions are developed for analyzing the non-specular scattering mechanisms associated with coated convex surfaces and edges simulated by approximate boundary conditions. In particular, the standard impedance boundary conditions (SIBC's) and the second order generalized impedance boundary conditions (GIBC's) are employed for a characterization of the edge diffraction, creeping wave, and surface diffracted wave contributions. To study the creeping wave and surface diffracted wave mechanisms, rigorous UTD (uniform geometrical theory of diffraction) diffraction coefficients are developed for a convex coated cylinder simulated with SIBC's and GIBC's. The ray solutions obtained remain valid in the transition region and reduce uniformly to those in the deep lit and shadow regions. A uniform asymptotic solution is also presented for observations in the close vicinity of the cylinder. The diffraction coefficient for a convex cylinder are obtained via a generalization of the corresponding ones of the circular cylinder. To validate the asymptotic/high-frequency solution, integral equations are derived for both E and H-polarization and solved numerically using the method of moments. Results are presented for a single and three layered coated convex cylinder. Some insights are also provided on the accuracy of the employed GIBC's versus SIBC's for application to curved surfaces. To characterize the scattering by impedance wedges illuminated at skew incidence, diffraction coefficients are derived from an approximate solution of the governing functional difference equations. This solution exactly recovers the known ones for an impedance half plane or an arbitrary wedge at normal incidence, and to validate it for other wedge angles, a moment method code was used. Finally, to test the usefulness of the approximate skew incidence impedance wedge diffraction coefficient for three dimensional structures, equivalent currents are derived in the context of the physical theory of diffraction (PTD) for a finite length impedance wedge of arbitrary internal angles. These are incorporated in a standard general purpose PTD code and results are presented for a number of different impedance structures.

Syed, H. H.↗
NASA NTRS2014

Acoustics of Jet Surface Interaction-Scrubbing Noise

Concepts envisioned for the future of civil air transport consist of unconventional propulsion systems in the close proximity of the structure or embedded in the airframe. While such integrated systems are intended to shield noise from community, they also introduce new sources of sound. Sound generation due to interaction of a jet flow past a nearby solid surface is investigated here using the generalized acoustic analogy theory. The analysis applies to the boundary layer noise generated at and near a wall, and excludes the scattered noise component that is produced at the leading or the trailing edge. While compressibility effects are relatively unimportant at very low Mach numbers, frictional heat generation and thermal gradient normal to the surface could play important roles in generation and propagation of sound in high speed jets of practical interest. A general expression is given for the spectral density of the far field sound as governed by the variable density Pridmore-Brown equation. The propagation Greens function is solved numerically for a high aspect-ratio rectangular jet starting with the boundary conditions on the surface and subject to specified mean velocity and temperature profiles between the surface and the observer. It is shown the magnitude of the Greens function decreases with increasing source frequency andor jet temperature. The phase remains constant for a rigid surface, but varies with source location when subject to an impedance type boundary condition. The Greens function in the absence of the surface, and flight effect are also investigated.

Propulsion Noise↗
NASA NTRS2014

Acoustics of Jet Surface Interaction - Scrubbing Noise

Concepts envisioned for the future of civil air transport consist of unconventional propulsion systems in the close proximity to the structure or embedded in the airframe. While such integrated systems are intended to shield noise from the community, they also introduce new sources of sound. Sound generation due to interaction of a jet flow past a nearby solid surface is investigated here using the generalized acoustic analogy theory. The analysis applies to the boundary layer noise generated at and near a wall, and excludes the scattered noise component that is produced at the leading or the trailing edge. While compressibility effects are relatively unimportant at very low Mach numbers, frictional heat generation and thermal gradient normal to the surface could play important roles in generation and propagation of sound in high speed jets of practical interest. A general expression is given for the spectral density of the far field sound as governed by the variable density Pridmore-Brown equation. The propagation Green's function is solved numerically for a high aspect-ratio rectangular jet starting with the boundary conditions on the surface and subject to specified mean velocity and temperature profiles between the surface and the observer. It is shown the magnitude of the Green's function decreases with increasing source frequency and/or jet temperature. The phase remains constant for a rigid surface, but varies with source location when subject to an impedance type boundary condition. The Green's function in the absence of the surface, and flight effects are also investigated

Jet Noise↗
NASA NTRS2017

Reconfigurable Wideband Circularly Polarized Stacked Square Patch Antenna for Cognitive Radios

An almost square patch, a square patch and a stacked square patch with corner truncation for circular polarization (CP) are researched and developed at X-band for cognitive radios. Experimental results indicate, first, that the impedance bandwidth of a CP almost square patch fed from the edge by a 50 ohm line is 1.70 percent and second, that of a CP square patch fed from the ground plane side by a surface launch connector is 1.87 percent. Third, the impedance bandwidth of a CP stacked square patch fed by a surface launch connector is 2.22 percent. The measured center frequency for the CP square patch fed by a surface launch connector without and with an identical stacked patch is 8.45 and 8.1017 GHz, respectively. By stacking a patch, separated by a fixed air gap of 0.254 mm, the center frequency is observed to shift by as much as 348.3 MHz. The shift in the center frequency can be exploited to reconfigure the operating frequency by mechanically increasing the air gap. The results indicate that a tuning bandwidth of about 100 MHz can be achieved when the distance of separation between the driven patch and the stacked patch is increased from its initial setting of 0.254 to 1.016 mm.

Cognitive↗
NASA NTRSDate not supplied

On the Implementation and Further Validation of a Time Domain Boundary Element Method Broadband Impedance Boundary Condition

A time domain boundary integral equation with Burton-Miller reformulation is presented for acoustic scattering by surfaces with liners in a uniform mean flow. The Ingard-Myers impedance boundary condition is implemented using a broadband multipole impedance model and converted into time domain differential equations to augment the boundary integral equation. The coupled integral-differential equations are solved numerically by a March-On-in-Time (MOT) scheme. While the Ingard-Myers condition is known to support Kelvin-Helmholtz instability due to its use of a vortex sheet interface between the flow and the liner surface, it is found that by neglecting a second derivative term in the current time domain impedance boundary condition formulation, the instability an be effectively suppressed in computation. The proposed formulation and implementation are validated using a NASA Langley Research Center Grazing Flow Impedance Tube (GFIT) experimental dataset with satisfactory results. Moreover, a minimization procedure for finding the poles and coefficients of the broadband multiple impedance model is formulated in this paper by which, unlike the commonly used vector-fitting method, passivity of the model is ensured. Numerical tests show the proposed minimization approach is effective for modeling liners that are commonly used in aeroacoustic applications.

Time Domain Impedance Boundary Condition↗
NASA NTRS2010

Satellite Gravimetry Applied to Drought Monitoring

Near-surface wetness conditions change rapidly with the weather, which limits their usefulness as drought indicators. Deeper stores of water, including root-zone soil wetness and groundwater, portend longer-term weather trends and climate variations, thus they are well suited for quantifying droughts. However, the existing in situ networks for monitoring these variables suffer from significant discontinuities (short records and spatial undersampling), as well as the inherent human and mechanical errors associated with the soil moisture and groundwater observation. Remote sensing is a promising alternative, but standard remote sensors, which measure various wavelengths of light emitted or reflected from Earth's surface and atmosphere, can only directly detect wetness conditions within the first few centimeters of the land s surface. Such sensors include the Advanced Microwave Scanning Radiometer - Earth Observing System (AMSR-E) C-band passive microwave measurement system on the National Aeronautic and Space Administration's (NASA) Aqua satellite, and the combined active and passive L-band microwave system currently under development for NASA's planned Soil Moisture Active Passive (SMAP) satellite mission. These instruments are sensitive to water as deep as the top 2 cm and 5 cm of the soil column, respectively, with the specific depth depending on vegetation cover. Thermal infrared (TIR) imaging has been used to infer water stored in the full root zone, with limitations: auxiliary information including soil grain size is required, the TIR temperature versus soil water content curve becomes flat as wetness increases, and dense vegetation and cloud cover impede measurement. Numerical models of land surface hydrology are another potential solution, but the quality of output from such models is limited by errors in the input data and tradeoffs between model realism and computational efficiency. This chapter is divided into eight sections, the next of which describes the theory behind satellite gravimetry. Following that is a summary of the GRACE mission and how hydrological information is gleaned from its gravity products. The fourth section provides examples of hydrological science enabled by GRACE. The fifth and sixth sections list the challenging aspects of GRACE derived hydrology data and how they are being overcome, including the use of data assimilation. The seventh section describes recent progress in applying GRACE for drought monitoring, including the development of new soil moisture and drought indicator products, and that is followed by a discussion of future prospects in satellite gravimetry based drought monitoring.

Rodell, Matthew↗
NASA NTRS1984

On the long range propagation of sound over irregular terrain

The theory of sound propagation over randomly irregular, nominally plane terrain of finite impedance is discussed. The analysis is an extension of the theory of coherent scatter originally proposed by Biot for an irregular rigid surface. It combines Biot's approach, wherein the surface irregularities are modeled by a homogeneous distribution of hemispherical bosses, with more conventional analyses in which the ground is modeled as a smooth plane of finite impedance. At sufficiently low frequencies the interaction of the surface irregularities with the nearfield of a ground-based source leads to the production of surface waves, which are effective in penetrating the ground shadow zone predicted for a smooth surface of the same impedance.

Howe, M. S.↗
NASA NTRS1985

On the long range propagation of sound over irregular terrain

The theory of sound propagation over randomly irregular, nominally plane terrain of finite impedance is discussed. The analysis is an extension of the theory of coherent scatter originally proposed by Biot for an irregular rigid surface. It combines Biot's approach, wherein the surface irregularities are modeled by a homogeneous distribution of hemispherical bosses, with more conventional analyses in which the ground is modeled as a smooth plane of finite impedance. At sufficiently low frequencies the interaction of the surface irregularities with the nearfield of a ground-based source leads to the production of surface waves, which are effective in penetrating the ground shadow zone predicted for a smooth surface of the same impedance.

Howe, M. S.↗
NASA NTRS1988

Model-scale sound propagation experiment

The results of a scale model propagation experiment to investigate grazing propagation above a finite impedance boundary are reported. In the experiment, a 20 x 25 ft ground plane was installed in an anechoic chamber. Propagation tests were performed over the plywood surface of the ground plane and with the ground plane covered with felt, styrofoam, and fiberboard. Tests were performed with discrete tones in the frequency range of 10 to 15 kHz. The acoustic source and microphones varied in height above the test surface from flush to 6 in. Microphones were located in a linear array up to 18 ft from the source. A preliminary experiment using the same ground plane, but only testing the plywood and felt surfaces was performed. The results of this first experiment were encouraging, but data variability and repeatability were poor, particularly, for the felt surface, making comparisons with theoretical predictions difficult. In the main experiment the sound source, microphones, microphone positioning, data acquisition, quality of the anechoic chamber, and environmental control of the anechoic chamber were improved. High-quality, repeatable acoustic data were measured in the main experiment for all four test surfaces. Comparisons with predictions are good, but limited by uncertainties of the impedance values of the test surfaces.

Willshire, William L., Jr.↗
NASA NTRS1976

Diffraction of sound by nearly rigid barriers

The diffraction of sound by barriers with surfaces of large, but finite, acoustic impedance was analyzed. Idealized source-barrier-receiver configurations in which the barriers may be considered as semi-infinite wedges are discussed. Particular attention is given to situations in which the source and receiver are at large distances from the tip of the wedge. The expression for the acoustic pressure in this limiting case is compared with the results of Pierce's analysis of diffraction by a rigid wedge. An expression for the insertion loss of a finite impedance barrier is compared with insertion loss formulas which are used extensively in selecting or designing barriers for noise control.

Hadden, W. J., Jr.↗
NASA NTRS1991

Estimating radiated power from a conducting tethered satellite system

In anticipation of the upcoming TSS-1 experiment, theoretical calculations are made of radiated power from a conducting tethered satellite system. The radiation results from the steady motion of the system through the ionospheric plasma and it is stimulated by collection and emission of charge by the noninsulated surfaces of the tethered end connectors. A model of the current system is developed which incorporates the tether wire, satellite surfaces, and sheath currents. The radiation impedance of the current model is calculated using the previously developed theory of Barnett and Olbert (1986). The results confirm the low-frequency Alfven wave description with a predicted radiation impedance of a few tenths of an ohm in the Alven wave limit. Calculations are also made in the lower hybrid and whistler wave band. A larger impedance of about 13 ohm is found for the frequency range 5-50 kHz. By estimating the passive ion current drawn by the system a prediction of the total radiated power is also made. The result of 0.38 mW raises the question of whether or not wave emissions from a passive current collecting system may be detectable by either ground- or space-based platforms.

Donohue, D. J.↗
NASA NTRS1993

Transition operators in electromagnetic-wave diffraction theory. II - Applications to optics

The theory developed by Hahne (1992) for the diffraction of time-harmonic electromagnetic waves from fixed obstacles is briefly summarized and extended. Applications of the theory are considered which comprise, first, a spherical harmonic expansion of the so-called radiation impedance operator in the theory, for a spherical surface, and second, a reconsideration of familiar short-wavelength approximation from the new standpoint, including a derivation of the so-called physical optics method on the basis of quasi-planar approximation to the radiation impedance operator, augmented by the method of stationary phase. The latter includes a rederivation of the geometrical optics approximation for the complete Green's function for the electromagnetic field in the presence of a smooth- and a convex-surfaced perfectly electrically conductive obstacle.

Hahne, G. E.↗
NASA NTRS1993

A monochromatic gravity wave observed by the Flatland Atmospheric Observatory

On 21 December 1991 from approximately 1300 to approximately 1600 UTC a monochromatic wave train with an 8.2-min period was observed by the suite of instruments at the Flatland Atmospheric Observatory (FAO), located in very flat terrain near Champaign-Urbana, Illinois. A 915-MHz radar measured the vertical wind velocity w every 60 s from 0.55 km MSL (0.34 km AGL) to approximately 3 km with 250-m range gates, and a 50-MHz radar measured the oblique wind in four directions, as well as w, every 130 s from 2.75 to approximately 7.25 km with 750-m range gates. A meteorological ground station measured the surface pressure P, wind speed vector u and azimuth alpha, temperature, solar insolation, etc., every 30 s. P was also measured every 120 s by six digital barograph stations within 30 km of Flatland. Using the hodograph of surface vector u and alpha and the impedance relation, we estimated the azimuthal direction of propagation phi to be 45 deg +/- 15 deg clockwise from north, the intrinsic and apparent horizontal phase speeds C(sub i) and C(sub o), respectively, (which are about equal since the direction of propagation is about normal to the mean wind) to be 21 +/- 5 m/s, and the horizontal wavelength lambda to be 10.0 +/- 2.5 km. The peak-to-peak surface horizontal perturbation velocity varied from approximately 2 to 5 m/s from cycle to cycle.

Vanzandt, T. E.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-33433-DND

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for aircraft noise reduction, and are characterized by a complex valued frequency-dependent impedance. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic scattering of geometric bodies treated with acoustic liners. This work considers using either an impedance boundary condition or admittance boundary condition to allow acoustic scattering problems to be modeled with geometries consisting of both un-lined and lined surfaces; admittance is defined to be the inverse of impedance. Three different acoustic liner models will be discussed: the Extended Helmholtz Resonator Model, the Three-Parameter Impedance Model, and a Broadband Model. In the Extended Helmholtz Resonator Model and Three-Parameter Impedance Model, the liner impedance is specified at a single frequency; the Broadband Model allows for the investigation of multiple frequencies simultaneously. The impedance and admittance boundary conditions for each model will be derived and coupled with a time-domain boundary integral equation. The scattering solution will be obtained iteratively using spatial and temporal basis functions. Stability will be demonstrated through eigenvalue analysis. Moreover, fast algorithms and high performance computing are considered to both assess and reduce the computational cost of the simulation.

Michelle E Rodio↗