Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Carbon Dioxide Pressure and Catalyst Quantity Dependencies in Artificial Photosynthesis of Hydrocarbon Chains on Nanostructured Co/CoO Surfaces

In this study, we investigated the influence of pressure and the quantity of Co/CoO catalyst on an artificial photosynthesis process that converts CO 2 and H 2 O into hydrocarbons (C n H 2n+2 , where n ≤ 18). The adsorption of CO 2 and H 2 O on Co/CoO surfaces proved to be pivotal in this photo-catalytic reaction. Photoexcited carbon dioxide and water molecules ((CO 2 )* and (H 2 O)*) generated by illuminating the catalyst surface led to the formation of alkene hydrocarbon molecules with carbon numbers following an approximate Poisson distribution. The optimal pressure was found to be 0.40 MPa. Pressure less than 0.40 MPa resulted in low CO 2 adsorption, impeding excitation for photosynthesis. At greater pressure, oil/wax accumulation on Co/CoO surfaces hindered CO 2 adsorption, limiting further photosynthesis reactions. The average number of carbon atoms in the hydrocarbons and hydrocarbon yield were correlated. The amount of Co/CoO was also found to affect the hydrocarbon yield. Our study contributes to the understanding of Co/CoO-catalyzed photosynthesis and suggests that an open-flow system could potentially enhance the productivity of long-chain hydrocarbons.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Tritium Transport Phenomena in Molten-Salt Reactors: Molten Salt Tritium Transport Experiment Design

Tritium is produced from neutron interactions with both lithium and beryllium. Large quantities of tritium are generated in Molten Salt Reactors (MSRs) which use LiF/BeF2 (FLiBe) as the fuel salt. Tritium is unique among the radionuclide hazards as it readily permeates through metal structural materials at high temperatures. All metal surfaces are potential release paths for tritium. For adequate safety analysis and eventual licensing of new reactors, predictive models for tritium transport and release from MSRs must be developed. These models must account for the multiple transport phenomena involved with tritium: fuel salt phase mass transport, dissociation/recombination reactions on metal surfaces, interstitial diffusion through the metal structure, and salt or gas phase mass transport in the downstream fluid. These models also must also be validated with representative experiments. Our previous report outlined tritium transport phenomena involved in MSRs, made suggestions on gaps in the transport dataset, and proposed an experimental test stand to test combined transport effects – tritium transport through pipe walls in a convective salt flow. In this report, we summarize an updated analysis framework for tritium transport in MSRs, report our results on hydrogen and deuterium permeation through Hastelloy N, and describe the final design of the Molten Salt Tritium Transport Experiment (MSTTE, pronounced “misty”). The MSRE provides the only wholistic experimental data set for tritium transport in MSRs and understanding the transport phenomena involved in the MSRE is crucial for future model development. One set of parameters in our analysis framework was unknown for the MSRE—surface reaction rates for tritium on Hastelloy N. This warranted our hydrogen and deuterium permeation campaign to assess the permeability, diffusivity, and solubility of hydrogen isotopes in clean Hastelloy N. Surface reaction rate constants were probed by low pressure measurements, however, no surface effects were observed in the limits of our permeation apparatus. Permeation experiments on oxidized Hastelloy N were not performed for this report but are planned in future work. The experimental test stand, MSTTE, measures combined transport properties of the salt-metal system. MSTTE is a forced convection FLiBe loop with custom designed test section to measure tritium transport through candidate structural materials. We use MSRE relevant dimensionless numbers to design and scale the test section. Hastelloy N is a candidate loop and test section material due to the relevance for the MSRE and related designs, however, other metals are being considered (e.g. 316H SS) which may better align with current vendor concepts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Nature of molybdenum carbide surfaces for catalytic hydrogen dissociation using machine-learned potentials: an ensemble-averaged perspective

Molybdenum carbides with an electronic structure similar to noble metals have gained attention as a promising low-cost catalyst for biomass valorization and the hydrogen evolution reaction. However, our fundamental understanding of the catalyst surface and how different phases of these catalysts behave at varying reaction conditions is limited to ground state density functional theory calculations as ab initio molecular dynamics (AIMD) is computationally prohibitive at relevant length and time scales. Here, in this work, we train a multi-atomic cluster expansion (MACE) machine-learned interatomic potentials (MLIP) to study hydrogen dissociation and dynamics over Mo, δ-MoC, α-Mo 2 C, and β-Mo 2 C surfaces at varying temperatures and hydrogen partial pressures. Our simulations identify unique and different molecular and atomic hydrogen adsorption sites on different surfaces that do not depend on the temperature. At low hydrogen pressures, the surface coverage is monolayer, which transitions to two-layer adsorption at higher pressures. We find that atomic hydrogen diffusion and recombinations are preferred over molybdenum atom hollow sites, while the diffusion over carbon-terminated facets was negligible, signifying particularly strong C–H interactions. In contrast, molecular hydrogen adsorption occurs mostly atop Mo or the bridging sites. At a comparable hydrogen loading, β-Mo 2 C (001) is the most active surface for hydrogen dissociation reaction. This work provides insights into the dynamic nature of the hydrogen dissociation chemistry and the diversity of hydrogen adsorption sites on molybdenum carbides.

08 HYDROGEN↗
DOE OSTI2023

Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part II: The Effect of Roughness on the Performance of a High-Pressure Turbine Blade

Abstract Turbine blades generally present surface roughness introduced in the manufacturing process or caused by in-service degradation, which can have a significant impact on aero-thermal performance. A better understanding of the fundamental physical mechanisms arising from the interaction between the roughness and the turbine flow at engine-relevant conditions can provide insights for the design of blades with improved efficiency and longer operational life. To this end, a high-fidelity numerical framework combining a well-validated solver for direct numerical simulation and a second-order accurate immersed boundary method is employed to predict roughness-induced aero-thermal effects on an LS89 high-pressure turbine (HPT) blade at engine-relevant conditions. Different amplitudes and distributions of surface roughness are investigated and a reference smooth-blade simulation under the same flow conditions is conducted for comparison. Roughness of increasing amplitude progressively shifts the blade suction side boundary layer transition upstream, producing larger values of the turbulent kinetic energy and higher total wake losses. The on-surface data-capturing capabilities of the numerical framework provide direct measurements of the heat flux and the skin friction coefficient, hence offering quantitative information between the surface topology and engineering-relevant performance parameters. This work may provide a benchmark for future numerical studies of turbomachinery flows with roughness.

Engineering↗
DOE OSTI2022

Computing the viscous effect in early-time drop impact dynamics

The impact of a liquid drop on a solid surface involves many intertwined physical effects, and is influenced by drop velocity, surface tension, ambient pressure and liquid viscosity, among others. Experiments by Kolinski et al. ( Phys. Rev. Lett. , vol. 112, no. 13, 2014 b , p. 134501) show that the liquid–air interface begins to deviate away from the solid surface even before contact. They found that the lift-off of the interface starts at a critical time that scales with the square root of the kinematic viscosity of the liquid. To understand this, we study the approach of a liquid drop towards a solid surface in the presence of an intervening gas layer. We take a numerical approach to solve the Navier–Stokes equations for the liquid, coupled to the compressible lubrication equations for the gas, in two dimensions. With this approach, we recover the experimentally captured early time effect of liquid viscosity on the drop impact, but our results show that lift-off time and liquid kinematic viscosity have a more complex dependence than the square-root scaling relationship. We also predict the effect of interfacial tension at the liquid–gas interface on the drop impact, showing that it mediates the lift-off behaviour.

42 ENGINEERING↗
DOE OSTI2023

A Deep Potential model for liquid–vapor equilibrium and cavitation rates of water

Computational studies of liquid water and its phase transition into vapor have traditionally been performed using classical water models. Here, we utilize the Deep Potential methodology—a machine learning approach—to study this ubiquitous phase transition, starting from the phase diagram in the liquid–vapor coexistence regime. The machine learning model is trained on ab initio energies and forces based on the SCAN density functional, which has been previously shown to reproduce solid phases and other properties of water. Here, we compute the surface tension, saturation pressure, and enthalpy of vaporization for a range of temperatures spanning from 300 to 600 K and evaluate the Deep Potential model performance against experimental results and the semiempirical TIP4P/2005 classical model. Moreover, by employing the seeding technique, we evaluate the free energy barrier and nucleation rate at negative pressures for the isotherm of 296.4 K. Further, we find that the nucleation rates obtained from the Deep Potential model deviate from those computed for the TIP4P/2005 water model due to an underestimation in the surface tension from the Deep Potential model. From analysis of the seeding simulations, we also evaluate the Tolman length for the Deep Potential water model, which is (0.091 ± 0.008) nm at 296.4 K. Finally, we identify that water molecules display a preferential orientation in the liquid–vapor interface, in which H atoms tend to point toward the vapor phase to maximize the enthalpic gain of interfacial molecules. We find that this behavior is more pronounced for planar interfaces than for the curved interfaces in bubbles. This work represents the first application of Deep Potential models to the study of liquid–vapor coexistence and water cavitation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Phase-field simulations of fission gas bubbles in high burnup UO2 during steady-state and LOCA transient conditions

To improve the economics of commercial nuclear energy generation, U.S. utilities are currently seeking licensing approval to operate UO2 fuel to higher burnups. One significant safety issue that must be addressed to obtain approval is the potential for fine fragmentation/pulverization of the fuel during a loss-of-coolant accident (LOCA). It has been hypothesized this is caused by the rapid increase of pressure in fission gas bubbles in the high burnup region of the fuel. To better understand this phenomenon, a novel phase-field model of the fission gas bubble microstructure in UO2 has been developed and implemented in Idaho National Laboratory's Marmot application for phase-field simulation of nuclear materials. Simulations of bubble growth in the high burnup region during steady-state conditions showed that initially overpressurized bubbles decreased in pressure during growth, but still remained above equilibrium pressure. During a LOCA transient, simulations of bubbles in the high burnup region showed that bubble size did not change significantly, and the pressure increase due to the transient was calculated and passed to a phase-field model of fracture.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Robust In-Situ Strain Measurements to Monitor CO 2 Storage

The goal of this project was to develop and demonstrate robust instrumentation to monitor the in-situ strain tensor in order to improve the reliability and security of CO 2 storage in geologic formations. We met the original goals of the project and the major overarching accomplishment is the advancement of strain tensor monitoring from an intriguing concept to a commercially available technology with a solid foundation of novel instruments supported by theoretical analyses and validation experiments. The main accomplishments of the project are summarized below. We designed, built and evaluated nine new optical fiber strainmeters and tiltmeters using Michelson interferometers to measure deformation with ultra-high resolution at both shallow and deep point locations in the subsurface. These are the robust strainmeters that motivated the title of the project. We designed, built and evaluated a novel method of measuring distributed strain in optical fibers with nanostrain resolution, and cm-scale location, and sampling into the seismic band. The new method is called Coherence-length-gated Microwave Photonics Interfereometry (CMPI). CMPI technology has advantages over existing commercial DAS and DSS methods. We developed and demonstrated capabilities to deploy instruments in the field and used them to measure strain caused by ambient signals like barometric pressure and tides, as well as induced signals like surface loading and pore pressure changes from pumping tests. We deployed a working strainmeter at 1,700 ft depth, slightly above an active reservoir. This is to our knowledge the greatest depth a strainmeter has been deployed and the techniques we used can readily be extended to greater depths. Optical fiber borehole tensor strainmeter techology was advanced from a TRL 4 at the start, to a TRL of 7 at the conclusion of the project. The project included advances in simulations and theoretical analyses. We developed and demonstrated a computational workflow that uses machine learning to reduce the computational requirements and make it practical to use Bayesian inversion to solve large numerical poroelastic analyses needed to interpret strain tensor field data. We evaluated the strain tensor fields and time series that would be caused by leaks of CO 2 or other fluids from reservoirs. These simulations demonstrated that signals from leaks could be measured with instruments developed for the project, opening a potentially new method for ensuring storage security. We showed that strains in caprock can be used to estimate pressure in a reservoir. This avoids the need to drill monitoring wells into the reservoir, and it expands the capabilities of monitoring in the caprock. The project includes a derivation and application of a novel analytical solution to the strains in the vicinity of a pressurized poroelastic inclusion. This solution explains field data measured during injeciton tests at the North Avant Field, and it will simplify future interpretation of strain tensor data. The project included a broad range of experiments, and of the most significant is the characterization of the strain tensor at an array three strainmeters during six injection tests at the North Avant Field, Oklahoma. This demonstrated repeatability of the strain signal measured by the new instruments developed for the project, and it showed similarities between the strain signal at shallow depths and pressure in the underlying reservoir. We also demonstrated that useful strain data can be measured at reservoir depths. This confirms that strain tensor data can be measured throughout the caprock over a reservoir. The project demonstrated the feasibility of using the strain tensor and distributed strain measured in caprock during a variety of different well tests where the pumping rate was constant, sinusoidal and positive, or a periodic square wave with zero net rate. This further strengthens the validity of using strain data to characterize reservoirs and aquifers. We also demonstrated that strain caused be fluctuations of air pressure and water pressure in the vadose zone can be measured and interpreted, suggesting that high resolution distributed strain measurements hold promise for monitoring the vadose zone. The project partially supported nine graduate students in the Environmental Engineering, Hydrogeology, Electrical Engineering programs at Clemson University. The research was described in nine journal papers, 23 talks and conference abstracts. Additional journal papers are in preparation. A new company called Tensora was started to provide strainmeter technology for commercial applications.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Charged particle dynamics near an X-point of a non-symmetric magnetic field with closed field lines

Understanding particle drifts in a non-symmetric magnetic field is of primary interest in designing optimized stellarators in order to minimize the neoclassical radial loss of particles. Quasisymmetry and omnigeneity, two distinct properties proposed to ensure radial localization of collisionless trapped particles in stellarators, have been explored almost exclusively for magnetic fields with nested flux surfaces. In this work, we examine radial particle confinement when all field lines are closed. We then study charged particle dynamics in the special case of a non-symmetric vacuum magnetic field with closed field lines obtained recently by Weitzner & Sengupta ( Phys. Plasmas , vol. 27, 2020, 022509). These magnetic fields can be used to construct magnetohydrodynamic equilibria for low pressure. Expanding in the amplitude of the non-symmetric fields, we explicitly evaluate the omnigeneity and quasisymmetry constraints. We show that the magnetic field is omnigeneous in the sense that the drift surfaces coincide with the pressure surfaces. However, it is not quasisymmetric according to the standard definitions.

Physics↗
DOE OSTI2021

Particle emission with identification from an atmospheric pressure plasma liquid interface

A conspicuous emission phenomenon of luminous particles from the liquid anode surface of an atmospheric pressure DC glow discharge is reported. The emission has been shown to occur when the plasma forms a pattern on the surface of the liquid electrolyte. Here, the spatial-temporal evolutions of the trajectories of emitted particles were studied using a high-speed imaging system. Particles were sampled in flight using a witness plate for analysis. Critical particle characteristics were examined using electron microscope technologies. The morphology of the resulting splats and compositions suggest that they are molten droplets with a great deal of structure, including evidence of nanoprecipitation. A theoretical model was employed to estimate the particle size from the measured splats, which provides a radius range within a hundred micrometers. This experiment leads to the postulation of a mechanism in which particle emission at the plasma liquid interface is likely driven by the Taylor cone effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Drizzle, Turbulence, and Density Currents Below Post Cold Frontal Open Cellular Marine Stratocumulus Clouds

Nine cases of postcold frontal marine stratocumulus clouds exhibiting open cellular mesoscale organization are analyzed to characterize the drizzle, turbulence, and density currents below them. Data collected by the vertically pointing Doppler cloud radar and multiple lidars part of the Atmospheric Radiation Measurement (ARM) Eastern North Atlantic (ENA) site are used in these analyses. A total of 251 drizzle shafts passed over the site with 76 shafts sampled for more than 15 min by the vertically pointing instruments. On average the drizzle shafts were ~18 km wide with below-cloud drizzle water path of ~40 g m −2 , cloud base rain rate of 7.78 mm day −1 , and cloud base drizzle modal diameter of 393 μm. The widths of the drizzle shafts did not exhibit any relationship with the cloud base rain rate, below-cloud drizzle water path, and the total water removed from the cloud. The downdrafts in the lowest 500 m within the drizzle cells strengthened with increasing cloud base rain rates, while the updrafts within drizzle cells did not exhibit this behavior. On average, the surface air density, pressure, water vapor mixing ratio, and wind speed along the background wind during the drizzle shaft were higher by 1.88 g m −3 , 8.60 Pa, 0.24 g kg −1 , and 1.22 m s −1 , respectively, from their background values. On the other hand, the surface air temperature was lower by 0.43 K during the drizzle shaft than its background value. The coincident measurements highlight the drizzle-turbulence-surface coupling in these cloud systems.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Chromium-coated cladding analysis under simulated LOCA burst conditions

Of the near-term accident-tolerant fuel concepts identified, chromium coatings have been shown to slow cladding oxidation without altering fuel system geometry or greatly affecting neutronic performance. To identify how coated cladding tubes perform under high-temperature accident conditions, pressurized-tube burst tests were conducted in the Severe Accident Test Station at Oak Ridge National Laboratory. To analyze how the coating affects cladding behavior, coated and uncoated cladding burst tests were simulated by using the BISON fuel performance code. Thermocouple data from these tests were fit into axial and azimuthal profiles and combined to generate 3D cladding surface temperatures, and pressure transducer data were compared until cladding failure. Additionally, the cladding temperatures at failure and the internal gas pressure evolution show relatively good agreement between the simulation and experiment results. Simulations were then extrapolated to demonstrate the coatings effectiveness to increasing the cladding burst temperature by using a parametric evaluation of the initial tube gas pressure. This work demonstrates the possibility of an increased cladding failure margin under transient conditions due to the addition of chromium coating, and more pertinently, an increased cladding failure margin from more accurate experimental characterization.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Experimental Investigation of Innovative Cooling Schemes on an Additively Manufactured Engine Scale Turbine Nozzle Guide Vane

This study includes the design, validation, and fabrication via direct metal laser sintering (DMLS) of a gas turbine nozzle guide vanes (NGV) that incorporates three innovative cooling schemes specifically enabled by additive manufacturing. The novel NGV design is the culmination of an extensive research and development effort over a period of 4 years that included low- and high-speed cascade testing coupled with unsteady computational fluid dynamics for numerous candidate innovative cooling architectures. The final vane design (SJ-vane) consists of sweeping jet (SJ) film cooling holes on the suction surface (SS), sweeping jet impingement holes at the leading edge and double-wall partial length triangular pin-fin with impinging jet at the trailing edge. For comparison purposes, a second DMLS enabled vane (777-vane) was designed and fabricated with prototypical cooling circuits to serve as a baseline. This vane consists of a shaped film cooling holes on the suction surface, circular impingement holes at the leading edge, and full-length cylindrical pin-fins at the trailing edge. Experiments with the two DMLS enabled vanes were performed at the Ohio State University Turbine Reacting Flow Rig (TuRFR) at engine-relevant temperature (1375 K) and Mach number conditions. Infrared (IR) thermography was utilized to measure the wall temperature of the pressure and suction surface at several coolant mass flowrates to estimate the overall cooling effectiveness (ϕ). Results showed improved cooling performance for the advanced cooling schemes (sweeping jet film cooling, impingement cooling, and triangular pin-fin cooling) compared with the baseline cooling schemes.

Engineering↗
DOE OSTI2025

The Surface Chemistry of Methanol on TiO 2 (110): Effects of Pressure and Temperature on the Stability of C–O and C–H Bonds

Synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS) was used to study the surface chemistry of methanol on TiO 2 (110), examining the effects of methanol pressure, oxide temperature, and coadsorption with H 2 . At 300 K, the adsorption of methanol on TiO 2 (110) leads to the formation of CH 3 O on the surface with a minor amount of CH 3 OH present. The easy cleavage of the O–H bond in the alcohol agrees with the predictions of theoretical calculations, and most of the adsorbed CH 3 O was not associated with the presence of Ti 3+ sites in the oxide substrate. The adsorbed CH 3 O was removed from the TiO 2 (110) surface by heating to 600 K without the deposition of CH x fragments or C on the oxide. The results of temperature-programmed desorption (TPD) showed the evolution of methanol and formaldehyde at 360 and 490 K as a result of a disproportionation reaction: 2CH 3 O → CH 3 OH + CH 2 O. This surface chemistry, where there is no rupture of the C–O bond, and only selective cleavage of O–H and C–H bonds, is very different from that found on metals used in catalysts for methanol reforming, where massive conversion of the alcohol into CO, CH x and C species is seen. Furthermore, the TPD data indicate that any CH 3 O formed on the oxide surface can be hydrogenated and desorbed as CH 3 OH at temperatures below 550 K. In this respect, titania is an ideal support for catalysts employed to achieve methanol synthesis through CO 2 hydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Heat Transfer Experiments of a 1st Stage Blade Cascade for Supercritical CO2 Oxy-Combustion Turbine Application

The results of internally cooled 1st stage blade (S1B) cascade testing in a supercritical CO2 environment is presented. The turbine blade design has been previously established for the end application of an oxy-combustion turbine operating in the Allam-Fetvedt cycle with turbine inlet conditions of 305 bar and 1150°C. The internally cooled blade features leading edge (LE) region impingement cooling, mid-section ribbed serpentine passages, and a pin-finned trailing edge (TE) region before cooling ejection holes. The geometry for the tested blade cascade has a cooled central blade with un-cooled blades on either side to match flowpath areas of the actual turbine. The flowpath reuses internal components previously employed for mid-section region ribbed serpentine passage experiments that established Nusselt number enhancement ratios over a range of Reynolds numbers from 100,000-400,000. New components include flow conditioning plates upstream and downstream of the blade cascade to adequately represent the flow field and blade external heat transfer coefficient profiles for the actual turbine. The cooled central blade utilizes uniform crystal temperature sensors (UCTS) with six sensors each on the blade pressure and suction surfaces distributed radially and from LE to TE. The post-processed UCTS quantified the maximum wall temperature seen at each installed sensor location. The test procedure consisted of establishing supercritical CO2 cooling flow temperature and flow rate and maintaining it throughout the test. The flow rate aims to match that for the actual in-service turbine blade design and is maintained through an orifice restriction to keep the pressure differential between internal cooling flow and external hot flow nearly constant. For the sCO2 flow path external to the blade, temperatures were ramped throughout the test via control of the test loop’s natural gas burner heater. The maximum temperature seen was 468°C and held constant for a duration of 10 minutes at which the blade metal temperature was predicted to be at its maximum before ramping down. For the turbine blade design for service inlet conditions, external flow path computational fluid dynamics (CFD) results and an internal cooling 1-D thermal and hydraulic flow network model using experimentally validated correlations served as thermal finite element (FE) boundary conditions to predict blade metal temperatures. These predicted temperatures were subsequently utilized in a structural FE model to predict blade life ratings dictated by Haynes 282 creep strength data, having a strong dependence on temperature. The boundary conditions experienced during testing are used in the same workflow and compared to the experimental results, with the goal of validating the analysis methodology and providing insight on the uncertainty in local metal temperature predictions.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Probing the Surface Chemistry of Lithium Nitridation

Chemical synthesis of Li 3 N through lithium nitridation has potential to advance rechargeable battery and nitrogen fixation technology. However, studies of the conditions for forming Li 3 N on the lithium surface via nitrogen gas exposure report contradictory findings, such as the spontaneous reaction of Li with pure N 2 , the impossibility of forming Li 3 N through pure Li and N 2 interaction, the requirement of trace H 2 O to catalyze the reaction, and evidence to the contrary. In this study, ambient pressure X-ray photoelectron spectroscopy (APXPS) was applied to evaluate the in situ chemical evolution of the lithium metal surface under nitrogen gas up to 800 mTorr. At pressures ≤10 mTorr, no Li 3 N was detected. At higher pressures, surface Li 3 N rapidly reacts with trace CO 2 . Additionally, because metallic lithium is readily oxidized by trace gases, the atomic nitrogen concentration of the lithium surface remains below 2%. When nitridation follows oxidation by O 2 gas, CO 2 gas, or H 2 O vapor, surface Li 3 N formation is inhibited. These results suggest that nitrogen gas can diffuse through the oxidized lithium metal surface to react with subsurface metallic lithium.

Binding energy↗
DOE OSTI2024

Ionic Liquids as Extreme Pressure Additives for Bearing Steel Applications

The protection of steel surfaces from wear under extreme pressure conditions is of major importance in several industries as it provides better performance and longer life of machinery. The motivation for this work was to study the lubrication of steel by ionic liquids (ILs), which have recently emerged as greener alternatives to commercial lubricants and additives. Three ILs based on sulfur-containing anions, used as 2-wt% additives in polyethylene glycol base oil (MW 200; PEG 200), were tested in the lubrication of ASTM 52100 bearing steel contacts in extreme pressure conditions (under mixed lubrication with a Hertzian pressure of 1.12 GPa) using a mini traction machine (MTM). Due to the poor resistance to corrosion of bearing steel, a semi-ester of succinic acid derivative corrosion inhibitor (Lanxess RC 4801) was added to the mixtures at a 1 wt% concentration. The ILs 1-hexyl-methylimidazolium trifluoromethanesulfonate ([C 6 mim][TfO]) and 1-hexyl-4-picolinium trifluoromethanesulfonate ([C 6 -4-pic][TfO]) revealed promising results in terms of surface protection of bearing steel. In contrast, 4-picolinium hydrogen sulfate ([4-picH][HSO 4 ]) as 2-wt% additive to PEG 200 + 1% RC 4801 did not show any improvement in wear performance compared to neat PEG 200 + 1% RC 4801. PEG 200 + 2% [C 6 mim][TfO] + 1%RC 4801 allowed for a decrease in wear up to ~ 76% and PEG 200 + 2% [C 6 -4-pic][TfO] + 1%RC 4801 up to ~ 46% when compared with neat PEG 200 + 1% RC 4801. Optical microscopy images suggest the formation of an adsorbed layer, which was further supported by chemical analysis via x-ray photoelectron spectroscopy (XPS) data for [C6mim][TfO].

friction↗