Search NASA⌕ Search

SEARCH · Search NASA

Results for “system optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Optimized System Identification

In system identification, one usually cares most about finding a model whose outputs are as close as possible to the true system outputs when the same input is applied to both. However, most system identification algorithms do not minimize this output error. Often they minimize model equation error instead, as in typical least-squares fits using a finite-difference model, and it is seen here that this distinction is significant. Here, we develop a set of system identification algorithms that minimize output error for multi-input/multi-output and multi-input/single-output systems. This is done with sequential quadratic programming iterations on the nonlinear least-squares problems, with an eigendecomposition to handle indefinite second partials. This optimization minimizes a nonlinear function of many variables, and hence can converge to local minima. To handle this problem, we start the iterations from the OKID (Observer/Kalman Identification) algorithm result. Not only has OKID proved very effective in practice, it minimizes an output error of an observer which has the property that as the data set gets large, it converges to minimizing the criterion of interest here. Hence, it is a particularly good starting point for the nonlinear iterations here. Examples show that the methods developed here eliminate the bias that is often observed using any system identification methods of either over-estimating or under-estimating the damping of vibration modes in lightly damped structures.

Juang, Jer-Nan↗

Optimized System for On-Route Fast Charging of Battery-Electric Shuttle Buses

Electrifying cars, buses, and trucks is an attractive means of reducing energy use and emissions because it involves more efficient drivetrain components and minimal restructuring of the transportation network. Transit buses, driving fixed routes, help minimize driver range anxiety by properly sizing energy storage systems. A major challenge to fully electrifying transit buses is providing the amount of energy they consume in a day of driving. To enable a full day of operation without charging, batteries need to be large, which could be expensive and heavy. This work utilizes real-world transit bus data used in a battery-electric drivetrain model to co-optimize charger locations, charger power levels, and vehicle battery sizes.

ADVANCED PROPULSION SYSTEMS↗

Wireless Chemical Sensor Systems (Optimization of Field-Structured Chemiresistors for in situ Quantification of Propellant Stabilizer Concentration)

This project is a Cooperative Research and Development Agreement (CRADA) with International Electronic Machines Corp. (IEM, Troy, NY), who is contracted through the U.S. Naval Air Systems Command (NAVAIR) (under SBIR N111-010) to develop an in situ wireless chemical sensor system called the Stabilizer Level Accurate Measurement System (SLAMS). The SLAMS device is specified to include a miniature, very thin, self-contained chemical-sensor node to detect and track the level of stabilizer present in various PADs and CADs. IEM is focused on the wireless sensor platform, node communication, and electronics; whereas Sandia National Laboratories’ (SNL’s) efforts are focused on the chemical sensor development and integration. The sensor technology being employed is known as field-structured chemiresistors (FSCRs), which was invented by James Martin, et al. (SNL) and refined by Martin and Read. These sensors are small, require very little power, and have tunable sensitivity and selectivity. In the following, we discuss SNL’s efforts to optimize the FSCRs for the demanding chemical and environmental conditions that will be encountered in this application.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Shuttle cryogenics supply system optimization study. Volume 5, B-3, part 2: Appendix to programmers manual for math model

A computer programmer's manual for a digital computer which will permit rapid and accurate parametric analysis of current and advanced attitude control propulsion systems is presented. The concept is for a cold helium pressurized, subcritical cryogen fluid supplied, bipropellant gas-fed attitude control propulsion system. The cryogen fluids are stored as liquids under low pressure and temperature conditions. The mathematical model provides a generalized form for the procedural technique employed in setting up the analysis program.

Source record↗

Control system optimization studies. Volume 2: High frequency cutoff filter analysis

The problem of digital implementation of a cutoff filter is approached with consideration to word length, sampling rate, accuracy requirements, computing time and hardware restrictions. Computing time and hardware requirements for four possible programming forms for the linear portions of the filter are determined. Upper bounds for the steady state system output error due to quantization for digital control systems containing a digital network programmed both in the direct form and in the canonical form are derived. This is accomplished by defining a set of error equations in the z domain and then applying the final value theorem to the solution. Quantization error was found to depend upon the digital word length, sampling rate, and system time constants. The error bound developed may be used to estimate the digital word length and sampling rate required to achieve a given system specification. From the quantization error accumulation, computing time and hardware point of view, and the fact that complex poles and zeros must be realized, the canonical form of programming seems preferable.

Fong, M. H.↗

Gas Turbine Heavy Hybrid Powertrain Variants. Opportunities and Potential for Systems Optimization

Widespread use of alternative hybrid powertrains is currently inevitable, and many opportunities for substantial progress remain. Hybrid electric vehicles (HEVs) have attracted considerable attention due to their potential to reduce petroleum consumption and greenhouse gas emissions in the transportation sector. This capability is mainly attributed to (a) the potential for downsizing the engine, (b) the potential for recovering energy during braking and thus recharging the energy storage unit, and (c) the ability to minimize the operation of the engine outside of its most efficient brake specific fuel consumption (BSFC) regime. Hybridization of the Class 8, heavy-duty (HD) powertrain is inherently challenging due to the expected long-haul driving requirements and limited opportunities for regenerative braking. The objective of this project is to develop control strategies aiming at optimizing the operation of a Class 8 HEV that features a micro-turbine as the heat engine. The micro-turbine application shows promise in fuel efficiency, even when compared to current diesel engines, and can meet regulated exhaust emissions levels with no exhaust after-treatment system. Both parallel and series HEV variants will be examined to understand the merits of each approach of the micro-turbine to MD advanced powertrain applications. These powertrain configurations enable new paradigms in operational efficiency, particularly in the Class 8 truck fleet. The successful development of these HEV variants will require a thorough technical understanding of the complex interactions between various energy sources and energy consumption components, for various operating modes. PACCAR will be integrating the first generation of their series HEV powertrain with a Brayton Energy micro-turbine into a Class 8 HD truck tractor that has both regional haul and local pick-up and delivery (P&D) components to its drive cycle. The vehicle will be deployed into fleet operation for a demonstration period of six (6) months to assess real world operating benefits of the advanced powertrain. A parallel variant of the micro-turbine powertrain will be built and sent to the ORNL Vehicle Systems Integration Laboratory.

33 ADVANCED PROPULSION SYSTEMS↗

Advanced Vehicle Technology Analysis and Evaluation Activities and Heavy Vehicle Systems Optimization Program: 2009 Annual Progress Report

The prime objective of the AVTAE team activities is to evaluate VT Program targets and associated data that will enable the VT technology R&D teams to focus research on specific technology areas. The areas of interest are technologies that will maximize the potential for fuel efficiency improvements, as well as petroleum displacement, and tailpipe emissions reduction. AVTAE accomplishes this objective through a tight union of computer modeling and simulation, integrated component testing and emulation, and laboratory and field testing of vehicles and systems. AVTAE also supports the VT Program goals of fuel consumption reduction by developing and evaluating vehicle system technologies in the area of vehicle ancillary loads reduction.

33 ADVANCED PROPULSION SYSTEMS↗

Trip optimization system and method for a train

A system for operating a train having one or more locomotive consists with each locomotive consist comprising one or more locomotives, the system including a locator element to determine a location of the train, a track characterization element to provide information about a track, a sensor for measuring an operating condition of the locomotive consist, a processor operable to receive information from the locator element, the track characterizing element, and the sensor, and an algorithm embodied within the processor having access to the information to create a trip plan that optimizes performance of the locomotive consist in accordance with one or more operational criteria for the train.

42 ENGINEERING↗

Integrated floating wind farm layout design and mooring system optimization to increase annual energy production

As we cluster wind turbines in wind farms to gain energy from sites with high wind speeds, wake losses occur within the wind farm. Wake loss is a term used to describe the lower energy production of a downwind turbine that is totally or partially in the wake of an upwind turbine. To decrease wake losses inside the wind farm, the wind farm’s layout is optimized. However, a variety of factors constrain the wind farm layout optimization, such as the size of the lease area relative to the number of turbines to be placed, or the shape of the lease area. Therefore, many wind farms end up with a regular grid layout, such as the Horns Rev 1 wind farm in the North Sea. The ability of a floating offshore wind turbine (FOWT) to change its position based on the wind direction and its mooring system design presents an opportunity to further decrease wake losses in floating wind farms. In this work, we integrate the design of the FOWT mooring systems with the floating wind farm layout design with the goal of increasing the farm’s annual energy production. We use the Horns Rev 1 wind farm as a case study to demonstrate our method. The results show that allowing the FOWT to relocate can decrease wake losses up to 18%. Moreover, the newly developed mooring systems are less stiff and therefore allow larger motion of the FOWT; hence, the material cost of the mooring system decreases by an estimated 17%.

17 WIND ENERGY↗

Economic Assessment of Nuclear Hybrid Energy Systems: Optimization using RAVEN

The energy market supply is under pressure to achieve competing goals, such as minimizing the cost of electricity and greenhouse gas emissions while achieving grid resilience and reliability and meeting regulatory requirements. To study different scenarios for possible evolutions of the energy market that assume a certain renewable penetration and the possible introduction of hybrid nuclear reactors, the HYBRID modeling and simulation project has been initiated by INL. The term hybrid nuclear reactor here refers to nuclear power plants that not only produce electricity, but can also sell heat to an industrial process, like a hydrogen generation or water desalination plant. The RAVEN (Risk Analysis Virtual Environment) code developed at INL together with the modeling language Modelica (the Dymola compiler is used) have been selected as the main modeling tools for the HYBRID modeling and simulation project. This summary outlines the challenge, presents an overview of the developments in the RAVEN code needed to solve it and shows an illustrative example calculation. The HYBRID modeling and simulation project is a multi laboratory effort, involving research teams from three different U.S. national laboratories, led by the Idaho National Laboratory (INL) and supported by the Argonne National Laboratory (ANL) and the Oak Ridge National Laboratory (ORNL)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Plant-microbe genomic systems optimization for energy

The overall objective of this project was to identify genetic variation within grasses that results in increased biomass yield and biofuel conversion efficiency. Improving energy crops hinges on identifying the genetic mechanisms underlying traits that benefit energy production. The exploitation of natural variation in plant species is an ideal approach to identify both the traits and the genes of interest in the production of biofuels. The specific goals of this project were to (1) quantify relevant genetic diversity for biofuel feedstock bioconversion efficiency and biomass accumulation, (2) identify genetic loci that control these traits, and (3) characterize genes for improved energy crop systems. Determining the key genetic contributors influencing biofuel traits is required in order to determine the viability of these traits as targets for improvement; only then will we be able to apply modern breeding practices and genetic engineering for the rapid improvement of feedstocks.

09 BIOMASS FUELS↗

Highly interactive, steered scientific workflows on HPC systems: optimizing design solutions

Scientific workflows are becoming increasingly important in high performance computing (HPC) settings, as the feasibility and appeal of many simultaneous heterogeneous tasks increases with increasing hardware capabilities. Currently no HPC-based workflow platform supports a dynamically adaptable workflow with interactive steering and analysis at run-time. Furthermore, for most workflow programs, compute resources are fixed for a given instance, resulting in a possible waste of expensive allocation resources when tasks are spawned and killed. Here we describe the design and testing of a run-time-interactive, adaptable, steered workflow tool capable of executing thousands of parallel tasks without an MPI programming model, using a database management system to facilitate task management through multiple live connections. We find that on the Oak Ridge Leadership Computing Facility pre-exascale Summit supercomputer it is possible to launch and interactively steer workflows with thousands of simultaneous tasks with negligible latency. For the case of particle simulation and analysis tasks that run for minutes to hours, this paradigm offers the prospect of a robust and efficient means to perform simulation-space exploration with on-the-fly analysis and adaptation.

Ossyra, John R↗

NPIP: A skew line needle configuration optimization system for HDR brachytherapy

Purpose: In this study, the authors introduce skew line needle configurations for high dose rate (HDR) brachytherapy and needle planning by integer program (NPIP), a computational method for generating these configurations. NPIP generates needle configurations that are specific to the anatomy of the patient, avoid critical structures near the penile bulb and other healthy structures, and avoid needle collisions inside the body. Methods: NPIP consisted of three major components: a method for generating a set of candidate needles, a needle selection component that chose a candidate needle subset to be inserted, and a dose planner for verifying that the final needle configuration could meet dose objectives. NPIP was used to compute needle configurations for prostate cancer data sets from patients previously treated at our clinic. NPIP took two user-parameters: a number of candidate needles, and needle coverage radius, {delta}. The candidate needle set consisted of 5000 needles, and a range of {delta} values was used to compute different needle configurations for each patient. Dose plans were computed for each needle configuration. The number of needles generated and dosimetry were analyzed and compared to the physician implant. Results: NPIP computed at least one needle configuration for every patient that met dose objectives, avoided healthy structures and needle collisions, and used as many or fewer needles than standard practice. These needle configurations corresponded to a narrow range of {delta} values, which could be used as default values if this system is used in practice. The average end-to-end runtime for this implementation of NPIP was 286 s, but there was a wide variation from case to case. Conclusions: The authors have shown that NPIP can automatically generate skew line needle configurations with the aforementioned properties, and that given the correct input parameters, NPIP can generate needle configurations which meet dose objectives and use as many or fewer needles than the current HDR brachytherapy workflow. Combined with robot assisted brachytherapy, this system has the potential to reduce side effects associated with treatment. A physical trial should be done to test the implant feasibility of NPIP needle configurations.

60 APPLIED LIFE SCIENCES↗

Development and Commercialization of an IDAES-Based Power Plant Performance Monitoring and Optimization System

DOE and NETL have created an advanced, open-source computational platform through the Institute for the Design of Advanced Energy Systems (IDAES). The IDAES platform is a very extensive modeling environment that can be used for a broad range of power plant and process applications. MapEx Software is developing and commercializing a software application that makes it easier to set-up and run IDAES-based analyses. The MapEx-developed software application will replace the need for custom Python language coding with a user-friendly graphical user interface where the user can construct a flowsheet diagram of the IDAES model by inserting icons representing the plant equipment onto the screen. This application will make the implementation of modeling and optimization of existing fossil-fired power plants more straight-forward and less time-consuming. The effort focuses on performance monitoring and optimization of plant operations for the existing coal-fired power plant fleet but is built on a structure that allows expansion into the broad range of applications where IDAES methods may be applied.

20 FOSSIL-FUELED POWER PLANTS↗

Integration of Superconducting Magnetic Energy Storage (SMES) Systems Optimized with Second-Generation, High-Temperature Superconducting (2G-HTS) Technology with a Major Fossil-Fueled Asset

Utility companies and fossil fueled generation assets are seeking combinations of “hybrid energy storage” to allow power to be provided in advance of, and to otherwise complement, peaking natural gas-fired generation. American Maglev Technology of Florida Inc. (AMT) learned during the Phase I program based on interactions with NRG Energy (NRG) that energy storage such as superconducting magnetic energy storage (SMES) can qualify as a Black Start unit in most markets, ensuring orderly re-start of grid operations and fossil fueled power plants and serving as an important asset of hybrid energy storage technology. In conjunction with the University of Houston (UH), AMT and NRG are working together to scale up low-cost, high- efficiency, second-generation high-temperature superconducting (2G-HTS) technology for deployment across several markets, with a primary focus on the commercial development of utility grid-scale SMES (g-SMES) systems. Ultimately the program confirmed that the novel g-SMES design can meet the performance and financial requirements of the fossil power plant industry, while exhibiting continuous grid-voltage regulation; cost-effective, peak-hour energy storage with almost infinite life; increased input/output efficiency; and the capability to undergo millions of charging cycles, without degradation, representing a significant improvement over lithium ion and other conventional storage technologies. We believe wide scale deployment of this technology is feasible and practical when compared to the higher life cycle cost and relatively short lifespan of chemical batteries. Based on these findings, the future for deployment of SMES at many fossil-fueled power plants exceeding 100MW capability is bright. Further de-risking g-SMES technology would pave the way for the construction of a subscale prototype. Eventually, scaled-down versions of SMES are expected to be competitive with the multi-billion-dollar lithium-ion market for a wide range of commercial, industrial, and transportation uses. There is long-term potential for commercialization and widespread deployment of this disruptive technology, which would spawn a new worldwide supply chain and create domestic, high-tech manufacturing jobs in the green industry.

20 FOSSIL-FUELED POWER PLANTS↗