Search NASA⌕ Search

SEARCH · Search NASA

Results for “technology translation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Software reengineering

Today's software systems generally use obsolete technology, are not integrated properly with other software systems, and are difficult and costly to maintain. The discipline of reverse engineering is becoming prominent as organizations try to move their systems up to more modern and maintainable technology in a cost effective manner. JSC created a significant set of tools to develop and maintain FORTRAN and C code during development of the Space Shuttle. This tool set forms the basis for an integrated environment to re-engineer existing code into modern software engineering structures which are then easier and less costly to maintain and which allow a fairly straightforward translation into other target languages. The environment will support these structures and practices even in areas where the language definition and compilers do not enforce good software engineering. The knowledge and data captured using the reverse engineering tools is passed to standard forward engineering tools to redesign or perform major upgrades to software systems in a much more cost effective manner than using older technologies. A beta vision of the environment was released in Mar. 1991. The commercial potential for such re-engineering tools is very great. CASE TRENDS magazine reported it to be the primary concern of over four hundred of the top MIS executives.

Fridge, Ernest M., III↗

A broadband RF continuously variable time delay device

A method for implementation of continuously variable time delay of broadband RF signals is described. The method uses Bragg Cell and optical heterodyne technology. The signal to be delayed is applied to the Bragg Cell acoustic transducer, and the delay time is the acoustic transit time from this transducer to the incident light beam. By translating the light beam, the delay is varied. Expressions describing the Bragg Cell diffraction, lens Fourier transformation, and the optical heterodyne processes are developed. Specifications for the variable delay including bandwidth, range of delay, and insertion loss are provided. Applications include radar signal processing, spread spectrum intercept, radar ECM, and adaptive array antenna processing.

Freyre, F. W.↗

A Subsurface Explorer for Deep Underground Exploration on Mars

A subsurface explorer (SSX) is being developed at the Jet Propulsion Laboratory which is suitable for exploration of the deep underground environments on Mars. The device is a self-contained piledriver which uses a novel 'spinning hammer' technology to convert a small continuous power feed from the surface over a two-wire tether into a large rotational energy of a spinning mass. The rotational energy is converted to translational energy by a novel mechanism described here. The hammer blows propagate as shock waves through a nosepiece, pulverizing the medium ahead of the SSX. A small portion of the pulverized medium is returned to the surface through a hole liner extending behind the SSX. This tube is 'cast in place' from two chemical feedstocks which come down from the surface through passages in the hole liner and which are reacted together to produce new material with which to produce the hole liner. The lined hole does not need to be the full diameter of the SSX: approximately 100 kilograms of liner material can create a tunnel liner with a three millimeter inside diameter and a six millimeter outside diameter with at total length of four kilometers. Thus it is expected that core samples representing an overlapping set of three-millimeter diameter cores extending the entire length of the SSX traverse could be returned to the surface. A pneumatic prototype has been built which penetrated easily to the bottom of an eight meter vertical test facility. An electric prototype is now under construction. It is expected that the SSX will be able to penetrate through sand or mixed regolith, ice, permafrost, or solid rock, such as basalt. For pure or nearly pure ice applications, the device may be augmented with hot water jets to melt the ice and stir any sediment which may build up ahead of the vehicle. It is expected that an SSX approximately one meter long, three to four centimeters in diameter, and with a power budget of approximately 200 Watts will be able to explore up to approximately five kilometers deep at the rate of about ten meters per day.

Wilcox, B. H.↗

A Review of International Space Station Extravehicular Activity Micrometeoroid and Orbital Debris Risk

Nearly 300 spacewalks have been conducted over the last 25 years to support the construction and maintenance of the International Space Station (ISS). During the nearly 2,000 hours of extra-vehicular activity (EVA), crew wore extra-vehicular mobility unit (EMU) “spacesuits” to help mitigate hazards of the space environment including impacts from micrometeoroid and orbital debris (MMOD) particles. The National Aeronautics and Space Administration (NASA) conducts detailed EMU MMOD risk analyses as part of the ISS EVA review and approval process. This paper provides a general historical overview of the ISS EVA MMOD risks and the associated risk assessment process. The NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) Team produces the ISS EVA MMOD risk analyses using the Bumper MMOD risk analysis code in conjunction with detailed information about the EVA including crew member EVA work sites, crew translation paths, suit orientation, and durations. Detailed physical models of the EMU spacesuit and the ISS are included and tailored for each EVA analysis. Two types of MMOD risk are included: (1) Penetration, and (2) Catastrophic. Penetration risk is for any size leak in the EMU suit. Catastrophic risk is a subset of Penetration Risk and only includes penetrations that cause a 4mm diameter hole (or larger) in the pressure-maintaining “bladder” layer of the EMU suit. This size hole will exceed the ability of the EMU suit to compensate. The MMOD risk analyses also utilize the latest orbital debris environment and meteoroid environment models including additional transient factors to account for recent satellite break-ups and annual meteor storms. These additional factors and the associated increase in EVA MMOD risk are considered when scheduling EVAs to reduce EMU MMOD risk.

Dana M. Lear↗

A Review of International Space Station Extravehicular Activity Micrometeoroid and Orbital Debris Risk

Nearly 300 spacewalks have been conducted over the last 25 years to support the construction and maintenance of the International Space Station (ISS). During the nearly 2,000 hours of extra-vehicular activity (EVA), crew wore extra-vehicular mobility unit (EMU) “spacesuits” to help mitigate hazards of the space environment including impacts from micrometeoroid and orbital debris (MMOD) particles. The National Aeronautics and Space Administration (NASA) conducts detailed EMU MMOD risk analyses as part of the ISS EVA review and approval process. This paper provides a general historical overview of the ISS EVA MMOD risks and the associated risk assessment process. The NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) Team produces the ISS EVA MMOD risk analyses using the Bumper MMOD risk analysis code in conjunction with detailed information about the EVA including crew member EVA work sites, crew translation paths, suit orientation, and durations. Detailed physical models of the EMU spacesuit and the ISS are included and tailored for each EVA analysis. Two types of MMOD risk are included: (1) Penetration, and (2) Catastrophic. Penetration risk is for any size leak in the EMU suit. Catastrophic risk is a subset of Penetration Risk and only includes penetrations that cause a 4mm diameter hole (or larger) in the pressure-maintaining “bladder” layer of the EMU suit. This size hole will exceed the ability of the EMU suit to compensate. The MMOD risk analyses also utilize the latest orbital debris environment and meteoroid environment models including additional transient factors to account for recent satellite break-ups and annual meteor storms. These additional factors and the associated increase in EVA MMOD risk are considered when scheduling EVAs to reduce EMU MMOD risk.

Dana M. Lear↗

Lessons Learned from Performance Testing of Humans in Spacesuits in Simulated Reduced Gravity

Introduction: The overarching objective of the Integrated Suit Test (IST) series is to evaluate suited human performance using reduced-gravity analogs and learn what aspects of an EVA suit system affect human performance. For this objective to be successfully achieved, the testing methodology should be valid and reproducible, and the partial-gravity simulations must be as accurate and realistic as possible. Objectives: To highlight some of the key lessons learned about partial-gravity analogs and testing methodology, and to suggest considerations for optimizing the effectiveness and quality of results of future tests. Methods: Performance testing of suited and unsuited subjects was undertaken in different reduced-gravity analogs including the Space Vehicle Mockup Facility s Partial Gravity Simulator (POGO), parabolic flight on the C-9 aircraft, underwater environments including NASA s Extreme Environment Mission Operations (NEEMO) and the Neutral Buoyancy Lab (NBL), and in field analogs including Desert Research and Technology Studies (RATS), the Haughton Mars Project (HMP), and the JSC Rock Pile. Subjects performed level walking, incline/decline walking, running, shoveling, picking up and transferring rocks, kneeling/standing, and task boards. Lessons Learned Analogs: No single analog will properly simulate all aspects of the true partial-gravity environment. The POGO is an ideal environment from the standpoint that there are no time limits or significant volumetric constraints, but it does have several limitations. It allows only 2 translational degrees of freedom (DOF) and applies true partial-gravity offload only through the subject s center of gravity (CG). Also, when a subject is doing non-stationary tasks, significant overhead inertia from the lift column seems to have a negative impact on performance. Parabolic flight allows full translational and rotational DOF and applies offload to all parts of the body, but the simulation lasts less than 30 seconds. When this is coupled with the volumetric constraints of the plane, both task selection and data collection options are significantly limited. The underwater environments also allow all 6 DOF and allow off-loading to be applied throughout the body, but the data collection capabilities are limited to little more than subjective ratings. In addition, water drag negatively affects performance of tasks requiring dynamic motion. Field analogs provide the ability to simulate lunar terrain and more realistic mission-like objectives, but all of them operate at 1-g, so suited human performance testing generally must utilize a reduced-mass or "mockup" suit, depending on study objectives. In general, the ground-based overhead-suspension partial-gravity analogs like POGO allow the most diverse data collection methods possible while still simulating partial gravity. However, as currently designed, the POGO has significant limitations. Design of the Active Response Gravity Offload System (ARGOS) has begun and is focusing on adding full x,y,z translational DOF, improved offload accuracy, increased lift capacity, and active control of the x and y axes to minimize offload system inertia. Additionally, a new gimbal is being designed to reduce mass and inertia and to be able to work with different suits, as the current gimbal only supports suited testing with the Mark III Technology Demonstrator Suit (MKIII).

Norcross, Jason R.↗

Software engineering

Today's software systems generally use obsolete technology, are not integrated properly with other software systems, and are difficult and costly to maintain. The discipline of reverse engineering is becoming prominent as organizations try to move their systems up to more modern and maintainable technology in a cost effective manner. The Johnson Space Center (JSC) created a significant set of tools to develop and maintain FORTRAN and C code during development of the space shuttle. This tool set forms the basis for an integrated environment to reengineer existing code into modern software engineering structures which are then easier and less costly to maintain and which allow a fairly straightforward translation into other target languages. The environment will support these structures and practices even in areas where the language definition and compilers do not enforce good software engineering. The knowledge and data captured using the reverse engineering tools is passed to standard forward engineering tools to redesign or perform major upgrades to software systems in a much more cost effective manner than using older technologies. The latest release of the environment was in Feb. 1992.

Fridge, Ernest M., III↗

Preliminary Investigation of Civil Tiltrotor in NextGen Airspace

Presentation intro: Tiltrotor aircraft have long been envisioned as being a potentially viable means of commercial aviation transport. Preliminary results from an ongoing study into the operational and technological considerations of Civil Tiltrotor (CTR) operation in the Next Generation airspace, circa the 2025 time-frame, are presented and discussed. In particular, a fleet of CTR aircraft has been conceptually designed. The performance characteristics of this CTR fleet was subsequently translated into BADA (Base of Aircraft DAta) models that could be used as input to emulate CTR aircraft operations in the ACES and AvTerminal airspace and terminal area simulation tools. A network of nine North-Eastern corridor airports is the focus of the airspace simulation effort; the results from this airport network viII then be extrapolated to provide insights into systemic impact of CTRs on the National Airspace System (NAS). Future work will also be detailed as to attempts to model the systemic effects of noise and emissions from this fleet of new aircraft as well as assess their leveraged impact on public service missions, in time of need, such as major regional/national disaster relief efforts. The ideal outcome of this study is a set of results whereby Next Gen airspace CONOPs can be refined to reflect potential CTR capabilities and, conversely, CTR technology development efforts can be better informed as to key performance requirement thresholds needed to be met in order to successfully introduce these aircraft into civilian aviation operation.

Young, Larry A.↗

Two-stage, low noise advanced technology fan. 5: Acoustic final report

The NASA Q2S(quiet two-stage) fan is a 0.836m (32.9 in.) diameter model of the STF 433 engine fan, selected in a 1972 study for an Advanced Technology Transport (ATT) airplane. Noise-control features include: low tip speed, moderate stage pressure rise, large blade-vane spacings, no inlet guide vanes, and optimum blade and vane numbers. Tests were run on the baseline Q2S fan with standard inlet and discharge ducts. Further tests were made of a translating centerbody sonic inlet device and treated discharge ducts. Results were scaled to JT8D and JT3D engine fan size for comparison with current two-stage fans, and were also scaled to STF 433 fan size to compare calculated ATT flyover noise with FAR 36 limits. Baseline Q2S results scaled to JT8D and JT3D engine fan sizes showed substantial noise reductions. Calculated unsuppressed baseline ATT flyovers averaged about 2.5 EPNdB below FAR 36 limits. Using measured sonic inlet results, scaled baseline Q2S fan results, and calculated attenuations for a 1975 technology duct liner, projected flyover noise calculations for the ATT averaged about FAR 36 limits minus 10 EPNdB. Advances in suppression technology required to meet the 1985 goal of FAR 36 limits minus 20 EPNdB are discussed.

Sofrin, T. G.↗

Making and Inspecting Large Wire Grids

Old techniques refined and combined to make new polarizers. Equipment and procedures developed for fabrication and inspection of large, precisely-spaced, flat grids of wire. Technology includes refinements and combinations of established techniques for winding grids of electron tubes and ruling optical gratings and incorporates recent developments in electronic control and laser/electronic-based metrology. Wire wrapped on frame half translated under automatic control to achieve desired space between turns. Frame halves put together, and excess wire cut away, leaving finished grid mounted in frame. Useful as polarizers and beam splitters for electromagnetic radiation in overlapping ranges of long infrared and microwaves.

Magner, Thomas J.↗

High-efficiency 20 GHz traveling wave tube development for space communications

A 75 watt CW high efficiency helix TWT operating at 20 GHz was developed for satellite communication systems. The purpose was to extend the performance capabilities of helix TWTs by using recent technology developments. The TWT described is a unique design because high overall efficiency is obtained with a low perveance beam. In the past, low perveance designs resulted in low beam efficiencies. However, due to recent breakthoughs in diamond rod technology and in collector electrode materials, high efficiencies can now be achieved with low perveance beams. The advantage of a low perveance beam is a reduction in space charge within the beam which translates to more efficient collector operation. In addition, this design incorporates textured graphite electrodes which further enhance collector operation by suppressing backstreaming secondaries. The diamond supported helix circuit features low RF losses, high interaction impedance, good thermal handling capability and has been designed to compensate for the low perveance beam. One more discussed tube feature is the use of a velocity taper in the output helix that achieves low signal distortion while maintaining high efficiency.

Aldana, S. L.↗

Joining and Integration of Silicon Carbide for Turbine Engine Applications

The critical need for ceramic joining and integration technologies is becoming better appreciated as the maturity level increases for turbine engine components fabricated from ceramic and ceramic matrix composite materials. Ceramic components offer higher operating temperatures and reduced cooling requirements. This translates into higher efficiencies and lower emissions. For fabricating complex shapes, diffusion bonding of silicon carbide (SiC) to SiC is being developed. For the integration of ceramic parts to the surrounding metallic engine system, brazing of SiC to metals is being developed. Overcoming the chemical, thermal, and mechanical incompatibilities between dissimilar materials is very challenging. This presentation will discuss the types of ceramic components being developed by researchers and industry and the benefits of using ceramic components. Also, the development of strong, crack-free, stable bonds will be discussed. The challenges and progress in developing joining and integration approaches for a specific application, i.e. a SiC injector, will be presented.

Halbig, Michael C.↗

ISS Payload Operations Training Throughout the COVID-19 Pandemic: Impacts, Opportunities and Solutions

The onset of the COVID-19 pandemic brought a dramatic and rapid transformation to almost every aspect of humanity. The world’s space agencies and their missions were not immune to the wide-sweeping changes. One discipline principally affected was mission operations and the various groups supporting that function. Mission support teams, especially for complex and crewed missions like the International Space Station (ISS) were forced to rethink how and where control center staff performed their vital work. Operations training – an essential element to mission ops, had unique hurdles to overcome. Operations training is responsible for preparing astronaut crews for their missions, training and certifying flight controllers, as well as ensuring that new team members are ready to join their colleagues. Every element of training was impacted during the pandemic. From orientation and introductory classes for new controllers, simulations, and advanced lessons, On the Job Training (OJT) and final evaluations; all aspects faced challenges. Trainers at NASA’s Marshall Space Flight Center in Huntsville, Alabama were forced to become more efficient with trainees and resources to continue supporting ISS payload operations. The pandemic arrived in the USA in March 2020. Immediately, NASA mandated that the support for ISS real-time operations was critical. As a result, physical access to key facilities was restricted. Trainers and trainees had to quickly shift to 100% remote learning. In the short term, this was not a problem. However, instructors discovered lessons they were accustomed to delivering in a classroom environment often did not translate to remote teaching. Another hurdle to operations training was the mandate that all simulations could only be held remotely. The logistics of even small simulations proved to be challenging due to Information Technology (IT) restrictions and public internet limitations. With simulations essentially halted, as well as the restrictions on most OJT, trainees were essentially stopped in their advancement towards certification. Once limitations were identified, trainers prioritized new options. Transitioning to all electronic learning materials was a relatively easy fix. Teaching to large groups took additional shifts in the training paradigm. Methods for preparing astronauts for their missions were revised. Simulation supervisors found efficient techniques to provide realistic training experiences. Communication and coordination with management was essential. In every case, the payload operations instructors found novel solutions to all functions listed. This paper discusses the factors and solutions payloads operations trainers found to keep scientific research on the ISS flying forward to mission success.

ISS↗

A Historical Overview of International Space Station Extravehicular Activity Meteoroid and Orbital Debris Risk

Nearly 300 spacewalks have been conducted over the last 25 years to help build and maintain the International Space Station (ISS). During the nearly 2,000 hours of extra-vehicular activity (EVA), crew members wear extra-vehicular mobility unit (EMU) “spacesuits” to mitigate hazards of the space environment including impacts from meteoroid and orbital debris (MMOD) particles. NASA includes detailed EMU MMOD risk analyses as part of the ISS EVA review and approval process. This paper provides a general historical overview of the ISS EVA MMOD risks and the associated risk assessment process. The NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) Team produces the ISS EVA MMOD risk analyses using the Bumper3 MMOD risk analysis code in conjunction with detailed information about the EVA including crew-member EVA work sites, crew translation paths, suit orientation, and duration. Detailed physical models of the EMU spacesuits and the ISS are included and tailored for each EVA analysis. Two types of MMOD risk are included: (1) Penetration, and (2) Catastrophic. Penetration risk is for any size leak in the EMU suit. Catastrophic risk is a subset of Penetration Risk and only includes penetrations that cause a 4mm diameter hole (or larger) in the inner “bladder” layer of the EMU suit. This size hole will exceed the ability of the EMU suit to compensate. The MMOD risk analyses also utilize the latest orbital debris environment and meteoroid environment models including additional transient factors to account for recent satellite break-ups and annual meteor storms. These additional factors and the associated increase in EVA MMOD risk are considered when scheduling an EVA to reduce EMU MMOD risk.

Dana M. Lear↗

Technology Transfer Challenges: A Case Study of User-Centered Design in NASA's Systems Engineering Culture

The Upper Stage (US) section of the National Aeronautics and Space Administration's (NASA) Ares I rocket will require internal access platforms for maintenance tasks performed by humans inside the vehicle. Tasks will occur during expensive critical path operations at Kennedy Space Center (KSC) including vehicle stacking and launch preparation activities. Platforms must be translated through a small human access hatch, installed in an enclosed worksite environment, support the weight of ground operators and be removed before flight - and their design must minimize additional vehicle mass at attachment points. This paper describes the application of a user-centered conceptual design process and the unique challenges encountered within NASA's systems engineering culture focused on requirements and "heritage hardware". The NASA design team at Marshall Space Flight Center (MSFC) initiated the user-centered design process by studying heritage internal access kits and proposing new design concepts during brainstorming sessions. Simultaneously, they partnered with the Technology Transfer/Innovative Partnerships Program to research inflatable structures and dynamic scaffolding solutions that could enable ground operator access. While this creative, technology-oriented exploration was encouraged by upper management, some design stakeholders consistently opposed ideas utilizing novel, untested equipment. Subsequent collaboration with an engineering consulting firm improved the technical credibility of several options, however, there was continued resistance from team members focused on meeting system requirements with pre-certified hardware. After a six-month idea-generating phase, an intensive six-week effort produced viable design concepts that justified additional vehicle mass while optimizing the human factors of platform installation and use. Although these selected final concepts closely resemble heritage internal access platforms, challenges from the application of the user-centered process provided valuable lessons for improving future collaborative conceptual design efforts.

Quick, Jason↗

COSMIC/NASTRAN-PATRAN Interface

A three dimensional solid modeling and finite element pre and postprocessing program, PATRAN, uses the latest interactive computer graphics technology, provides a visual means to define a finite element model and its environment, and reviews its resultant model behavior. The capabilities provided by the PATRAN-COSMIC/NASTRAN interface are discussed. While the translator capabilities give some indication of the interface quality between the two programs, there are other attributes to be considered. The ideal interface would be a user transparent union of the two programs so that the engineer could move from one program to the other fluently and naturally. Hence, a valid assessment of the interface completeness must consider how close the current capabilities are to the idealized case. An example problem is presented to demonstrate how COSMIC/NASTRAN and PATRAN can be used together to meet the requirements of an actual engineering application.

Libby, D. H.↗

Electric propulsion applications enabled by space nuclear power

Electric propulsion promises the advantage of providing high Isp's for placing payloads into their assigned orbits. This translates into heavier payloads using a given lift capability or, conversely, the use of smaller boosters. To accomplish this, high electric powers are required. Space reactor power systems such as SP-100 enable this technology. The electric propulsion requirements needed, namely, their power requirements and the resulting payload masses and time-to-orbit, are shown. Also indicated are the missions most benefitting from the use of electric propulsion. An Interim Reference Mission is described, synthesizing the results shown, for demonstration purposes.

Vicente, F. A.↗

A Green Propulsion Dual Mode (GPDM) In-Space Technology Demonstration on a 6U CubeSat

Over the past decade there has been an increase in the launch and operations of small spacecraft. Small spacecraft (defined as having a total vehicle mass of < 180 kg) provide an opportunity for low-cost, high impact technology demonstrations on a small scale. They also create opportunities for government, industry, and academic to engage, transfer knowledge, and extend partnerships with non-traditional partners. NASA’s Marshall Space Flight Center (MSFC) is leading a collaborative effort to demonstrate a dual-mode (chemical and electrospray) propulsion system using a common propellant system as a payload on a 6U CubeSat. The novel feature in the propulsion system is the interfacing of propulsion technologies requiring dramatically different operating conditions and support hardware. GPDM will use a low toxicity or “green” propellant known as Advanced Spacecraft Energetic Non-Toxic (ASCENT) to demonstrate using a chemical thruster for translation burns and electrospray propulsion for both attitude control and translational burns on the spacecraft. Specific mission activities could include demonstration of collision avoidance during frequent altitude adjustment maneuvers to validate thruster performance and managing extended duration thruster burns of at least 24 hours with limited vehicle contact times. This paper will summarize the ground testing, spacecraft development, mission objectives, and mission planning activities to achieve some of GPDM’s technical objectives.

Nehemiah Joel Williams↗