Search NASA⌕ Search

SEARCH · Search NASA

Results for “traffic controls”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Simulation studies of STOL airplane operations in metropolitan downtown and airport air traffic control environments

The operating problems and equipment requirements for STOL airplanes in terminal area operations in simulated air traffic control (ATC) environments were studied. These studies consisted of Instrument Flight Rules (IFR) arrivals and departures in the New York area to and from a downtown STOL port, STOL runways at John F. Kennedy International Airport, or STOL runways at a hypothetical international airport. The studies were accomplished in real time by using a STOL airplane flight simulator. An experimental powered lift STOL airplane and two in-service airplanes having high aerodynamic lift (i.e., STOL) capability were used in the simulations.

Sawyer, R. H.↗
NASA NTRS1987

An expert system for air traffic control system

The objective was to design a control logic which automates all or part of the guidance function for air traffic control systems. Particular interest was focused on automation of the terminal area control system. A preliminary study was done on the development of an expert system. The system may be used to assist controllers by providing them with feasible options in guiding each aircraft in the control area to its desired destination.

Sensui, Takashi↗
NASA NTRS2016

Trajectory Specification for Automation of Terminal Air Traffic Control

"Trajectory specification" is the explicit bounding and control of aircraft tra- jectories such that the position at each point in time is constrained to a precisely defined volume of space. The bounding space is defined by cross-track, along-track, and vertical tolerances relative to a reference trajectory that specifies position as a function of time. The tolerances are dynamic and will be based on the aircraft nav- igation capabilities and the current traffic situation. A standard language will be developed to represent these specifications and to communicate them by datalink. Assuming conformance, trajectory specification can guarantee safe separation for an arbitrary period of time even in the event of an air traffic control (ATC) sys- tem or datalink failure, hence it can help to achieve the high level of safety and reliability needed for ATC automation. As a more proactive form of ATC, it can also maximize airspace capacity and reduce the reliance on tactical backup systems during normal operation. It applies to both enroute airspace and the terminal area around airports, but this paper focuses on arrival spacing in the terminal area and presents ATC algorithms and software for achieving a specified delay of runway arrival time.

air traffic control↗
NASA NTRS1993

Development and evaluation of a profile negotiation process for integrating aircraft and air traffic control automation

The development and evaluation of the profile negotiation process (PNP), an interactive process between an aircraft and air traffic control (ATC) that integrates airborne and ground-based automation capabilities to determine conflict-free trajectories that are as close to an aircraft's preference as possible, are described. The PNP was evaluated in a real-time simulation experiment conducted jointly by NASA's Ames and Langley Research Centers. The Ames Center/TRACON Automation System (CTAS) was used to support the ATC environment, and the Langley Transport Systems Research Vehicle (TSRV) piloted cab was used to simulate a 4D Flight Management System (FMS) capable aircraft. Both systems were connected in real time by way of voice and data lines; digital datalink communications capability was developed and evaluated as a means of supporting the air/ground exchange of trajectory data. The controllers were able to consistently and effectively negotiate nominally conflict-free vertical profiles with the 4D-equipped aircraft. The actual profiles flown were substantially closer to the aircraft's preference than would have been possible without the PNP. However, there was a strong consensus among the pilots and controllers that the level of automation of the PNP should be increased to make the process more transparent. The experiment demonstrated the importance of an aircraft's ability to accurately execute a negotiated profile as well as the need for digital datalink to support advanced air/ground data communications. The concept of trajectory space is proposed as a comprehensive approach for coupling the processes of trajectory planning and tracking to allow maximum pilot discretion in meeting ATC constraints.

Green, Steven M.↗
NASA NTRS2002

A Life-Cycle Cost Estimating Methodology for NASA-Developed Air Traffic Control Decision Support Tools

This paper describes the development of a life-cycle cost (LCC) estimating methodology for air traffic control Decision Support Tools (DSTs) under development by the National Aeronautics and Space Administration (NASA), using a combination of parametric, analogy, and expert opinion methods. There is no one standard methodology and technique that is used by NASA or by the Federal Aviation Administration (FAA) for LCC estimation of prospective Decision Support Tools. Some of the frequently used methodologies include bottom-up, analogy, top-down, parametric, expert judgement, and Parkinson's Law. The developed LCC estimating methodology can be visualized as a three-dimensional matrix where the three axes represent coverage, estimation, and timing. This paper focuses on the three characteristics of this methodology that correspond to the three axes.

Wang, Jianzhong Jay↗
NASA NTRS1992

Design and evaluation of an advanced air-ground data-link system for air traffic control

The design and evaluation of the ground-based portion of an air-ground data-link system for air traffic control (ATC) are described. The system was developed to support the 4D Aircraft/ATC Integration Study, a joint simulation experiment conducted at NASA's Ames and Langley Research Centers. The experiment focused on airborne and ground-based procedures for handling aircraft equipped with a 4D-Flight Management System (FMS) and the system requirements needed to ensure conflict-free traffic flow. The Center/TRACON Automation System (CTAS) at Ames was used for the ATC part of the experiment, and the 4D-FMS-equipped aircraft was simulated by the Transport Systems Research Vehicle (TSRV) simulator at Langley. The data-link system supported not only conventional ATC communications, but also the communications needed to accommodate the 4D-FMS capabilities of advanced aircraft. Of great significance was the synergism gained from integrating the data link with CTAS. Information transmitted via the data link was used to improve the monitoring and analysis capability of CTAS without increasing controller input workload. Conversely, CTAS was used to anticipate and create prototype messages, thus reducing the workload associated with the manual creation of data-link messages.

Denbraven, Wim↗
NASA NTRS2004

Situation Awareness Implications of Adaptive Automation of Air Traffic Controller Information Processing Functions

The goal of this research was to define a measure of situation awareness (SA) in an air traffic control (ATC) task and to assess the influence of adaptive automation (AA) of various information processing functions on controller perception, comprehension and projection. The measure was also to serve as a basis for defining and developing an approach to triggering dynamic control allocations, as part of AA, based on controller SA. To achieve these objectives, an enhanced version of an ATC simulation (Multitask (copyright)) was developed for use in two human factors experiments. The simulation captured the basic functions of Terminal Radar Approach Control (TRACON) and was capable of presenting to operators four different modes of control, including information acquisition, information analysis, decision making and action implementation automation, as well as a completely manual control mode. The SA measure that was developed as part of the research was based on the Situation Awareness Global Assessment Technique (SAGAT), previous goal-directed task analyses of enroute control and TRACON, and a separate cognitive task analysis on the ATC simulation. The results of the analysis on Multitask were used as a basis for formulating SA queries as part of the SAGAT-based approach to measuring controller SA, which was used in the experiments. A total of 16 subjects were recruited for both experiments. Half the subjects were used in Experiment #1, which focused on assessing the sensitivity and reliability of the SA measurement approach in the ATC simulation. Comparisons were made of manual versus automated control. The remaining subjects were used in the second experiment, which was intended to more completely describe the SA implications of AA applied to specific controller information processing functions, and to describe how the measure could ultimately serve as a trigger of dynamic function allocations in the application of AA to ATC. Comparisons were made of the sensitivity of the SA measure to automation manipulations impacting both higher-order information processing functions, such as information analysis and decision making, versus lower-order functions, including information acquisition and action implementation. All subjects were exposed to all forms of AA of the ATC task and the manual control condition. The approach to AA used in both experiments was to match operator workload, assessed using a secondary task, to dynamic control allocations in the primary task. In total, the subjects in each experiment participated in 10 trials with each lasting between 45 minutes and 1 hour. In both experiments, ATC performance was measured in terms of aircraft cleared, conflicting, and collided. Secondary task (gauge monitoring) performance was assessed in terms of a hit-to-signal ratio. As part of the SA measure, three simulation freezes were conducted during each trial to administer queries on Level 1, 2, and 3 SA.

Kaber, David B.↗
NASA NTRS1965

Effects of the Air Traffic Control System on the Supersonic Transport

A study of the problems anticipated with the introduction of the supersonic transport into the air traffic control system indicated that supersonic transport design allowances for time and fuel for maneuvering during climbouts may not be sufficient, that there is a greater communications-navigation work- load for the supersonic transport than for the subsonic jet transport during descent, and that use of a flight director to command pitch control guidance for the pilot would be helpful.

Norman S. Silsby↗
NASA NTRS1980

Cockpit displayed traffic information and distributed management in air traffic control

A graphical display of information (such as surrounding aircraft and navigation routes) in the cockpit on a cathode ray tube has been proposed for improving the safety, orderliness, and expeditiousness of the air traffic control system. An investigation of this method at NASA-Ames indicated a large reduction in controller verbal work load without increasing pilot verbal load; the visual work may be increased. The cockpit displayed traffic and navigation information system reduced response delays permitting pilots to maintain their spacing more closely and precisely than when depending entirely on controller-issued radar vectors and speed command.

Kreifeldt, J. G.↗
NASA NTRS2003

Auction Mechanism to Allocate Air Traffic Control Slots

This article deals with an auction mechanism for airspace slots, as a means of solving the European airspace congestion problem. A disequilibrium, between Air Traffic Control (ATC) services supply and ATC services demand are at the origin of almost one fourth of delays in the air transport industry in Europe. In order to tackle this congestion problem, we suggest modifying both pricing and allocation of ATC services, by setting up an auction mechanism. Objects of the auction will be the right for airlines to cross a part of the airspace, and then to benefit from ATC services over a period corresponding to the necessary time for the crossing. Allocation and payment rules have to be defined according to the objectives of this auction. The auctioneer is the public authority in charge of ATC services, whose aim is to obtain an efficient allocation. Therefore, the social value will be maximized. Another objective is to internalize congestion costs. To that end, we apply the principle of Clarke-Groves mechanism auction: each winner has to pay the externalities imposed on other bidders. The complex context of ATC leads to a specific design for this auction.

Raffarin, Marianne↗
NASA NTRS1994

Presentation of a Swedish study program concerning recruitment, selection and training of student air traffic controllers: The MRU project phase 1

The Director of the ANS Department has set up an objective for the efficiency of screening and training procedures for air traffic controller students which implies that all students admitted 'shall be considered to have the qualification for - and be given the means of - completing the training'. As a consequence, a study project has been established. It is run by the ANS Department with members from the Swedish CAA, in close cooperation with Uppsala University.

Haglund, Rune↗
NASA NTRS2006

Automation for "Direct-to" Clearances in Air-Traffic Control

A method of automation, and a system of computer hardware and software to implement the method, have been invented to assist en-route air-traffic controllers in the issuance of clearances to fly directly to specified waypoints or navigation fixes along straight paths that deviate from previously filed flight plans. Such clearances, called "direct-to" clearances, have been in use since before the invention of this method and system.

Erzberger, Heinz↗
NASA NTRSDate not supplied

Transcribing Air Traffic Control System Command Center Planning Telecons Using Cloud-Based Automatic Speech Recognition

This paper addresses the challenge of using Automatic Speech Recognition (ASR) technology to transcribe regular teleconferences that happen between FAA Air Traffic Control System Command Center (ATCSCC) planners, stakeholders and air users. These planning teleconferences (aka telecons or planning webinars) are an integral part of managing air traffic in the U.S. National Airspace System (NAS). In particular, the meetings facilitate the creation and modification of various traffic management initiatives (TMIs), that are used to regulate the flow of air traffic. This is typically a human intensive process, requiring specialists to listen to the entire meeting audio (10-20 minutes duration) and inferring the state of the NAS (e.g., weather phenomenon) that was discussed. It would be advantageous to have digital transcripts of the audio and have useful information (e.g., related to TMIs) automatically extracted from the transcripts. In this regard, we are exploring the adoption of state-of-the-art speech to text and Natural Language Processing (NLP) tools that will achieve our objective of digitizing the webinar audio. Unfortunately, the highly technical phraseology present in the audio and limited data availability for model building make ASR difficult. To overcome this challenge, we have taken the critical first step in creating a human transcription dataset from ~20 hours of speech in the ATCSCC audio with the help of subject matter experts. A novelty of our work is the creation of a ground truth transcription dataset for ATCSCC teleconference webinars, which is particularly important for Aviation domain-specific NLP tasks. Using Microsoft Speech Studio, a cloud-based ASR platform, we have fine-tuned the English pre-trained ASR models (available in speech studio) and achieved an average word error rate (WER) of 6.81%. The baseline ASR also provides a digital version of each planning webinar, making it accessible and text-searchable for future references. Additionally, the transcriptions can serve as a bridge between raw audio data and a range of text-based NLP tasks, such as named entity recognition (NER) and intent classification, potentially enhancing the digital footprint of the webinars and other connected data sources. Our work has several potential applications. Firstly, the transcriptions can be analyzed to understand the complex decision process of creating, implementing and modifying TMIs and may also contribute to TMI prediction services. Secondly, our dataset and model can be used to develop more accurate ASR systems for aviation-specific language, which can bring about digital communication in the aviation industry (and aid current “voice only” communications, which are inherently error-prone). Lastly, the transcriptions themselves can be used as a valuable resource for training other NLP models.

Stephen S. B. Clarke↗
NASA NTRS1991

Human factors issues in the use of artificial intelligence in air traffic control. October 1990 Workshop

The objective of the workshop was to explore the role of human factors in facilitating the introduction of artificial intelligence (AI) to advanced air traffic control (ATC) automation concepts. AI is an umbrella term which is continually expanding to cover a variety of techniques where machines are performing actions taken based upon dynamic, external stimuli. AI methods can be implemented using more traditional programming languages such as LISP or PROLOG, or they can be implemented using state-of-the-art techniques such as object-oriented programming, neural nets (hardware or software), and knowledge based expert systems. As this technology advances and as increasingly powerful computing platforms become available, the use of AI to enhance ATC systems can be realized. Substantial efforts along these lines are already being undertaken at the FAA Technical Center, NASA Ames Research Center, academic institutions, industry, and elsewhere. Although it is clear that the technology is ripe for bringing computer automation to ATC systems, the proper scope and role of automation are not at all apparent. The major concern is how to combine human controllers with computer technology. A wide spectrum of options exists, ranging from using automation only to provide extra tools to augment decision making by human controllers to turning over moment-by-moment control to automated systems and using humans as supervisors and system managers. Across this spectrum, it is now obvious that the difficulties that occur when tying human and automated systems together must be resolved so that automation can be introduced safely and effectively. The focus of the workshop was to further explore the role of injecting AI into ATC systems and to identify the human factors that need to be considered for successful application of the technology to present and future ATC systems.

Hockaday, Stephen↗