Search NASA⌕ Search

SEARCH · Search NASA

Results for “transmission electron microscope”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Inefficient Growth of Refractory Grains: Implications for Grains in the Solar Nebula

Introduction: We report the results of a sounding rocket experiment in which SiO nucleation and growth in an argon atmosphere was observed in microgravity starting from a vapor generated by evaporation of waterglass deposited on a heated Ta wire. The temperature and pressure at the point of nucleation was determined using a double wavelength Mach–Zehnder-type interferometer. The particle composition and grain size distribution were measured after payload recovery using a Transmission Electron Microscope (TEM; JEM-2100F. JEOL Ltd., Tokyo). The results were analyzed using Modified Classical Nucleation Theory (MCNT)[1]. We report a measurement of the SiO-silicate grain sticking coefficient of 0.016, indicating very inefficient grain growth from the vapor. In other words, for every 100 SiO molecules that collide with a growing grain only one to two are captured. In the only two previous studies of the growth of solid particles from the gas phase the calculated sticking coefficients were much lower. For zinc atoms colliding with zinc crystals only three out of 100,000 collisions resulted in grain growth [2]. Iron atoms colliding with growing iron particles similarly showed an efficiency of ~0.00002 [3]. For zinc, we can explain inefficient growth due to the difficulty of the colliding atom coming upon a vacancy in the growing crystal lattice before it evaporates from the grain surface. The much higher sticking coefficient of SiO molecules on silica grains is reasonable because the silica grains are highly amorphous or glassy and therefore provide a much higher defect density where SiO molecules can be captured into the grains. In the case of similar Fe experiment, the critical cluster was the dimer. In this case the forming dimer returns to the vapor phase by dissociation due to the excess energy from the formation of the Fe-Fe bond.

Joseph A Nuth↗

Unraveling Solar Wind Space Weathering of Carbon-Rich Asterods: Low-Flux VS. High-Flux Ion Irradiation of Murchison

Introduction: Space weathering processesalter the microstructural, compositional, and optical properties of airless planetary surfaces.Solar wind space weatheringforms ion-damaged rims within the outermost ~100 nm of regolith grains through atomic-displacements and implantation of energetic H+and He+ions[1]. Transmission electron microscope(TEM)studies of space weathered Itokawa and lunar olivine particles reveal predominantly nanocrystalline solar wind-damaged rims with only minor regions of amorphization[2-5]. This finding differs from laboratoryion irradiation experiments in which samples become amorphous at fluences 2-3 orders of magnitude lower than the independentlyconstrained fluences for still-crystalline natural samples [6-7].Ion flux is generally considered to have a secondaryeffectcompared to fluence in these irradiation experiments. However, solar wind irradiation of natural samples occurs at a flux that is ~4-5 orders of magnitude lower than whatisused inlaboratory simulations (e.g., [6,8-9]). Constraining how the very low ion flux of solar wind influences the microstructural, chemical, and spectral alteration of silicate minerals will improve our understanding of solar wind space weathering and aid in the analysis of returned samples from the Hayabusa2 and OSIRIS-REx missions. Here we report results from low-and high-flux ion irradiation experiments on the Murchison (CM2)meteoritewithcomparable total fluences. Methods: We performed low-flux and high-flux He+(4 keV) and H+(1 keV) irradiation experiments on separate, dry-cut Murchison slabs. Low-flux He+irradiation reached a total fluence of 2.1 x 1016ions/cm2(~400 years of exposure at Bennu) using a flux of 3.6 x 1011ions/cm2/s; low-flux H+irradiation reached a total fluence of 3.9 x 1016ions/cm2(~30 years) using a flux of 6.6 x 1011ions/cm2/s. High-flux He+irradiation reached a total fluence of 2.0 x 1016ions/cm2(~400 years)using a flux of 9.1 x 1012ions/cm2/s; high-flux H+irradiation reached a total fluence of 5.8 x 1016ions/cm2(~50 years)using flux of 8.4 x 1012ions/cm2/s. By irradiating to similar total fluences in both the low-flux and high-flux experiments, we can better isolate and evaluatethe effects of ion flux. Differences between unirradiatedand irradiated surfaces are determined using threeanalytical techniques:(1) in situX-ray photoelectron spectroscopy(XPS) reveals changes in surface chemistry,(2) visible to near-infrared spectroscopy (VNIR; 0.35-2.5 μm) highlights changes in spectraltrends, such as albedo and slope, and (3) TEM and energy-dispersive X-ray spectroscopy (EDS) identifieschanges in nanoscale structure and elemental composition within olivine and matrix electron-transparent thin sections prepared using focused ion beam scanning electron microscopy (FIB-SEM). Results and Discussion: XPS analyses of the low-fluxand high-fluxHe+-and H+-irradiated samples showa minorreduction in surface carbon contentand chemicalreduction ofFe3+to Fe2+. The latter result is consistent with the higher Fe2+/Fe3+ratios observed in phyllosilicate-rich space weathered rims of Ryugu grains [10].VNIR analyses suggest that the low-flux H+-irradiated spectrum has a slightly bluer slope (over 0.65-2.5 μm) compared to the unirradiated VNIR spectrum from [9] while the low-flux He+-irradiated spectral slope is comparable to the unirradiated surface. Both the high-flux He+-and H+-irradiated VNIR spectra exhibitslightlyhigheralbedos at shorter wavelengths relativeto their unirradiated counterparts, with He+irradiation yielding a greater change. Thus far, the low-flux He+-irradiated matrix and olivine FIBsections as well as the low-flux H+-irradiated olivine FIBsection have been examined with TEM. The surfaces of all three samplesshowless vesiculation than high-flux/high-fluenceirradiated matrix and olivine samples from [9]. The depth of phyllosilicate amorphization in thelow-fluxHe+-irradiated matrix FIBsection varieslaterally, with crystalline domains occurring as shallow as ~25 nm in some regions. Thelow-flux He+-irradiated olivine FIBsection has acontinuous,~40-90 nm thick ion-affected layer with polycrystalline and amorphous microstructures. The low-flux H+-irradiated olivine sampleexhibits a distinct, ~10-40 nm ion-affected layer whose uppermost ~20 nmin thicker regions is predominantly amorphous.Continuing to compare results from this work to those from [9] will provide a comprehensive understanding of how ion flux impacts the microstructural, chemical, and optical modification of various mineral phases and, in turn,help identify space weathering features from parent body alteration in Hayabusa2 and OSIRIS-REx returned samples.

D L Laczniak↗

SURFACE EXOSURE TIMESCALES OF APOLLO CORE SAMPLE 73002 SPACE WEATHERED GRAINS

Introduction: Space weathering causes the surface regolith on airless bodies like the Moon to be morphologically, microstructurally, and chemically altered due to micrometeoroid bombardment and solar wind irradiation[1]. These processes produce a multitude of microstructural and chemical changes in individual soil grains that accumulate as grains are exposed on the surface over time. One microstructural feature produced by exposure to the solar wind is the development of ion-damaged rims on regolith grains via H+ and He+ ion irradiation. Also present are solar energetic particle (SEP) tracks, which are nanoscale lineations of ionization damage within grain interiors formed by high energy solar flare ions(primarily Fe group nuclei) which penetrate millimeters below the surface [2]. Recent work has confirmed that the thickness of solar wind-damaged amorphous rims on anorthite grains, nanocrystalline rims on olivine grains, and their respective SEP track densities are correlated with their surface exposure ages [3].Core sample 73002, recently released under the Apollo Next Generation Sample Analysis (ANGSA) Program, has provided an opportunity to study material collected from the light mantle formation during Apollo 17. The light mantle is thought to have been deposited via a landslide originating from the neighboring South Massif [4]. Spectral profiles and ferromagnetic resonance measurements of bulk soils sampled at cm-intervals from 73002 indicate the existence of mature regolith extending ~8 cm below the surface, suggesting the presence of an in-situ reworking zone in the core[5,6].Here we present the distribution of SEP track densities, solar wind damaged rim widths, and the corresponding surface exposure ages of grains residing in the proposed in-situ reworking zone of core 73002. Methods: Bulk samples of regolith from the first eight intervals and every following fourth interval down the core (dissection Pass 2) were delivered to Purdue University as <45 μm size fractions. The first eight0.5 cm intervals, representing the top 4cmof regolith, were individually dry sieved to a<20 μm size fraction, and grains were prepared by ultramicrotomy for analysis in the scanning transmission electron microscope (STEM). Bright field (BF) and dark field (DF) STEM images of solar flare tracks and solar wind damaged rims were acquired on a JEOL 2500SE TEM, equipped with a 60 mm2ultra-thin window silicon drift energy dispersive X-ray (EDX) spectrometer at NASA John-son Space Center. Grain compositions were determined by EDX compositional spectrum imaging. SEP track densities and amorphous rim thicknesses were measured on BF and DF images. Results: The fraction of grains with discernable space weathering features decreased with depth, with 100% in the first interval exhibiting space weathering features as opposed to ~60% in Interval 8.BF and DF STEM images show splash-melt and vapor deposited rims on outermost grain margins with embedded Fe-bearing nanoparticles ranging in size up to ~10 nm in diameter. Images also show solar-wind damaged rims below the vapor deposits, and SEP tracks present in grain interiors. The rim thicknesses and SEP track densities were determined using the methods of [3] for 54grains spanning the top 4 cm. ~80% of the grains analyzed were anorthite and ~20% were olivine. The track production rate from[3] was used to estimate the surface exposure times of the grains in this study. The majority of exposure times are in the 1 -5 MY range for all intervals. The lowest value was 3.8x 10¬5years in Interval 8and the highest value was1.1x 107years in Interval 6. Grains with the highest solar wind damage rim thicknesses and SEP track densities are found in Interval 6.The highest rim thickness and track density observed for anorthiteis126.5 nm and4.7 x 1011tracks/cm2, while for olivine they are 98.6 nm and 1.83 x 1011tracks/cm2, respectively. Discussion: Intervals from the top 4 cm of 73002 show similar SEP track density and solar wind damaged rim thickness distributions. Spectral and ferromagnetic resonance measurements of 73002 indicate an in-situ reworking zone up to~8 cm below the surface[5,6].The depth analyzed in this work is within the core’s uppermost in-situ reworking zone and may serve as an explanation to the homogenous distribution of exposure ages. The decreasing abundance of space weathered features with depth is consistent with regolith mixing models showing an exponential decay in regolith maturity with depth over time[7].A maximum surface exposure age determined via SEP track density is approximately 10million years. This timescale is consistent with the lower estimate of surface exposure ages of the light mantle determined in previous studies, which can range from 10s to over 100 Ma [4].It also falls within the core regolith reworking development timescale of ~17 Ma [5,6]. Additional analysis will be performed for a further seven intervals in 73002.

J A McFadden↗

Nanoscale Mineralogy of Bennu Samples Returned by OSIRIS-REx

The OSIRIS-REx spacecraft returned regolith samples from asteroid Bennu and an initial sample was allocated for quick-look (QL) analyses. These QL particles were recovered from the avionics deck of the sample canister and were used to test the hypothesis that this dust is broadly representative of the bulk sample. The QL sample analyses showed that the materials are dominated by hydrated silicates, sulfides, magnetite, phosphates, and abundant organic matter, in addition to other minor/trace phases. Here we report our preliminary transmission electron microscope (TEM) observations for the nanoscale mineralogy of Bennu samples.

L P Keller↗

Space Weathering in OSIRIS-REx Samples From Bennu: Impact Melt Deposits

Early analyses of regolith samples from asteroid Bennu delivered by the OSIRIS-REx spacecraft showed a mineralogy dominated by hydrated silicates, sulfides, magnetite, phosphates, and abundant organic matter, in addition to other minor/trace phases. A major objective of the sample analysis campaign is to understand the nature and extent of space weathering processes recorded by returned samples from Bennu. Here we report our preliminary transmission electron microscope (TEM) observations of impact melt deposits on surfaces of Bennu sample particles.

L. P. Keller↗

In-situ Nanoscale Ablation

An understanding of the ablation of carbon-based materials is crucial to modeling the behavior of atmospheric entry spacecrafts equipped with thermal protection systems (TPS).Carbon is the backbone of TPS systems such as PICA (phenolic-impregnated carbon ablator).Therefore in the present work we study ablation of highly oriented pyrolytic graphite (HOPG)in oxygen at temperatures up to 1000°C done within a gas reaction cell housed in a scanning transmission electron microscope (STEM). Observation of the HOPG oxidation on specimens sectioned parallel and normal to the carbon basal planes in the presence of oxygen are reported.Pitting caused by residual oxygen and/or platinum particles from the sectioning process was observed before oxygen gas flow was established at 750°C in the specimen sectioned with the carbon basal planes parallel to the beam direction. Introduction of oxygen flow caused rapid oxidation moving in a uniform front that completely consumed the HOPG in approximately 1.5minutes. The specimen sectioned with the carbon basal planes normal to the beam direction did not show the same pitting phenomenon but exhibited rapid oxidation at 1000°C that proceeded in a uniform front and completed in approximately 1 minute. All specimens tested had a husk resembling the original specimen shape left over after oxidation. It is concluded that this husk is most likely ash impurity from the HOPG or impurities from the sectioning process or E-chip. A residual gas analyszer (RGA) was successfully used to monitor gas flows during the experiments but was yet unsuccessful in monitoring oxidation gas products produced during the experiment.Future studies will optimize the RGA setup in order to maximize the potential for detecting these species. These in-situ studies successfully show how this highly ordered carbon ablates on a nano- and micro-scopic length scale and can be used to provide fundamental understanding of carbon ablation that can be used to design the next-generation of TPS systems.

Nanoscale Ablation↗

Electron microscopy of some experimentally shocked counterparts of lunar minerals.

Particulate samples of experimentally shocked olivine, enstatite, and apatite and their unshocked equivalents were thinned by ion bombardment and examined by transmission methods in a conventional (100 kV) electron microscope. Enstatite shock-loaded at a peak pressure of 250 kb was partly transformed to relatively dense inverse defect spinel. Magnesian olivine shocked at a peak pressure of 200 kb shows intense lattice deformation. Magnesian olivine shock-loaded at a peak pressure of 400 kb was recrystallized to very fine polycrystalline aggregates. Apatite shock-loaded at a peak pressure of 250 kb shows planar deformation elements and shock-induced imperfections.

Sclar, C. B.↗

Ternary Feldspar Within Felste Clasts From Apollo Impact Melt Breccia 72255

Granitic clasts with unique ternary feldspar compositions have been identified within samples of the layered impact melt breccia from Apollo 17 Station 2 Boulder 1 (72215, 72235, 72255 and 72275), and in a felsite clast from station 3 (73215). These “ternary” compositions seemingly plot within the miscibility gap of the albite-anorthite-orthoclase (Ab-An-Or) system. Feldspars with these compositions have not been identified in terrestrial samples, and equilibrium feldspar compositions from laboratory experiments indicate they would not be thermodynamically stable. Thus, the physiochemical processes involved in forming these unique ternary feldspars remain poorly understood. To better constrain the formation of ternary feldspar within lunar breccias, we have undertaken a coordinated scanning electron microscope (SEM)-based coupled electron backscatter diffraction (EBSD) and energy dispersive spectrometry (EDS), electron microprobe analyzer (EPMA) wavelength dispersive spectrometry, and transmission electron microscopy (TEM) study. The goals of this study are twofold: 1) confirm whether ternary feldspar is present as coherent, single-crystals or sub-microscopic intergrowths of normal compositions, and 2) better constrain the formation conditions of clasts containing ternary feldspar.

T. M. Erickson↗

In situ sputter cleaning of thin film metal substrates for UHV-TEM corrosion studies.

A prerequisite for conducting valid corrosion experiments by in situ electron microscopy techniques is not only the achievement of UHV background pressure conditions at the site of the specimen but also the ability to clean the surface of the thin metal substrate specimen before initiation of the corrosive interaction. A miniaturized simple ion gun has been constructed for this purpose. The gun is small enough to be incorporated into an UHV electron microscope specimen chamber with hot stage in such a way as to permit bombardment of the substrate specimen while observing it by transmission electron microscopy TEM. It is shown that the ion beam generated is confined well enough to cause a sputtering removal of substrate material at a rate of approximately 5-10 A/min and to prevent the sputter deposition of contaminating material from the specimen holder.

Heinemann, K.↗

Scanning and Transmission Electron Microscopy of High Temperature Materials

Software and hardware updates to further extend the capability of the electron microscope were carried out. A range of materials such as intermetallics, metal-matrix composites, ceramic-matrix composites, ceramics and intermetallic compounds, based on refractory elements were examined under this research. Crystal structure, size, shape and volume fraction distribution of various phases which constitute the microstructures were examined. Deformed materials were studied to understand the effect of interfacial microstructure on the deformation and fracture behavior of these materials. Specimens tested for a range of mechanical property requirements, such as stress rupture, creep, low cycle fatigue, high cycle fatigue, thermomechanical fatigue, etc. were examined. Microstructural and microchemical stability of these materials exposed to simulated operating environments were investigated. The EOIM Shuttle post-flight samples were also examined to understand the influence of low gravity processing on microstructure. In addition, fractographic analyses of Nb-Zr-W, titanium aluminide, molybdenum silicide and silicon carbide samples were carried out. Extensive characterization of sapphire fibers in the fiber-reinforced composites made by powder cloth processing was made. Finally, pressure infiltration casting of metal-matrix composites was carried out.

Source record↗

Microstructural Evolution of the Civet Cat Norite (72255)

The ‘Civet Cat Norite’ is a ~ 2.5 cm clast within the Apollo impact melt breccia sample 72255 collected during Apollo 17 EVA 2 at Boulder 1. The norite is primarily composed of plagioclase and orthopyroxene with fine-scale exsolution lamellae of augite. The plagioclase and orthopyroxene (OPX) coexist with minor quartz and augitic clinopyroxene (CPX), and accessory apatite, baddeleyite, chromite, ilmenite, loveringite, merrillite, rutile and zircon. The major minerals range from 1 to 4 mm in size and show a cataclastic texture indicated by banding of the light and dark phases]. The chemical composition of the orthopyroxene, augitic exsolution lamellae, and exsolved oxides suggest the norite crystallized in the lower crust of the Moon (10 – 70 km depth) and was subsequently excavated by impact(s). Shock pressure estimates for the norite range from 15 – 35 GPa based on maskeleynite formation within the plagioclase, kink banding in pyroxenes, and granular recrystallization in the accessory phosphates. Previous Rb-Sr and 40 Ar/ 39 Ar analyses recalculated with modern decay constants yield relatively young ages of 4.16 ± 0.05 Ga and 3.99 ± 0.03 Ga, respectively. However, recent U-Pb analyses of some zircon grains from within the Civet Cat yield an age of 4.45 ± 0.03 Ga. While this is the oldest age for any rock recovered from the Moon, the full age spread of zircon from the Civet Cat range from ca. 4.46 to 4.02 Ga, indicating variable Pb-loss and complicating interpretation of the primary age. Recent atom probe analyses indicate minimal Pb mobilization within the oldest zircon grain from Civet Cat, supporting the interpretation that these ancient zircon ages reflect the age of the norite, rather than an apparent antiquity caused by reverse discordance. To investigate the potential antiquity and deep crustal origin of the Civet Cat norite, we have undertaken high resolution microstructural analyses of the major, minor, and accessory minerals to characterize the primary igneous textures and secondary overprinting by impact and metamorphism. The employed analytical techniques include scanning electron microscope-based electron backscatter diffraction (EBSD) analyses, electron probe microanalyzer (EPMA) chemical analyses, and transmission electron microscopy (TEM) of pyroxene, plagioclase, quartz, zircon, and phosphates.

T M Erickson↗

Electron microscope observations of impact crater debris amongst contaminating particulates on materials surfaces exposed in space in low-Earth orbit

Debris particles extracted from a small sampling region on the leading edge of the Long Duration Exposure Facility (LDEF) spacecraft have been examined by analytical transmission electron microscopy and the elemental frequency observed by energy-dispersive X-ray spectrometry and compared with upper atmosphere (Earth) particle elemental frequency and the average elemental compositions of interplanetary dust particles. A much broader elemental distribution was observed for the exposed spacecraft surface debris milieu. Numerous metal microfragment analyses, particularly aluminum and stainless steel, were compared with scanning electron microscope observations-of impact crater features, and the corresponding elemental spectra on selected LDEF aluminium tray clamps and stainless steel bolts. The compositions and melt features for these impact craters and ejecta have been shown to be consistent with microcrystalline debris fragments in the case of aluminum, and these observations suggest an ever changing debris milieu on exposed surfaces for space craft and space system materials.

Murr, L. E.↗

Mechanical protection of DLC films on fused silica slides

Measurements were made with a new test for improved quantitative estimation of the mechanical protection of thin films on optical materials. The mechanical damage was induced by a sand blasting system using spherical glass beads. Development of the surface damage was measured by the changes in the specular transmission and reflection, and by inspection using a surface profilometer and a scanning electron microscope. The changes in the transmittance versus the duration of sand blasting was measured for uncoated fused silica slides and coated ones. It was determined that the diamond like carbon films double the useful optical lifetime of the fused silica. Theoretical expressions were developed to describe the stages in surface deterioration. Conclusions were obtained for the SiO2 surface mechanism and for the film removal mechanism.

Nir, D.↗

Vestibular receptor cells and signal detection: bioaccelerometers and the hexagonal sampling of two-dimensional signals

The inner ear contains sensory organs which signal changes in head movement. The vestibular sacs, in particular, are sensitive to linear accelerations. Electron microscopic images have revealed the structure of tiny sensory hair bundles, whose mechanical deformation results in the initiation of neuronal activity and the transmission of electrical signals to the brain. The structure of the hair bundles is shown in this paper to be that of the most efficient two-dimensional phased-array signal processors.

NASA Program Space Physiology and Countermeasures↗

Morphometrics of cellular damage in mice testis receiving X-ray and high-energy particle irradiation

Murine tests were exposed to single, low doses of either X-ray, helium, or argon radiation. Animals were sacrificed seventy-two hours later. Testes were fixed for transmission electron microscopy (TEM) and sectioned at either 60 nm for TEM observation or at 2 micron for counting using routine light microscope methods. Counts of the total population of surviving spermatogonia, including all type A cells, intermediate, and type B cells, were taken from tubule cross sections identified as Stage 6 and Stage 1 according to spermatogonial configuration. The surviving fraction of spermatogonia as compared to control, S/S sub o, was calculated for each dose. For both ions and X-rays, there was a rapid decline in survival at dose levels of .10 to .15 Gy in Stage 6 tubules. This was followed by a more gradual decrease in population. At higher doses, 0.30 Gy for argon and 0.80 Gy for helium and X-rays, the cell survival rates declined rapidly. Pre-leptotene spermatocytes in Stage 1 tubules exhibited a different survival curve indicating the extreme radio-sensitivity of type B spermatogonia. Data verify that the seminiferous tubules are composed of a heterogeneous population of cells with different radio-sensitivities and that these differences are manifested even at very low doses.

Sapp, Walter J.↗

Microscopic Observation of Self-Propagation of Calcifying Nanoparticles (Nanobacteria)

Biologists typically define living organisms as carbon and water-based cellular forms with :self-replication" as the fundamental trait of the life process. However, this standard dictionary definition of life does not help scientists to categorize self-replicators like viruses, prions, proteons and artificial life. CNP also named nanobacteria were discovered in early 1990s as about 100 nanometer-sized bacteria-like particles with unique apatite mineral-shells around them, and found to be associated with pathological-calcification related diseases. Although CNP have been isolated and cultured from mammalian blood and diseased calcified tissues, and their biomineralizing properties well established, their biological nature and self-replicating capability have always been severely challenged. The terms "self-replication", "self-assembly" or "self-propagation" have been widely used for all systems including nanomachines, crystals, computer viruses and memes. In a simple taxonomy, all biological and non-biological "self replicators", have been classified into "living" or "nonliving" based on the properties of the systems and the amount of support they require to self-replicate. To enhance our understanding about self-replicating nature of CNP, we have investigated their growth in specific culture conditions using conventional inverted light microscope and BioStation IM, Nikon s latest time-lapse imaging system. Their morphological structure was examined using scanning (SEM) and transmission (TEM) electron microscopy. This present study, in conjunction with previous findings of metabolic activity, antibiotic sensitivity, antibody specificity, morphological aspects and infectivity, all concomitantly validate CNP as living self-replicators.

Mathew, Grace↗

Some surface characteristics and gas interactions of Apollo 14 fines and rock fragments.

Comprehensive survey of the physical surface characteristics of Apollo 14 fines, two fragments of a breccia (14321), and a crystalline rock (14310). The survey was carried out with optical and both scanning and transmission electron microscopy and by studying the adsorption of a variety of gases including nitrogen, hydrogen, and water vapor. Our objective in the optical microscope study was to relate the visible geological and petrological features to the surface properties. Electron microscopy particularly helped relate surface roughness and particle fusion to gas adsorption and pore structure. The fine sample (14163,111) had a surface area of 0.210 sq m/g and a helium density of 2.9 g/cc. Similar values have been observed with breccia fragments. Other observations include physical adsorption of molecular hydrogen at low temperatures and of water vapor at ambient temperatures. It is concluded that these particular lunar materials, while capable of adsorbing water vapor, do not retain it for any significant time at low pressures, nor, under lunar conditions, is there any indication of absorption or penetration.

Cadenhead, D. A.↗