Search NASA⌕ Search

SEARCH · Search NASA

Results for “transport techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Bulk Growth of Wide Band Gap II-VI Compound Semiconductors by Physical Vapor Transport

The mechanism of physical vapor transport of II-VI semiconducting compounds was studied both theoretically, using a one-dimensional diffusion model, as well as experimentally. It was found that the vapor phase stoichiometry is critical in determining the vapor transport rate. The experimental heat treatment methods to control the vapor composition over the starting materials were investigated and the effectiveness of the heat treatments was confirmed by partial pressure measurements using an optical absorption technique. The effect of residual (foreign) gas on the transport rate was also studies theoretically by the diffusion model and confirmed experimentally by the measurements of total pressure and compositions of the residual gas. An in-situ dynamic technique for the transport rate measurements and a further extension of the technique that simultaneously measured the partial pressures and transport rates were performed and, for the first time, the experimentally determined mass fluxes were compared with those calculated, without any adjustable parameters, from the diffusion model. Using the information obtained from the experimental transport rate measurements as guideline high quality bulk crystal of wide band gap II-VI semiconductor were grown from the source materials which undergone the same heat treatment methods. The grown crystals were then extensively characterized with emphasis on the analysis of the crystalline structural defects.

Su, Ching-Hua↗
NASA NTRSDate not supplied

Operational Modal Analysis of the Space Launch System Mobile Launcher on the Crawler Transporter ISVV-010 Rollout

NASA is developing an expendable heavy lift launch vehicle capability, the Space Launch System, to support lunar and deep space exploration. To support this capability, an updated ground infrastructure is required including modifying an existing Mobile Launcher system. The Mobile Launcher is a very large heavy beam/truss steel structure designed to support the Space Launch System during its buildup and integration in the Vehicle Assembly Building, transportation between the Vehicle Assembly Building and launch pad 39B by the Crawler Transporter, and provides the launch platform at the launch pad. As part of the Verification and Validation of the Mobile Launcher and Crawler Transporter, two rollouts of the Mobile Launcher transported by the Crawler Transporter, Integrated System Verification and Validation (ISVV) 005 and 010, have been performed to demonstrate the Crawler Transporter’s ability to transport the Mobile Launcher. ISVV-005 occurred in September 2018 and ISVV-010 occurred in late June 2019. ISVV-005 and ISVV-010 also provided the opportunity to gather data that can be used identify the Mobile Launcher on the Crawler Transporter rollout modal characteristics and refine the estimates of the Artemis I integrated launch vehicle rollout forcing functions. While the rollout environment has historically produced relatively small launch vehicle structural loads for the Saturn/Apollo and Space Shuttle programs in comparison to launch and ascent loads, these relatively small structural loads are inputs to structural fatigue analyses. The same holds true for the Space Launch System. Because the rollout forces acting on the Mobile Launcher and the Crawler Transporter are not directly measurable, Operational Modal Analysis techniques, instead of traditional Experimental Modal Analysis techniques, provide an empirical means to identify the Mobile Launcher on the Crawler Transporter rollout modal characteristics. The ISVV-010 rollout modal characteristics provide important supplemental modal information, which along with the Mobile Launcher modal test that was performed in June 2019 immediately prior to ISVV-010 rollout, combine to reduce uncertainty in the test correlated Mobile Launcher on the Crawler Transporter finite element model. A well test correlated finite element model will play a key role in the Building Block approach the Space Launch System program has implemented as part of its certification process for the Artemis I flight and in refining the Artemis I rollout forcing functions. At the time of the ISVV-005 rollout in September 2018, the Mobile Launcher was still undergoing construction, and therefore its modal characteristics are not directly comparable to those of the Mobile Launcher during the June 2019 Mobile Launcher modal test and subsequent ISVV-010 rollout. Hence the ISVV-005 rollout modal characteristics will not be looked at in this paper. This paper will briefly describe the Mobile Launcher and Crawler Transporter physical characteristics, ISVV-010 rollout data collection, the challenges in implementing Operational Modal Analysis techniques due in part to the Crawler Transporter harmonics, and how these challenges were overcome to obtain the ISVV-010 Mobile Launcher on the Crawler Transporter rollout modal characteristics.

Apollo↗
NASA NTRS2021

Operational Modal Analysis of the Space Launch System Mobile Launcher on the Crawler Transporter ISVV-010 Rollout

NASA is developing an expendable heavy lift launch vehicle capability, the Space Launch System, to support lunar and deep space exploration. To support this capability, an updated ground infrastructure is required including modifying an existing Mobile Launcher system. The Mobile Launcher is a very large heavy beam/truss steel structure designed to support the Space Launch System during its buildup and integration in the Vehicle Assembly Building, transportation between the Vehicle Assembly Building and launch pad 39B by the Crawler Transporter, and provides the launch platform at the launch pad. As part of the Verification and Validation of the Mobile Launcher and Crawler Transporter, two rollouts of the Mobile Launcher transported by the Crawler Transporter, Integrated System Verification and Validation (ISVV) 005 and 010, have been performed to demonstrate the Crawler Transporter’s ability to transport the Mobile Launcher. ISVV-005 occurred in September 2018 and ISVV-010 occurred in late June 2019. ISVV-005 and ISVV-010 also provided the opportunity to gather data that can be used identify the Mobile Launcher on the Crawler Transporter rollout modal characteristics and refine the estimates of the Artemis I integrated launch vehicle rollout forcing functions. While the rollout environment has historically produced relatively small launch vehicle structural loads for the Saturn/Apollo and Space Shuttle programs in comparison to launch and ascent loads, these relatively small structural loads are inputs to structural fatigue analyses. The same holds true for the Space Launch System. Because the rollout forces acting on the Mobile Launcher and the Crawler Transporter are not directly measurable, Operational Modal Analysis techniques, instead of traditional Experimental Modal Analysis techniques, provide an empirical means to identify the Mobile Launcher on the Crawler Transporter rollout modal characteristics. The ISVV-010 rollout modal characteristics provide important supplemental modal information, which along with the Mobile Launcher modal test that was performed in June 2019 immediately prior to ISVV-010 rollout, combine to reduce uncertainty in the test correlated Mobile Launcher on the Crawler Transporter finite element model. A well test correlated finite element model will play a key role in the Building Block approach the Space Launch System program has implemented as part of its certification process for the Artemis I flight and in refining the Artemis I rollout forcing functions. At the time of the ISVV-005 rollout in September 2018, the Mobile Launcher was still undergoing construction, and therefore its modal characteristics are not directly comparable to those of the Mobile Launcher during the June 2019 Mobile Launcher modal test and subsequent ISVV-010 rollout. Hence the ISVV-005 rollout modal characteristics will not be looked at in this paper. This paper will briefly describe the Mobile Launcher and Crawler Transporter physical characteristics, ISVV-010 rollout data collection, the challenges in implementing Operational Modal Analysis techniques due in part to the Crawler Transporter harmonics, and how these challenges were overcome to obtain the ISVV-010 Mobile Launcher on the Crawler Transporter rollout modal characteristics.

Apollo↗
NASA NTRS1994

The permeability of the Antarctic vortex edge

Mixing and cross-vortex mass transport along isentropic surfaces in the lower stratosphere are investigated with a 'contour advection' technique and a semi-Lagrangian transport model for the Antarctic winter of 1993 using analyzed winds from the United Kingdom Meteorological Office data assimilation system. Results from the 'contour advection' technique show that at the vortex edge there exists a potential vorticity (PV) contour that has the smallest lengthening rate. This PV contour is referred to as the 'line of separation' because it essentially separates the inner and outer vortex. The average e-folding time for the lengthening of the 'line of separation' increases monotonically with altitude, ranging from about 7 days on the 350 K isentropic surface to about 105 days on the 500 K isentropic surface. The results also suggest the existence of a transition layer around the 400 K isentropic surface, above which the vortex is nearly completely isolated from the midlatitudes and below which the vortex is less isolated. Results from a semi-Lagrangian transport model with an idealized tracer initially inside the inner vortex show that at 425 K and above virtually no tracer is transported out of the vortex during a 40-day integration starting from July 21, 1993. At 400 K and below a small amount of the tracer is transported out of the vortex while the bulk of the tracer remains confined within the inner vortex.

Chen, Ping↗
NASA NTRS1972

Application of DOT-MORSE coupling to the analysis of three-dimensional SNAP shielding problems

The use of discrete ordinates and Monte Carlo techniques to solve radiation transport problems is discussed. A general discussion of two possible coupling schemes is given for the two methods. The calculation of the reactor radiation scattered from a docked service and command module is used as an example of coupling discrete ordinates (DOT) and Monte Carlo (MORSE) calculations.

Straker, E. A.↗
NASA NTRS1973

Calculation of energy deposition distributions for simple geometries

When high-energy charged particles pass through a thin detector, the ionization energy loss in that detector is subject to fluctuations or straggling which must be considered in interpreting the data. Under many conditions, which depend upon the charge and energy of the incident particle and the detector geometry, the ionization energy lost by the particle is significantly different from the energy deposited in the detector. This problem divides naturally into a calculation of the energy loss that results in excitation and low-energy secondary electrons which do not travel far from their production points, and a calculation of energy loss that results in high-energy secondary electrons which can escape from the detector. The first calculation is performed using a modification of the Vavilov energy loss distribution. A cutoff energy is introduced above which all electrons are ignored and energy transferred to low energy particles is assumed to be equivalent to the energy deposited by them. For the second calculation, the trajectory of the primary particle is considered as a source of secondary high-energy electrons. The electrons from this source are transported using Monte Carlo techniques and multiple scattering theory, and the energy deposited by them in the detector is calculated. The results of the two calculations are then combined to predict the energy deposition distribution. The results of these calculations are used to predict the charge resolution of parallel-plate pulse ionization chambers that are being designed to measure the charge spectrum of heavy nuclei in the galactic cosmic-ray flux.

Watts, J. W., Jr.↗
NASA NTRS1973

Evaluation of effectiveness of various devices for attenuation of trailing vortices based on model tests in a large towing basin

The effectiveness of various candidate aircraft-wing devices for attenuation of trailing vortices generated by large aircraft is evaluated on basis of results of experiments conducted with a 0.03-scale model of a Boeing 747 transport aircraft using a technique developed at the HYDRONAUTICS Ship Model Basin. Emphasis is on the effects produced by these devices in the far-field (up to 8 kilometers downstream of full-scale generating aircraft) where the unaltered vortex-wakes could still be hazardous to small following aircraft. The evaluation is based primarily on quantitative measurements of the respective vortex velocity distributions made by means of hot-film probe traverses in a transverse plane at selected stations downstream. The effects of these altered wakes on rolling moment induced on a small following aircraft are also studied using a modified lifting-surface theory with a synthesized Gates Learjet as a typical example. Lift and drag measurements concurrently obtained in the model tests are used to appraise the effects of each device investigated on the performance characteristics of the generating aircraft.

Kirkman, K. L.↗
NASA NTRS1976

Cryogenic recovery

Because of the low boiling temperature of cryogenic propellants to be used on the Space Shuttle, loss of cryogens from boiloff could become very costly. This paper describes how this shuttle problem is being solved at Kennedy Space Center. Cryogenic losses are categorized relative to the particular cryogenic involved, the Space Shuttle servicing operation causing boiloff and the magnitude of the loss. The techniques under consideration are discussed in detail. These techniques include reclaiming the boiloff by reliquefaction, upgrading the reclaimed boiloff by purification, and interim boiloff storage in metal hydride prior to reprocessing. One of the reliquefaction processes discussed in detail utilizes the cooling effect of venting some of the liquid hydrogen boiloff to provide a simple hydrogen reliquefaction unit. Possible future applications of these cryogenics recovery techniques to industry and transportation systems using liquid hydrogen for energy storage and fuel are also discussed.

Howard, F. S.↗
NASA NTRS1976

OAST Theme Workshop. Volume 3: Working group summary. 8: Structures, dynamics (M-2). A. Statement. B. Technology needs (form 1). C. Priority assessments (form 2)

A technology program on large space structures was defined to respond to common need perceived for five of the six themes. Greatly expanded power, facilities, and communications/sensing requirements appear to demand a new structures technology for construction in space. Requirements to construct huge structural arrays with precision surfaces in space will need creative research efforts to identify practical structural elements and construction techniques. Requirements for advanced transportation structures were defined to respond to the space transportation theme. Because of the criticality of thermal structures to achieve lower cost transportation systems, renewed emphasis on technology in this area is recommended. A second technology needing renewed emphasis is the area of recovery and landing technology structures to permit full reuse of launch vehicle propulsion elements.

Source record↗
NASA NTRS1979

Adaptation of solar sounding rocket payloads for Shuttle

The advent of the Shuttle will permit small solar sounding rocket class payloads to be used for orbital applications as a sub satellite. Solutions to such problems as thermal protection, deployment and retrieval and Shuttle bay storage will be presented. Adapting sounding rocket hardware such as solar telescopes, solar attitude control systems and data acquisition modules along with extending power and control gas requirements is discussed. This resulting hardware may be used either in a sounding rocket or Shuttle payload. This paper will combine the solar sounding rocket quick reaction, low cost techniques with the Shuttle Transportation System.

Windsor, R. M.↗
NASA NTRS1982

Solar energy conversion using surface plasmons for broadband energy transport

A new strategy for efficient solar energy conversion based on parallel processing with surface plasmons is introduced. The approach is unique in identifying: (1) a broadband carrier with suitable range for energy transport, and (2) a technique to extract more energy from the more energetic photons, without sequential losses or unique materials for each frequency band. The aim is to overcome the fundamental losses associated with the broad solar spectrum and to achieve a higher level of spectrum splitting than has been possible in semiconductor systems.

Anderson, L. M.↗
NASA NTRS1984

Determining Training Device Requirements in Army Aviation Systems

A decision making methodology which applies the systems approach to the training problem is discussed. Training is viewed as a total system instead of a collection of individual devices and unrelated techniques. The core of the methodology is the use of optimization techniques such as the transportation algorithm and multiobjective goal programming with training task and training device specific data. The role of computers, especially automated data bases and computer simulation models, in the development of training programs is also discussed. The approach can provide significant training enhancement and cost savings over the more traditional, intuitive form of training development and device requirements process. While given from an aviation perspective, the methodology is equally applicable to other training development efforts.

Poumade, M. L.↗
NASA NTRS1986

A perturbation approach to cosmic ray transients in interplanetary space

A perturbation approach is used to model the linear response of the cosmic ray distribution as a function of perturbations in the solar wind transport parameters. The analytical technique permits examination of the effects of the different solar wind parameters, i.e., velocity, drift velocity and the diffusion tensor, which are additive. Cosmic ray changes in the solar wind are neglected. Variations in the diffusion coefficient and the convection-diffusion equation are applied to describing Forbush decreases and the 11-yr solar cycle variations. The treatment is limited to energies above 100 MeV, yet is considered valid enough to have identified a hysteresis effect in the 11-yr variation, wherein high-energy particles lead low-energy particles to a magnitude that increases with increasing heliocentric distance within the inner heliosphere. The calculations also indicate that the Forbush decreases are a cumulative effect of precipitous precursors accompanied by slow recoveries from travelling solar wind perturbations.

Chih, P. P.↗
NASA NTRS1990

Orbital maneuvering vehicle remote piloting operations

The remote piloting of spacecraft is discussed using the orbital maneuvering vehicle (OMV) as a case in point. Some challenges to remotely piloted operations are listed. Approaches to solving operation problems are discussed for the two major participants in the loop tasks involved. These tasks are the remotely piloted docking task, and the task of ensuring that the rendezvous is successfully completed. Resulting changes to the OMV system are outlined. The outcome of these changes and the approaches taken in the OMV program are presented. Comparisons are drawn between philosophies and techniques used for Space Transportation System rendezvous and proximity operations, and those currently envisioned for OMV. Finally, a few of the lessons learned are summarized.

Veres, Michael L.↗
NASA NTRS1991

Performance Analysis of Garbage Collection and Dynamic Reordering in a Lisp System

Generation based garbage collection and dynamic reordering of objects are two techniques for improving the efficiency of memory management in Lisp and similar dynamic language systems. An analysis of the effect of generation configuration is presented, focusing on the effect of a number of generations and generation capabilities. Analytic timing and survival models are used to represent garbage collection runtime and to derive structural results on its behavior. The survival model provides bounds on the age of objects surviving a garbage collection at a particular level. Empirical results show that execution time is most sensitive to the capacity of the youngest generation. A technique called scanning for transport statistics, for evaluating the effectiveness of reordering independent of main memory size, is presented.

Llames, Rene Lim↗
NASA NTRS1991

A system identification model for adaptive nonlinear control

A system identification model that combines generalized-spline function approximation with a nonlinear control system is described. The complete control system contains three main elements: a nonlinear-inverse-dynamic control law that depends on a comprehensive model of the plant, a state estimator whose outputs drive the control law, and a function approximation scheme that models the system dynamics. The system-identification task, which combines an extended Kalman filter with a function approximator modeled as an artificial neural network, is considered. The results of an application of the identification techniques to a nonlinear transport aircraft model are presented.

Linse, Dennis J.↗