SEARCH · Search NASA

Results for “wind tunnel characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Water tunnel flow visualization and wind tunnel data analysis of the F/A-18

Six degree of freedom studies were utilized to extract a band of yawing and rolling moment coefficients from the F/A-18 aircraft flight records. These were compared with 0.06 scale model data obtained in a 16T wind tunnel facility. The results, indicate the flight test yawing moment data exhibit an improvement over the wind tunnel data to near neutral stability and a significant reduction in lateral stability (again to anear neutral level). These data are consistent with the flight test results since the motion was characterized by a relatively slo departure. Flight tests repeated the slow yaw departure at M 0.3. Only 0.16 scale model wind tunnel data showed levels of lateral stability similar to the flight test results. Accordingly, geometric modifications were investigated on the 0.16 scale model in the 30x60 foot wind tunnel to improve high angle of attack lateral stability.

Erickson, G. E.↗

NASA NTRS1976

Simulation of Flight-Type Engine Fan Noise in the NASA-Lewis 9X15 Anechoic Wind Tunnel

Flight type noise as contrasted to the usual ground static test noise exhibits substantial reductions in the time unsteadiness of tone noise, and in the mean level of tones calculated to be nonpropagating or cut-off. A model fan designed with cuttoff of the fundamental tone was acoustically tested in the anechoic wind tunnel under both static and tunnel flow conditions. The properties that characterize flight type noise were progressively simulated with increasing tunnel flow. The distinctly lobed directivity pattern of propagating rotor/stator interaction modes was also observed. Excess noise attributed to the ingestion of the flow disturbances that prevail near most static test facilities is substantially reduced with tunnel flow.

Heidmann, M. F.↗

NASA NTRS2016

Active Flow Control Using Sweeping Jet Actuators on a Semi-Span Wing Model

Wind tunnel experiments were performed using active flow control on an unswept semispan wing model with a 30% chord trailing edge flap to aid in the selection of actuators for a planned high Reynolds number experiment. Two sweeping jet actuator sizes were investigated to determine the influence of actuator size on the active flow control system efficiency. Sweeping jet actuators with orifice sizes of 1 mm x 2 mm and 2 mm x 4 mm were selected because of the differences in actuator jet sweep angle. The parameters that were varied include actuator momentum, freestream velocity, and trailing edge flap deflection angle. Steady and unsteady pressure data, Particle Image Velocimetry data, and force and moment data were acquired to assess the performance of the two actuators. In addition to the wind tunnel experiments, benchtop studies of the actuators were performed to characterize the jets produced by each actuator. Benchtop investigations of the smaller actuator reveal that the jet exiting the actuator has a reduced sweep angle compared to published data for larger versions of this type of actuator. The larger actuator produces an oscillating jet that attaches to the external di↵user walls at low supply pressures and produces the expected sweep angles. The AFC results using the smaller actuators show that while the actuators can control flow separation, the selected spacing of 3.3 cm may be too large due to the reduced sweep angle. In comparison, the spacing for the larger actuators, 6.6 cm, appears to be optimal for the Mach numbers investigated. Particle Image Velocimetry results are presented and show how the wall jets produced by the actuators cause the flow to attach to the flap surface.

Melton, LaTunia Pack↗

NASA NTRS2021

Unsteady Propagation and Mean Corrections in Open-Jet and Kevlar® Wind Tunnels

Two types of aeroacoustic wind-tunnel test section configurations have been tested in the NASA Langley Quiet Flow Facility. The first is a more traditional open-jet configuration, where test section flow passes unbounded through the facility anechoic chamber. The second is a Kevlar® panel configuration, where a tensioned Kevlar sheet constrains the test section flow from the facility anechoic chamber. For both configurations, acoustic instrumentation is in the surrounding quiescent space. Both configurations are evaluated with a laser-based pulsed acoustic source, which provides unique capability for assessing the facility unsteady acoustic propagation characteristics. Metrics based on the wander and spread of the pulses are evaluated, and show that measurements using Kevlar walls experience dramatically reduced unsteady effects when compared to the open-jet configuration. This leads to a corresponding improvement in coherence between microphones with the Kevlar configuration, by reducing the variation in magnitude and phase differences between channels. Magnitude corrections for propagation through Kevlar as compared to open-jet propagation are calculated. Although limitations in the experimental setup make quantitative analysis difficult, qualitative analysis shows Kevlar magnitude corrections similar to those determined in previous literature. Directivity effects beyond those already present for open-jet configurations are minimal. When compared with the open-jet configuration, the background noise produced by the Kevlar is found to be its one drawback, showing significantly greater levels at high frequencies.

wind tunnel testing, hybrid acoustic tunnel, facil↗

NASA NTRS1994

Experimental studies of transonic flow field near a longitudinally slotted wind tunnel wall

The results of detailed parametric experiments are presented for the near-wall flow field of a longitudinally slotted transonic wind tunnel. Existing data are reevaluated and new data obtained in the Langley 6- by 19-inch Transonic Wind Tunnel are presented and analyzed. In the experiments, researchers systematically investigate many pertinent wall-geometry variables such as the wall openness and the number of slots along with the free stream Mach number and model angle of attack. Flow field surveys on the plane passing through the centerline of the slot were conducted and are presented. The effects of viscosity on the slot flow are considered in the analysis. The present experiments, combined with those of previous investigations, give a more complete physical characterization of the flow near and through the slotted wall of a transonic wind tunnel.

Everhart, Joel L.↗

NASA NTRS1981

Forward velocity effects on fan noise and the influence of inlet aeroacoustic design as measured in the NASA Ames 40 x 80 foot wind tunnel

The inlet radiated noise of a turbofan engine was studied. The principal research objectives were to characterize or suppress such noise with particular regard to its tonal characteristics. The major portion of this research was conducted by using ground-based static testing without simulation of aircraft forward speed or aircraft installation-related aeroacoustic effects.

Holm, R. G.↗

NASA NTRSDate not supplied

Improvements to Calibration Modeling of a Tri-Axial Accelerometer Using Response Surface Methods

Aerodynamic ground test facilities require precision attitude measurements to support fundamental research and aerodynamic vehicle characterization. Accelerometers are used as one solution for measuring test article attitude. Several wind-tunnel facilities experience elevated temperatures during sustained testing of approximately 38°C (100°F) and extremes up to 149°C (300°F). Accelerometer thermal corrections are required to maintain attitude measurement accuracy during elevated temperature tunnel conditions. This manuscript details characterization of non-linear and thermal effects of the Mini/MEMs Tri-Axis Sensor System (MTASS) developed at NASA. Non-linear effects are characterized using a two-axis index head, and temperature effects are characterized using a metallic cube in a thermal chamber. The results show a significant decrease in back-computed residuals for room temperature and elevated temperatures experiments.

Accelerometer↗

NASA NTRSDate not supplied

Improvements to Calibration Modeling of a Tri-Axial Accelerometer Using Response Surface Methods

Accelerometer↗

NASA NTRS2012

Surface and Flow Field Measurements on the FAITH Hill Model

A series of experimental tests, using both qualitative and quantitative techniques, were conducted to characterize both surface and off-surface flow characteristics of an axisymmetric, modified-cosine-shaped, wall-mounted hill named "FAITH" (Fundamental Aero Investigates The Hill). Two separate models were employed: a 6" high, 18" base diameter machined aluminum model that was used for wind tunnel tests and a smaller scale (2" high, 6" base diameter) sintered nylon version that was used in the water channel facility. Wind tunnel and water channel tests were conducted at mean test section speeds of 165 fps (Reynolds Number based on height = 500,000) and 0.1 fps (Reynolds Number of 1000), respectively. The ratio of model height to boundary later height was approximately 3 for both tests. Qualitative techniques that were employed to characterize the complex flow included surface oil flow visualization for the wind tunnel tests, and dye injection for the water channel tests. Quantitative techniques that were employed to characterize the flow included Cobra Probe to determine point-wise steady and unsteady 3D velocities, Particle Image Velocimetry (PIV) to determine 3D velocities and turbulence statistics along specified planes, Pressure Sensitive Paint (PSP) to determine mean surface pressures, and Fringe Imaging Skin Friction (FISF) to determine surface skin friction (magnitude and direction). This initial report summarizes the experimental set-up, techniques used, data acquired and describes some details of the dataset that is being constructed for use by other researchers, especially the CFD community. Subsequent reports will discuss the data and their interpretation in more detail

Bell, James H.↗

NASA NTRS2023

Experimental Characterization of the Space Launch System Block 1B Liftoff and Transition Environment

A wind tunnel test was conducted at the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel to evaluate the liftoff and transition flow environment of the Space Launch System Block 1B launch vehicles and tower interference effects with the newly designed Mobile Launcher 2. This test leveraged several unique diagnostic capabilities, including eight distributed force and moment measurements on the launch tower tiers, new umbilical and crew access arm configurations, and unsteady pressure acquisition on the rocket nose in the cargo configuration. The tower loading revealed a strong impact of the SLS vehicle height on force coefficients for individual tiers. Although the umbilicals produced weak influence on the loading on both vehicle and launch tower, unsteady pressure measurements revealed a slight increase in fundamental pressure oscillation frequency at specific wind azimuth directions. Multimodal flow states were observed in the gap flow between the vehicle and solid rocket boosters, producing different load profiles along the vehicle that are now incorporated in the vehicle database. This phenomenon was investigated using time-series measurements of forces as well as tufts and smoke flow visualization.

Lee J Mears↗

NASA NTRS2023

Experimental Characterization of the Space Launch System Block 1B Liftoff and Transition Environment

SLS↗

NASA NTRSDate not supplied

Shock-Wave/Boundary-Layer Interaction (SWBLI) Experiments in the Presence of Transition-to-Turbulence on a Flat Plate Model in the NASA LaRC 31-Inch Mach 10 Air Tunnel

Historically, there have been a limited number of studies involving Transitional Shock-Wave/Boundary-Layer Interactions (XSWBLI) in hypersonic flows, the majority of which have been performed at Mach Numbers of 7.5 and below. Additionally, there have been even fewer such experiments which incorporate non-intrusive and optical diagnostics. NASA Langley Research Center (NASA LaRC), in collaboration with The University of Texas at San Antonio (UTSA) and The University of Tennessee Space Institute (UTSI), is currently planning and preparing for a series of experimental aerodynamic tests using the NASA LaRC 31-inch Mach 10 Air Tunnel. The experiments will primarily focus on studying the dynamics of Shock-Wave/Boundary-Layer Interactions (SWBLI) in the presence of transition (XSWBLI) and turbulence (SWTBLI) on a large, flat plate model at a freestream Mach number of 10. Besides continued interest in understanding the flow at high Mach numbers, executing such tests at Mach 10 avoids some known concerns and will aid in solving new problems. XSWBLI are a highly unsteady phenomena and the generation of XSWBLI at lower Mach numbers can prove to be a significant challenge. This concern will be somewhat mitigated in the Mach 10 flow, as boundary layers become increasingly stabilized, but some difficulty in achieving transition is still expected. Modelling SWBLI in the presence of transitional and turbulent boundary layers has also proven to be difficult, so a high-Mach number experiment which applies non-intrusive and optical diagnostics will aid in solving a unique problem as well as advancing the understanding and characterization of an aerodynamic surface at Mach 10.The NASA LaRC 31-inch Wind Tunnel incorporates a test section having a cross-section of 31-inches × 31-inches and provides optical access to the test section via three (3) ultra-violet (UV) transmitting windows on the top, side, and bottom. The Mach 10 operating conditions will consist of pressures (P0) ranging from 2.4 to 10MPa (348 to 1,450 psi) at a temperature (T0) of 1,000 K (1,800 °R). The NASA LaRC 31-inch wind tunnel will deliver 1-minute blow-down runs, of which 30-45 seconds will be consumed to reach the aforementioned test conditions. The pump down time between runs will be approximately 45-60 minutes, which will provide for 6-10 test runs per day over the course of a weeklong entry. The proposed flat plate model will be constructed of stainless steel with geometry consisting of a10-inch × 30-inch upper surface and a 2-inch thickness. The model will be designed to support multiple leading-edge inserts in order to examine blunt, round, and sharp leading edges at Mach 10. Adjustments will be made to manage boundary layer thickness as well as the strength and size of the shock interaction region for each test. Measurements and diagnostics will be performed though high-speed Schlieren, on-body high-speed pressure transducers, IR thermography, and oil flow visualization. Hypersonic vehicle applications have and will continue to emerge at the forefront of aerospace. The NASA-UTSA-UTSI team realizes the value of characterizing SWBLI, XSWBLI, and SWTBLI behaviors well beyond single-digit hypersonic Mach numbers. As hypersonic vehicle speed capabilities continue to increase, measurement and diagnostic methods for Mach numbers of 10 and beyond will provide the foundation for a firm understanding of flow field behavior which will directly influence the advancement of technologies towards the design and manufacturing of high-speed aerodynamic surfaces, controls, thermal protection systems, acoustic treatments, and structural components. The use of non-intrusive and optical diagnostic methods in such experimentation is pivotal in developing the visualization and empirical data necessary to advance the aforementioned technology areas.

Shockwave/Boundary-Layer Interactions↗

NASA NTRS2016

Synthesis, Characterization and Evaluation of Urethane Co-Oligomers Containing Pendant Fluoroalkyl Ether Groups

Coatings with the ability to minimize adhesion of insect residue and other debris are of great interest for future aircraft. These aircraft will exhibit increased fuel efficiency by maintaining natural laminar flow over greater wing chord distances. Successful coatings will mitigate the adhesion of debris on laminar flow surfaces that could cause a premature transition to turbulent flow. The use of surface modifying agents (SMA) that thermodynamically orient towards the air side of a coating can provide specific surface chemistry that may lead to a reduction of contaminate adhesion. Aluminum surfaces coated with urethane co-oligomers containing various amounts of pendant fluoroalkyl ether groups were prepared, characterized and tested for their abhesive properties. The coated surfaces were subjected to controlled impacts with wingless fruit flies (drosophila melanogaster) using both a benchtop wind tunnel and a larger-scale wind tunnel test facility. Insect impacts were recorded and analyzed using high-speed digital photography and the remaining residues characterized using optical surface profilometry and compared to that of an aluminum control. It was determined that using fluorinated oligomers to chemically modify coating surfaces altered the adhesion properties relative to the adhesion of insect residues to the surface.

Jereme R Doss↗

NASA NTRS1992

Experimental results for a hypersonic nozzle/afterbody flow field

The flow field created by the interaction of a single-expansion-ramp-nozzle (SERN) flow with a hypersonic external stream has been experimentally characterized using a generic nozzle/afterbody model in the 3.5-foot hypersonic wind tunnel of the NASA Ames Research Center. The presented results include oil-flow and shadowgraph flow visualization photographs, afterbody surface-pressure distributions, boundary layer rake measurements, and Preston-tube skin-friction measurements. The design, construction, and operation of the model was found to be successful. Surface oil-flow patterns show that the jet-plume flow attaches to the afterbody surface at jet pressure ratios between 154 and 234. The oil flow also shows the pattern of lines where the jet flow separates from the ramp, apparently as a result of interaction of the jet-plume internal shock wave with the ramp boundary layer.

Spaid, Frank W.↗

NASA NTRS2014

An Experimental Investigation of the 30P30N Multi-Element High-Lift Airfoil

High-lift devices often generate an unsteady flow field producing both broadband and tonal noise which radiates from the aircraft. In particular, the leading edge slat is often a dominant contributor to the noise signature. An experimental study of a simplified unswept high-lift configuration, the 30P30N, has been conducted to understand and identify the various flow-induced noise sources around the slat. Closed-wall wind tunnel tests are performed in the Florida State Aeroacoustic Tunnel (FSAT) to characterize the slat cove flow field using a combination of surface and off-body measurements. Mean surface pressures compare well with numerical predictions for the free-air configuration. Consistent with previous measurements and computations for 2D high-lift configurations, the frequency spectra of unsteady surface pressures on the slat surface display several narrowband peaks that decrease in strength as the angle of attack is increased. At positive angles of attack, there are four prominent peaks. The three higher frequency peaks correspond, approximately, to a harmonic sequence related to a feedback resonance involving unstable disturbances in the slat cove shear layer. The Strouhal numbers associated with these three peaks are nearly insensitive to the range of flow speeds (41-58 m/s) and the angles of attack tested (3-8.5 degrees). The first narrow-band peak has an order of magnitude lower frequency than the remaining peaks and displays noticeable sensitivity to the angle of attack. Stereoscopic particle image velocimetry (SPIV) measurements provide supplementary information about the shear layer characteristics and turbulence statistics that may be used for validating numerical simulations.

Pascioni, Kyle A.↗

NASA NTRSDate not supplied

Predicting Orion Launch Abort Acoustics

Computational fluid dynamics (CFD) scale-resolving simulations were performed to help assess the Orion launch abort system’s vibro-acoustic environment in collaboration with the Orion Loads and Dynamics team at the Johnson Space Center (JSC). The primary objectives are to establish best practices and to validate CFD predictions for surface fluctuating pressure spectra with ground, wind tunnel, and flight test data. Excellent agreement is obtained between CFD predictions by the Cartesian adaptive mesh refinement (AMR) module of the Launch, Ascent, and Vehicle Aerodynamics (LAVA) solver and measurements from a ground test representative of the start of a pad abort scenario, and with measurements from a wind tunnel test case corresponding to a transonic, high total angle of attack ascent abort scenario. A simplified (static and at rest) simulation of a pad abort flight test shows good agreement with the flight data, whereas a more costly simulation where the vehicle is accelerating relative to the ground from rest to Mach 0.4 shows consistent over-prediction of the spectra. Simulation results for a supersonic ascent abort flight test are in reasonable agreement with the measurements, but show larger excursions in regions where non-linear interactions between the plume turbulence, shocks, and turbulent boundary layer are strongest – likely due to CFD modeling assumptions, the effect of which are discussed. Overall, the CFD results demonstrate that scale-resolving simulation methodologies like the one presented can help characterize full-scale launch abort vehicle near-field noise and can complement wind tunnel, ground and flight tests by providing trends and reducing uncertainty for scenarios that cannot or are not planned to be tested.

Orion↗

NASA NTRS2001

Response Surface Modeling Using Multivariate Orthogonal Functions

A nonlinear modeling technique was used to characterize response surfaces for non-dimensional longitudinal aerodynamic force and moment coefficients, based on wind tunnel data from a commercial jet transport model. Data were collected using two experimental procedures - one based on modem design of experiments (MDOE), and one using a classical one factor at a time (OFAT) approach. The nonlinear modeling technique used multivariate orthogonal functions generated from the independent variable data as modeling functions in a least squares context to characterize the response surfaces. Model terms were selected automatically using a prediction error metric. Prediction error bounds computed from the modeling data alone were found to be- a good measure of actual prediction error for prediction points within the inference space. Root-mean-square model fit error and prediction error were less than 4 percent of the mean response value in all cases. Efficacy and prediction performance of the response surface models identified from both MDOE and OFAT experiments were investigated.

Morelli, Eugene A.↗

NASA NTRSDate not supplied

Evaluation of Response Surface Experiment Designs for Distributed Propulsion Aircraft Aero-Propulsive Modeling

Modern distributed hybrid and electric propulsion aircraft, including vertical, short, and conventional takeoff and landing configurations, exhibit significant aero-propulsive complexity and a large number of interacting test factors. This paper presents the development and evaluation of experiment designs for aero-propulsive characterization of distributed propulsion aircraft. Five different foundational response surface designs are evaluated to inform the development of two sequential design approaches tailored to complex aircraft aerodynamic characterization experiments. The first approach, which builds on sequential face-centered central composite designs, has been used previously to develop aero-propulsive models for complex aircraft using wind tunnel testing. The second approach is a new design strategy leveraging a regular I-optimal and nested I-optimal design that was developed for this study. The two sequential design strategies are compared for experiments with a large number of test factors using pre-experiment design evaluation metrics, as well as modeling results obtained from simulated wind tunnel data for the NASA LA-8 aircraft. The design evaluation metrics show that the sequential I-optimal base design has higher statistical power, lower correlation among candidate regressors, lower prediction variance, and more precise parameter estimates. The simulated wind tunnel experiments conducted using each design reveal that the sequential I-optimal base design has better predictive capability with fewer test points. The experiment design and evaluation procedures are described in detail to inform future aerodynamic characterization experiments for complex aircraft.

design of experiments↗