Search NASA⌕ Search

SEARCH · Search NASA

Results for “Capacitance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Charge fluctuations for particles on a surface exposed to plasma

We develop a stochastic model for the charge fluctuations on a microscopic dust particle resting on a surface exposed to plasma. We find in steady state that the fluctuations are normally distributed with a standard deviation that is proportional to (CT{sub e}){sup 1/2}, where C is the particle-surface capacitance and T{sub e} is the plasma electron temperature. The time for an initially uncharged ensemble of particles to reach the steady state distribution is directly proportional to CT{sub e}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Barrier height of Pt-In{sub x}Ga{sub 1-x}N (0{<=}x{<=}0.5) nanowire Schottky diodes

The barrier height of Schottky diodes made on In{sub x}Ga{sub 1-x}N nanowires have been determined from capacitance-voltage measurements. The nanowires were grown undoped on n-type (001) silicon substrates by plasma-assisted molecular beam epitaxy. The length, diameter and density of the nanowires are {approx}1 {mu}m, 20 nm, and 1x10{sup 11} cm{sup -2}. The Schottky contact was made on the top surface of the nanowires with Pt after planarizing with parylene. The measured barrier height {Phi}{sub B} varies from 1.4 eV (GaN) to 0.44 eV (In{sub 0.5}Ga{sub 0.5}N) and agrees well with the ideal barrier heights in the Schottky limit.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Fine tuning of phase qubit parameters for optimization of fast single-pulse readout

We analyze a two-level quantum system, describing the phase qubit, during a single-pulse readout process by a numerical solution of the time-dependent Schroedinger equation. It has been demonstrated that the readout error has a minimum for certain values of the system's basic parameters. In particular, the optimization of the qubit capacitance and the readout pulse shape leads to significant reduction in the readout error. It is shown that in an ideal case the fidelity can be increased to almost 97% for 2 ns pulse duration and to 96% for 1 ns pulse duration.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Direct determination of flat-band voltage for metal/high {kappa} oxide/semiconductor heterointerfaces by electric-field-induced second-harmonic generation

We have employed electric-field-induced second-harmonic (EFISH) generation to determine the flat-band voltage (V{sub FB}) of Cr/ALD-Al{sub 2}O{sub 3}/MBE-HfO{sub 2}/n-Si (001) MOS structure. Due to the phase sensitivity of EFISH signal to the electric field in the space charge region, the V{sub FB} of -1.20{+-}0.07 V was determined by analyzing the relative phase change in the EFISH signal as a function of the applied gate voltage. The obtained value is in good agreement with that estimated by the capacitance-voltage measurement. This study demonstrated an all-optical technique to directly determine the flat-band voltage for the high {kappa} oxide/Si heterointerfaces.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Molecular beam deposition of Al{sub 2}O{sub 3} on p-Ge(001)/Ge{sub 0.95}Sn{sub 0.05} heterostructure and impact of a Ge-cap interfacial layer

We investigated the molecular beam deposition of Al{sub 2}O{sub 3} on Ge{sub 0.95}Sn{sub 0.05} surface with and without an ultra thin Ge cap layer in between. We first studied the atomic configuration of both Ge{sub 1-x}Sn{sub x} and Ge/Ge{sub 1-x}Sn{sub x} surfaces after deoxidation by reflection high-energy electron diffraction and resulted, respectively, in a c(4x2) and (2x1) surface reconstructions. After in situ deposition of an Al{sub 2}O{sub 3} high-{kappa} gate dielectric we evidenced using time-of-flight secondary ion mass spectroscopy analyses that Sn diffusion was at the origin of high leakage current densities in the Ge{sub 1-x}Sn{sub x}/Al{sub 2}O{sub 3} gate stack. This damage could be avoided by inserting a thin 5-nm-thick Ge cap between the oxide and the Ge{sub 1-x}Sn{sub x} layer. Finally, metal-oxide-semiconductor capacitors on the Ge capped sample showed well-behaved capacitance-voltage (C-V) characteristics with interface trap density (D{sub it}) in the range of 10{sup 12} eV{sup -1} cm{sup -2} in mid gap and higher close to the valence band edge.

36 MATERIALS SCIENCE↗

Neutron doping effects in epitaxially laterally overgrown n-GaN

Thermal neutron irradiation and annealing effects were studied for undoped n-GaN prepared by epitaxial lateral overgrowth (ELOG). Electron beam induced current (EBIC) imaging and profiling prior to irradiation showed that the residual donor doping in our ELOG samples was about three times higher in the high-dislocation-density ELOG wing than in the low-dislocation-density ELOG window regions. Irradiation with thermal neutrons and subsequent annealing led to greatly improved doping uniformity, as evidenced by EBIC imaging. The neutron transmutation doping avoids the anisotropy of donor incorporation efficiency for different planes during ELOG and provides a uniform doping environment. Capacitance-voltage profiling on such samples showed the presence of electrically active centers with concentration close to the concentration of Ge donors produced by Ga interaction with thermal neutrons.

36 MATERIALS SCIENCE↗

Role of stable and metastable Mg-H complexes in p-type GaN for cw blue laser diodes

Secondary ion mass spectroscopy (SIMS) and capacitance-voltage measurements were combined to thoroughly study Mg doping in GaN layers grown by metal organic vapor phase epitaxy. First we found that the Mg steady-state incorporation regime occurs for a surface coverage of 0.3 monolayer. Additionally SIMS indicates that H incorporates proportionally with Mg until a certain [Mg] where [H] saturates. After thermal activation, [H] while being much lower still scales with [Mg]. These results suggest that H combines with Mg to form two different types of Mg-H complexes: a metastable one leading to the Mg acceptor after annealing, the other one (dominating at high [Mg]) being stable and electrically inactive. The obtained results allowed us optimizing doping conditions for blue laser diodes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Formation of a semi-insulating layer in n-type 4H-SiC by electron irradiation

Electron irradiation has been applied to the formation of a semi-insulating 4H-SiC(0001) layer. The resistivity of the semi-insulating layer, which was irradiated with a fluence of 1.9 x 10{sup 18} cm{sup -2} at 400 keV, exceeded 10{sup 10{Omega}} cm at room temperature. From capacitance-voltage characteristics of Schottky structure, the depth of the semi-insulating layer was estimated to be 10 {mu}m, indicating that the whole region of lightly-doped n-type epilayer was converted to the semi-insulating layer by electron irradiation. The semi-insulating property can be ascribed to electron trapping at the Z{sub 1/2} and EH{sub 6/7} centers generated by electron irradiation. The threshold energy for the generation of Z{sub 1/2} center was about 100 keV.

36 MATERIALS SCIENCE↗

Structural analysis and electrical properties of pure Ge{sub 3}N{sub 4} dielectric layers formed by an atmospheric-pressure nitrogen plasma

Pure germanium nitride (Ge{sub 3}N{sub 4}) thin films were successfully formed on n-type Ge (111) substrate using an atmospheric-pressure (AP) nitrogen plasma. Their film structures and electrical properties were then examined in detail. Synchrotron radiation photoelectron spectroscopy clearly revealed that the Ge{sub 3}N{sub 4} thin films formed by AP plasma had superior oxidative resistance compared to those made using conventional plasma techniques. Films fabricated at 500 deg. C showed only minor post-oxidation, even after exposure to air, which is a potentially very useful feature for passivation layers at high-permittivity (high-k) dielectric film-Ge interfaces. The films also showed excellent electrical properties. Capacitance-voltage measurements revealed no hysteresis or kinks, indicating that the trap-state density was low at the Ge{sub 3}N{sub 4}-Ge interface. The leakage current density is also lower than in films fabricated using other plasma systems. Direct-tunneling current simulations revealed that the effective tunneling mass increased due to the formation of high-quality Ge{sub 3}N{sub 4} thin films, resulting in superior leakage current. These results suggest that our nitridation technique would show major benefits in Ge field-effect transistors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electronic states at the interface between indium tin oxide and silicon

Electronic properties and thermal stability of interfacial states between indium tin oxide (ITO) and monocrystalline silicon (Si) have been investigated. ITO films with thicknesses of about 300 nm were deposited by dc magnetron sputtering on n- and p-type (100) Si at room temperature. The samples were then annealed for 30 min at different temperatures in the range 100-600 deg. C, and the ITO-Si junction was found to exhibit rectifying behavior. Current-voltage (IV), capacitance-voltage (CV), and deep-level transient spectroscopy (DLTS) measurements have been used to electrically characterize the ITO-Si interface. DLTS measurements on p-type Si samples reveal a dominant hole trap at around 0.37 eV above the valence band edge. In the n-type samples, a broad band of electron traps occur in the range 0.1-0.2 eV below the conduction band edge. These electron traps display wide DLTS peaks, indicating a band of electronic energy levels rather than well-defined states originating from isolated point defects. All the traps in both the p- and n-type samples are found to be located near the ITO-Si interface. Investigations of the thermal stability of the observed electronic states show that the dominant hole trap anneal out after 30 min at 250 deg. C, while the dominant electron traps can be stable up to 500 deg. C. IV and DLTS measurements demonstrate a clear correlation between the annealing of the dominant electronic states and increase in the junction rectification.

36 MATERIALS SCIENCE↗

Phase, Dielectric and Ferroelectric Properties of Microwave Sintered La and Ca Modified BaTiO{sub 3} Ceramics

Lanthanum and calcium modified barium titanate, Ba{sub (1-x)}La{sub x}Ti{sub (1-x/4)}O{sub 3}/BLT and Ba({sub 1-x})Ca{sub x}TiO{sub 3}/BCT, where x = 0.02, ferroelectric ceramic samples were synthesized in single perovskite phase by microwave processing technique. Sintering temperature was optimized at 1100 deg. C for 1h. Presence of pore free micron size uniform grains suggested the advantage of using microwave sintering process. Transition temperature (T{sub c}) decreases with the substitution of La content in BT system. Temperature coefficient of capacitance is negligible from RT temperature to 75 deg. C for BLT ceramic samples. Polarization vs. electric field (P-E) hysteresis loop study confirms the ferroelectric nature of the modified BT ceramic samples.

36 MATERIALS SCIENCE↗

Electrical properties of atomic layer deposited aluminum oxide on gallium nitride

We report on our investigation of the electrical properties of metal/Al{sub 2}O{sub 3}/GaN metal-insulator-semiconductor capacitors. We determined the conduction band offset and interface charge density of the alumina/GaN interface by analyzing the capacitance-voltage characteristics of atomic layer deposited Al{sub 2}O{sub 3} films on GaN substrates. The conduction band offset at the Al{sub 2}O{sub 3}/GaN interface was calculated to be 2.13 eV, in agreement with theoretical predications. A non-zero field of 0.93 MV/cm in the oxide under flat-band conditions in the GaN was inferred, which we attribute to a fixed net positive charge density of magnitude 4.60 x 10{sup 12 }cm{sup -2} at the Al{sub 2}O{sub 3}/GaN interface. We provide hypotheses to explain the origin of this charge by analyzing the energy band line-up.

36 MATERIALS SCIENCE↗

Characteristics of Various Photodiode Structures in CMOS Technology with Monolithic Signal Processing Electronics

Monolithic optical sensor with readout electronics are needed in optical communication, medical imaging and scintillator based gamma spectroscopy system. This paper presents the design of three different CMOS photodiode test structures and two readout channels in a commercial CMOS technology catering to the need of nuclear instrumentation. The three photodiode structures each of 1 mm{sup 2} with readout electronics are fabricated in 0.35 um, 4 metal, double poly, N-well CMOS process. These photodiode structures are based on available P-N junction of standard CMOS process i.e. N-well/P-substrate, P+/N-well/P-substrate and inter-digitized P+/N-well/P-substrate. The comparisons of typical characteristics among three fabricated photo sensors are reported in terms of spectral sensitivity, dark current and junction capacitance. Among the three photodiode structures N-well/P-substrate photodiode shows higher spectral sensitivity compared to the other two photodiode structures. The inter-digitized P+/N-well/P-substrate structure has enhanced blue response compared to N-well/P-substrate and P+/N-well/P-substrate photodiode. Design and test results of monolithic readout electronics, for three different CMOS photodiode structures for application related to nuclear instrumentation, are also reported.

36 MATERIALS SCIENCE↗

Characterization of high-{kappa} LaLuO{sub 3} thin film grown on AlGaN/GaN heterostructure by molecular beam deposition

We report the study of high-dielectric-constant (high-{kappa}) dielectric LaLuO{sub 3} (LLO) thin film that is grown on AlGaN/GaN heterostructure by molecular beam deposition (MBD). The physical properties of LLO on AlGaN/GaN heterostrucure have been investigated with atomic force microscopy, x-ray photoelectron spectroscopy, and TEM. It is revealed that the MBD-grown 16 nm-thick LLO film is polycrystalline with a thin ({approx}2 nm) amorphous transition layer at the LLO/GaN interface. The bandgap of LLO is derived as 5.3 {+-} 0.04 eV from O1s energy loss spectrum. Capacitance-voltage (C-V) characteristics of a Ni-Au/LLO/III-nitride metal-insulator-semiconductor diode exhibit small frequency dispersion (<2%) and reveal a high effective dielectric constant of {approx}28 for the LLO film. The LLO layer is shown to be effective in suppressing the reverse and forward leakage current in the MIS diode. In particular, the MIS diode forward current is reduced by 7 orders of magnitude at a forward bias of 1 V compared to a conventional Ni-Au/III-nitride Schottky diode.

36 MATERIALS SCIENCE↗

Secondary Electron Emission from Dust and Its Effect on Charging

Hydrogen plasma is produced in a plasma chamber by striking discharge between incandescent tungsten filaments and the permanent magnetic cage [1], which is grounded. The magnetic cage has a full line cusped magnetic field geometry used to confine the plasma elements. A cylindrical Langmuir probe is used to study the plasma parameters in various discharge conditions. The charge accumulated on the dust particles is calculated using the capacitance model and the dust current is measured by the combination of a Faraday cup and an electrometer at different discharge conditions. It is found Secondary electron emission from dust having low emission yield effects the charging of dust particles in presence of high energetic electrons.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A gain and bandwidth enhanced transimpedance preamplifier for Fourier-transform ion cyclotron resonance mass spectrometry

The nature of the ion signal from a 12-T Fourier-transform ion cyclotron resonance mass spectrometer and the electronic noise were studied to further understand the electronic detection limit. At minimal cost, a new transimpedance preamplifier was designed, computer simulated, built, and tested. The preamplifier design pushes the electronic signal-to-noise performance at room temperature to the limit, because of its enhanced tolerance of the capacitance of the detection device, lower intrinsic noise, and larger flat mid-band gain (input current noise spectral density of around 1 pA/{radical}(Hz) when the transimpedance is about 85 dB{Omega}). The designed preamplifier has a bandwidth of {approx}3 kHz to 10 MHz, which corresponds to the mass-to-charge ratio, m/z, of approximately 18 to 61 k at 12 T. The transimpedance and the bandwidth can be easily adjusted by changing the value of passive components. The feedback limitation of the circuit is discussed. With the maximum possible transimpedance of 5.3 M{Omega} when using an 0402 surface mount resistor, the preamplifier was estimated to be able to detect {approx}110 charges in a single scan.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Mechanical vibrations induced resonant breakdown of the Coulomb blockade

Influence of forced mechanical vibrations of a suspended single-electron transistor on electron tunneling through the quantum dot limited by the Coulomb blockade is investigated. It is shown that mechanical oscillations of the quantum dot lead to the Coulomb blockade breakdown, shown in sharp resonant peaks in the transistor conductance dependence on the excitation frequency at values corresponding to the mechanical oscillations eigen modes. The observed effect is presumably connected with oscillations of the mutual electrical capacitances between the quantum dot and surrounding electrodes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An in-vacuum x-ray diffraction microscope for use in the 0.7-2.9 keV range

A dedicated in-vacuum coherent x-ray diffraction microscope was installed at the 2-ID-B beamline of the Advanced Photon Source for use with 0.7-2.9 keV x-rays. The instrument can accommodate three common implementations of diffractive imaging; plane wave illumination; defocused-probe (Fresnel diffractive imaging) and scanning (ptychography) using either a pinhole, focused or defocused probe. The microscope design includes active feedback to limit motion of the optics with respect to the sample. Upper bounds on the relative optics-to-sample displacement have been measured to be 5.8 nm(v) and 4.4 nm(h) rms/h using capacitance micrometry and 27 nm/h using x-ray point projection imaging. The stability of the measurement platform and in-vacuum operation allows for long exposure times, high signal-to-noise and large dynamic range two-dimensional intensity measurements to be acquired. Finally, we illustrate the microscope's stability with a recent experimental result.

43 PARTICLE ACCELERATORS↗