Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Calculation of strain compensation thickness for III–V semiconductor quantum dot superlattices

Models based on continuum elasticity theory are discussed to calculate the necessary thickness of a strain compensation (SC) layer for a superlattice (SL) of strained quantum wells (QW) or quantum dots (QD). These models are then expanded to cover material systems (substrates, QW or QD, and SC) composed of AlP, AlAs, AlSb, GaP, GaAs, GaSb, InP, InAs, or InSb, as well as the ternary, quaternary, and higher order material alloys possible in the Al/Ga/In/P/As/Sb systems. SC thickness calculation methods were compared against dynamical scattering simulations and experimental X-ray diffraction measurements of the InAs/GaP/GaAs QD/SC/Substrate superlattices of varying SC thickness. Based on the reduced (but not eliminated) strain present, a further modified strain compensation thickness is calculated to maximize the number of SL repeat units before the onset of misfit dislocations is also calculated. In conclusion, these models have been assembled into a free application on nanoHUB for use by the community.

36 MATERIALS SCIENCE↗

Characterization of radiation damage in 3D printed SiC

The SiC fuel matrix for advanced gas-cooled high temperature reactors as part of the Transformational Challenge Reactor program serves as the fuel particle container structure, a barrier to fission gas release, and a heat transfer medium. Its performance is particularly important because the fuel matrix must demonstrate good structural stability and thermal behaviors. An additive manufacturing methodology combining a binder jet 3D printing process with chemical vapor infiltration (CVI) for the production of SiC was recently developed. In this study, post irradiation examination by transmission electron microscopy shows that defect accumulation within the printed particles is very similar to other forms of high-purity SiC. However, damage accumulation was not directly observed in the CVI matrix because black spot damage and dislocation loops are difficult to image within the nanoscale highly faulted CVI matrix and because interstitial defects may rapidly annihilate at the stacking faults. Therefore, electron energy loss spectroscopy (EELS) analysis was used to analyze defect swelling in both the printed particles and the CVI matrix. The EELS analysis helped reveal that the radiation-induced swelling in the CVI matrix is similar to that of the printed SiC particles. This work shows that 3D printed SiC has behavior that is comparable to SiC processed by other means and that 3D printing could serve as a suitable processing technique for high-purity SiC for nuclear applications.

36 MATERIALS SCIENCE↗

Synergies between H, He and radiation damage in dual and triple ion irradiation of candidate fusion blanket materials

Three ferritic/martensitic alloys were studied to understand the synergistic effect between single ion beam (Fe 2+ ), dual ion beam (Fe 2+ +He 2+ and Fe 2+ +H + ), and triple ion beam (Fe 2+ +He 2+ +H + ) irradiations on cavity evolution. A commercial alloy, F82H, a castable nanostructured alloy, CNA3, and a high purity model alloy, Fe8Cr2W, were irradiated at 400°C to 600°C to a damage level of 50 dpa at a damage rate of 1 × 10 –3 dpa/s with He and H injection rates of 10 and 40 appm/dpa, respectively. Post-irradiation characterization via bright field transmission electron microscopy and high-angle annular dark-field scanning transmission electron microscopy was performed on all irradiated conditions to characterize the cavity size distribution and determine the effects of H/He injection on cavity microstructure. In all three alloys, hydrogen co-injection with helium resulted in an increased cavity number density and maximum cavity size, producing an increase in swelling over that from helium injection alone. Swelling in F82H appears to peak between 450°C and 500°C. At 600°C, swelling was minimal and cavities of high density and small size were confined to grain boundaries and dislocations while at 400°C, swelling is also low with a nearly homogeneous, high density, distribution of very small cavities throughout. Swelling was least in the commercial alloy F82H due to the high sink strength. The CNA3 alloy underwent dissolution of precipitates that lowered the sink strength and resulted in higher swelling than F82H, but less than the model alloy. Electron energy loss spectroscopy (EELS) elemental mapping revealed hydrogen forming a halo-like structure about the periphery of the cavities and helium residing within the cavities themselves. Finally, this observation suggests that hydrogen reduces the surface energy of helium-filled cavities which results in both increased cavity number density and cavity size in triple beam irradiation over dual beam irradiation.

36 MATERIALS SCIENCE↗

Size effect, critical resolved shear stress, stacking fault energy, and solid solution strengthening in the CrMnFeCoNi high-entropy alloy

High-entropy alloys (HEAs) comprise a novel class of scientifically and technologically interesting materials. Among these, equatomic CrMnFeCoNi with the face-centered cubic (FCC) structure is noteworthy because its ductility and strength increase with decreasing temperature while maintaining outstanding fracture toughness at cryogenic temperatures. Here we report for the first time by single crystal micropillar compression that its bulk room temperature critical resolved shear stress (CRSS) is ~33–43MPa, ~10 times higher than that of pure nickel. CRSS depends on pillar size with an inverse power-law scaling exponent of –0.63 independent of orientation. Planar ½<110>{111} dislocations dissociate into Shockley partials whose separations range from ~3.5–4.5nm near the screw orientation to ~5–8nm near the edge, yielding a stacking fault energy of 30±5mJ/m2. Dislocations are smoothly curved without any preferred line orientation indicating no significant anisotropy in mobilities of edge and screw segments. The shear-modulus-normalized CRSS of the HEA is not exceptionally high compared to those of certain concentrated binary FCC solid solutions. Its rough magnitude calculated using the Fleischer/Labusch models corresponds to that of a hypothetical binary with the elastic constants of our HEA, solute concentrations of 20–50 at.%, and atomic size misfit of ~4%.

36 MATERIALS SCIENCE↗

Pre- and post-annealing of mechanical damage in silicon wafers

Basic properties of mechanical damage in silicon consisting of cracks and abrasion were studied using transmission electron microscopy. The crystallographic structure of mechanical damage was determined before and after high temperature annealing. The main findings include that stresses in silicon around crack tips are not plastically relieved at room temperature and that abrasion at room temperature introduces shear loops into the silicon. It was also found that cracks of micron size can be annealed out, specifically, if cleavage occurs on 111 planes. The healing products of such cracks are 60 deg and 90 deg dislocations. Submicron cracks transform into stacking faults during annealing. Likewise high concentrations of shear loops due abrasion were found to anneal into stacking faults. A one to one correlation between surface areas containing small cracks and stacking faults was made. Measurements of damage removal on silicon surfaces through chemical-mechanical etching techniques are presented. It is shown that silicon dioxide repolishes damaged silicon surfaces most effectively.

Schwottke, G. H.↗

Lattice-mismatched In(0.40)Al(0.60)As window layers for indium phosphide solar cells

The efficiency of indium phosphide (InP) solar cells is limited by its high surface recombination velocity (approximately 10(exp 7) cm/s). This might be reduced by a wide-bandgap window layer. The performance of InP solar cells with wide-bandgap (1.8 eV) lattice-mismatched In(0.40)Al(0.60)As as a window layer was calculated. Because the required window layer thickness is less than the critical layer thickness, growth of strained (pseudomorphic) layers without interfacial misfit dislocations should be possible. Calculations using the PC-lD numerical code showed that the efficiencies of baseline and optimized p(+)n (p-on-n) cells are increased to more than 22 and 24 percent, (air mass zero (AMO), 25 C), respectively for a lattice-mismatched In(0.40)Al(0.60)As window layer of 10-nm thickness. Currently, most cell development work has been focused on n(+)p (n-on-p) structures although comparatively little improvement has been found for n(+)p cells.

Jain, Raj K.↗

Evolution of Pore Structure and Permeability of Rocks Under Hydrothermal Conditions (Final Report)

The physical and transport properties of porous rocks can be altered by a variety of diagenetic, metamorphic, and tectonic processes, and the changes that result are of critical importance to such industrial applications as resource recovery, carbon dioxide sequestration, and waste isolation in geologic formations. The associated interrelationships between rocks, pore fluids and deformation are also key to understanding many natural processes, including dynamic metamorphism, fault mechanics, fault stability and pressure solution creep. In this project, we investigated the changes of permeability and pore geometry owing to inelastic deformation by solution-transfer, brittle fracturing and dislocation creep. In particular, we studied the coupling between pore fluids and deformation in fluid-filled quartz, calcite, mudstones and ultramafic rocks and examine the effects of coupled mechanical and chemical processes on the evolution of porosity and permeability under hydrothermal conditions. The investigations used a combination of techniques, that included triaxial laboratory experiments; uniaxial compressive loading with in situ observations of microstructure; permeability under hydrostatic compression; observations of microstructure using optical and electron microscopes, and micro-CT imaging; and numerical calculations. Laboratory experiments were designed to provide mechanical and transport data under conditions that isolate the particular mechanisms responsible for the changes. The data obtained were used to quantify changes in surface roughness, porosity, pore dimensions and their spatial fluctuations. The results of the experiments and data from image analyses were compared to the results of network, finite-difference and other numerical models to verify the validity of experimentally established relations between permeability and other rock properties. A bibliography for the period from 2015-2019 is appended below. New results obtained in the final year and the unfunded extension period are detailed below.

58 GEOSCIENCES↗

Irradiation Creep in Materials

A knowledge of the dimensional stability of reactor structural components, under irradiation conditions, is of major importance in the design of thermal, fast, and fusion reactors. When subjected to simultaneous mechanical loading and irradiation, structural materials exhibit a visco-plastic deformation phenomenon, referred to as irradiation creep, which can be more rapid than the deformation occurring out of irradiation. In this article, the phenomenology of this peculiar behavior is described after a short history of its discovery. Then, the theoretical mechanisms proposed in the literature during these past 60 years are presented, with a special focus on mechanisms based on stress induced preferred absorption of point defects by dislocation loops, dislocations and grain boundaries and on mechanisms based on climb-enhanced glide of dislocations. These mechanisms are discussed in the light of experimental evidences. Finally, irradiation creep in various materials, such as zirconium alloys, austenitic stainless steels, nickel-based alloys, ferritic-martensitic steels and graphite, is described.

Onimus, Fabien↗

Mechanisms of radiation-induced segregation in CrFeCoNi-based single-phase concentrated solid solution alloys

Single-phase concentrated solid solution alloys have attracted wide interest due to their superior mechanical properties and enhanced radiation tolerance, which make them promising candidates for the structural applications in next-generation nuclear reactors. However, little has been understood about the intrinsic stability of their as-synthesized, high-entropy configurations against radiation damage. In this paper, we report the element segregation in CrFeCoNi, CrFeCoNiMn, and CrFeCoNiPd equiatomic alloys when subjected to 1250 kV electron irradiations at 400 °C up to a damage level of 1 displacement per atom. Cr/Fe/Mn/Pd can deplete and Co/Ni can accumulate at radiation-induced dislocation loops, while the actively segregating elements are alloy-specific. Moreover, electron-irradiated matrix of CrFeCoNiMn and CrFeCoNiPd shows L1 0 (NiMn)-type ordering decomposition and <001>-oriented spinodal decomposition between Co/Ni and Pd, respectively. Finally, these findings are rationalized based on the atomic size difference and enthalpy of mixing between the alloying elements, and identify a new important requirement to the design of radiation-tolerant alloys through modification of the composition.

36 MATERIALS SCIENCE↗

Atomic configurations at InAs partial dislocation cores associated with Z-shape faulted dipoles

The atomic arrangements of two types of InAs dislocation cores associated by a Z-shape faulted dipole are observed directly by aberration-corrected high-angle annular-dark-field imaging. Single unpaired columns of different atoms in a matrix of dumbbells are clearly resolved, with observable variations of bonding lengths due to excess Coulomb force from bare ions at the dislocation core. The corresponding geometric phase analysis provides confirmation that the dislocation cores serve as origins of strain field inversion while stacking faults maintain the existing strain status.

TRANSMISSION ELECTRON MICROSCOPY↗

Molecular beam epitaxy growth of wurtzite AlN nanotips

The characteristics of structure and morphology of AlN nanotips grown under higher V/III ratio on Si (111) with plasma-assisted molecular beam epitaxy are herein investigated. We found that the AlN nanotips were single crystalline with (1-211) inclined facets and embedded in pitlike defects of N-polarity. The density and size of the AlN nanotips can be controlled by the growth conditions. The AlN nanotip growth mechanism can be rationalized as the c-type dislocations generated between two adjacent grains due to the formation of higher strain area in the early stages of growth. The c-type dislocation would reverse the stacking sequence of the following adatoms, leading to the AlN nanotip growth with inverse polarity and higher growth rate compared to the surrounding matrix. These nanotips might serve as the ideal templates for further growth of nanostructure devices.

36 MATERIALS SCIENCE↗

Nanoindentation of high-purity vapor deposited lithium films: A mechanistic rationalization of the transition from diffusion to dislocation-mediated flow

Nanoindentation experiments performed in high-purity vapor deposited lithium films at 31 °C reveal a strain rate and length scale dependence in the stress at which pop-in type events signal an abrupt transition from diffusion to dislocation-mediated flow. The stress level at which the transition to dislocation-mediated flow occurs varies with the strain rate and ranges from 88 to 208 times larger than the nominal yield strength of bulk, polycrystalline lithium. Variation in the indentation strain rate reveals the relationship between the stress required to initiate the transition and the length scale at which the transition occurs follows the power-law relation, hardness × depth 1.17 = 1.545 N/m 0.83 , where the magnitude of the exponent and constant reflect the defect structure of the film. In conclusion, a rationalization of the transition is provided through direct comparisons between the measured cumulative distribution function (CDF) and the CDF hypothesized for the activation of a Frank–Read source.

36 MATERIALS SCIENCE↗

Shape memory and superelasticity of nanograined Ti-51.2 at.% Ni alloy processed by severe plastic deformation via high-ratio differential speed rolling

A novel method of producing nanograined Ni-rich superelastic NiTi alloys in sheet form was proposed using a combination of severe plastic deformation via high-ratio differential speed rolling (HRDSR) and post-deformation annealing. The HRDSR-processed microstructure was composed of heavily deformed austenite and martensite grains, and amorphous phases. After annealing at 673 K, the severely deformed microstructure with no functional properties evolved to the nanograined structure (20–70 nm) composed of austenite and martensite nanograins and sub-nanograins through static recovery or continuous static recrystallization process. The nanograined microstructure had a high resistance to martensitic transformation upon cooling and slip deformation during straining. As a result, the HRDSR-processed alloy annealed at 673K exhibited superior superelasticity compared to the alloys with coarse grains. At the higher annealing temperature of 873 K, the micron-sized recrystallized grains with low dislocations developed through discontinuous static recrystallization process. In this case, deformation during straining was governed by the detwinning of twinned martensite, and as a result, shape memory effect was more significantly pronounced than superelasticity.

36 MATERIALS SCIENCE↗

Two-step deformation-induced martensitic transformation in additively manufactured High-Si stainless steel

Deformation-induced phase transformation in the additively manufactured (AM) Fe–18Cr–8Ni-5.5Si (in wt.%) alloy was analyzed using the in-situ electron backscattered diffraction (EBSD) record during uniaxial tensile testing in a scanning electron microscope (SEM). Analysis of EBSD data was focused to investigate phase transformation behavior during deformation with consideration of mechanical interactions among phases and grains in the ultrafine AM microstructure. The initial EBSD phase map illustrated that the as-built microstructure was a duplex structure consisting of major austenite (γ) and minor ferrite phases, some of which showed non-traditional orientation relationship since the rapid solidification in the AM process has produced non-equilibrium state in phase formation. In the deformed as-built AM alloy, the two-step martensitic transformation (γ→ε→α´) was identified as the main deformation-induced transformation mechanism. Martensitic transformation steps were found to be associated with glides of Shockley partial dislocations on closed packed (111) planes under the influence of atomic disturbance in the γ and ε phases, respectively. Using the closed-packed plane pole figures and unit cell orientations, their evolutions and mechanisms accompanying with the transformation were analyzed. Finally, the results indicate that one variant of ε-martensite forms from their parent γ phase, while two variants of α´ form from their parent ε phase.

36 MATERIALS SCIENCE↗

Dynamics and structure of the B2→B19’ phase transformation in NiTi revealed through in situ 4D-STEM

The structural evolution of NiTi during the B2→B19’ martensitic phase transformation via thermal cycling is investigated using in situ four dimensional scanning transmission electron microscopy (4D-STEM). With 4D-STEM, we can directly visualize and quantify the nanoscale evolution of the martensitic structure on thermal cycling and also investigate the origin of diffuse scattering of NiTi in the pre-transitional state. Mapping of the martensite orientation and strain visualizes the progression of the transformation front and self-accommodation of the B19’ structure. Diffuse streaking and strain are measured in the pre-transitional austenite (B2) phase and demonstrate no localization or preferential directionality hinting that long-range homogeneous instability rather than nanoscale heterogeneities may be the origin of the pre-transitional anomalies in NiTi. Finally, it is revealed that NiTi does not reform the same martensite nanostructure on thermal cycling but does express similar features. This small variation is likely owing to transformation-induced dislocations.

36 MATERIALS SCIENCE↗

Correlation of creep rate with microstructural changes during high temperature creep

The techniques of electron microscopy were used to examine the microstructural changes which occur during primary creep for two important types of engineering alloys: (1) alloys strengthened by solid-solution additions, and (2) dispersion-strengthened alloys. The metals chosen for study are unalloyed titanium, Ti-6Al-4V, and the cobalt-base alloy, Haynes 188. Results to date on NGR 47-004-108 show that development of prior dislocation substructure in Haynes 188 by 10% prestrain and annealing for one hour at 1800 F increases the time to reach 0.5% creep strain at 1600 F by more than an order of magnitude for creep stresses from 3 to 20 ksi. For creep at 1800 F, similar results were obtaind for stresses above 7 ksi, but the prior substructure decreases creep resistance below 7 ksi. This effect appears to be related to instability of grain structure at 1800 F in prestrained material.

Young, C. T.↗