Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel performance analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Secondary Protection for 70 MPa Fueling - A White Paper from the Hydrogen Safety Panel

In developing a 70 megapascal (MPa) fueling infrastructure, it is critical to ensure that a vehicle equipped with a lower service pressure fuel tank is never filled from a 70 MPa fueling source. Filling of a lower service pressure vehicle at a 70 MPa fueling source is likely to result in a catastrophic event with severe injuries or fatalities. The Hydrogen Safety Panel recommends that DOE undertake a two-step process to address this issue: 1. Perform an independent risk analysis of a 70MPa dispenser filling a lower pressure vehicle tank and develop different approaches for prevention and mitigation to meet an acceptable level of safety. Cost effectiveness, reliability, advantages and disadvantages are among the factors that should be evaluated for each approach considered. 2. Until such time as this analysis is complete and any recommended actions implemented, communicate the potential risk to responsible parties and strongly encourage those parties to add a secondary layer of protection to the existing system of mechanically non-interchangeable nozzles/receptacles. This will reduce the probability of a pressure mismatch during this developmental phase for hydrogen fuel cell vehicles and infrastructure. This step can be reassessed after further analysis is completed and the need and effectiveness of secondary protection methods are evaluated. This paper provides background discussion of the problem, current safety systems and strategy and examples of potential future solutions to support the above recommendations.

08 HYDROGEN↗

Hydrothermal Liquefaction of Biomass

Hydrothermal liquefaction technology is describes in its relationship to fast pyrolysis of biomass. The scope of work at PNNL is discussed and some intial results are presented. HydroThermal Liquefaction (HTL), called high-pressure liquefaction in earlier years, is an alternative process for conversion of biomass into liquid products. Some experts consider it to be pyrolysis in solvent phase. It is typically performed at about 350 C and 200 atm pressure such that the water carrier for biomass slurry is maintained in a liquid phase, i.e. below super-critical conditions. In some applications catalysts and/or reducing gases have been added to the system with the expectation of producing higher yields of higher quality products. Slurry agents ('carriers') evaluated have included water, various hydrocarbon oils and recycled bio-oil. High-pressure pumping of biomass slurry has been a major limitation in the process development. Process research in this field faded away in the 1990s except for the HydroThermal Upgrading (HTU) effort in the Netherlands, but has new resurgence with other renewable fuels in light of the increased oil prices and climate change concerns. Research restarted at Pacific Northwest National Laboratory (PNNL) in 2007 with a project, 'HydroThermal Liquefaction of Agricultural and Biorefinery Residues' with partners Archer-Daniels-Midland Company and ConocoPhillips. Through bench-scale experimentation in a continuous-flow system this project investigated the bio-oil yield and quality that could be achieved from a range of biomass feedstocks and derivatives. The project was completed earlier this year with the issuance of the final report. HydroThermal Liquefaction research continues within the National Advanced Biofuels Consortium with the effort focused at PNNL. The bench-scale reactor is being used for conversion of lignocellulosic biomass including pine forest residue and corn stover. A complementary project is an international collaboration with Canada to investigate kelp (seaweed) as a biomass feedstock. The collaborative project includes process testing of the kelp in HydroThermal Liquefaction in the bench-scale unit at PNNL. HydroThermal Liquefaction at PNNL is performed in the hydrothermal processing bench-scale reactor system. Slurries of biomass are prepared in the laboratory from whole ground biomass materials. Both wet processing and dry processing mills can be used, but the wet milling to final slurry is accomplished in a stirred ball mill filled with angle-cut stainless steel shot. The PNNL HTL system, as shown in the figure, is a continuous-flow system including a 1-litre stirred tank preheater/reactor, which can be connected to a 1-litre tubular reactor. The product is filtered at high-pressure to remove mineral precipitate before it is collected in the two high-pressure collectors, which allow the liquid products to be collected batchwise and recovered alternately from the process flow. The filter can be intermittently back-flushed as needed during the run to maintain operation. By-product gas is vented out the wet test meter for volume measurement and samples are collected for gas chromatography compositional analysis. The bio-oil product is analyzed for elemental content in order to calculate mass and elemental balances around the experiments. Detailed chemical analysis is performed by gas chromatography-mass spectrometry and 13-C nuclear magnetic resonance is used to evaluate functional group types in the bio-oil. Sufficient product is produced to allow subsequent catalytic hydroprocessing to produce liquid hydrocarbon fuels. The product bio-oil from hydrothermal liquefaction is typically a more viscous product compared to fast pyrolysis bio-oil. There are several reasons for this difference. The HTL bio-oil contains a lower level of oxygen because of more extensive secondary reaction of the pyrolysis products. There are less amounts of the many light oxygenates derived from the carbohydrate structures as they have been further reacted to phenolic Aldol condensation products. The bio-oil is more hydrophobic because of the lower oxygen content and resulting lower polarity and therefore has a lower amount of dissolved water. Without the light oxygenates acting as solvents along with the water, the bio-oil product is much more viscous. Related results are that the bio-oil is less dense and has a higher energy content. These differences in properties led to the earlier held belief that the HTL bio-oils could be upgraded by catalytic hydroprocessing in a manner more similar to simple petroleum hydrotreating. Some initial results from the HydroThermal Liquefaction of kelp are shown in Table 1. The experiments were performed with kelp slurries of 5-13 wt.% dry solids in water. Oil yields from kelp are low at 24% on ash-free basis but up to 41% calculated on a carbon basis. The bulk of the rest of the carbon ends up dissolved in the water stream.

02 PETROLEUM↗

Systems Performance Analyses of Alaska Wind-Diesel Projects; St. Paul, Alaska (Fact Sheet)

This fact sheet summarizes a systems performance analysis of the wind-diesel project in St. Paul, Alaska. Data provided for this project include load data, average wind turbine output, average diesel plant output, dump (controlling) load, average net capacity factor, average net wind penetration, estimated fuel savings, and wind system availability.

17 WIND ENERGY↗

When Is the Simple Radiotoxicity Approach Useful for Advanced Fuel Cycle System Assessments Given the Existence of Complex Performance Dose Assessments?

Engineers often face the general question of which approximations are appropriate for a given analytical task. In particular, when is a simpler model useful if a more complex model also exists? This paper explores this question in the domain of radiotoxicity relative to geologic disposal performance dose assessments. Criterion 1 requires that the simpler approach, radiotoxicity, must be calculated correctly. The concept of ingestion radiotoxic inventories is analogous to the inventory of toxic chemicals in other industries. From a decision analysis perspective, it is also somewhat analogous to the nuclear reactor safety concept of “passive safety.” This paper explains some of the issues in calculating radiotoxicity, motivated by the author’s observations of errors in the literature: not accounting for radioactive progeny, misunderstanding natural “ore,” and focusing on transuranic (TRU) isotopes without adequate attention to actinide decay products. For example, Th/233U fuel cycles do have lower amounts of TRU isotopes than U/239Pu fuel cycles, but that does not necessarily mean lower long-term hazard. Criterion 2 requires that the uncertainties in the more complex approach, performance dose assessments, must raise issues for the assessments’ intended purposes—in which case, radiotoxic inventory may be of assistance until those issues are resolved. Performance dose assessments were developed for, and are legally the way to show, compliance with regulations, but the uncertainties are large. Less obvious is the degree to which dose assessments are applicable to other purposes—comparing fuel cycle options prior to site selection and showing the safety of a fuel cycle and waste management approach to the public. In the last sense especially, performance dose assessments are analogous to probabilistic risk assessments for nuclear reactor safety. The United States lacks a selected consensus site, selected fuel cycle approach (direct disposal versus recycling), and selected waste form. Thus, the paper does not intend to discuss all the issues with performance dose assessments but rather intends to focus on only those performance dose uncertainties that raise issues when comparing fuel cycles. Uncertainties associated with whether a generic geological environment is attractive or a specific location meets requirements are beyond the scope of this paper. Ingestion radiotoxicity correlates with heat, gamma, and inhalation radiotoxicity. Thus, options that are relatively high in ingestion radiotoxicity tend to be high in other parameters. Therefore, reduction in ingestion radiotoxicity means both that the potential source term for release is lower but also that one driving force for release (heat) is also lower. However, the most important time frames differ as heat is mainly an issue in decades and centuries after reactor discharge, but ingestion radiotoxicity is mainly an issue during longer time periods. Ingestion radiotoxicity points to the importance of actinides in long-term waste management, followed by specific fission products such as 99Tc, 129I, 93Zr, 135Cs, and 79Se.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BISON-FIPD integration enhanced low-burnup SFR metallic fuel swelling model evaluation framework

Experiments indicated that metallic fuel in sodium-cooled fast reactors (SFRs) rapidly swells radially and axially at low burnup. Despite that, prior studies have been focused on describing high burnup axial fuel elongation. With recent conventional and non-conventional metallic fuel concepts being considered for license applications, understanding multidimensional fuel swelling at a wide range of burnup levels is important to fuel analysis and qualification activities. Here, we report the development and demonstration efforts of a low-burnup SFR metallic fuel swelling model evaluation framework using the BISON advanced fuel performance code. The framework leverages the Integral Fast Reactor (IFR) program X423 experiment data through the ongoing integration project to enable standardized and automated use of legacy metallic fuel irradiation data maintained in the SFR fuel irradiation and physics database (FIPD) for BISON metallic fuel model verification and validation. In conclusion, the performance of the framework was demonstrated using the two representative metallic fuel swelling model sets implemented in BISON, with a series of insights about future advanced swelling model development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

GTL-1 Irradiation Summary Report

The primary objective of the Gas Test Loop (GTL-1) miniplate experiment is to confirm acceptable performance of high-density (i.e., 4.8 g-U/cm3) U3Si2/Al dispersion fuel plates clad in Al-6061 and irradiated under the relatively aggressive Booster Fast Flux Loop (BFFL) booster fuel conditions, namely a peak plate surface heat flux of 450 W/cm2. As secondary objectives, several design and fabrication variations were included in the test matrix that may have the potential to improve the high-heat flux, high-temperature performance of the base fuel plate design.1, 2 The following report summarizes the life of the GTL-1 experiment through end of irradiation, including as-run neutronic analysis, thermal analysis and hydraulic testing results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Coupling between TOUGH3 and FLAC3D

Sandia National Laboratories has hired Itasca Consulting Group, Inc., the authors of the FLAC3D geomechanics software, to couple FLAC3D with TOUGH3, the porous media flow solver. The work is being done to enable a coupled mechanical-thermal-hydraulic analysis of a potential criticality event in a dual purpose cannister (DPC). The U.S. Department of Energy Office of Spent Fuel and Waste Science & Technology is investigating the performance of DPCs for direct geological disposal of spent nuclear fuel. Post closure criticality control is an important aspect of this investigation. Over geological timescales, it is envisioned that the canister and canister overpack will develop fractures due to stress corrosion processes. A breach in the canister could allow groundwater to fill the canister. Fresh water is a neutron moderator; thus, if the canister internals and fuel assemblies have been sufficiently degraded, a criticality event could occur. Such an event would release enough energy to boil the water between the fuel rods and pressurize the cannister. This internal pressurization may cause the initial fractures in the canister and overpack to grow. It is important to understand the change in hydraulic transmissivity between the canister and surroundings for two reasons: first, because it may control the potential for and frequency of subsequent criticality events; second, because it will control the release of radionuclides from the canister. The motivation for this work is to better understand the potential for periodic criticality events, cannister damage, and release of radionuclides during a criticality event in a DPC.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Development of a Fuel Cell for the Perhydrodibenzyltoluene / Dibenzyltolluene Fuel Pair

An experimental study of the performance of an LFC with H-DBT and other cyclic hydrogenated aromatic fuels was carried out, along with a characterization of the fuel cell conversion products. A technoeconomic analysis (TEA) of the LFC operating in a class 8 truck powertrain using the H-DBT / DBT fuel pair was completed to determine the total cost of ownership (TCO), comparing LFC vehicles (LFCVs) to HFC vehicles (HFCVs), battery electric vehicles (BEVs), and diesel trucks on a pro-forma basis assuming the LFC could be developed to HFC benchmarks.

08 HYDROGEN↗

Qualification of Digitized Legacy Fast Reactor Data

The Integral Fast Reactor (IFR) fuel compatibility test program (1984-1994) included a variety of fuel pin examinations conducted at the Hot Fuel Examination Facility (HFEF) and the Alpha-Gamma Hot Cell Facility (AGHCF). Hard copy data records of these examinations have been recovered, scanned, and preserved in PDF format. Many hard copy records are now qualified in accordance with an NRC-approved Quality Assurance Program Plan (QAPP), and there is an ongoing effort to qualify additional legacy records. This legacy fuel performance data is vital to support design and licensing of fast reactors with validation of state-of-the-art codes and advanced methods for design and analysis. Stakeholders can most easily utilize this data when the PDF scans have been converted into digital data tables. However, qualification of the scanned hard copy data does not qualify the digital data file resulting from the digitization of the data contained in the record; the subject matter expert (SME) must make a review of the digitized data table as well before it can be designated as qualified. This report outlines a peer review process to qualify the digital data file(s), typically in CSV format, corresponding to hard copy records in accordance with the existing QAPP.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Program For Optimization Of Nuclear Rocket Engines

NOP is versatile digital-computer program devoloped for parametric analysis of beryllium-reflected, graphite-moderated nuclear rocket engines. Facilitates analysis of performance of engine with respect to such considerations as specific impulse, engine power, type of engine cycle, and engine-design constraints arising from complications of fuel loading and internal gradients of temperature. Predicts minimum weight for specified performance.

Plebuch, R. K.↗

Engine Operation in Flight for Minimum Fuel Consumption

Engine and airplane performance data have been gathered from various sources and analyzed to determine indications of the most economical methods of flight operation from a consideration of fuel expenditure. The analysis includes the influence of such facts as fuel-air ratio, engine speed, engine knock, altitude, cylinder cooling, spark timing, and limits of cruising brake mean effective pressure. The results indicate that the cheapest power is obtained with approximately correct mixture at low engine speed and highest permissible manifold pressure. If more power is desired, the methods of obtaining it are, in order of fuel economy: (a) increasing the engine speed and maintaining safe cylinder temperatures by cooling; (b) retarding the spark or cooling further to permit higher manifold pressure; and, (c) riching the mixture. The analysis further shows that the maximum time endurance of flight occurs at the air speed corresponding to minimum thrust horsepower required and with minimum practicable engine speed. Maximum mileage per pound of fuel is obtained at slightly higher air speed. The fuel-air ratio should be approximately the theoretically correct ratio in both cases. For an engine equipped with a geared supercharger, as in the example presented, and with knock as the limiting condition, a comparison of operation at sea level and at 6,000 feet shoes flight at altitude to be more economical on the basis of both range and endurance.

Reuter, George↗

DEMONSTRATION OF MULTI-PHYSICS EVALUATION OF FUEL ROD BURST PROBABILITY WITH BURNUP EXTENSION UNDER LBLOCA CONDITIONS

Extending the fuel discharge burnup level, e.g., from the current limit of rod averaged discharge burnup limit of 62 GWD/MT to a proposed new limit of 75 GWD/MT, can provide significant economic benefits to the current fleet of operating light water reactors (LWRs). It allows for longer operating cycles and improved resource utilization. The major economic gain of longer operating cycles is attributable to the increased capacity factor resulting from decreased refueling time as a fraction of total operating time, as well as fewer assemblies to be discharged for a given amount of energy produced. The main licensing challenges for higher burnup fuel are to ensure fuel rod safety under design basis accident conditions, especially under large-break loss-of-coolant accident (LBLOCA) and reactivity insertion accident (RIA). In this work, two-year cycle core design for a typical 4-loop pressurized water reactor (PWR) is performed with enrichment increased up to 6% and burnup extended to 75 GWD/MT. The fuel rod burst potential evaluations under large-break loss-of-coolant accident (LBLOCA) conditions are subsequently performed using the multi-physics best estimate plus uncertainty analysis framework LOTUS (LOCA Toolkit for the U.S. LWRs) and the preliminary results are presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

MICROREACTOR APPLICATIONS, RESEARCH, VALIDATION, AND EVALUATION (MARVEL) REACTOR ? STATUS, CONSTRUCTION, AND TESTING

The paper presents the current status of the Microreactor Applications, Research, Validation, and Evaluation (MARVEL) microreactor design, qualification testing, fabrication, and high-level construction schedule. An overview of initial criticality, low power physics testing, and start-up testing is included, as well as an overview of the envisioned processes in which end-users can engage the project for access to operational data or specific demonstrations. Designed by the Idaho National Laboratory (INL) under the auspices of the US Department of Energy’s Microreactor Program for construction and operation at the INL, MARVEL is a small, fully functional advanced reactor with UZrH fuel and thermal output of 85 kW. It offers a unique opportunity for scaled demonstrations that can dramatically accelerate the design, licensing, and deployment of commercial microreactors for power production or process heat applications. MARVEL’s objective is to build a small liquid-metal thermal reactor at the INL to demonstrate design and operating processes for microreactors, microgrid integration, and process heat applications. MARVEL finished 90%-final-design in September 2023 and completed an independent project assessment in early 2024. Fabrication of long-lead components and fuel, safety analysis review, and procurement for construction are underway. MARVEL assembly and construction will start in 2025 and fuel loading is expected in mid- 2027. Initial criticality will be performed in a dry condition in late 2027, followed by loading of NaK coolant and start-up testing. Approximately six months later, release for unrestricted operations will enable subsequent testing of microreactor characteristics, microgrid integration and select heat extraction applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Prediction of crack propagation paths in the unit cell of SOFC stacks

Planar Solid Oxide Fuel Cells (SOFC) stacks are multi-material layered systems with different thermo-mechanical properties. Due to their severe thermal loading, these layers have to meet high demands to preserve their mechanical integrity without initiation and propagation of fracture. Here, we focus on a typical unit cell of the stack which consists of positive electrode-electrolyte-negative electrode (PEN). Based on the mechanical properties of each layer and their interfaces, an energy criterion as a function of crack length is used for the prediction of possible crack extensions in the PEN. This criterion is a pure local criterion, independent of applied loads and geometry of the specimen. An analysis of the competition between crack deflections in the interfaces and crack penetration in layers is presented.

30 DIRECT ENERGY CONVERSION↗

Uncertainty analysis on reactivity and discharged inventory for a pressurized water reactor fuel assembly due to {sup 235,238}U nuclear data uncertainties

This paper discusses the uncertainty analysis on reactivity and inventory for a typical PWR fuel element as a result of uncertainties in {sup 235,238}U nuclear data. A typical Westinghouse 3-loop fuel assembly fuelled with UO{sub 2} fuel with 4.8% enrichment has been selected. The Total Monte-Carlo method has been applied using the deterministic transport code DRAGON. This code allows the generation of the few-groups nuclear data libraries by directly using data contained in the nuclear data evaluation files. The nuclear data used in this study is from the JEFF3.1 evaluation, and the nuclear data files for {sup 238}U and {sup 235}U (randomized for the generation of the various DRAGON libraries) are taken from the nuclear data library TENDL. The total uncertainty (obtained by randomizing all {sup 238}U and {sup 235}U nuclear data in the ENDF files) on the reactor parameters has been split into different components (different nuclear reaction channels). Results show that the TMC method in combination with a deterministic transport code constitutes a powerful tool for performing uncertainty and sensitivity analysis of reactor physics parameters. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Thermal Predictions of the AGR-3/4 Experiment With Time-Varying Gas Gaps

In this paper, a thermal analysis was performed for the Advanced Gas Reactor test experiment (AGR-3/4) with time-varying gas gaps. The experiment was irradiated at the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). Several fuel irradiation experiments are planned for the AGR Fuel Development and Qualification Program that supports the development of the Very-High-Temperature Gas-Cooled Reactor (VHTR) under the Next-Generation Nuclear Plant (NGNP) project. AGR-3/4 combines two tests in a series of planned AGR experiments to test tristructural-isotropic (TRISO)-coated, low-enriched uranium oxy-carbide fuel. Forty-eight TRISO-fueled compacts were inserted into 12 separate capsules for the experiment (four compacts per capsule). The purpose of this analysis was to calculate the temperatures of each compact and graphite layer to obtain daily average temperatures using time (fast neutron fluence)-varying gas gaps and to compare with experimentally measured thermocouple data. A finite-element heat transfer model was created for each capsule using the commercial code ABAQUS. Finally, model results are compared to thermocouple data taken during the experiment.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Performance of Anode-Supported Solid Oxide Fuel Cell with Thin Bi-Layer Electrolyte by Pulsed Laser Deposition

Anode-supported yttria stabilized zirconia (YSZ)/samaria doped ceria (SDC) bi-layer electrolytes with uniform thickness and high density were fabricated by pulsed laser deposition at 1000 degrees C. Fuel cells with such bi-layer electrolytes were fabricated and tested, yielding open circuit voltages from 0.94 to 1.0 V at 600-700 degrees C. Power densities from 0.4 to 1.0 W cm{sup -2} at 0.7 V were achieved in air at temperatures of 600-700 degrees C. Cell performance was improved in flowing oxygen, with an estimated peak power density of over 2 W cm{sup -2} at 650 degrees C, assuming the same overall resistance over the entire range of current density. The high cell performance was attributed to the very low ohmic resistance of the fuel cell, owing to the small thickness of the electrolyte. Stable performance was also demonstrated in that the voltage of the fuel cell showed very little change at a constant current density of 1 A cm{sup -2} during more than 400 hours of operation at 650 degrees C in flowing oxygen. SEM analysis of the fuel cell after testing showed that the bi-layer electrolyte had retained its chemical and mechanical integrity.

30 DIRECT ENERGY CONVERSION↗

Preliminary analysis of core heat-up for ATFs under accident conditions

The accident-tolerant fuel (ATF) system is aim at upgrading safety characteristics of the nuclear fuel and cladding in a reactor core where active cooling has been lost, and is preferable or comparable to the conventional UO{sub 2}-Zr fuel system when the reactor is in normal operation. In this paper, the improved performance of UO{sub 2}-SiC, UO{sub 2}-FeCrAl fuel systems, and of fully ceramic micro-encapsulated (FCM) fuels: FCM-SiC and FCM-FeCrAl, on the core heat-up progress in a pressurized water reactor (PWR) is analyzed by using the best-estimate system code RELAP5 and severe accident analysis program. For this purpose two accident scenarios are selected: a large break LOCA as a design base accident and an extended station blackout (SBO) severe accident. For the LBLOCA with just low-pressure safety injection, larger volumetric heat capacity and thermal conductivity of ATF materials contribute to a larger safety margin in terms of the peak cladding temperature compared with UO{sub 2}-Zr. Thanks to higher melting temperatures, FCM-SiC is failed by melting almost 1200 s later than UO{sub 2}-Zr. The accumulated production of hydrogen for ATF materials is around 10 times smaller than that for UO{sub 2}-Zr. However, high temperature oxidation of SiC cladding generates carbon monoxide which is combustible, while the melting point of FeCrAl is not high enough. In the SBO scenario with mitigation measure, the advantage of ATF is more evident. If the mitigation measure could not be taken, core heatup is inevitable for all types of fuel system, but the temperature rising of ATF core is much slower. In general, improved high-temperature properties and resistance to oxidation play important roles for ATF cores.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗