Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Theory and Experiment of Multielement Airfoils: A Comparison

A detailed comparison of computed and measured pressure distributions, velocity profiles, transition onset, and Reynolds shear stresses for multi-element airfoils is presented. It is shown that the transitional k-zeta model, which is implemented into CFL3D, does a good job of predicting pressure distributions, transition onset, and velocity profiles with the exception of velocities in the slat wake region. Considering the fact that the hot wire used was not fine enough to resolve Reynolds stresses in the boundary layer, comparisons of turbulence stresses varied from good to fair. It is suggested that the effects of unsteadiness be thoroughly evaluated before more complicated transition/turbulence models are used. Further, it is concluded that the present work presents a viable and economical method for calculating laminar/transitional/turbuient flows over complex shapes without user interface.

Czerwiec, Ryan↗

Investigation of Turbine-outlet Temperature Distribution of XJ34-WE-32 Turbojet Engine

Turbine-outlet radial temperature distributions of an XJ34-WE-32 turbojet engine were investigated in the altitude wind tunnel at the NACA Lewis laboratory over a range of pressure altitudes, engine-inlet air temperatures and flight Mach numbers at or near rated engine conditions. From blade stress considerations, the turbine-outlet temperature distribution was considered satisfactory at altitudes up to 25,000 feet at corrected engine speeds corresponding to rated speed (12,500 rpm); however, operation at either higher corrected engine speeds or higher altitudes resulted in an inversion of the turbine temperature distribution that was detrimental to turbine life. Installation of a compressor-outlet mixer greatly improved the turbine radial temperature distribution.

Prince, W R↗

Particle Distribution in Suspension Shear Flow

An earlier proposed constitutive relation for normal stresses originated by random particle fluctuations is used to describe a joint effect of thermal and shear-induced fluctuations on concentrational distributions in suspension flow. Averaged products of components of the fluctuation velocity are evaluated on a basis of the rational mechanics approach combined with a simple kinematic consideration. The equation of momentum conservation of the dispersed phase of a suspension closed with this constitutive relation is applied to unidirectional shear flow in the gravity field and to rotational Couette flow. Coupling of the thermal and shear-induced fluctuations results in that the ability of shear flow to suspend particles has a minimum at a certain particle size, all other things being equal. The developed model provides also for a reasonable explanation of particle distributions observed in Couette flow. The approach based on the consideration of momentum balance for the dispersed phase is proved to lead to an effective equation of convective diffusion of the suspended particles. Coefficients of mutual diffusion due to both thermal and shear-induced fluctuations are drastically different from corresponding self-diffusivities as regards both their scaling and their concentrational dependence.

Buyevich, Yu A.↗

Derivation of heterogeneous material distributions and their sensitivity to HM-coupled two-phase flow models exemplified with the LASGIT experiment

Abstract Advective gas transport in bentonite, a possible buffer material in repositories for radioactive materials, is difficult to simulate in numerical continuum models, partly due to the complicated microstructure of bentonite. To generate reliable models of repositories nevertheless, spatially distributed heterogeneous material properties can be used to allow localization of gas flow. In this study, a pore-size-dependent stochastic approach of the gas entry pressure is derived from Mercury Intrusion Porosimetry, which is used to replicate measurements from the LASGIT experiment. In addition, three benchmark tests are simulated to investigate the dependence of heterogeneous distributions of material properties on the mesh discretization, the temporal dependence, and the coupling between the processes influenced by the heterogeneous parameters. The numerical modeling results of the LASGIT experiment show that the onset of gas flow into the system and the subsequent increase in pressure and stress can be well reproduced using heterogeneous distributions. Compared to a model with homogeneous material properties, heterogeneous distributions may allow the generation of dilatancy-controlled microfractures—an important feature with regard to the advective gas flow in bentonites. However, it can be observed that the heterogeneous distributions in LASGIT are less significant, as technical gaps or differences in material types could have a greater impact.

Environmental Sciences & Ecology↗

Tailoring Piezoelectricity of 3D Printing PVDF-MoS 2 Nanocomposite via In Situ Induced Shear Stress

3D printing of unique structures with tunable properties offers significant advantages in the fabrication of complex and customized electronic devices. Here, this study introduces a process-microstructure–property-guided manufacturing route to fabricate PVDF-2D MoS 2 piezoelectric nanocomposites with tunable piezoelectric properties without having a postprocess. We control PVDF’s microstructure through direct ink writing (DIW) 3D printing while tuning PVDF-MoS 2 interfacial strain by controlling rheology and 3D printing parameters, such as nozzle size and printing speed. Our approach demonstrates tunable piezoelectricity in PVDF-MoS 2 , achieving a 15-fold increase in the piezoelectric coefficient (d 33 ) at a printing-induced shear stress of 6685 Pa. This enhancement arises from the electrostatic interactions between PVDF and MoS 2 and the filler distribution and alignment caused by the in situ shear stress in 3D printing, as confirmed by XPS and Raman mapping analyses. Our findings advance the understanding of piezoelectric mechanisms in PVDF-based nanocomposites, laying the foundation for 3D printing of piezoelectric sensors in wearable device applications with enhanced performance and customization capabilities.

2D MoS2↗

Long-term 3D MHD simulations of black hole accretion discs formed in neutron star mergers

ABSTRACT We examine the long-term evolution of accretion tori around black hole (BH) remnants of compact object mergers involving at least one neutron star, to better understand their contribution to kilonovae and the synthesis of r-process elements. To this end, we modify the unsplit magnetohydrodynamic (MHD) solver in flash 4.5 to work in non-uniform three-dimensional spherical coordinates, enabling more efficient coverage of a large dynamic range in length scales while exploiting symmetries in the system. This modified code is used to perform BH accretion disc simulations that vary the initial magnetic field geometry and disc compactness, utilizing a physical equation of state, a neutrino leakage scheme for emission and absorption, and modelling the BH’s gravity with a pseudo-Newtonian potential. Simulations run for long enough to achieve a radiatively inefficient state in the disc. We find robust mass ejection with both poloidal and toroidal initial field geometries, and suppressed outflow at high disc compactness. With the included physics, we obtain bimodal velocity distributions that trace back to mass ejection by magnetic stresses at early times, and to thermal processes in the radiatively inefficient state at late times. The electron fraction distribution of the disc outflow is broad in all models, and the ejecta geometry follows a characteristic hourglass shape. We test the effect of removing neutrino absorption or nuclear recombination with axisymmetric models, finding ${\sim} 50{{\ \rm per\ cent}}$ less mass ejection and more neutron-rich composition without neutrino absorption, and a subdominant contribution from nuclear recombination. Tests of the MHD and neutrino leakage implementations are included.

Fahlman, Steven (ORCID:0000000348759940)↗

A Comparison of Radiation-Induced and High-Field Electrically Stress-Induced Interface Defects in Si/SiO 2 MOSFETs via Electrically Detected Magnetic Resonance

Here, we utilize electrically detected magnetic resonance (EDMR) measurements to compare high-field stressed, and gamma irradiated Si/SiO 2 metal–oxide–silicon (MOS) structures. We utilize spin-dependent recombination (SDR) EDMR detected using the Fitzgerald and Grove dc I-V approach to compare the effects of high-field electrical stressing and gamma irradiation on defect formation at and near the Si/SiO 2 interface. As anticipated, both greatly increase the concentration of P b centers (silicon dangling bonds at the interface) densities. The irradiation also generated a significant increase in the dc I-V EDMR response of E' centers (oxygen vacancies in the SiO 2 films), whereas the generation of an E' EDMR response in high-field stressing is much weaker than in the gamma irradiation case. These results likely suggest a difference in their physical distribution resulting from radiation damage and high electric field stressing.

42 ENGINEERING↗

Analysis of in-flight boundary-layer state measurements on a subsonic transport wing in high-lift configuration

Flight experiments on NASA Langley's B737-100 (TSRV) airplane have been conducted to document flow characteristics in order to further the understanding of high-lift flow physics, and to correlate and validate computational predictions and wind-tunnel measurements. The project is a cooperative effort involving NASA, industry, and universities. In addition to focusing on in-flight measurements, the project includes extensive application of various computational techniques, and correlation of flight data with computational results and wind-tunnel measurements. Results obtained in the most recent phase of flight experiments are analyzed and presented in this paper. In-flight measurements include surface pressure distributions, measured using flush pressure taps and pressure belts on the slats, main element, and flap elements; surface shear stresses, measured using Preston tubes; off-surface velocity distributions, measured using shear-layer rakes; aeroelastic deformations of the flap elements, measured using an optical positioning system; and boundary-layer transition phenomena, measured using hot-film anemometers and an infrared imaging system. The analysis in this paper primarily focuses on changes in the boundary-layer state that occurred on the slats, main element, and fore flap as a result of changes in flap setting and/or flight condition. Following a detailed description of the experiment, the boundary-layer state phenomenon will be discussed based on data measured during these recent flight experiments.

vanDam, C. P.↗

Effect of particle velocity fluctuations on the inertia coupling in two-phase flow

Consistent forms for the interfacial force, the interfacial pressure, the Reynolds stresses and the particle stress have been derived for the inviscid, irrotational incompressible flow of fluid in a dilute suspension of spheres. The particles are assumed to have a velocity distribution, giving rise to an effective pressure and stress in the particle phase. The velocity fluctuations also contribute in the fluid Reynolds stress and in the (elastic) stress field inside the spheres. The relation of these constitutive equations to the force on an individual sphere is discussed.

Drew, Donald A.↗

Determination of Specific Forces and Tool Deflections in Micro-milling of Ti-6Al-4V alloy using Finite Element Simulations and Analysis

Titanium alloys offer superb properties in strength, corrosion resistance and biocompatibility and are commonly utilized in medical devices and implants. Micro-end milling process is a direct and rapid fabrication method for manufacturing medical devices and implants in titanium alloys. Process performance and quality depend upon an understanding of the relationship between cutting parameters and forces and resultant tool deflections to avoid tool breakage. For this purpose, FE simulations of chip formation during micro-end milling of Ti-6Al-4V alloy with an ultra-fine grain solid carbide two-flute micro-end mill are investigated using DEFORM software.At first, specific forces in tangential and radial directions of cutting during micro-end milling for varying feed advance and rotational speeds have been determined using designed FE simulations for chip formation process. Later, these forces are applied to the micro-end mill geometry along the axial depth of cut in 3D analysis of ABAQUS. Consequently, 3D distributions for tool deflections and von Misses stress are determined. These analyses will yield in establishing integrated multi-physics process models for high performance micro-end milling and a leap-forward to process improvements.

36 MATERIALS SCIENCE↗

Panel flutter in a low-density atmosphere

The problem of panel flutter is considered in the case of a free-molecule flow, the effect of the aerodynamic shear stress being incorporated into the structural model through distributed longitudinal and bending moment loads. This kind of analysis is relevant in the case of hypersonic flight vehicles, like the NASP, especially because in these conditions the shear stress can be expected to be considerably larger that the pressure at a given point. The aerodynamic loading is derived assuming a quasi-steady approximation. Two important parameters are given by alpha-m, the 'momentum accommodation coefficient', and Theta, the temperature ratio between the panel temperature and the temperature of the undisturbed flow. For high enough values of Theta the variation of the linear flutter parameter with alpha-m is close to linear. Comparison with continuum theory, given by linear piston theory, depends on the values of Theta and alpha-m considered. Finally, it is shown that buckling with respect to a uniform distributed longitudinal load is stabilizing.

Resende, Hugo B.↗

Effect of temperature and geometric parameters on elastic properties of tungsten nanowire: A molecular dynamics study

Tungsten is a promising material and has potential use as battery anode. Tungsten nanowires are gaining attention from researchers all over the world for this wide field of application. In this paper, we investigated effect of temperature and geometric parameters (diameter and aspect ratio) on elastic properties of Tungsten nanowire. Aspect ratios (length to diameter ratio) considered are 8:1, 10:1, and 12:1 while diameter of the nanowire is varied from 1-4 nm. For 2 nm diameter sample (aspect ratio 10:1), temperature is varied (10 K ~ 1500 K) to observe elastic behavior of Tungsten nanowire under uniaxial tensile loading. EAM potential is used for molecular dynamic simulation. We applied constant strain rate of 10{sup 9} s{sup −1} to deform the nanowire. Elastic behavior is expressed through stress vs. strain plot. We also investigated the fracture mechanism of tungsten nanowire and radial distribution function. Investigation suggests peculiar behavior of Tungsten nanowire in nano-scale with double peaks in stress vs. strain diagram. Necking before final fracture suggests that actual elastic behavior of the material is successfully captured through atomistic modeling.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

SCARE: A post-processor program to MSC/NASTRAN for the reliability analysis of structural ceramic components

A computer program was developed for calculating the statistical fast fracture reliability and failure probability of ceramic components. The program includes the two-parameter Weibull material fracture strength distribution model, using the principle of independent action for polyaxial stress states and Batdorf's shear-sensitive as well as shear-insensitive crack theories, all for volume distributed flaws in macroscopically isotropic solids. Both penny-shaped cracks and Griffith cracks are included in the Batdorf shear-sensitive crack response calculations, using Griffith's maximum tensile stress or critical coplanar strain energy release rate criteria to predict mixed mode fracture. Weibull material parameters can also be calculated from modulus of rupture bar tests, using the least squares method with known specimen geometry and fracture data. The reliability prediction analysis uses MSC/NASTRAN stress, temperature and volume output, obtained from the use of three-dimensional, quadratic, isoparametric, or axisymmetric finite elements. The statistical fast fracture theories employed, along with selected input and output formats and options, are summarized. An example problem to demonstrate various features of the program is included.

Gyekenyesi, J. P.↗

SCARE - A postprocessor program to MSC/NASTRAN for reliability analysis of structural ceramic components

A computer program was developed for calculating the statistical fast fracture reliability and failure probability of ceramic components. The program includes the two-parameter Weibull material fracture strength distribution model, using the principle of independent action for polyaxial stress states and Batdorf's shear-sensitive as well as shear-insensitive crack theories, all for volume distributed flaws in macroscopically isotropic solids. Both penny-shaped cracks and Griffith cracks are included in the Batdorf shear-sensitive crack response calculations, using Griffith's maximum tensile stress or critical coplanar strain energy release rate criteria to predict mixed mode fracture. Weibull material parameters can also be calculated from modulus of rupture bar tests, using the least squares method with known specimen geometry and fracture data. The reliability prediction analysis uses MSC/NASTRAN stress, temperature and volume output, obtained from the use of three-dimensional, quadratic, isoparametric, or axisymmetric finite elements. The statistical fast fracture theories employed, along with selected input and output formats and options, are summarized. An example problem to demonstrate various features of the program is included.

Gyekenyesi, J. P.↗

Estrogen induced concentration dependent differential gene expression in human breast cancer (MCF7) cells: Role of transcription factors

Highlights: •Estradiol (E2) at low dose induced cell proliferation in breast cancer cells. •E2 at high concentration induced cell stress in breast cancer cells. •Estrogen receptor physically interacts only with a few transcription factors. •Differential expression of genes with Oct-1 binding sites increased under stress. •Transcription factor binding sites showed distinct spatial distribution on genes. -- Abstract: Background: Breast cancer cells respond to estrogen in a concentration dependent fashion, resulting in proliferation or apoptosis. The mechanism of this concentration dependent differential outcome is not well understood yet. Methodology: Meta-analysis of the expression data of MCF7 cells treated with low (1 nM) or high (100 nM) dose of estradiol (E2) was performed. We identified genes differentially expressed at the low or the high dose, and examined the nature of regulatory elements in the vicinity of these genes. Specifically, we looked for the difference in the presence, abundance and spatial distribution of binding sites for estrogen receptor (ER) and selected transcription factors (TFs) in the genomic region up to 25 kb upstream and downstream from the transcription start site (TSS) of these genes. Results: It was observed that at high dose E2 induced the expression of stress responsive genes, while at low dose, genes involved in cell cycle were induced. We found that the occurrence of transcription factor binding regions (TFBRs) for certain factors such as Sp1 and SREBP1 were higher on regulatory regions of genes expressed at low dose. At high concentration of E2, genes with a higher frequency of Oct-1 binding regions were predominantly involved. In addition, there were differences in the spatial distribution pattern of the TFBRs in the genomic regions among the two sets of genes. Discussion: E2 induced predominantly proliferative/metabolic response at low concentrations; but at high concentration, stress–rescue responses were induced. At high E2 concentration, classical genomic pathway involving ER binding to the regulatory regions was reduced, and alternate or indirect activation of genes through Oct-1 became more prominent.

60 APPLIED LIFE SCIENCES↗

Dry Sliding Wear Resistance of Cobalt Boride Coatings Formed on ASTM F1537 Alloy

New results about the wear resistance of CoB-Co{sub 2}B coatings under dry sliding conditions were estimated in this work. The cobalt boride coatings were developed at the surface of the ASTM F1537 alloy by means of the powder-pack boriding process using two experimental conditions: 1223 K with 6 h of exposure and 1273 K with 10 h of exposure. Before the sliding wear tests, Vickers depth-sensing microindentation tests were conducted on the cross section of the cobalt boride coatings to estimate the distribution of hardness, Young’s modulus, and residual stresses. Otherwise, the sliding wear tests were performed on both boriding conditions and on the untreated material, using a ball-on-flat configuration comprised of an alumina ball as a counterpart with applied loads between 5 and 20 N. The wear rates of the borided ASTM F1537 alloy were ranged between 4.02 and 8.91 × 10{sup −6} mm{sup 3} N{sup −1} m{sup −1} compared with the values of the untreated material (13.90 and 15.78 × 10{sup −6} mm{sup 3} N{sup −1} m{sup −1}) for the overall set of experimental conditions; nevertheless, the influence of boriding conditions (1273 K with 10 h of exposure) tended to increase the CoB coating thickness, developing a more brittle layer that decreased the sliding wear resistance at the surface of the borided ASTM F1537 alloy. Finally, the presence of failure mechanisms on the surface of the wear tracks was analyzed for both borided ASTM F1537 alloy and untreated material.

36 MATERIALS SCIENCE↗

Effect of particle characteristics on the evolution of particle size, particle morphology, and fabric of sands loaded under uniaxial compression

This work presents the results and analyses of uniaxial compression experiments performed on three silica sands. The sands have comparable particle-size distributions, but their particles differ in morphology and strength. Cylindrical samples of the three sands were compressed in a loading device placed inside an X-ray microscope (XRM) and scanned at multiple stress levels during uniaxial compression. 3D tomography data of the samples obtained from the XRM at different stress levels were then analyzed to obtain the distributions of particle size, particle morphology, and interparticle contact normals within the sample. Results indicate that: (1) the compressibility of the sands loaded under uniaxial compression is closely tied to particle morphology and strength and (2) the anisotropy in the orientations of interparticle contact normals generally increases with axial stress; however, this increase is limited by the occurrence of particle crushing in the sample.

3D X-ray computed tomography↗

Effect of noise on solid-to-liquid transition in small granular systems under shear.

The effect of noise on the solid-to-liquid transition of a dense granular assembly under planar shear is studied numerically using soft-particle molecular dynamics simulations in two dimensions. We focus on small systems in a thin planar Couette cell, examining the bistable region while increasing shear, with varying amounts of random noise, and determine statistics of the shear required for fluidization. In the absence of noise, the threshold value of the shear stress depends on the preparation of the system and has a broad distribution. However, adding force fluctuations both lowers the mean threshold value of the shear stress and decreases its variability. This behavior is interpreted as thermoactivated escape through a fluctuating barrier.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗