Search NASA⌕ Search

SEARCH · Search NASA

Results for “Trajectory optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Entry aeromaneuvering capabilities of transatmospheric vehicles

The landing footprint of a conceptual high-lift transatmospheric vehicle is defined for aeromaneuvering entry from a typical low-earth orbit. The flight strategy for trajectory construction to maximize the landing area by extending downrange and crossrange as far as possible is developed in four phases by optimal programming of the vehicle's roll angle. Trajectories that reach any given landing site were calculated with the corresponding heating rates at three critical vehicle locations (stagnation point, wing leading edge, and body centerline). An optimization methodology was developed that demonstrates the trades between crossrange, peak heating and total heat loads as a function of three key flight parameters (altitude, flight-path angle, and vehicle roll angle). The maximum extent of the landing footprint was found to be 29,690 km downrange and 6560 km crossrange. Large variations in the ballistic coefficient had negligible effect on the extent of the footprint but could significantly affect heating. However, the footprint's longitude was displaced downstream or upstream with increasing or decreasing ballistic coefficient, respectively.

Menees, Gene P.↗

An Analytical Solution for Yaw Maneuver Optimization on the International Space Station and Other Orbiting Space Vehicles

This paper presents a new method for optimizing yaw maneuvers, which are the most common large maneuvers on the International Space Station (ISS). The goal of the maneuver optimization is to find a maneuver trajectory with minimal torques acting on the vehicle during the maneuver. Therefore, the thruster firings necessary to perform the maneuver are minimized. Reduction of thruster firings saves propellant and decreases structural loads and contamination of the vehicle critical elements, thus saving the service life of the thrusters and the vehicle itself. Equations describing the pitch and roll motion needed to counteract the major torques during a yaw maneuver are obtained. Also, a yaw rate profile is suggested. In the obtained optimized case, the torques are significantly reduced. The proposed approximate analytical solution does not require extensive computer resources and, therefore, can be implemented using software onboard the ISS. As a result, the maneuver execution will be automatic. This is one of the major benefits of the simplified solution presented in this paper with respect to existing computational approaches. The suggested maneuver optimization method can be used not only for the ISS, but for other space vehicles as well.

Dobrinskaya, Tatiana↗

Vehicle control for fuel optimization

The problem of predicting the minimum fuel trajectory for a six degree of freedom vehicle which has a motion characterized by the first order differential equations of translational and rotational dynamics is considered. The thrust direction and center of gravity of the vehicle are assumed to be fixed with respect to the vehicle. Thrust magnitude and the control moment are used as control variables and appear linearly in the equation of motion. Pontryagin's Maximum Principle is used to solve the variational problem. With this formulation, the extremal controls are bang-bang with the exception of the singular case.

Dannenberg, K. D.↗

Robust Trajectory Design for Rendezvous in a Near Rectilinear Halo Orbit

Future NASA Artemis missions will require complex docking plans between the Orion capsule and Lunar Gateway that meet predetermined safety constraints while minimizing fuel usage and state uncertainty at rendezvous. In this paper, linear covariance analysis is applied to a first order relative form of Near-Rectilinear Halo Orbit dynamics to determine the nominal trajectories and state dispersions associated with various maneuver profiles in the Sun-referenced Local Vertical Local Horizontal reference frame of the lunar Gateway. These maneuver profiles are optimized using a particle swarm optimizer and direct search algorithm to find trajectories that satisfy approach corridor, free drift, velocity magnitude, under-burn, and maneuver transfer time safety constraints to 3-sigma certainty.

Linear Covariance Analysis↗

Fuel Efficient Speed Optimization for Real-World Highway Cruising

This paper introduces an eco-driving highway cruising algorithm based on optimal control theory that is applied to a conventionally-powered connected and automated vehicle. Thanks to connectivity to the cloud and/or to infrastructure, speed limit and slope along the future route can be known with accuracy. This can in turn be used to compute the control variable trajectory that will minimize energy consumption without significantly impacting travel time. Automated driving is necessary to the implementation of this concept, because the chosen control variables (e.g., torque and gear) impact vehicle speed. An optimal control problem is built up where quadratic models are used for the powertrain. The optimization is solved by applying Pontryagin’s minimum principle, which reduces the problem to the minimization of a cost function with parameters called co-states. The proposed algorithm assumes piecewise constant slopes and speed limits, and it solves the transition vehicle speeds for each junction of such segments. In addition, a method to extract route information from digital maps is presented, which complies with the proposed optimization algorithm. The algorithms are evaluated in simulation, using Autonomie, a simulation tool for vehicle energy consumption modeling. The optimal control trajectory (e.g., torque, gear) is first computed offline. It is then applied in an open-loop fashion in online simulation, using a forward-looking model of the vehicle in Autonomie. Simulation results show over 8% fuel saving for two selected real-world routes.

Simulation and modeling, Optimization, Vehicle net↗

MColl: Monte Collocation Trajectory Design Tool

In this paper we describe a prototype low-thrust optimization software being developed at JPL. The software tool is based on a collocation algorithm where a trajectory discretization is fitted and adjusted until the underlying dynamics equations of motion are satisfied. The resulting large scale non-linear programming problem may either be optimized with IPOPT or KNITRO. The user specifies path constraints, boundary constraints, and objectives. We describe the collocation algorithm as well as various mesh refinement strategies, and apply the software tool to solve various example problems.

Grebow, Daniel J.↗

Reference Command Optimization for the Transition Flight Mode of a Lift plus Cruise Vehicle

Advanced air mobility mainly utilizes vehicles that are capable of vertical takeoff and landing (VTOL) for the simplicity of operation and large-scale deployment. However, VTOL vehicles need specialized trajectory and command design for the transition phase, where the vehicles transition between rotor-borne flight and wing-borne flight. Since VTOL vehicles are commonly designed as over-actuated systems for redundancy, one challenge that arises is actuator ambiguity, where it is unclear how to uniquely command actuators for the VTOL vehicle to track a given trajectory. We propose a method to design optimal reference commands for the transition mode. By formulating an 𝑙 1 -norm cost function on the rotor thrusts of the vehicle, we can achieve economical operation of the rotors such that they only operate when necessary and efficiently utilize the aerodynamics to save energy from reduced rotor actuation. We validate our approach in simulations and show its benefit compared to the commonly used differential flatness-based method.

John L Bullock↗

Improved sliced velocity map imaging apparatus optimized for H photofragments

Time-sliced velocity map imaging (SVMI), a high-resolution method for measuring kinetic energy distributions of products in scattering and photodissociation reactions, is challenging to implement for atomic hydrogen products. We describe an ion optics design aimed at achieving SVMI of H fragments in a broad range of kinetic energies (KE), from a fraction of an electronvolt to a few electronvolts. In order to enable consistently thin slicing for any imaged KE range, an additional electrostatic lens is introduced in the drift region for radial magnification control without affecting temporal stretching of the ion cloud. Time slices of {approx}5 ns out of a cloud stretched to Greater-Than-Or-Slanted-Equal-To 50 ns are used. An accelerator region with variable dimensions (using multiple electrodes) is employed for better optimization of radial and temporal space focusing characteristics at each magnification level. The implemented system was successfully tested by recording images of H fragments from the photodissociation of HBr, H{sub 2}S, and the CH{sub 2}OH radical, with kinetic energies ranging from <0.4 eV to >3 eV. It demonstrated KE resolution Less-Than-Or-Equivalent-To 1%-2%, similar to that obtained in traditional velocity map imaging followed by reconstruction, and to KE resolution achieved previously in SVMI of heavier products. We expect it to perform just as well up to at least 6 eV of kinetic energy. The tests showed that numerical simulations of the electric fields and ion trajectories in the system, used for optimization of the design and operating parameters, provide an accurate and reliable description of all aspects of system performance. This offers the advantage of selecting the best operating conditions in each measurement without the need for additional calibration experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Particle Swarm Optimization Toolbox

The Particle Swarm Optimization Toolbox is a library of evolutionary optimization tools developed in the MATLAB environment. The algorithms contained in the library include a genetic algorithm (GA), a single-objective particle swarm optimizer (SOPSO), and a multi-objective particle swarm optimizer (MOPSO). Development focused on both the SOPSO and MOPSO. A GA was included mainly for comparison purposes, and the particle swarm optimizers appeared to perform better for a wide variety of optimization problems. All algorithms are capable of performing unconstrained and constrained optimization. The particle swarm optimizers are capable of performing single and multi-objective optimization. The SOPSO and MOPSO algorithms are based on swarming theory and bird-flocking patterns to search the trade space for the optimal solution or optimal trade in competing objectives. The MOPSO generates Pareto fronts for objectives that are in competition. A GA, based on Darwin evolutionary theory, is also included in the library. The GA consists of individuals that form a population in the design space. The population mates to form offspring at new locations in the design space. These offspring contain traits from both of the parents. The algorithm is based on this combination of traits from parents to hopefully provide an improved solution than either of the original parents. As the algorithm progresses, individuals that hold these optimal traits will emerge as the optimal solutions. Due to the generic design of all optimization algorithms, each algorithm interfaces with a user-supplied objective function. This function serves as a "black-box" to the optimizers in which the only purpose of this function is to evaluate solutions provided by the optimizers. Hence, the user-supplied function can be numerical simulations, analytical functions, etc., since the specific detail of this function is of no concern to the optimizer. These algorithms were originally developed to support entry trajectory and guidance design for the Mars Science Laboratory mission but may be applied to any optimization problem.

Grant, Michael J.↗

Fuel-Efficient Descent and Landing Guidance Logic for a Safe Lunar Touchdown

The landing of a crewed lunar lander on the surface of the Moon will be the climax of any Moon mission. At touchdown, the landing mechanism must absorb the load imparted on the lander due to the vertical component of the lander's touchdown velocity. Also, a large horizontal velocity must be avoided because it could cause the lander to tip over, risking the life of the crew. To be conservative, the worst-case lander's touchdown velocity is always assumed in designing the landing mechanism, making it very heavy. Fuel-optimal guidance algorithms for soft planetary landing have been studied extensively. In most of these studies, the lander is constrained to touchdown with zero velocity. With bounds imposed on the magnitude of the engine thrust, the optimal control solutions typically have a "bang-bang" thrust profile: the thrust magnitude "bangs" instantaneously between its maximum and minimum magnitudes. But the descent engine might not be able to throttle between its extremes instantaneously. There is also a concern about the acceptability of "bang-bang" control to the crew. In our study, the optimal control of a lander is formulated with a cost function that penalizes both the touchdown velocity and the fuel cost of the descent engine. In this formulation, there is not a requirement to achieve a zero touchdown velocity. Only a touchdown velocity that is consistent with the capability of the landing gear design is required. Also, since the nominal throttle level for the terminal descent sub-phase is well below the peak engine thrust, no bound on the engine thrust is used in our formulated problem. Instead of bangbang type solution, the optimal thrust generated is a continuous function of time. With this formulation, we can easily derive analytical expressions for the optimal thrust vector, touchdown velocity components, and other system variables. These expressions provide insights into the "physics" of the optimal landing and terminal descent maneuver. These insights could help engineers to achieve a better "balance" between the conflicting needs of achieving a safe touchdown velocity, a low-weight landing mechanism, low engine fuel cost, and other design goals. In comparing the computed optimal control results with the preflight landing trajectory design of the Apollo-11 mission, we noted interesting similarities between the two missions.

guidance logic↗

Comparison of Two Multidisciplinary Optimization Strategies for Launch-Vehicle Design

The investigation focuses on development of a rapid multidisciplinary analysis and optimization capability for launch-vehicle design. Two multidisciplinary optimization strategies in which the analyses are integrated in different manners are implemented and evaluated for solution of a single-stage-to-orbit launch-vehicle design problem. Weights and sizing, propulsion, and trajectory issues are directly addressed in each optimization process. Additionally, the need to maintain a consistent vehicle model across the disciplines is discussed. Both solution strategies were shown to obtain similar solutions from two different starting points. These solutions suggests that a dual-fuel, single-stage-to-orbit vehicle with a dry weight of approximately 1.927 x 10(exp 5)lb, gross liftoff weight of 2.165 x 10(exp 6)lb, and length of 181 ft is attainable. A comparison of the two approaches demonstrates that treatment or disciplinary coupling has a direct effect on optimization convergence and the required computational effort. In comparison with the first solution strategy, which is of the general form typically used within the launch vehicle design community at present, the second optimization approach is shown to he 3-4 times more computationally efficient.

Braun, R. D.↗

OSIRIS-REx Extended Mission Trajectory Design & Target Search

After jettisoning its Sample Return Capsule (SRC) containing regolith samples from the near-Earth asteroid (101955) Bennu to Earth in September 2023, the Origins, Spectral Interpretation, Resource Identification, and Security–Regolith Explorer (OSIRIS-REx) spacecraft will perform a divert maneuver and safely fly by Earth at an altitude of 250 km. SRC return and the divert maneuver officially mark the completion of the spacecraft’s primary mission; however, it will continue on in heliocentric orbit with a nearly fully-functional instrument suite and enough propellant for nearly 600 m/s Delta-V. The post-Earth flyby trajectory fortuitously enables an exciting extended mission opportunity: rendezvous with the near-Earth asteroid (99942)Apophis immediately following its historic Earth close approach in April 2029. In this paper, we detail the discovery, optimization, and analysis of the Apophis rendezvous trajectory for an extended OSIRIS-REx mission. We also present the technical approach for an alternate target search and corresponding results, assessing the alternate trajectories compared to the baseline Apophis rendezvous from a trajectory design standpoint.

Brian Sutter↗

Beam Line Design and Beam Physics Study of Energy Recovery Linac Free Electron Laser at Peking University

Energy recovering linac (ERL) offers an attractive alternative for generating intense beams of charged particles by approaching the operational efficiency of a storage ring while maintaining the superior beam quality typical of a linear accelerator. In ERLs, the decelerated beam cancels the beam loading effects of the accelerated beam with high repetition rate. Therefore, ERLs can, in principle, accelerate very high average currents with only modest amounts of RF power. So the efficiency of RF power to beam is much higher. Furthermore, the energy of beam to dump is lower, so it will reduce dump radiation. With the successful experiments in large maximum-to-injection energy ratio up to 51:1 and high power FEL up to 14kW, the use of ERL, especially combining with superconducting RF technology, provides a potentially powerful new paradigm for generation of the charged particle beams used in MW FEL, synchrotron radiation sources, high-energy electron cooling devices and so on. The 3+1/2 DC-SC photo injector and two 9cell TESLA superconducting cavity for IR SASE FEL in PKU provides a good platform to achieve high average FEL with Energy Recovery. The work of this thesis is on Beam line design and Beam dynamics study of Energy Recovery Linac Free Electron Laser for Peking University. It is the upgrade of PKU facility, which is under construction. With ERL, this facility can work in CW mode, so it can operate high average beam current without RF power constraint in main linac and generate high average FEL power. Moreover, it provides a test facility to study the key technology in ERL. System parameters are optimized for PKU ERL-FEL. The oscillation FEL output power is studied with different bunch charge, transverse emittance, bunch length and energy spread. The theory of optimal RF power and Q{sub ext} with ERL and without ERL is analyzed and applied to PKU injector and linac including microphonic effect. pace charge effect in the injector and merger is studied for beam energy at ~5MeV. Simulation shows that in the 3+1/2 DC- C injector, there is a region the beam could be over focused by RF electromagnetic field and the transverse emittance in the transport line up to linac will increase instantly due to over focusing. In order to eliminate this effect on beam emittance, several solutions are investigated to avoid over focusing. This result is very important for beam loading experiment for low bunch charge operation. Meanwhile, different merger structures are compared in terms of error sensitivity and emittance increase with space charge effect. In recirculation beam line, a new symmetric 180{degree} arc structure is designed. It fulfills the achromatic condition and adjustable bunch compression. These two parameters are controlled by different Quads knob. With this novel structure, the recirculation lattice can achieve path length adjustment, bunch compression and decompression in a large range. With beamline error, the beam central orbit will deviate from the designed trajectory. An orbit correction system is optimized, which balances between cost and performance of orbit after correction at design level. Different methods are used to estimate its robustness. The BBU instability, especially multi-pass BBU imposed a potentially severe limitation to the average current that can be accelerated in an ERL. Simulation gives the harmful HOMs and predicts that the threshold average current in this machine is much higher than the possible operation current. This work is based on the existing facility in PKU, so it provides guidelines for the facility operation and upgrade in the future. The theoretical analysis of ERL requirement and FEL requirement on beam transport line and beam property paves the way for future ERL research.

43 PARTICLE ACCELERATORS↗

WE-AB-209-06: Dynamic Collimator Trajectory Algorithm for Use in VMAT Treatment Deliveries

Purpose: To develop advanced dynamic collimator positioning algorithms for optimal beam’s-eye-view (BEV) fitting of targets in VMAT procedures, including multiple metastases stereotactic radiosurgery procedures. Methods: A trajectory algorithm was developed, which can dynamically modify the angle of the collimator as a function of VMAT control point to provide optimized collimation of target volume(s). Central to this algorithm is a concept denoted “whitespace”, defined as area within the jaw-defined BEV field, outside of the PTV, and not shielded by the MLC when fit to the PTV. Calculating whitespace at all collimator angles and every control point, a two-dimensional topographical map depicting the tightness-of-fit of the MLC was generated. A variety of novel searching algorithms identified a number of candidate trajectories of continuous collimator motion. Ranking these candidate trajectories according to their accrued whitespace value produced an optimal solution for navigation of this map. Results: All trajectories were normalized to minimum possible (i.e. calculated without consideration of collimator motion constraints) accrued whitespace. On an acoustic neuroma case, a random walk algorithm generated a trajectory with 151% whitespace; random walk including a mandatory anchor point improved this to 148%; gradient search produced a trajectory with 137%; and bi-directional gradient search generated a trajectory with 130% whitespace. For comparison, a fixed collimator angle of 30° and 330° accumulated 272% and 228% of whitespace, respectively. The algorithm was tested on a clinical case with two metastases (single isocentre) and identified collimator angles that allow for simultaneous irradiation of the PTVs while minimizing normal tissue irradiation. Conclusion: Dynamic collimator trajectories have the potential to improve VMAT deliveries through increased efficiency and reduced normal tissue dose, especially in treatment of multiple cranial metastases, without significant safety concerns that hinder immediate clinical implementation.

60 APPLIED LIFE SCIENCES↗

Implementation of a feature selection algorithm in FARM to identify important state variables and time-invariant matrices

The FARM (Feasible Actuator Range Modifier) software module is a component of the RAVEN-based FORCE framework for analysis of Integrated Energy Systems (IES). FARM aids the HERON software module in the evaluation of the optimal dispatch for the different IES components. Set-point trajectories are required to meet limits on both production variables (i.e., the variables to be optimized such as the electrical power, the hydrogen production rate, etc.) and process variables tied to the service life of equipment (e.g., steam flowrate, vessel pressure, turbine firing temperature, etc.). To evaluate the feasibility of HERON generated set-points and to do so in an acceptable time, FARM employs reduced order models to represent the dynamic behavior of the systems to be dispatched. These surrogate models take the form of a linear dynamic system with sets of Linear Parameter Varying (LPV) matrices that are mapped to the system operating space. These matrices are derived from the trajectories of system state variables and system output variables during transients. The accuracy of LPV matrices depends on the selection of state variables. In previous reports, state variables were selected by adopting a complicated workflow requiring multiple software licenses and an advanced level of user expertise. In this report, a new workflow that automates the state variable selection process is presented. It significantly reduces the frequency of user interventions and does not require multiple software licenses. Each module in the new workflow is described in detail, and the input / output examples in each step of the workflow are provided. It was demonstrated that this workflow can greatly reduce the complexity of the state variable selection process, and that the updated FARM-Gamma and FARM-Delta validators can benefit from this workflow when solving the power dispatch problem of a representative IES test case. Finally, some code improvements that can further enhance the efficiency are suggested.

42 ENGINEERING↗

Multi-Objective Hybrid Optimal Control for Interplanetary Mission Planning

Preliminary design of low-thrust interplanetary missions is a highly complex process. The mission designer must choose discrete parameters such as the number of flybys, the bodies at which those flybys are performed and in some cases the final destination. In addition, a time-history of control variables must be chosen which defines the trajectory. There are often many thousands, if not millions, of possible trajectories to be evaluated. The customer who commissions a trajectory design is not usually interested in a point solution, but rather the exploration of the trade space of trajectories between several different objective functions. This can be a very expensive process in terms of the number of human analyst hours required. An automated approach is therefore very diserable. This work presents such as an approach by posing the mission design problem as a multi-objective hybrid optimal control problem. The method is demonstrated on a hypothetical mission to the main asteroid belt.

Optimization↗

Optimisation of dynamic reactive power sources using mesh adaptive direct search

Dynamic reactive power sources can be used to effectively mitigate the fault-induced delayed voltage recovery and transient voltage instability issues. When many var sources need to be installed at planned locations, optimisation of their sizes is a complicated non-linear optimisation problem due to its non-convexity and the dependence of the constraint on time-series trajectories of post-fault voltages. Solving this optimal sizing problem needs to utilise both a non-linear optimisation solver and a power system differential-algebraic equation solver. This study proposes a new approach for solving this problem under both a single contingency and multiple contingencies by using the mesh adaptive direct search algorithm interfaced with a power system simulator. The proposed approach is validated by case studies on a North American Eastern Interconnection model to optimise the sizes of planned STATCOMs against critical contingencies.

Huang, Weihong↗