Search NASA⌕ Search

SEARCH · Search NASA

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Static aerodynamic characteristics of a typical single-engine low-wing general aviation design for an angle-of-attack range of -8 deg to 90 deg

Static force data obtained at the NASA Ames Research Center 12 foot Pressure Tunnel are presented in plotted form for a 1/7 scale, single-engine, low-wing general aviation airplane model. The configurations tested included the basic airplane, various airfoil shapes, tail designs, fuselage strakes and fuselage modifications as well as airplane components. The test conditions included an angle-of-attack and sideslip range of -8 to 90 and -10 to 30 degrees, respectively, at a Mach number of 0.2 for Reynolds numbers of 288,000 and 3,450,000. The data are presented without analysis.

Bihrle, W., Jr.↗

Synchrophasor Data Correction under GPS Spoofing Attack: A State Estimation-Based Approach

GPS spoofing attack (GSA) has been shown to be one of the most imminent threats to almost all cyber-physical systems incorporated with the civilian GPS signal. Specifically, for our current agenda of the modernization of the power grid, this may greatly jeopardize the benefits provided by the pervasively installed phasor measurement units (PMU). In this paper, we consider the case where synchrophasor data from PMUs are compromised due to the presence of a single GSA, and show that it can be corrected by signal processing techniques. In particular, we introduce a statistical model for synchrophasorbased power system state estimation (SE), and then derive the spoofing-matched algorithms for synchrophasor data correction against GPS spoofing attack. Different testing scenarios in IEEE 14-, 30-, 57-, 118-bus systems are simulated to show the proposed algorithms’ performance on GSA detection and state estimation. Numerical results demonstrate that our proposed algorithms can consistently locate and correct the spoofed synchrophasor data with good accuracy as long as the system observability is satisfied. The accuracy of state estimation is significantly improved compared with the traditional weighted least square method and approaches the performance under the Genie-aided method.

Phasor measurement units, Global Positioning Syste↗

Static stability and control effectiveness of models 12-0 and 34-0 of the vehicle 3 configuration, volume 3

Static stability and control effectiveness characteristics of two 0.004 scale models of the vehicle 3 configuration are reported. The components investigated consisted of a single aft body, vertical/rudder, OMS pods with two interchangeable wings, four interchangeable forward bodies, four trimmers, and a spoiler. The test was conducted in 14 x 14 inch trisonic wind tunnel over a Mach number range from 0.6 to 4.96. Angles of attack from 0 to 60 degrees and angles of sideslip from -10 to 10 degrees at 0, 10, 20,30, and 40 degrees angle of attack were tested. Elevon, body flap, and speed brake deflection composed the parametric considerations. No grit was placed on the models during the test. The tabulated source data and incremental data figures are presented.

Allen, E. C.↗

Design and evaluation of a cyber‐physical testbed for improving attack resilience of power systems

Abstract A power system is a complex cyber‐physical system whose security is critical to its function. A major challenge is to model, analyse and visualise the communication backbone of the power systems concerning cyber threats. To achieve this, the design and evaluation of a cyber‐physical power system (CPPS) testbed called Resilient Energy Systems Lab (RESLab) are presented to capture realistic cyber, physical, and protection system features. RESLab is architected to be a fundamental platform for studying and improving the resilience of complex CPPS to cyber threats. The cyber network is emulated using Common Open Research Emulator (CORE), which acts as a gateway for the physical and protection devices to communicate. The physical grid is simulated in the dynamic time frame using Power World Dynamic Studio (PWDS). The protection components are modelled with both PWDS and physical devices including the SEL Real‐Time Automation Controller (RTAC). Distributed Network Protocol 3 (DNP3) is used to monitor and control the grid. Then, the design is exemplified and the tools are validated. This work presents four case studies on cyberattack and defence using RESLab, where we demonstrate false data and command injection using Man‐in‐the‐Middle and Denial of Service attacks and validate them on a large‐scale synthetic electric grid.

Sahu, Abhijeet↗

The effect of winglets on the static aerodynamic stability characteristics of a representative second generation jet transport model

A baseline wing and a version of the same wing fitted with winglets were tested. The longitudinal aerodynamic characteristics were determined through an angle-of-attack range from -1 deg to 10 deg at an angle of sideslip of 0 deg for Mach numbers of 0.750, 0.800, and 0.825. The lateral aerodynamic characteristics were determined through the same angle-of-attack range at fixed sideslip angles of 2.5 deg and 5 deg. Both configurations were investigated at Reynolds numbers of 13,000,000, per meter (4,000,000 per foot) and approximately 20,000,000 per meter (6,000,000 per foot). The winglet configuration showed slight increases over the baseline wing in static longitudinal and lateral aerodynamic stability throughout the test Mach number range for a model design lift coefficient of 0.53. Reynolds number variation had very little effect on stability.

Jacobs, P. F.↗

Wind-tunnel investigation of highly maneuverable supersonic V/STOL fighter

Results from the initial wind-tunnel test of a large-scale, highly maneuverable supersonic V/STOL fighter model in the Ames 40- by 80-foot wind tunnel are summarized. The STOL configuration which was tested combined upper surface blowing and spanwise blowing to improve the lift characteristics over a wide angle-of-attack range. A close-coupled canard was added to this configuration to create a highly maneuverable STOL aircraft. The 7.28 m (24 ft) span model was powered by two J-97 turbojet engines, each producing 9340 N (2200 lb) thrust at a pressure ratio of 2. With the nozzle flap and aileron set at 30 deg, the model produced lift coefficients greater than 4. The model was longitudinally unstable because of the forward canard position and because of the large body area of fuselage, strake, and nacelles forward of the center of gravity.

Falarski, M. D.↗

Wind-Tunnel Investigation of Subsonic Longitudinal Aerodynamic Characteristics of a Tiltable-Wing Vertical-Take-Off-and-Landing Supersonic Bomber Configuration Including Turbojet Power Effects

Jet-powered model tests were made to determine the low-speed longitudinal aerodynamic characteristics of a vertical-take-off and-landing supersonic bomber configuration. The configuration has an unique engine-wing arrangement wherein six large turbojet engines (three on each side of the fuselage) are buried in a low-aspect-ratio wing which is tilted into the vertical plane for take-off. An essentially two-dimensional variable inlet, spanning the leading edge of each wing semispan, provides air for the engines. Jet flow conditions were simulated for a range of military (nonafterburner) and afterburner turbojet-powered flight at subsonic speeds. Three horizontal tails were tested at a station down-stream of the jet exit and at three heights above the jet axes. A semi-span model was used and test parameters covered wing-fuselage incidence angles from 0 deg to 15 deg, wing angles of attack from -4 deg to 36 deg, a variable range of horizontal-tail incidence angles, and some variations in power simulation conditions. Results show that, with all horizontal tails tested, there were large variations in static stability throughout the lift range. When the wing and fuselage were alined, the model was statically stable throughout the test range only with the largest tail tested (tail span of 1.25 wing span) and only when the tail was located in the low test position which placed the tail nearest to the undeflected jet. For transition flight conditions, none of the tail configurations provided satisfactory longitudinal stability or trim throughout the lift range. Jet flow was destabilizing for most of the test conditions, and varying the jet-exit flow conditions at a constant thrust coefficient had little effect on the stability of this model. Wing leading-edge simulation had some important effects on the longitudinal aerodynamic characteristics.

Thompson, Robert F.↗

Static stability and control effectiveness of models 12-0 and 34-0 of the vehicle 3 configuration, volume 2

Static stability and control effectiveness characteristics of two 0.004 scale models of the vehicle 3 configuration are presented. The components investigated consisted of a single aft body, vertical/rudder, OMS pods with two interchangeable wings, four interchangeable forward bodies, four trimmers, and a spoiler. The test was conducted in a 14 x 14 inch trisonic wind tunnel over a Mach number range from 0.6 to 4.96. Angles of attack from 0 to 60 degrees and angles of sideslip from -10 to 10 degrees at 0, 10, 20, 30, and 40 degrees angle of attack were tested. Elevon, body flap, and speed brake deflection composed the parametric considerations. No grit was placed on the models during the test. The lateral-directional characteristics are presented along with some additional longitudinal data.

Allen, E. C.↗

Searching for fat tails in CRISPR-Cas systems: Data analysis and mathematical modeling

Understanding CRISPR-Cas systems—the adaptive defence mechanism that about half of bacterial species and most of archaea use to neutralise viral attacks—is important for explaining the biodiversity observed in the microbial world as well as for editing animal and plant genomes effectively. The CRISPR-Cas system learns from previous viral infections and integrates small pieces from phage genomes called spacers into the microbial genome. The resulting library of spacers collected in CRISPR arrays is then compared with the DNA of potential invaders. One of the most intriguing and least well understood questions about CRISPR-Cas systems is the distribution of spacers across the microbial population. Here, using empirical data, we show that the global distribution of spacer numbers in CRISPR arrays across multiple biomes worldwide typically exhibits scale-invariant power law behaviour, and the standard deviation is greater than the sample mean. We develop a mathematical model of spacer loss and acquisition dynamics which fits observed data from almost four thousand metagenomes well. In analogy to the classical ‘rich-get-richer’ mechanism of power law emergence, the rate of spacer acquisition is proportional to the CRISPR array size, which allows a small proportion of CRISPRs within the population to possess a significant number of spacers. Our study provides an alternative explanation for the rarity of all-resistant super microbes in nature and why proliferation of phages can be highly successful despite the effectiveness of CRISPR-Cas systems.

59 BASIC BIOLOGICAL SCIENCES↗

Experiments in Aircraft Roll-Yaw Control using Forebody Tangential Blowing

Advantages of flight at high angles of attack include increased maneuverability and lift capabilities. These are beneficial not only for fighter aircraft, but also for future supersonic and hypersonic transport aircraft during take-off and landing. At high angles of attack the aerodynamics of the vehicle are dominated by separation, vortex shedding and possibly vortex breakdown. These phenomena severely compromise the effectiveness of conventional control surfaces. As a result, controlled flight at high angles of attack is not feasible for current aircraft configurations. Alternate means to augment the control of the vehicle at these flight regimes are therefore necessary. The present work investigates the augmentation of an aircraft flight control system by the injection of a thin sheet of air tangentially to the forebody of the vehicle. This method, known as Forebody Tangential Blowing (FTB), has been proposed as an effective means of increasing the controllability of aircraft at high angles of attack. The idea is based on the fact that a small amount of air is sufficient to change the separation lines on the forebody. As a consequence, the strength and position of the vortices are altered causing a change on the aerodynamic loads. Although a very effective actuator, forebody tangential blowing is also highly non-linear which makes its use for aircraft control very difficult. In this work, the feasibility of using FTB to control the roll-yaw motion of a wind tunnel model was demonstrated both through simulations and experimentally. The wind tunnel model used in the experiments consists of a wing-body configuration incorporating a delta wing with 70-degree sweep angle and a cone-cylinder fuselage. The model is equipped with forebody slots through which blowing is applied. There are no movable control surfaces, therefore blowing is the only form of actuation. Experiments were conducted at a nominal angle of attack of 45 degrees. A unique apparatus that constrains the model to two degrees-of-freedom, roll and yaw, was designed and built. The apparatus was used to conduct dynamic experiments which showed that the system was unstable, its natural motion divergent. A model for the unsteady aerodynamic loads was developed based on the basic physics of the flow and results from flow visualization experiments. Parameters of the aerodynamic model were identified from experimental data. The model was validated using data from dynamic experiments. The aerodynamic model completes the equations of motion of the system which were used in the design of control laws using blowing as the only actuator. The unsteady aerodynamic model was implemented as part of the real-time vehicle control system. A control strategy using asymmetric blowing was demonstrated experimentally. A discrete vortex method was developed to help understand the main physics of the flow. The method correctly captures the interactions between forebody and wing vortices. Moreover, the trends in static loads and flow structure are correctly represented. Flow visualization results revealed the vortical structure of the flow to be asymmetric even for symmetric flight conditions. The effects of blowing, and roll and yaw angles on the flow structure were determined. It is shown that superimposing symmetric and asymmetric blowing has a linearizing effect on the actuator characteristics. Transient responses of roll and yaw moments to step input blowing were characterized, and their differences were explained based on the physical mechanisms through which these loads are generated.

Pedreiro, Nelson↗

Experimental Validation of a Resilient Monitoring and Control System

Complex, high performance, engineering systems have to be closely monitored and controlled to ensure safe operation and protect public from potential hazards. One of the main challenges in designing monitoring and control algorithms for these systems is that sensors and actuators may be malfunctioning due to malicious or natural causes. To address this challenge, this paper addresses a resilient monitoring and control (ReMAC) system by expanding previously developed resilient condition assessment monitoring systems and Kalman filter-based diagnostic methods and integrating them with a supervisory controller developed here. While the monitoring and diagnostic algorithms assess plant cyber and physical health conditions, the supervisory controller selects, from a set of candidates, the best controller based on the current plant health assessments. To experimentally demonstrate its enhanced performance, the developed ReMAC system is then used for monitoring and control of a chemical reactor with a water cooling system in a hardware-in-the-loop setting, where the reactor is computer simulated and the water cooling system is implemented by a machine condition monitoring testbed at Idaho National Laboratory. Results show that the ReMAC system is able to make correct plant health assessments despite sensor malfunctioning due to cyber attacks and make decisions that achieve best control actions despite possible actuator malfunctioning. Monitoring challenges caused by mismatches between assumed system component models and actual measurements are also identified for future work.

97 MATHEMATICS AND COMPUTING↗

Ice Accretion Roughness Variations on a Hybrid CRM65-Midspan Wing Model

Ice accretion roughness measurements were performed in the Icing Research Tunnel (IRT) at NASA Glenn Research Center for the Hybrid CRM65-Midspan model in a range of icing conditions. The Hybrid CRM65-Midspan model was chosen for this investigation because 1) the model exhibits high sweep relative to models previously explored in the roughness investigations, 2) the model has leading edge characteristics similar to wing shapes currently used in mid-size commercial airliners, and 3) the sweep and thickness ratios relate better to hybrid lifting body designs for N+2 and N+3 vehicles than other models available. The investigation consisted of multiple sets of tests which focused on 1) 0-angle of attack cases replicating the conditions employed by Anderson et al. (1998) using both Appendix C and SLD cloud conditions, 2) cases based on the “Max Scallop” case by Broeren et al. (2016) and a “High Temperature” case with cloud properties similar to the “Max Scallop” case. Additional tests were performed 1) based on the “Max Scallop” case with variations in freestream static temperature and 2) using test section speeds near 10,000-hold flight conditions. The point clouds were characterized using the approach of McClain and Kreeger (2013) for the ice roughness variations and using the approach of McClain (2016) for the mean ice thickness variations. The resulting roughness and mean thickness variations generally follow the temporal scaling previously identified using on airfoil models without sweep, but the collapse of the time progression profiles is not as tight as found for past measurements on models without sweep. LEWICE and modified panel-method predictions were used explore spatial roughness variations and to compare to the roughness correlations developed by McClain et al. (2021) for the “Max Scallop” cases.

Icing↗

Rotary balance data for a single-engine trainer design for an angle-of-attack range of 8 deg to 90 deg

Aerodynamic characteristics obtained in a rotational flow environment utilizing a rotary balance located in the Langley spin tunnel are presented in plotted form for a 1/6 scale, single engine trainer airplane model. The configurations tested included the basic airplane, various wing leading edge devices, elevator, aileron and rudder control settings as well as airplane components. Data are presented without analysis for an angle of attack range of 8 to 90 degrees and clockwise and counter-clockwise rotations.

Pantason, P.↗

Progressive Aerodynamic Model Identification From Dynamic Water Tunnel Test of the F-16XL Aircraft

Development of a general aerodynamic model that is adequate for predicting the forces and moments in the nonlinear and unsteady portions of the flight envelope has not been accomplished to a satisfactory degree. Predicting aerodynamic response during arbitrary motion of an aircraft over the complete flight envelope requires further development of the mathematical model and the associated methods for ground-based testing in order to allow identification of the model. In this study, a general nonlinear unsteady aerodynamic model is presented, followed by a summary of a linear modeling methodology that includes test and identification methods, and then a progressive series of steps suggesting a roadmap to develop a general nonlinear methodology that defines modeling, testing, and identification methods. Initial steps of the general methodology were applied to static and oscillatory test data to identify rolling-moment coefficient. Static measurements uncovered complicated dependencies of the aerodynamic coefficient on angle of attack and sideslip in the stall region making it difficult to find a simple analytical expression for the measurement data. In order to assess the effect of sideslip on the damping and unsteady terms, oscillatory tests in roll were conducted at different values of an initial offset in sideslip. Candidate runs for analyses were selected where higher order harmonics were required for the model and where in-phase and out-of-phase components varied with frequency. From these results it was found that only data in the angle-of-attack range of 35 degrees to 37.5 degrees met these requirements. From the limited results it was observed that the identified models fit the data well and both the damping-in-roll and the unsteady term gain are decreasing with increasing sideslip and motion amplitude. Limited similarity between parameter values in the nonlinear model and the linear model suggest that identifiability of parameters in both terms may be a problem. However, the proposed methodology can still be used with careful experiment design and carefully selected values of angle of attack, sideslip, amplitude, and frequency of the oscillatory data.

Murphy, Patrick C.↗

Comparison of algebraic turbulence models for afterbody flows with jet exhaust

Three-dimensional Navier-Stokes simulations have been done for transonic and low supersonic flow past a nonaxisymmetric nozzle typical of those advocated for advanced fighter airplanes. The jet exhaust is included in the calculations. The investigation compares the performance of the unmodified Baldwin-Lomax turbulence model with its performance when enhanced by the Degani-Schiff and the Goldberg modifications. Solutions are presented for Mach numbers of 0.80, 0.94, and 1.20 at 0-deg angle of attack and a Reynolds number of 20 x 10 to the 6th. The numerical results, which are compared to the wind-tunnel data, show that the three turbulence models predict considerably different shock locations, separated-flow regions, and flowfields.

Compton, William B., III↗

Viking configuration pitch damping derivatives as influenced by support interference and test technique at transonic and supersonic speeds.

Experimental studies to determine the 140-deg spherically-blunted cone configuration single degree-of-freedom damping derivative included model sting interference effects at M = 1.76 to 3.0. Minimal sting influences are noted with sting/model diameter ratios of 0.183 and effective sting lengths of 3.55 of the reference length. Increasing the ratio of sting diameter to reference length to 0.53 influences damping considerably at angles of attack from 0 to 3 deg at all Reynolds numbers but shows little or no effect at higher angles. Free-flight model wake geometries (wake neck position and size) correlate well with those from captive model tests with the small diameter sting; this adds confidence to obtaining damping derivatives through captive model testing. The damping characteristics of an early Viking configuration obtained on 11.23 and 4.35% scale models using forced and free oscillation test methods, respectively, in two different test facilities are compared. The agreement is quite good under test conditions.

Steinberg, S.↗

Substrate Binding Induces Conformational Changes in a Class A β-lactamase That Prime It for Catalysis

Here, the emergence and dissemination of bacterial resistance to β-lactam antibiotics via β-lactamase enzymes is a serious problem in clinical settings, often leaving few treatment options for infections resulting from multidrug-resistant superbugs. Understanding the catalytic mechanism of β-lactamases is important for developing strategies to overcome resistance. Binding of a substrate in the active site of an enzyme can alter the conformations and p K a s of catalytic residues, thereby contributing to enzyme catalysis. Here we report X-ray and neutron crystal structures of the class A Toho-1 β-lactamase in the apo form and an X-ray structure of a Michaelis-like complex with the cephalosporin antibiotic cefotaxime in the active site. Comparison of these structures reveals that substrate binding induces a series of changes. The side chains of conserved residues important in catalysis, Lys73 and Tyr105, and the main chain of Ser130 alter their conformations, with Nζ of Lys73 moving closer to the position of the conserved catalytic nucleophile Ser70. This movement of Lys73 closer to Ser70 is consistent with proton transfer between the two residues prior to acylation. In combination with the tightly bound catalytic water molecule located between Glu166 and the position of Ser70, the enzyme is primed for catalysis when Ser70 is activated for nucleophilic attack of the β-lactam ring. Quantum mechanical/molecular mechanical (QM/MM) free energy simulations of models of the wild-type enzyme show that proton transfer from the Nζ of Lys73 to the Oε2 atom of Glu166 is more thermodynamically favorable than when it is absent. Taken together, our findings indicate that substrate binding enhances the favorability of the initial proton transfer steps that precede the formation of the acyl-enzyme intermediate.

59 BASIC BIOLOGICAL SCIENCES↗

Science & Technology Review January/February 2010

This month's issue has the following articles: (1) Innovative Materials Rise to the Radiation Challenge - Commentary by Bruce Warner; (2) The Hunt for Better Radiation Detection - New materials will help radiation detectors pick up weak signals and accurately identify illicit radioactive sources; (3) Time-Critical Technology Identifies Deadly Bloodborne Pathogens - A portable device can simultaneously distinguish up to five bloodborne pathogens in just minutes; (4) Defending Computer Networks against Attack - A Laboratory effort takes a new approach to detecting increasingly sophisticated cyber attacks; and (5) Imaging Cargo's Inner Secrets - Livermore-University of California collaborators are modeling a new radiographic technique for identifying nuclear materials concealed inside cargo containers.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗