Search NASA⌕ Search

SEARCH · Search NASA

Results for “matrix sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Digital Twin Model for Advanced Manufacture of a Rotating Detonation Engine Injector

A digital twin material model (DTMM) of an additive manufacturing (AM) process was created to advance the state of the art in rotating detonation engine (RDE) injector design. Current RDE injectors are designed with large pressure drops, enabling a stable and repeatable combustion process. However, this comes at the cost of system efficiency. For the technology to transition to commercial fossil-based power generation, it is important to develop injectors with reduced flow losses. Low-loss injectors are difficult to design and manufacture with conventional manufacturing techniques. AM enables new design options, but the AM manufacturing process must be thoroughly understood to result in a robust design. A DTMM provides the necessary insight by defining the cause-effect relationships between process parameters, microstructure features, and properties. Therefore, a DTMM to support the design and manufacturing process was developed and applied to the design of a new additively manufactured low-loss injector. The injector combustion behavior was characterized through hot-fire tests, and mechanical performance was compared to the DTMM predictions. The two project goals were the successful development of the DTMM and the demonstration of an improved RDE injector design. The RDE injector design and DTMM developments occurred on parallel but dependent paths. The injector was designed to reduce pressure drop by increasing the cross-sectional flow area ratio between the injector air passages and the combustor annulus. This resulted in less structural material, raising the concern that thin members would be susceptible to high-cycle fatigue (HCF) under the periodic loading inherent to an RDE. It was most important for the DTMM to predict behavior in these features; therefore, the injector design concept guided the material thicknesses used in fatigue tests. The DTMM development started by manufacturing a series of coupons over the range of possible AM process variations. A design-of-experiment approach was used to select which process variable combinations gave the most efficient coverage relevant to the injector design space. The microstructure in each of these coupons was characterized, and then computational methods were used to create a numerical model of the correlation between process variables and microstructure. Next, a set of HCF samples were tested to calibrate existing models that map microstructure to HCF performance. Together, these two links formed the DTMM that calculates HCF behavior from AM process variables. Two injector prototypes were additively manufactured. The first injector design strategy aggressively pursued low-loss performance by substantially increasing the oxidizer flow area. The combination of manufacturing lead times and the fatigue testing schedule meant that the DTMM was not available when building this first prototype. Therefore, its process parameters were chosen based on a manual review of the available coupon data. This prototype was built successfully and evaluated in 58 combustion tests. Sustained detonation was achieved with remarkably reduced pressure loss, and some tests even displayed pressure loss characteristics similar to conventional gas turbine combustors. This achieved the project goal of improving RDE injector design. The second injector was manufactured according to the optimized parameters predicted by the DTMM. The flow area modifications of this injector were less aggressive than the first injector since demonstrating low pressure loss was not an objective of the second hot-fire test series. Rather, the test objective was to cause high cycle fatigue failure in the part due to periodic loading from the rotating detonation wave. The observed number of cycles to failure was to be compared to the number predicted by the DTMM and thereby assess the utility of the DTMM in component design. However, the required level of vibration was not obtained during combustion. Therefore, high cycle fatigue was not experienced in the hot-fire tests of the second injector. Fatigue data was obtained by further testing the second injector in a conventional HCF test apparatus. The injector demonstrated HCF strength above the DTMM prediction. In fact, it did not fail and testing was only discontinued due to reaching the end of the period of performance. This points to some success in the project’s primary goal of successfully developing and applying the DTMM to a component design. Implementing the DTMM recommendations for optimal processing parameters led to a part with acceptable properties. The DTMM was also shown to be an efficient correlator of data and to provide insight into the relationship between process settings, microstructure, and property performance. However, the failure of the DTMM prediction to match the experimental result of the injector fatigue test also points to the need to include significantly more data in the model development. In this project, coupons made with identical processing parameters exhibited drastically different properties from each other and from the injector part, which clearly influences the accuracy of a model that predicts performance based on parameters. Uncertainties in the build process must be quantified to develop more robust models. A denser and broader matrix of coupon process and geometry variations, several repeated builds of every point, more in-situ build process measurements, and direct observation of tensile and HCF sample microstructure (as opposed to separate microstructure specimens) are recommendations to improve future AM modeling efforts.

20 FOSSIL-FUELED POWER PLANTS↗

A practical approach to the sensitivity analysis for kinetic Monte Carlo simulation of heterogeneous catalysis

Lattice kinetic Monte Carlo simulations have become a vital tool for predictive quality atomistic understanding of complex surface chemical reaction kinetics over a wide range of reaction conditions. In order to expand their practical value in terms of giving guidelines for atomic level design of catalytic systems, it is very desirable to readily evaluate a sensitivity analysis for a given model. The result of such a sensitivity analysis quantitatively expresses the dependency of the turnover frequency, being the main output variable, on the rate constants entering the model. In the past the application of sensitivity analysis, such as Degree of Rate Control, has been hampered by its exuberant computational effort required to accurately sample numerical derivatives of a property that is obtained from a stochastic simulation method. Here in this study we present an efficient and robust three stage approach that is capable of reliably evaluating the sensitivity measures for stiff microkinetic models as we demonstrate using CO oxidation on RuO 2 (110) as a prototypical reaction. In a first step, we utilize the Fisher Information Matrix for filtering out elementary processes which only yield negligible sensitivity. Then we employ an estimator based on linear response theory for calculating the sensitivity measure for non-critical conditions which covers the majority of cases. Finally we adopt a method for sampling coupled finite differences for evaluating the sensitivity measure of lattice based models. This allows efficient evaluation even in critical regions near a second order phase transition that are hitherto difficult to control. The combined approach leads to significant computational savings over straightforward numerical derivatives and should aid in accelerating the nano scale design of heterogeneous catalysts.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structural characterization and thermal properties of polyamide 6.6/Mg, Al/adipate-LDH nanocomposites obtained by solid state polymerization

A new nanocomposite was obtained by dispersing an adipate-modified layered double hydroxide (Ad-LDH) with adipic acid and hexamethylene diamine. These samples were polymerized in the solid phase under a nitrogen flow for 200 min at 190 {sup o}C. The structural and compositional details of the nanocomposite were determined by powder X-ray diffraction (PXRD), fourier transform infrared (FTIR) spectroscopy, focused ion beam (FIB), thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The PXRD patterns and FIB images show a partially intercalated and partially exfoliated dispersion of layered crystalline materials in the polyamide 6.6 matrix. The best dispersion level is achieved in polyamide 6.6/LDH nanocomposites with low LDH loading. Some residual tactoids and particle agglomerates are also evident at high concentration. The best thermal stability of the nanocomposites is shown by the sample with 0.1% LDH content, for which it is higher than that of pure polyamide. - Graphical abstract: A new nanocomposite was obtained by compounding an adipate-modified layered double hydroxides (LDH) with adipic acid and hexamethylene diamine. These samples were polymerized in the solid phase under a nitrogen flow for 200 min at 190 {sup o}C. The nanodispersion of LDH in polyamide 6.6 may be qualitatively estimated from the analysis and PXRD patterns and FIB images. The decomposition temperature in the nanocomposite with 0.1 % LDH increases significantly compared to that for pristine PA6.6. .

36 MATERIALS SCIENCE↗

Particle Engulfment and Pushing by Solidifying Interfaces: USMP-4 One Year Report

The experiment Particle Pushing and Engulfment by Solidifying Interfaces (PEP) was conducted during the USMP-4 (United States Microgravity Payload-4) mission on board the shuttle Columbia in November 1997. This experiment has its place within the framework of a long-term scientific effort to understand the physics of particle pushing. The first flight experiment of this kind was performed with a metal matrix composite on board STS-78 in the summer of 1996. The use of opaque matrices limits the evaluation to pre-and post-flight comparison of particle locations within the sample. By using transparent matrices the interaction of one or multiple particles with an advancing solid/liquid (SL) interface can be studied in-situ. If this observation can then directly be transmitted from the orbiter to the scientists by video down-link, a real-time execution of the experiment is possible in a micro-gravity environment. Part of this experiment was an extensive training of the payload specialists to perform the experiment in orbit. This was further enhanced by the availability of video down-link and direct communication with the astronauts. Even though the PEP experiment is aimed at understanding the interaction of a liquid/solid interface with insoluble particles and thus is fundamental in scope, the prospective applications are not. Possible applications range from improved metal matrix composites to understanding and preventing frost heaving affecting roads.

Stefanescu, D. M.↗

Statistical Analysis and Geologic Evaluation of Laboratory-Derived Physical Property Data for Selected Nevada Test Site Core Samples of Non-Zeolitized Tuffs

A statistical analysis and geologic evaluation of recently acquired laboratory-derived physical property data are being performed to better understand and more precisely correlate physical properties with specific geologic parameters associated with non-zeolitized tuffs at the Nevada Test Site. Physical property data include wet and dry bulk density, grain density (i.e., specific gravity), total porosity, and effective porosity. Geologic parameters utilized include degree of welding, lithology, stratigraphy, geographic area, and matrix mineralogy (i.e., vitric versus devitrified). Initial results indicate a very good correlation between physical properties and geologic parameters such as degree of welding, lithology, and matrix mineralogy. However, physical properties appear to be independent of stratigraphy and geographic area, suggesting that the data are transferrable with regards to these two geologic parameters. Statistical analyses also indicate that the assumed grain density of 2.65 grams per cubic centimeter used to calculate porosity in some samples is too high. This results in corresponding calculated porosity values approximately 5 percent too high (e.g., 45 percent versus 40 percent), which can be significant in the lower porosity rocks. Similar analyses and evaluations of zeolitic tuffs and carbonate rock physical properties data are ongoing as well as comparisons to geophysical log values.

58 GEOSCIENCES↗

Strain-Induced Quantum Phase Transitions in Magic-Angle Graphene

In this work, we investigate the effect of uniaxial heterostrain on the interacting phase diagram of magic-angle twisted bilayer graphene. Using both self-consistent Hartree-Fock and density-matrix renormalization group calculations, we find that small strain values (ε~0.1%-0.2%) drive a zero-temperature phase transition between the symmetry-broken "Kramers intervalley-coherent" insulator and a nematic semimetal. The critical strain lies within the range of experimentally observed strain values, and we therefore predict that strain is at least partly responsible for the sample-dependent experimental observations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evidence of Skewness and Sub-Gaussian Character in Temperature-Dependent Distributions of One Million Electronic Excitation Energies in PbS Quantum Dots

Obtaining statistical distributions by sampling a large number of conformations is vital for an accurate description of temperature-dependent properties of chemical systems. However, constructing distributions with 105??106 samples is computationally challenging because of the prohibitively high computational cost of performing rst-principles quantum-mechanical calculations. In this work, we present a new technique called the Eective Stochastic Potential Conguration Interaction Singles (ESP-CIS) method to obtain excitation energies. The ESP-CIS method uses random matrix theory for the construction of an eective stochastic representation of the Fock operator and combines it with linear-response theory. Here, we perform excitation calculations on PbS quantum dots (0.75-1.75 nm) at temperatures of 200-400 K. Results from a total of 15 million excitation energy calculations (1 million samples for each of the three dots at ve dierent temperatures) revealed the distributions to be sub-Gaussian in nature with negative skewness. The distributions progressively became red-shifted with increasing temperature. The study shows that random distortions in structure from the minimum-energy geometry of these quantum dots are more likely to lower the excitation energies.

Scher, Jeremy A.↗

Measurement of Fission Product Concentration Profiles in AGR-3/4 TRISO Fuel Graphitic Matrix and Nuclear Graphites

The third Advanced Gas Reactor (AGR) irradiation experiment, AGR-3/4, was designed to investigate the migration of fission products in fuel compact graphitic matrix and reactor graphite components. Using destructive methods, radial fission product concentration profiles were measured for gamma-emitting fission products (e.g., Ag-110m, Cs-134, and Eu-154) and beta-emitting Sr-90 in irradiated graphitic and graphite components from six different AGR-3/4 irradiation capsules. These new measured concentration profiles can now be compared to non-destructive measurements and fission product transport simulations and will be used to derive new diffusivities and sorptivities to support refinement of fission product transport models and high-temperature gas-cooled reactor (HTGR) source-term analyses. Each capsule in the AGR-3/4 experiment had four fuel compacts in the middle of two concentric rings of graphitic matrix material, PCEA graphite, or IG-110 graphite. In addition to the approximately 1898 tristructural isotropic (TRISO) coated particles in each compact, there were 20 designed to fail (DTF) particles coated only in pyrocarbon so that they released fission products into the surrounding cylindrical rings of carbonaceous materials. Destructive sampling of the rings involved machining/milling material from around the circumference of the rings, collecting that material, and performing radiochemical analyses on it. Milling operations were performed in multiple steps or segments, and each segment was generally 0.508 mm (0.020 in) thick. Knowing the radial position at which each segment was milled, the volume of the milled material at each segment, and the fission product content in each segment, the radial fission product concentrations were constructed for select isotopes in each ring. Ag-110m profiles had the most variation. Some profiles were peaked at an inner or outer surface. Some were peaked at the middle of the ring wall thickness. Some increased radially outward, and some decreased radially outward. These types of variations and the fact that the measured profiles do not generally compare favorably with the transport model employed for AGR-3/4 may adversely impact the ability to extract reasonable transport parameters for this isotope. In many cases, the Cs-134 profiles decreased somewhat linearly in the outward radial direction, and in cursory comparisons, the shapes of these profiles appeared similar to those from model predictions. The step changes in concentration across the inner-outer ring gap were generally consistent with the model predictions as well. In some cases, there were local maxima in concentration at the outer surface of the rings. This suggests that fission products could have transported in the small gaps between the inner ring and the outer ring and between the outer ring and the sink ring such that some portion of a given fission product can bypass diffusion through the ring itself. The analysis of the small nubs on the outer surfaces of some of the outer rings revealed fission product concentrations in the nubs that were often higher than in the outermost segments of the rings. This further supports the hypothesis that short-circuit, gap transport occurred, causing relatively high surface concentrations on the outer surfaces of the rings. Eu-154 and Sr-90 profiles tend to have very similar shapes, suggesting that they transport via the same mechanisms. The observed profiles were indicative of a transport process where the isotopes are sorbed on the inner surface of the ring, but diffusion into the ring from that surface is quite slow. Some elevated concentrations of Sr-90 (relative to Eu-154) on the outer surface of a ring suggested that rapid, gas-gap transport of gaseous precursor Kr-90 and volatile Rb-90 could have occurred prior to their decaying to Sr-90. Overall, the Eu 154 and Sr-90 profiles were still very similar, which indicates that the transport of short-lived Sr-90 precursors is not a major effect. In some capsules, the qualitative Sr-90 behavior across the ring gaps was consistent with the model (using the available legacy Sr-90 transport parameters), but in other capsules the model was inconsistent with the measurements and seems to underestimate the amount of Sr-90 in the outer rings. The total ring Sr-90 inventories were estimated for all the rings that were subject to physical sampling. These results will be used to adjust the predicted particle and/or compact releases used in the AGR-3/4 fission product transport model. Given the different irradiation temperatures among the capsules and the rings, it was not possible to discern fundamental differences in the transport of isotopes within the different carbon materials, i.e., graphitic matrix, IG-110, or PCEA. It may be possible to do this in the course of determining transport from the concentration profiles in future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Large-scale experimental landscapes reveal distinctive effects of patch shape and connectivity on arthropod communities.

The size, shape, and isolation of habitat patches can affect organism behavior and population dynamics, but little is known about the relative role of shape and connectivity in affecting ecological communities at large spatial scales. Using six sampling sessions from July 2001 until August 2002, we collected 33,685 arthropods throughout seven 12-ha experimental landscapes consisting of clear-cut patches surrounded by a matrix of mature pine forest. Patches were explicitly designed to manipulate connectivity (via habitat corridors) independently of area and edge effects. We found that patch shape, rather than connectivity, affected ground-dwelling arthropod richness and beta diversity (i.e. turnover of genera among patches). Arthropod communities contained fewer genera and exhibited less turnover in high-edge connected and high-edge unconnected patches relative to low-edge unconnected patches of similar area. Connectivity, rather than patch shape, affected the evenness of ground-dwelling arthropod communities; regardless of patch shape, high-edge connected patches had lower evenness than low- or high-edge unconnected patches. Among the most abundant arthropod orders, increased richness in low-edge unconnected patches was largely due to increased richness of Coleoptera, whereas Hymenoptera played an important role in the lower evenness in connected patches and patterns of turnover. These findings suggest that anthropogenic habitat alteration can have distinct effects on ground-dwelling arthropod communities that arise due to changes in shape and connectivity. Moreover, this work suggests that corridors, which are common conservation tools that change both patch shape and connectivity, can have multiple effects on arthropod communities via different mechanisms, and each effect may alter components of community structure.

Diversity↗

Hygrothermal aging and recycling effects on mechanical and thermal properties of recyclable thermoplastic glass fiber composites

Abstract Glass fiber‐reinforced polymer composites are widely used in marine applications, including renewable energy devices and submarines, due to their strength‐to‐weight ratios and corrosion resistance. As sustainability becomes more important, recyclable thermoplastic composites are gaining attention in marine energy applications. These materials face harsh conditions such as high chloride water, UV radiation, pressurization, and thermal cycling, which can affect their durability and recyclability. This study examines the impact of hygrothermal aging on the recyclability of an Elium glass fiber (GF) composite. Samples were mechanically ground for recycling, and mechanical and thermal properties were compared between aged and unaged samples. After seawater aging, the tensile strength and modulus of the unaged composite dropped by 25% and 13% respectively, due to water ingress along the fiber‐matrix interface. The recycled composite showed reduced flexural strength as the long fiber composite was converted into short fibers during the process. Differential scanning calorimetry (DSC) revealed no change in glass transition temperature after aging. Weight loss (25%) was attributed to the thermal stability of the glass fibers. Dynamic mechanical analysis (DMA) showed that the storage modulus increased with aging, and fracture analysis confirmed a mixed mode of failure for aged composites. Highlights Hygrothermal aging lowers mechanical performance of Elium® GF composites. Failure mechanism tends to be matrix cracking and interface bonding. Glass transition temperature is not reduced by hygrothermal aging. Fractured composite was successfully recycled via thermoforming. Flexural strength of the recycled composite is lower.

17 WIND ENERGY↗

Molecular weight dependent structure and charge transport in MAPLE-deposited poly(3-hexylthiophene) thin films

In this work, poly(3-hexylthiophene) (P3HT) films prepared using the matrix-assisted pulsed laser evaporation (MAPLE) technique are shown to possess morphological structures that are dependent on molecular weight (MW). Specifically, the structures of low MW samples of MAPLE-deposited film are composed of crystallites/aggregates embedded within highly disordered environments, whereas those of high MW samples are composed of aggregated domains connected by long polymer chains. Additionally, the crystallite size along the side-chain (100) direction decreases, whereas the conjugation length increases with increasing molecular weight. This is qualitatively similar to the structure of spin-cast films, though the MAPLE-deposited films are more disordered. In-plane carrier mobilities in the MAPLE-deposited samples increase with MW, consistent with the notion that longer chains bridge adjacent aggregated domains thereby facilitating more effective charge transport. The carrier mobilities in the MAPLE-deposited simples are consistently lower than those in the solvent-cast samples for all molecular weights, consistent with the shorter conjugation length in samples prepared by this deposition technique.

36 MATERIALS SCIENCE↗

Sparse Representations to Replace TOFD Images in Non-destructive Testing of Materials

This paper describes a proposed method for the selection of relevant samples of ultrasonic signals during automatic material inspection. Instead of the well-known time of flight diffraction (TOFD) images, data are stored as a sparse matrix in which the elements only indicate whether a defect has been detected. This technique avoids storage of useless signals received during probe displacement in cases of low and high signal-to-noise ratios that correspond to coarse-grained and fine-grained materials, respectively. The approach is based on comparing the positions of maximum amplitudes, which are randomly located when signals only consist of noise but are in the same signal range when a defect is detected. The matrix elements are then applied as inputs to a self organizing map by neural networks to produce a normalized sparse matrix as the output, with a constant number of elements. This approach will be beneficial to enable the use of selected data in intelligent systems requiring a fixed number of inputs to characterize defects.

42 ENGINEERING↗

Development of a fast and efficient analytical technique for the isotopic analysis of fission and actinide elements in environmental matrices

An automated separation–direct analysis scheme has been developed to determine both the concentration and isotopic composition of a suite of elements down to the low picogram level in a complex silicon-based matrix. With the ultimate goal of performing rapid analysis of materials with non-natural isotopic compositions, RAPID (Rapid Analysis of Post-Irradiation Debris) consists of a high-pressure ion chromatography system directly coupled to an inductively coupled plasma mass spectrometer. The RAPID method achieves matrix exclusion and direct online analysis of the elementally separated components, yielding precise isotopic compositions for up to 40 elements in less than one hour per sample. When combined with isotope dilution, this approach shows the potential to yield elemental concentrations with low uncertainties, providing a rapid analytical method that encompasses group I and II metals, transition metals, refractory metals, platinum group metals, lanthanides, and actinides. Furthermore, the method development, robustness, sensitivity, uncertainties, and potential applications in nuclear and environmental measurements will be discussed in this paper.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Beyond the wall: High-throughput quantification of plant soluble and cell-wall bound phenolics by liquid chromatography tandem mass spectrometry

Plants accumulate several thousand of phenolic compounds, including lignins and flavonoids, which are mainly synthesized through the phenylpropanoid pathway, and play important roles in plant growth and adaptation. A novel high-throughput ultra-high performance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS) method was established to quantify the levels of 19 flavonoids and 15 other phenolic compounds, including acids, aldehydes, and alcohols. The chromatographic separation was performed in 10 minutes, allowing for the resolution of isomers such as 3-, 4-, and 5-chlorogenic acids, 4-hydroxybenzoic and salicylic acids, isoorientin and orientin, and luteolin and kaempferol. The linearity range for each compound was found to be in the low fmol to the high pmol. Furthermore, this UHPLC-MS/MS approach was shown to be very sensitive with limits of detection between 1.5 attomoles to 300 fmoles, and limits of quantification between 5 attomoles to 1,000 fmoles. Extracts from maize seedlings were used to assess the robustness of the method in terms of recovery efficiency, matrix effect, and accuracy. The biological matrix did not suppress the signal for 32 out of the 34 metabolites under investigation. Additionally, the majority of the analytes were recovered from the biological samples with an efficiency above 75 %. All flavonoids and other phenolic compounds had an intra- and inter-day accuracy within a ± 20 % range, except for coniferyl alcohol and vanillic acid. Finally, the quantification of flavonoids, free and cell wall-bound phenolics in seedlings from two maize lines with contrasting phenolic content was successfully achieved using this methodology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Oxy-fuel combustion of coal and biomass, the effect on radiative and convective heat transfer and burnout

This paper focuses on results of co-firing coal and biomass under oxy-fuel combustion conditions on the RWEn 0.5 MWt Combustion Test Facility (CTF). Results are presented of radiative and convective heat transfer and burnout measurements. Two coals were fired: a South African coal and a Russian Coal under air and oxy-fuel firing conditions. The two coals were also co-fired with Shea Meal at a co-firing mass fraction of 20%. Shea Meal was also co-fired at a mass fraction of 40% and sawdust at 20% with the Russian Coal. An IFRF Aerodynamically Air Staged Burner (AASB) was used. The thermal input was maintained at 0.5 MWt for all conditions studied. The test matrix comprised of varying the Recycle Ratio (RR) between 65% and 75% and furnace exit O{sub 2} was maintained at 3%. Carbon-in-ash samples for burnout determination were also taken. Results show that the highest peak radiative heat flux and highest flame luminosity corresponded to the lowest recycle ratio. The effect of co-firing of biomass resulted in lower radiative heat fluxes for corresponding recycle ratios. Furthermore, the highest levels of radiative heat flux corresponded to the lowest convective heat flux. Results are compared to air firing and the air equivalent radiative and convective heat fluxes are fuel type dependent. Reasons for these differences are discussed in the main text. Burnout improves with biomass co-firing under both air and oxy-fuel firing conditions and burnout is also seen to improve under oxy-fuel firing conditions compared to air. (author)

01 COAL, LIGNITE, AND PEAT↗

Cleaning up the big muddy: A meta-synthesis of the research on the social impact of dams

Scholars have been exploring the social impacts of dams for over 50 years, but a lack of systematic approaches has resulted in many research gaps remaining. This paper presents the first systematic review of the literature on the social impacts of dams. For this purpose, we built a sample of 217 articles published in the past 25 years via key word searches, expert consultations and bibliography reviews. All articles were assessed against an aggregate matrix framework on the social impact of dams, which combines 27 existing frameworks. We find that existing literature is highly biased with regard to: perspective (45% negative versus 5% positive); dam size (large dams are overrepresented); spatial focus (on the resettlement area); and temporal focus (5–10 years ex-post resettlement). Additionally, there is bias in terms of whose views are included, with those of dam developers rarely examined by scholars. These gaps need to be addressed in future research to advance our knowledge on the social impact of dams to support more transparency in the trade-offs being made in dam development decisions. - Highlights: • Very first systematic review of the research on dams' social impact • Biases in the literature identified, e. g. large dams over-studied, too much focus solely on resettlement area impacts • Implications of these biases for understanding of the topic are discussed.

13 HYDRO ENERGY↗

The formation and evolution of Ni 2 Cr precipitates in Ni–Cr model alloys as a function of stoichiometry characterized by synchrotron x-ray diffraction

Ni-based alloys containing significant amounts of Cr, may precipitate new phases during long-term service at elevated temperatures. In Ni–Cr model alloys, the formation of Ni 2 Cr has been found to impact the material properties, including the strength and ductility after isothermal aging below the critical temperature of 590°C. In this work, we quantify the formation and evolution of long-range ordering in four Ni–Cr binary model alloys (Ni/Cr = 1.8, 2.0, 2.2, 2.4) after isothermal aging up to 10,000h at temperatures between 373 and 475°C. The alloys were characterized by hardness testing and synchrotron-based x-ray diffraction to quantify the impact of Ni 2 Cr phase fraction and precipitate size on mechanical properties. After 500h of isothermal aging, the formation of Ni 2 Cr was detected in all four alloys at 475°C. In the stochiometric alloy samples (Ni/Cr = 2.0), the formation of Ni 2 Cr was found after 500 and 3000h aging at 418 and 373°C, respectively. We found that the matrix lattice contraction and Ni 2 Cr phase fraction both saturate after early aging times. This is in stark contrast to the hardness and Ni 2 Cr precipitate size that both continue to increase with increasing aging time. Our results highlight that changes in hardness correlate linearly with Ni 2 Cr precipitate size rather than phase fraction. This important structure-property relationship can potentially help define Ni–Cr-based component lifetimes directly through an understanding of how Ni 2 Cr formation impacts strength and ductility. Here, we find that a precipitation hardening model for critical resolved shear stress with weakly coupled dislocations shows good agreement with the material property changes quantified from experimental measurements.

36 MATERIALS SCIENCE↗

Laboratory study of nitrate photolysis in Antarctic snow. II. Isotopic effects and wavelength dependence

Atmospheric nitrate is preserved in Antarctic snow firn and ice. However, at low snow accumulation sites, post-depositional processes induced by sunlight obscure its interpretation. The goal of these studies (see also Paper I by Meusinger et al. [“Laboratory study of nitrate photolysis in Antarctic snow. I. Observed quantum yield, domain of photolysis, and secondary chemistry,” J. Chem. Phys. 140, 244305 (2014)]) is to characterize nitrate photochemistry and improve the interpretation of the nitrate ice core record. Naturally occurring stable isotopes in nitrate ({sup 15}N, {sup 17}O, and {sup 18}O) provide additional information concerning post-depositional processes. Here, we present results from studies of the wavelength-dependent isotope effects from photolysis of nitrate in a matrix of natural snow. Snow from Dome C, Antarctica was irradiated in selected wavelength regions using a Xe UV lamp and filters. The irradiated snow was sampled and analyzed for nitrate concentration and isotopic composition (δ{sup 15}N, δ{sup 18}O, and Δ{sup 17}O). From these measurements an average photolytic isotopic fractionation of {sup 15}ε = (−15 ± 1.2)‰ was found for broadband Xe lamp photolysis. These results are due in part to excitation of the intense absorption band of nitrate around 200 nm in addition to the weaker band centered at 305 nm followed by photodissociation. An experiment with a filter blocking wavelengths shorter than 320 nm, approximating the actinic flux spectrum at Dome C, yielded a photolytic isotopic fractionation of {sup 15}ε = (−47.9 ± 6.8)‰, in good agreement with fractionations determined by previous studies for the East Antarctic Plateau which range from −40 to −74.3‰. We describe a new semi-empirical zero point energy shift model used to derive the absorption cross sections of {sup 14}NO{sub 3}{sup −} and {sup 15}NO{sub 3}{sup −} in snow at a chosen temperature. The nitrogen isotopic fractionations obtained by applying this model under the experimental temperature as well as considering the shift in width and center well reproduced the values obtained in the laboratory study. These cross sections can be used in isotopic models to reproduce the stable isotopic composition of nitrate found in Antarctic snow profiles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗