Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

High temperature oxidation behavior of Ni-based superalloy GH202

The isothermal oxidation kinetic and oxidation behavior of Ni-based superalloy GH202 were investigated at temperatures from 800 °C to 1100 °C. The microstructure of GH202 was characterized by scanning electron microscope (SEM) and electron back-scattered diffraction (EBSD). The composition and morphologies of oxide scales of the surface and cross-section samples were examined by X-ray diffraction (XRD), electron probe microanalysis (EPMA), and SEM combined with energy-dispersive spectroscopy (EDS). The results show that the growth of the oxide scales on GH202 obeyed a parabolic law with an activation energy of 247.8 KJ·mol{sup −1} from 800 °C to 1100 °C. The continuous and dense oxide scales that formed at 800 °C and 900 °C were composed of Cr{sub 2}O{sub 3}, NiCr{sub 2}O{sub 4} and a small amount of TiO{sub 2}. Beneath the oxide scales, aluminum-rich oxides formed along the grain boundaries due to internal oxidation. After treatment at 1000 °C for 150 h, the oxide scale was separated into two layers, the outer layer with sparse holes that was mainly composed of Cr{sub 2}O{sub 3} and TiO{sub 2} and an inner layer of dense Cr{sub 2}O{sub 3}. At 1100 °C for 100 h the outer layer was spalled, due to the looser oxide scale with large blocks of TiO{sub 2} and NiCr{sub 2}O{sub 4} which provided channels for oxygen diffusion. - Highlights: •Isothermal oxidation kinetic of GH202 obeys a parabolic law from 800 °C to 1100 °C. •The activation energy of GH202 is closed to the diffusion activation of Cr{sup 3+}. •The evolution process of oxide scales from 800 °C to 1100 °C is displayed by EPMA. •The oxidation behavior of GH202 is mainly controlled by Cr{sup 3+} and Ti{sup 4+}.

36 MATERIALS SCIENCE↗

A novel ultrafine-grained Fe−22Mn−0.6C TWIP steel with superior strength and ductility

A fully recrystallized ultrafine-grained (UFG) Fe−22wt.%Mn−0.6wt.%C twinning-induced plasticity (TWIP) steel with mean grain size of 576 nm was fabricated by cold rolling and annealing process. Tensile test showed that this UFG steel possessed high yield strength of 785 MPa, and unprecedented uniform elongation of 48%. The Hall-Petch relationship was verified from the coarse-grained (CG) regime to the ultrafine-grained (UFG) regime. The microstructures at specified tensile strains were characterized by electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM). The microstructures and strain hardening behavior of the UFG TWIP steel were compared with the CG counterpart. The strong strain hardening capability of the UFG steel is supposed to be responsible for the high strength and good ductility. - Highlights: • A fully recrystallized Fe−22Mn−0.6C TWIP steel with mean grain size of 576 nm was fabricated. • The ultrafine-grained (UFG) steel exhibits strong strain-hardening capability, excellent strength and ductility. • The Hall-Petch relationship is fitted well from the CG regime to the UFG regime.

36 MATERIALS SCIENCE↗

Preparation and supercapacitor application of the single crystal nickel hydroxide and oxide nanosheets

Graphical abstract: The nickel hydroxide and nickel oxide nanosheets prepared using CTAB at room temperature exhibit a high specific capacitance, prompt charge/discharge rate. - Highlights: • The nickel hydroxide nanosheets were prepared using CTAB at room temperature. • Ni(OH){sub 2} nanosheet can be successfully converted to NiO nanosheet via calcination. • The NiO nanosheet has a specific capacitance of 388 F g{sup −1} at 5 A g{sup −1} in KOH solution. • Anneal temperature impacts capacitive properties as electrode. - Abstract: The single crystalline Ni(OH){sub 2} nanosheets were synthesized by a simple chemical precipitation method using nickel chloride as precursors and ammonia as precipitating agent. The Ni(OH){sub 2} nanosheets were successfully converted to NiO nanosheets via calcination under appropriate conditions. Analytical methods such as X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and Fourier transformed infrared (FTIR) spectra were employed to characterize the morphology and microstructure of the final products. The experimental results revealed that Ni(OH){sub 2} nanosheets were shape-preserved transformed to NiO nanosheets at 250 °C for 24 h. Ni(OH){sub 2} and NiO nanosheets were directly functionalized as supercapacitor electrodes for potential energy storage applications, whose charge–discharge properties, electrochemical impedance spectra, cyclic voltammetry, and cycle performance were examined. The experimental results show that the single-crystalline NiO nanosheets are a promising candidate for the supercapacitor electrode. They exhibit a high specific capacitance, prompt charge/discharge rate.

36 MATERIALS SCIENCE↗

How Solid-Electrolyte Interphase Forms in Aqueous Electrolytes

Solid-electrolyte interphase (SEI) is the key component that enables all advanced electrochemical devices, the best representative of which is Li-ion battery (LIB). It kinetically stabilizes electrolytes at potentials far beyond their thermodynamic stability limits, so that cell reactions could proceed reversibly. Its ad hoc chemistry and formation mechanism has been a topic under intensive investigation since the first commercialization of LIB 25 years ago. Traditionally SEI can only be formed in nonaqueous electrolytes. However, recent efforts successfully transplanted this concept into aqueous media, leading to significant expansion in the electrochemical stability window of aqueous electrolytes from 1.23 V to beyond 4.0 V. This not only made it possible to construct a series of high voltage/energy density aqueous LIBs with unprecedented safety, but also brought high flexibility and even “open configurations” that have been hitherto unavailable for any LIB chemistries. While this new class of aqueous electrolytes has been successfully demonstrated to support diversified battery chemistries, the chemistry and formation mechanism of the key component, an aqueous SEI, has remained virtually unknown. In this work, combining various spectroscopic, electrochemical and computational techniques, we rigorously examined this new interphase, and comprehensively characterized its chemical composition, microstructure and stability in battery environment. A dynamic picture obtained reveals how a dense and protective interphase forms on anode surface under competitive decompositions of salt anion, dissolved ambient gases and water molecule. By establishing basic laws governing the successful formation of an aqueous SEI, the in-depth understanding presented in this work will assist the efforts in tailor-designing better interphases that enable more energetic chemistries operating farther away from equilibria in aqueous media.

25 ENERGY STORAGE↗

Phase Segmentation in Atom-Probe Tomography Using Deep Learning-Based Edge Detection

Abstract Atom-probe tomography (APT) facilitates nano- and atomic-scale characterization and analysis of microstructural features. Specifically, APT is well suited to study the interfacial properties of granular or heterophase systems. Traditionally, the identification of the interface between, for precipitate and matrix phases, in APT data has been obtained either by extracting iso-concentration surfaces based on a user-supplied concentration value or by manually perturbing the concentration value until the iso-concentration surface qualitatively matches the interface. These approaches are subjective, not scalable, and may lead to inconsistencies due to local composition inhomogeneities. We introduce a digital image segmentation approach based on deep neural networks that transfer learned knowledge from natural images to automatically segment the data obtained from APT into different phases. This approach not only provides an efficient way to segment the data and extract interfacial properties but does so without the need for expensive interface labeling for training the segmentation model. We consider here a system with a precipitate phase in a matrix and with three different interface modalities—layered, isolated, and interconnected—that are obtained for different relative geometries of the precipitate phase. We demonstrate the accuracy of our segmentation approach through qualitative visualization of the interfaces, as well as through quantitative comparisons with proximity histograms obtained by using more traditional approaches.

47 OTHER INSTRUMENTATION↗

Thermal vibration of a rectangular single-layered graphene sheet with quantum effects

The thermal vibration of a rectangular single-layered graphene sheet is investigated by using a rectangular nonlocal elastic plate model with quantum effects taken into account when the law of energy equipartition is unreliable. The relation between the temperature and the Root of Mean Squared (RMS) amplitude of vibration at any point of the rectangular single-layered graphene sheet in simply supported case is derived first from the rectangular nonlocal elastic plate model with the strain gradient of the second order taken into consideration so as to characterize the effect of microstructure of the graphene sheet. Then, the RMS amplitude of thermal vibration of a rectangular single-layered graphene sheet simply supported on an elastic foundation is derived. The study shows that the RMS amplitude of the rectangular single-layered graphene sheet predicted from the quantum theory is lower than that predicted from the law of energy equipartition. The maximal relative difference of RMS amplitude of thermal vibration appears at the sheet corners. The microstructure of the graphene sheet has a little effect on the thermal vibrations of lower modes, but exhibits an obvious effect on the thermal vibrations of higher modes. The quantum effect is more important for the thermal vibration of higher modes in the case of smaller sides and lower temperature. The relative difference of maximal RMS amplitude of thermal vibration of a rectangular single-layered graphene sheet decreases monotonically with an increase of temperature. The absolute difference of maximal RMS amplitude of thermal vibration of a rectangular single-layered graphene sheet increases slowly with the rising of Winkler foundation modulus.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Development of attenuation and diffraction corrections for linear and nonlinear Rayleigh surface waves radiating from a uniform line source

In recent studies with nonlinear Rayleigh surface waves, harmonic generation measurements have been successfully employed to characterize material damage and microstructural changes, and found to be sensitive to early stages of damage process. A nonlinearity parameter of Rayleigh surface waves was derived and frequently measured to quantify the level of damage. The accurate measurement of the nonlinearity parameter generally requires making corrections for beam diffraction and medium attenuation. These effects are not generally known for nonlinear Rayleigh waves, and therefore not properly considered in most of previous studies. In this paper, the nonlinearity parameter for a Rayleigh surface wave is defined from the plane wave displacement solutions. We explicitly define the attenuation and diffraction corrections for fundamental and second harmonic Rayleigh wave beams radiated from a uniform line source. Attenuation corrections are obtained from the quasilinear theory of plane Rayleigh wave equations. To obtain closed-form expressions for diffraction corrections, multi-Gaussian beam (MGB) models are employed to represent the integral solutions derived from the quasilinear theory of the full two-dimensional wave equation without parabolic approximation. Diffraction corrections are presented for a couple of transmitter-receiver geometries, and the effects of making attenuation and diffraction corrections are examined through the simulation of nonlinearity parameter determination in a solid sample.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Understanding Complex Magnetic Spin Textures with Simulation-Assisted Lorentz Transmission Electron Microscopy

There is an increased interest in topologically nontrivial magnetic spin textures such as skyrmions and chiral domain-wall solitons, both from a point of fundamental physics understanding as well as potential technological interest in low-power memory applications. In order to control their behavior, it is necessary to understand their complex spin texture at the nanoscale. Lorentz transmission electron microscopy (LTEM) is a suitable technique for studying these systems due to its high spatial resolution and capability to simultaneously characterize magnetic texture and microstructure. In this work, we present the application of PyLorentz, an open-source software suite that we have developed, for quantitative image analysis of Neel-type skyrmions in thin-film heterostructures. PyLorentz enhances LTEM capabilities by enabling reconstruction of magnetic induction maps from experimental images, as well as simulating LTEM images using micromagnetic simulation data. We demonstrate this for simulated Neel skyrmions as well as experimental data from [Pt/Co/W] multilayer heterostructures. Finally, we also show how simulation-assisted LTEM analysis is crucial for understanding these complex magnetic spin textures, in which the reconstructed magnetic induction map (seen in the LTEM images) differs significantly from the magnetization configuration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Towards Multilayered Coatings of 304L Stainless Steels Using Friction Surfacing

Abstract The objective of this work is to study friction surfacing process variability when depositing multilayered coatings. This is motivated by the need to maintain deposition quality when depositing multiple friction surfacing layers, whether for repair, remanufacturing, or new part creation using this solid-state metal additive manufacturing process. In this study, 10-mm-diameter 304L stainless steel rods were used to create up to five layers of 40-mm-long coatings on 304L substrates using a constant set of processing parameters. In-process measurement of forces (X, Y, Z), flash temperature, flash geometry, layer temperature, and post-process measurement of layer geometry, microhardness, and microstructure are used to characterize changes in the friction surfacing process as more layers are deposited. It was observed that with increasing layers: layer thickness and deposition efficiency decrease; offsetting of the deposition towards the retreating side, and temperature in the deposited layer increase; and flash temperature does not change. Metallurgical analyses of friction-surfaced cross-sections revealed fine grain refinement and transformation of base austenite to strain-induced martensite. It is concluded that the process parameters need to be adjusted even after the second or third layer is deposited, corrections to the tool path are required after a couple of layers, and the measured process forces, as well as deposited layer temperature, may be useful to monitor and control the process and its instabilities.

Engineering↗

Multiscale characterization and representation of variability in ceramic matrix composites

Low density, high strength, and high creep and oxidation resistance properties of ceramic matrix composites (CMCs) make them an ideal choice for use in extreme environments in space and military applications. This paper presents a detailed characterization study of structural and manufacturing flaws in Carbon fiber Silicon-Carbide-Nitride matrix (C/SiNC) CMCs at different length-scales. Energy-dispersive spectroscopy (EDS) is used for the chemical characterization of the material’s elemental constituents. High-resolution multiscale graphs obtained from scanning electron microscope (SEM) and confocal laser scanning microscope (LSM) are used to characterize the distribution and morphology of defects at different length scales. This is followed by the classification and quantification of the common manufacturing defects. An image processing algorithm based on the image segmentation process is developed to quantify the variability of various scale-dependent architectural parameters. Finally, a three-dimensional stochastic representative volume element (SRVE) generation algorithm is developed to provide precise representations of material textures at multiple length scales. The developed algorithm accurately accounts for material features and flaws based on a range of multiscale structural and defects characterization results.

36 MATERIALS SCIENCE↗

Irradiation Creep in Graphite

An understanding of the underlying mechanisms of irradiation creep in graphite material is required to correctly interpret experimental data, explain micromechanical modeling results, and predict whole-core behavior. This project will focus on experimental microscopic data to demonstrate the mechanism of irradiation creep. High-resolution transmission electron microscopy should be able to image both the dislocations in graphite and the irradiation-induced interstitial clusters that pin those dislocations. The team will first prepare and characterize nanoscale samples of virgin nuclear graphite in a transmission electron microscope. Additional samples will be irradiated to varying degrees at the Advanced Test Reactor (ATR) facility and similarly characterized. Researchers will record microstructures and crystal defects and suggest a mechanism for irradiation creep based on the results. In addition, the purchase of a tensile holder for a transmission electron microscope will allow, for the first time, in situ observation of creep behavior on the microstructure and crystallographic defects.

Ubic, Rick↗

Wafer Test Cavity - Linking Surface Microstructure to RF Performance: a ‘Short-­Sample Test Facility’ for characterizing superconducting materials for SRF cavities

The Wafer Test cavity was designed to create a short sample test system to determine the properties of the superconducting materials and S-I-S hetero-structures. The project, funded by ARRA, was successful in accomplishing several goals to achieving a high gradient test system for SRF research and development. The project led to the design and construction of the two unique cavities that each severed unique purposes: the Wafer test Cavity and the Sapphire Test cavity. The Sapphire Cavity was constructed first to determine the properties of large single crystal sapphires in an SRF environment. The data obtained from the cavity greatly altered the design of the Wafer Cavity and provided the necessary information to ascertain the Wafer Test cavity’s performance.

42 ENGINEERING↗

IR Heat Treatment of Hybrid Steel-Al Joints

The technical objective of this CRADA is to develop and model a heat treatment process based on Infra- Red (IR) heating of a overcast Al/steel bimetallic joint to produce a T5 temper in a shorter period of time than is currently achievable and, separately, to produce a modified T6 temper for improved mechanical properties without the loss of joint integrity. IR heat treatments have been demonstrated to provide reduced processing time, reduced energy requirements, and improved material properties of Al components, including strength and elongation, relative to convective thermal heat treatment methods. A prototype IR furnace was assembled to heat treat these joints. The residual stress state of the joints were modeled in the as-cast condition, as well as the T5 and T6 condition. Neutrons were used to measure the residual stresses in the joints for various heat treatments. ORNL is uniquely equipped to partner with Vehma in the experimental evaluation and modeling of Al/steel bi-metallic joints. ORNL possesses a long history of microstructural, crystallographic and mechanical characterization of structural materials. Unique facilities at ORNL for this work include the NRSF2/HB-2B beamline at the High Flux Isotope Reactor (HFIR) for residual stress measurements with neutron diffraction, metallurgical expertise for heat treating and modeling capability of the manufacturing of these joints for residual stress prediction. All of these capabilities were utilized in this CRADA. The CRADA began in April 2011 and ended in September 2014 (41 months).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

New Mechanistic Models of Long Term Evolution of Microstructure and Mechanical Properties of Nickel Based Alloys

The report describes the development of a discrete element method (DEM) based modeling approach to quantitatively predict deformation and failure of typical nickel based superalloys. A series of experimental data, including microstructure and mechanical property characterization at 600°C, was collected for a relatively simple, model solid solution Ni-20Cr alloy (Nimonic 75) to determine inputs for the model and provide data for model validation. Nimonic 75 was considered ideal for this study because it is a certified tensile and creep reference material. A series of new DEM modeling approaches were developed to capture the complexity of metal deformation, including cubic elastic anisotropy and plastic deformation both with and without strain hardening. Our model approaches were implemented into a commercially available DEM code, PFC3D, that is commonly used by engineers. It is envisioned that once further developed, this new DEM modeling approach can be adapted to a wide range of engineering applications.

36 MATERIALS SCIENCE↗

Ductile-Phase Toughened Tungsten for Plasma Facing Materials (Final Report)

Tungsten (W) and W-alloys are the leading candidates for plasma-facing components in nuclear fusion reactors because of their high melting point, high temperature strength, good thermal conductivity and low sputtering yield, however, they are too brittle to serve a structural function. A variety of processing approaches were employed to fabricate ductile-phase-toughened (DPT) tungsten (W) composites, that includes consolidating elemental W powder with Cu- or WC-coated W-wires via spark plasma sintering (SPS). Laminated W-composites with Cu-foils were also fabricated by hot-pressing or brazing. Mechanical testing and analytical modeling were used to guide composite development. The fracture toughness of thin W plate or laminated W-composites was measured in three-point bending (3PB) at room temperature (RT). Crack arrest and crack bridging were observed for the laminated composites, and fracture resistance curves were successfully calculated. An analytical model of crack bridging was developed using the specimen geometry, matrix properties, and the stress-displacement function of a ductile reinforcement (“bridging law”) to calculate the fracture resistance curve (R-curve) and load-displacement curve (P-D curve) for any test specimen geometry. The code was also implemented to estimate the bridging law of an arbitrary composite using R-curve data. In another approach, commercially available liquid-phase sintered W alloys with four different compositions were characterized in terms of microstructure, tensile and fracture toughness at different specimen, size, geometry and testing temperatures. The room temperature (RT) average maximum load fracture toughness values (KIc or KJm ≈ 38 to 107 MPa√m) of WHA, containing only 3 to 10 wt.% of a NiFe-based ductile phase (DP), are ≈ 5 to 13 times higher than for monolithic W (≈ 8 MPa√m). Most RT tests show extensive stable ductile tearing (DT) at all W contents, including 97W (KJm ≈ 69 MPa√m), for small baseline bend bars (B=1.65mm, W=2B). Exceptions to DT, include RT elastic fracture at 97W observed in 3x larger specimens than the baseline specimens. However, the WHA KIc was still almost 5 times higher than that for monolithic W. The other exception to RT ductile tearing was for some of the 6 to 8x larger 95W alloy specimens that contained large ceramic initiating inclusions at the precrack front, along with lower DP%, with a KIc ≈ 59 MPa√m, compare to their stable DT KJm ≈ 82 MPa√m. Small specimen tests down to -196°C, to partially emulate irradiation hardening, also transition to elastic fracture at a temperature (-150 for 90W to -25ºC for 97W) that depends on the W content. However, even at -196°C, the KIc at 97W is ≈ 3 times that of monolithic W at RT. In contrast to classical ductile phase toughening by macrocrack bridging, WHA toughening mainly involves new mechanisms associated with arrest, blunting and bridging of numerous process zone microcracks. Later, these WHAs were used to fabricate W-WHA hybrid composites by coating elemental W powder on WHA using SPS. Three-point bend bars were fabricated and fracture toughness was tested at room temperature. Crack initiated and propagated from W-part to the WHA part for the well-bonded (interface) W-WHA composites for 90 and 92.5WHAs, however, crack arrested and diverted at/or through the interface for loosely bonded W-95/97WHAs with increasing load.

36 MATERIALS SCIENCE↗

Casting and Characterization of U-50Zr

Uranium alloyed with 50 wt% zirconium (U-50Zr) is a proposed light water reactor (LWR) nuclear fuel by Lightbridge Corporation (LTBR). The proposed method for making the U-50Zr alloy is to arc-melt master alloys and then remelt in a vacuum induction melter (VIM) to consolidate the material and cast into an intermediate shape. After casting, the material will eventually need to be formed into a desired fuel shape. The work discussed in this report resulted from a joint effort between Ltbr and Pacific Northwest National Laboratory (PNN) to investigate a 500g – 1kg scale casting process to produce the U-50Zr alloy in the desired δ-UZr 2 phase and characterize the impurities and microstructure that result from the casting process. Master alloys were fabricated in an arc melter, then five castings were carried out in a VIM with multiple inert coating and crucible materials to find an appropriate combination. Both ZrO 2 and graphite crucibles were used and different combinations of Y 2 O 3 , CaZrO 3 , and TiC to identify which would contain the molten metal with the least reaction. On each casting, the C, O, N, H impurities were analyzed as well as the phase by x-ray diffraction and microstructure. Of the five castings, two resulted in majority of δ-UZr 2 phase-pure material and had impurity levels within acceptable ranges. The two most successful castings utilized a graphite crucible with a TiC undercoating and a Y 2 O 3 overcoat. The O and N levels were below 1000 ppm and the C content was variable but did not result in measurable carbide formation. The highest success casting resulted in an average of 282 ppm C, 567 ppm O, 217 ppm N and 79 ppm H. This casting's crucible and inert coating material was repeated with slightly different casting parameters and resulted in higher C numbers but similar phase identification. The differences between each casting are discussed and recommendations are made for future experiments to better decide on a casting process to go forward with.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Material Properties of Zirconium Hydride Phases in Zircaloy-4 Getter Tubes Mapped by Atomic Force Microscopy

Nickel plated Zircaloy-4 tubing (“getter tubing”) is an important functional component in Tritium Producing Burnable Absorber Rods (TBPARs). Getter tubes are used to capture tritium produced during reactor operations and convert it from a gas to a solid by reacting it with Zr to form ZrHx compounds. Previous studies (PNNL-27232, TTP-8-004, and TTP-30710) on forming Zircaloy-4 hydrides demonstrated that hydride concentration gradients formed under prototypic hydriding conditions and that the microstructure of hydrides formed at 350°C is different than those formed at 500°C, a temperature typically used by the Tritium Technology Program (TTP) for getter rate loading experiments. Differences in hydride distribution, microstructure, and phases were characterize using scanning electron microscopy methods. However, the impact of these differences on material properties is not well understood. The goal of this project was to determine whether atomic force microscopy could observe subtle differences in material properties of single domains of hydride phases formed in Zircaloy-4. These properties include surface structure, hardness, thermal conductivity, and magnetic susceptibility.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗