Identification and Elemental Impurity Analysis of Heterogeneous Morphologies in Uranium Oxides Synthesized from Uranyl Fluoride Precursors
Not Available
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
PPG Industries, Inc. proposes to develop a new silica filler that can increase fuel efficiency by 2% while maximizing key performance properties in non-tread tire components compared to current carbon black/silica filler blends. In this project PPG focused on a sidewall compound. The developed compounds/components will reduce energy losses by approximately 25%, with no more than a 5% loss of resistance to degradative forces (targeting better performance). PPG plans to achieve this goal by characterizing the impact the silica filler can have on rubber properties and then tuning the silica morphology and surface chemistry for this end use. PPG will also provide guidance in optimizing the compound formulation to make the best use of this new filler. A key aspect is to understand and maintain, if not improve, the aging performance as evaluated by crack growth resistance under ozone environment. Two key strategies were used to meet the rolling resistance goal while maintaining other performance properties. The first factor was understanding the surface treatments and chemical makeup of the silica and its effects on compound performance. The second factor was using the best performing silicas and determining the optimum compound modifications to achieve the final sidewall compound performance. Using statistical analysis throughout the optimization process, it was determined that changing the silica morphology played a role in improving the reduction of tear strength while reducing rolling resistance and the improvements observed varied depending on the CB type.
Flexible DSSC is one of modification of DSSC based on its substrate. Operating at low temperature, flexible DSSC requires a binder to improve particles interconnection. This research was done to compare the morphology and performance of flexible DSSC that was produced with binder-added and binder-free. TiO{sub 2} powder, butanol, and HCl were mixed for preparation of TiO{sub 2} paste. Small amount of titanium isopropoxide as binder was added into the mixture. TiO{sub 2} paste was deposited on ITO-PET plastic substrate with area of 1x1 cm{sup 2} by doctor blade method. Furthermore, SEM, XRD, and BET characterization were done to analyze morphology and surface area of the TiO{sub 2} photoelectrode microstructures. Dyed TiO{sub 2} photoelectrode and platinum counter electrode were assembled and injected by electrolyte. In the last process, flexible DSSCs were illuminated by sun simulator to do J-V measurement. As a result, flexible DSSC containing binder showed higher performance with photoconversion efficiency of 0.31%.
We have developed an experimental system to simultaneously measure surface structure, morphology, composition, chemical state, and chemical activity for samples in gas phase environments. This is accomplished by simultaneously measuring x-ray photoelectron spectroscopy (XPS) and grazing incidence x-ray scattering in gas pressures as high as the multi-Torr regime while also recording mass spectrometry. Scattering patterns reflect near-surface sample structures from the nano-scale to the meso-scale, and the grazing incidence geometry provides tunable depth sensitivity of structural measurements. Scattered x rays are detected across a broad range of angles using a newly designed pivoting-UHV-manipulator for detector positioning. At the same time, XPS and mass spectrometry can be measured, all from the same sample spot and under ambient conditions. To demonstrate the capabilities of this system, we measured the chemical state, composition, and structure of Ag-behenate on a Si(001) wafer in vacuum and in O 2 atmosphere at various temperatures. These simultaneous structural, chemical, and gas phase product probes enable detailed insights into the interplay between the structure and chemical state for samples in gas phase environments. The compact size of our pivoting-UHV-manipulator makes it possible to retrofit this technique into existing spectroscopic instruments installed at synchrotron beamlines. Because many synchrotron facilities are planning or undergoing upgrades to diffraction limited storage rings with transversely coherent beams, a newly emerging set of coherent x-ray scattering experiments can greatly benefit from the concepts we present here.
Ni-based superalloy Haynes 230 is used in many applications such as very high temperature reactor (VHTR) or solid oxide fuel cells (SOFCs) where it is exposed to high temperature service environment. In order to improve the resistance for high temperature oxidation, the effect of crystallographic orientation on the early stage oxidation was investigated. It was demonstrated that different oxide thicknesses are formed on grains having different orientations. Comparison of electron backscatter diffraction (EBSD) orientation maps before and after oxidation at 900 °C indicates that grains near (111) orientation, especially with the deviation angle from <111> that is smaller than 20°, are more oxidation resistant than grains of other orientations. Correlation between the results of electron backscatter diffraction (EBSD) and atomic force microscopy (AFM) was used to compare the oxidation rate of grains having different crystallographic orientation. The oxidation rate was found to change with the crystallographic orientation as follows (111) < (110) < (100), also it was demonstrated that the oxidation rate changes are a nearly linear function of the angle of deviation from <111> direction. The morphology of surface oxide also depends on the orientation of grains. - Highlights: • Comparison of EBSD maps before and after oxidation allows to investigate the effect of orientation on oxidation in a more direct way; • Effect of crystallographic orientation on oxidation behavior of alloy 230 is studied by combination of EBSD and AFM; • Different thickness of oxide is formed on grain with different orientation and dependence of anisotropic oxidation behavior is discussed; • The morphology of grains is also orientation dependence.
Surface alumina coatings have been shown to be an effective way to improve the stability and cyclability of cathode materials. However, a detailed understanding of the relationship between the surface coatings and the bulk layered oxides is needed to better define the critical cathode–electrolyte interface. In this work, we systematically studied the effect of the composition of Ni-rich LiNi x Mn y Co 1–x–y O 2 (NMC) on the surface alumina coatings. Changing cathode composition from LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) to LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) was found to facilitate the diffusion of surface alumina into the bulk after high-temperature annealing. By use of a variety of spectroscopic techniques, Al was seen to have a high bulk compatibility with higher Ni/Co content, and low bulk compatibility was associated with Mn in the transition metal layer. It was also noted that the cathode composition affected the observed morphology and surface chemistry of the coated material, which has an effect on electrochemical cycling. The presence of a high surface Li concentration and strong alumina diffusion into the bulk led to a smoother surface coating on NMC811 with no excess alumina aggregated on the surface. Structural characterization of pristine NMC particles also suggests surface Co segregation, which may act to mediate the diffusion of the Al from the surface to the bulk. The diffusion of Al into the bulk was found to be detrimental to the protection function of surface coatings leading to poor overall cyclability, indicating the importance of compatibility between surface coatings and bulk oxides on the electrochemical performance of coated cathode materials.In conclusion, these results are important in developing a better coating method for synthesis of next-generation cathode materials for lithium-ion batteries.
Inverse oxide/metal catalysts have proved to be excellent systems for the generation of methanol by CO 2 hydrogenation or the partial oxidation of methane. These systems can exhibit unique structural and chemical properties due to the nano size of the oxide component and strong oxide–metal interactions. Recent studies for ZnO/Cu, CeO 2 /Cu, TiO 2/ Cu, MgO/Cu, In 2 O 3 /Cu, and In 2 O 3 /Au catalysts have shown large variations in the composition and morphology of the oxide overlayer as a function of temperature and chemical environment. These oxide–metal interfaces are able to react with CO 2 and CH 4 at room temperature, and both reactants have a strong influence on the physical and chemical properties of the catalysts. Under reaction conditions, switches between oxide–metal and metal–metal interfaces can take in the catalyst surface. A dynamic behavior that can be linked to a high selectivity for methanol production over systems such as ZnO/Cu, CeO 2 /Cu and In 2 O 3 /Au. Finally, this type of correlation deserves additional systematic studies since it could be a powerful tool for designing highly efficient catalysts for methanol synthesis.
Graphical abstract: - Highlights: • Mesoporous TiO{sub 2} nanoparticles with anatase phase were assembled on reduced graphene oxide via a template-free one-step hydrothermal method. • The TiO{sub 2}/rGO nanocomposites have better adsorption capacity and photocatalytic degradation efficiency for dyes removal. • Improved dye adsorption and photogenerated charge separation are responsible for enhanced activity. - Abstract: Mesoporous anatase phase TiO{sub 2} was assembled on reduced graphene oxide (rGO) using a template-free one-step hydrothermal process. The nanocomposites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and Brunauer–Emmett–Teller (BET) surface area. Morphology of TiO{sub 2} was related to the content of graphene oxide. TiO{sub 2}/rGO nanocomposites exhibited excellent photocatalytic activity for the photo-degradation of methyl orange. The degradation rate was 4.5 times greater than that of pure TiO{sub 2} nanoparticles. This difference was attributed to the thin two-dimensional graphene sheet. The graphene sheet had a large surface area, high adsorption capacity, and acted as a good electron acceptor for the transfer of photo-generated electrons from the conduction band of TiO{sub 2}. The enhanced surface adsorption characteristics and excellent charge transport separation were independent properties of the photocatalytic degradation process.
Porous transport layers (PTL) and their surface properties have the potential to improve the performance of proton exchange membrane water electrolyzers (PEMWE), which is imperative to reduce feedstock costs and lead to their widespread implementation. This work introduces a novel generation of titanium microporous layers (MPLs) with ultra-low thicknesses of approx. 20 um which reduces raw material costs. They also feature advanced interfacial properties tailored to maximize catalyst utilization at low Ir-loadings. The bulk morphology and surface properties of the hierarchically structured PTLs are assessed by X-ray tomographic microscopy. The low surface roughness of the MPL allows the use of thinner membranes since it minimizes possible deformations in the membrane. Cells containing the MPLs outperformed those containing state-of-the-art commercially available PTL materials by up to 100 mV at 7 A cm-2 in combination with low-loaded catalyst-coated membranes of 0.4 mgIr cm-2. Hydrogen crossover is also reduced, especially at low current densities, leading to a larger turndown ratio which can enable more cost-effective operating strategies. Finally, these rationally designed MPLs also lead to high catalyst utilization by overcoming the naturally occurring high in-plane resistance of low-loaded catalyst layers.
Graphical abstract: Display Omitted Highlights: ► Amorphous aluminophosphates can take place using yeast as template. ► A mesoporous material was obtained. ► The specific surface area after calcinations ranged between 176 and 214 m{sup 2} g{sup −1}. -- Abstract: In this study aluminophosphates have been synthesized from aluminum isopropoxide and phosphoric acid solutions using yeast cells as template. The physicochemical characterization was carried out by thermogravimetric analysis; X-ray diffraction; Fourier transform infrared; N{sub 2} adsorption–desorption isotherms; scanning electron microscopy; transmission electron microscopy and potentiometric titration with N-butylamine for determination of: thermal stability; crystalline structure; textural properties; morphology and surface acidity, respectively. The calcined powders consisted of an intimate mixture of amorphous and crystallized AlPO particles with sizes between 23 and 30 nm. The average pore size observed is 13–16 nm and the specific surface area after calcinations (at 650 °C) ranged between 176 and 214 m{sup 2} g{sup −1}.
The crystallographic orientation of a metal affects its surface energy and structure, and has profound implications for surface chemical reactions and interface engineering, which are important in areas ranging from optoelectronic device fabrication to catalysis. However, it can be very difficult and expensive to manufacture, orient, and cut single crystal metals along different crystallographic orientations, especially in the case of precious metals. One approach is to grow thin metal films epitaxially on dielectric substrates. In this work, we report on growth of Pt and Au films on MgO single crystal substrates of (100) and (110) surface orientation for use as epitaxial templates for thin film photovoltaic devices. We develop bias-assisted sputtering for deposition of oriented Pt and Au films with sub-nanometer roughness. We show that biasing the substrate decreases the substrate temperature necessary to achieve epitaxial orientation, with temperature reduction from 600 to 350 °C for Au, and from 750 to 550 °C for Pt, without use of transition metal seed layers. Additionally, this temperature can be further reduced by reducing the growth rate. Biased deposition with varying substrate bias power and working pressure also enables control of the film morphology and surface roughness.
Biochar has proven effective in the remediation of excess nitrogen from soil and water. Excess nitrogen from agricultural fields ends up in aquatic systems and leads to reduced water quality and the proliferation of invasive species. This study aimed to assess the efficiency of chemically surface-modified biochar produced from invasive Pistia stratiotes L. for the adsorption of inorganic nitrogen (NH4+ and NO3−). Biochar structure was investigated using scanning electron microscopy, energy-dispersive X-ray analysis, X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, and inductively coupled plasma mass spectrometry. The results from adsorption experiments indicate that NH4+ removal was optimal (0.8–1.3 mg N g−1) at near-neutral pH levels (6.0–7.5), while NO3− removal was optimal (0.4–0.8 mg N g−1) under acidic pH conditions (4.8–6.5) using the modified biochar. These findings highlight the significance of solution pH, biochar morphology, and surface chemistry in influencing the adsorption of NH4+ and NO3−. However, further studies are necessary to assess the potential oxidative transformation of NH4+ to NO3− by biochar, which might have contributed to the reduction in NH4+ in the aqueous phase.
We report on long-wavelength photoluminescence (PL) emission at room temperature from self-organized InAs surface quantum dots grown by gas-source molecular beam epitaxy on a GaInAsP/InP (113)B substrate. The influence of arsenic pressure conditions during growth on the PL emission of surface quantum dots is detailed as well as oxide/contamination layer formation after growth. Experimental results are in good agreement with six-band k{center_dot}p theory in the envelope function approximation.
Three-dimensional phase-field simulations of GaN growth by selective area epitaxy were performed. The model includes a crystallographic-orientation-dependent deposition rate and arbitrarily complex mask geometries. The orientation-dependent deposition rate can be determined from experimental measurements of the relative growth rates of low-index crystallographic facets. Growth on various complex mask geometries was simulated on both c-plane and a-plane template layers. Agreement was observed between simulations and experiment, including complex phenomena occurring at the intersections between facets. The sources of the discrepancies between simulated and experimental morphologies were also investigated. The model provides a route to optimize masks and processing conditions during materials synthesis for solar cells, light-emitting diodes, and other electronic and opto-electronic applications.
We demonstrate that ultralow-level Al impurities on a silicon surface can be measured by using the high-resolution grazing emission x-ray fluorescence (GEXRF) technique combined with synchrotron-radiation excitation. An Al-impurity level of about 10{sup 12} atoms/cm{sup 2} was reached by observing the Al K{alpha} x-ray fluorescence in the resonant Raman-scattering background-''free'' regime by choosing an appropriate beam energy below the Si K absorption edge. Present results show that by combining the GEXRF method with the vapor phase decomposition technique the 10{sup 7} atoms/cm{sup 2} level can be reached for Al detection on silicon. Finally, we found that the high-resolution GEXRF technique is a sensitive tool to study the morphology of surface nanostructures.
The ability to collect solid debris from the target chamber following a NIF shot has application for both capsule diagnostics, particularly for fuel-ablator mix, and measuring cross sections relevant to the Stockpile Stewardship program and nuclear astrophysics. Simulations have shown that doping the capsule with up to 10 15 atoms of an impurity not otherwise found in the capsule does not affect its performance. The dopant is an element that will undergo nuclear activations during the NIF implosion, forming radioactive species that can be collected and measured after extraction from the target chamber. For diagnostics, deuteron or alpha induced reactions can be used to probe the fuel-ablator mix. For measuring neutron cross sections, the dopant should be something that is sensitive to the 14 MeV neutrons produced through the fusion of deuterium and tritium. Developing the collector is a challenge due to the extreme environment of the NIF chamber. The collector surface is exposed to a large photon flux from x-rays and unconverted laser light before it is exposed to a debris wind that is formed from vaporized material from the target chamber center. The photons will ablate the collector surface to some extent, possibly impeding the debris from reaching the collector and sticking. In addition, the collector itself must be mechanically strong enough to withstand the large amount of energy it will be exposed to, and it should be something that will be easy to count and chemically process. In order to select the best material for the collector, a variety of different metals have been tested in the NIF chamber. They were exposed to high-energy laser shots in order to evaluate their postshot surface characterization, morphology, degree of melt, and their ability to retain debris from the chamber center. The first set of samples consisted of 1 mm thick pieces of aluminum that had been fielded in the chamber as blast shields protecting the neutron activation diagnostic. Ten of these pieces were fielded at the equator and one was fielded on the pole. The shields were analyzed using a combination of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), x-ray fluorescence (XRF), neutron activation analysis (NAA) and chemical leaching followed by mass spectrometry. On each shield, gold debris originating from the gold hohlraum was observed, as well as large quantities of debris that were present in the center of the target chamber at the time of the shot (i.e., stainless steel, indium, copper, etc.) Debris was visible in the SEM as large blobs or splats of material that had encountered the surface of the aluminum and stuck. The aluminum itself had obviously melted and condensed, and some of the large debris splats arrived after the surface had already hardened. Melt depth was determined by cross sectioning the pieces and measuring the melted surface layers via SEM. After the SEM analysis was completed, the pieces were sent for NAA at the USGS reactor and were analyzed by U. Greife at the Colorado School of Mines. The NAA showed that the majority of gold mass present on the shields was not in the form of large blobs and splats, but was present as small particulates that had most likely formed as condensed vapor. Further analysis showed that the gold was entrained in the melted aluminum surface layers and did not extend down into the bulk of the aluminum. Once the gold mass was accounted for from the NAA, it was determined that the aluminum fielded at the equator was collecting a fraction of the total gold hohlraum mass equivalent to 120% ± 10% of the solid angle subtended by the shield. The attached presentation has more information on the results of the aluminum blast shield analysis. In addition to the information given in the presentation, the surfaces of the shields have been chemically leached and submitted for mass spectrometric analysis. The results from that analysis are expected to arrive after the due date of this report and will be written up at a later time. Based on the results of the aluminum blast shield analysis, it was determined that additional materials needed to be tested as potential collectors in the NIF chamber. 1-2 mm thick pieces of tantalum, niobium, vanadium, silver, titanium, molybdenum, and graphite foil were fielded in the Wedge Range Filter (WRF) mount at a distance of 50 cm from target chamber center during the shock timing campaign. The pieces were subsequently removed and analyzed in a similar fashion to the aluminum shields. As of this writing, the pieces are still under analysis, but initial results indicate that gold debris was collected on the various materials. Currently, the pieces are being cross-sectioned so that the melt depths of each material can be compared. In addition, NAA and/or mass spectrometry will be performed in order to determine the total gold mass that was collected on each surface.
Large crystallite mesoporous MFI (ZSM-5) zeolite was synthesized by using carbon nano-powder as a secondary template. The surface properties, morphological and phase composition of the synthesized material and of the commercial ZSM-5 (Zeolyst) zeolite were studied by nitrogen porosimetry, XRD and scanning electron microscopy. The results showed that the volume of mesopores volume increases with development of a secondary mesoporosity in the structure of zeolite. The obtained zeolite supports were used to prepare molybdenum-containing catalysts for the methane aromatization by solid phase preparation technique. Based on the XPS data, molybdenum particles in these catalysts are characterized by more uniform size distribution. The formation of a secondary pore structure restrains the carbon deposit formation as well as increases the methane conversion and the yield of the aromatic compounds.
The influence of hydrothermal synthesis, thermal post-treatment at 500 Degree-Sign C and Mo content on a series of Bi{sub 1-x/3}V{sub 1-x}Mo{sub x}O{sub 4} (0.02<x<0.15) photocatalysts was investigated for methylene blue (MB) degradation and O{sub 2} evolution. Mo incorporation stabilizes the tetragonal scheelite phase of BiVO{sub 4}, thereby inducing a small blue shift of the band gap. This adverse effect can be partially compensated by incorporation of lower Mo amounts (up to ca. 4%), which stabilizes the particle morphology upon calcination. Both BiVO{sub 4}-TiO{sub 2} and BiVO{sub 4}:Mo-TiO{sub 2} heterojunction composites with TiO{sub 2} particle coatings in the 10 nm range were newly synthesized and displayed promising photocatalytic performance in MB degradation. Comparative studies with SnO{sub 2} heterojunctions revealed a superior influence of TiO{sub 2} deposition over SnO{sub 2} coating on both BiVO{sub 4} and Bi{sub 1-x/3}V{sub 1-x}Mo{sub x}O{sub 4} oxide substrates. Different synthetic guidelines for BiVO{sub 4}-based solid solutions and heterojunctions in photocatalytic wastewater treatment and water oxidation are discussed. - Graphical Abstract: The influence of Mo substitution on the structure, morphology and surface area of BiVO{sub 4} photocatalysts was investigated through hydrothermal synthesis of nanoscale Bi{sub 1-x/3}V{sub 1-x}Mo{sub x}O{sub 4} mixed oxides. Their catalytic activity in organic dye degradation and water oxidation was compared to the newly synthesized Bi{sub 1-x/3}V{sub 1-x}Mo{sub x}O{sub 4}-MO{sub 2} (M=Ti, Sn) heterojunctions. Highlights: Black-Right-Pointing-Pointer New hydrothermal approach to nanoscale Bi{sub 1-x/3}V{sub 1-x}Mo{sub x}O{sub 4} photocatalysts. Black-Right-Pointing-Pointer Influence of molybdenum substitution on organic dye degradation and water oxidation. Black-Right-Pointing-Pointer Photocatalytic activity of novel Bi{sub 1-x/3}V{sub 1-x}Mo{sub x}O{sub 4}-MO{sub 2} (M=Ti, Sn) heterojunctions.