Search NASA⌕ Search

SEARCH · Search NASA

Results for “BALLISTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Improved toughness of silicon carbide

Impact energy absorbing layers (EALs) comprised of partially densified silicon carbide were formed in situ on fully sinterable silicon carbide substrates. After final sintering, duplex silicon carbide structures resulted which were comprised of a fully sintered, high density silicon carbide substrate or core, overlayed with an EAL of partially sintered silicon carbide integrally bonded to its core member. Thermal cycling tests proved such structures to be moderately resistant to oxidation and highly resistant to thermal shock stresses. The strength of the developed structures in some cases exceeded but essentially it remained the same as the fully sintered silicon carbide without the EAL. Ballistic impact tests indicated that substantial improvements in the toughness of sintered silicon carbide were achieved by the use of the partially densified silicon carbide EALs.

Palm, J. A.↗

Planetary mission summaries. Volume 1: Introduction and overview

Tabular synopses of twelve missions are presented along with the Mariner Jupiter/Saturn 1977 mission for comparison. Mission definitions considered include: Mars Polar Orbiter; Mars Surface Sample Return; Mars Rover; Marine Jupiter/Uranus 1979 with Uranus Entry Probe; Mariner Jupiter Orbiter; Mariner Mercury Orbiter 1978; Early Mariner Comet Flyby Solar Electric Encke Slow Flyby; Mariner Encke Ballistic Flyby; Solar Electric Encke Rendezvous 1981; Venus Orbital Imaging Radar; Solar Electric Out-of-the-Eliptic Probe 1979. Technical conclusions of mission studies are given in order that these results may interact with the broader questions of scope, pace, and priorities in the planetary exploration program.

Source record↗

Some anomalies observed in wind-tunnel tests of a blunt body at transonic and supersonic speeds

An investigation of anomalies observed in wind tunnel force tests of a blunt body configuration was conducted at Mach numbers from 0.20 to 1.35 in the Langley 8-foot transonic pressure tunnel and at Mach numbers of 1.50, 1,80, and 2.16 in the Langley Unitary Plan wind tunnel. At a Mach number of 1.35, large variations occurred in axial force coefficient at a given angle of attack. At transonic and low supersonic speeds, the total drag measured in the wind tunnel was much lower than that measured during earlier ballistic range tests. Accurate measurements of total drag for blunt bodies will require the use of models smaller than those tested thus far; however, it appears that accurate forebody drag results can be obtained by using relatively large models. Shock standoff distance is presented from experimental data over the Mach number range from 1.05 to 4.34. Theory accurately predicts the shock standoff distance at Mach numbers up to 1.75.

Brooks, J. D.↗

Impact ejecta on the moon

The partitioning of energy and the distribution of the resultant ejecta on the moon is numerically modeled using a Eulerian finite difference grid. The impact of an iron meteoroid at 15 km/sec on a gabbroic anorthosite lunar crust is examined. The high speed impact induced flow is described over the entire hydrodynamic regime from a time where the peak pressures are 6 Mbar until the stresses everywhere in the flow are linearly elastic, and less than 5 kbar. Shock-induced polymorphic phase changes, (plagioclase and pyroxene to hollandite and perovskite), and the subsequent reversion to low pressure phases are demonstrated to enhance shock wave attenuation. A rate-dependent equation of state is used for describing the hysteretic effect of the phase change. Ballistic equations for a spherical planet are then applied to material with net velocity away from the moon.

Okeefe, J. D.↗

Mass fractionation of the lunar surface by solar wind sputtering

The sputtering of the lunar surface by the solar wind is examined as a possible mechanism of mass fractionation. Simple arguments based on current theories of sputtering and the ballistics of the sputtered atoms suggest that most ejected atoms will have sufficiently high energy to escape lunar gravity. However, the fraction of atoms which falls back to the surface is enriched in the heavier atomic components relative to the lighter ones. This material is incorporated into the heavily radiation-damaged outer surfaces of grains where it is subject to resputtering. Over the course of several hundred years an equilibrium surface layer, enriched in heavier atoms, is found to form. The dependence of the calculated results upon the sputtering rate and on the details of the energy spectrum of sputtered particles is investigated. It is concluded that mass fractionation by solar wind sputtering is likely to be an important phenomenon on the lunar surface.

Switkowski, Z. E.↗

Experimental hypervelocity impact into quartz sand - Distribution and shock metamorphism of ejecta

Results are presented for vertical impacts of 0.3-g cylindrical plastic projectiles into noncohesive quartz sand in which vertical and horizontal reference strate were employed by using layers of colored sand. The impacts were performed at velocities of 5.9-6.9 km/sec with a vertical gun ballistic range. The craters, 30-33 cm in diameter, reveal a radial decay of the ejecta mass per unit area with a power of -2.8 to -3.5. Material displaced from the upper 15% of the crater depth d is represented within the whole ejecta blanked, material from deeper than 28% of d is deposited inside 2 crater radii, and no material from deeper than 33% of d was ejected beyond the crater rim. Shock-metamorphosed particles (glassy agglutinates, cataclastic breccias, and comminuted quartz) amount to some 4% of the total displaced mass and indicate progressive zones of decay of shock intensity from a peak pressure of 300 kbar. The shock-metamorphosed particles and the shock-induced change in the grain size distribution of ejected samples have close analogies to the basic characteristics of the lunar regolith. Possible applications to regolith formation and to ejecta formations of large-scale impact craters are discussed.

Stoeffler, D.↗

Monte Carlo investigation of thrust imbalance of solid rocket motor pairs

The Monte Carlo method of statistical analysis is used to investigate the theoretical thrust imbalance of pairs of solid rocket motors (SRMs) firing in parallel. Sets of the significant variables are selected using a random sampling technique and the imbalance calculated for a large number of motor pairs using a simplified, but comprehensive, model of the internal ballistics. The treatment of burning surface geometry allows for the variations in the ovality and alignment of the motor case and mandrel as well as those arising from differences in the basic size dimensions and propellant properties. The analysis is used to predict the thrust-time characteristics of 130 randomly selected pairs of Titan IIIC SRMs. A statistical comparison of the results with test data for 20 pairs shows the theory underpredicts the standard deviation in maximum thrust imbalance by 20% with variability in burning times matched within 2%. The range in thrust imbalance of Space Shuttle type SRM pairs is also estimated using applicable tolerances and variabilities and a correction factor based on the Titan IIIC analysis.

Sforzini, R. H.↗

Theoretical prediction of erosive burning characteristics of solid rocket propellant based on burning rate dependence of pressure and initial temperature and its energetic characteristics

New theoretical method for prediction of erosive burning characteristics of solid propellant, using known ballistic and thermodynamic data only, is presented. Method is based on modified Lenoir-Robillard formula, and is applicable for composite and double base propellants, with or without negative erosion effect. Method is confirmed using experimental data of numerous authors.

Jojic, B.↗

Preliminary results from the Viking orbiter imaging experiment

During its first 30 orbits around Mars, the Viking orbiter took approximately 1000 photographic frames of the surface of Mars with resolutions that ranged from 100 meters to a little more than 1 kilometer. Most were of potential landing sites in Chryse Planitia and Cydonia and near Capri Chasma. Contiguous high-resolution coverage in these areas has led to an increased understanding of surface processes, particularly cratering, fluvial, and mass-wasting phenomena. Most of the surfaces examined appear relatively old, channel features abound, and a variety of features suggestive of permafrost have been identified. The ejecta patterns around large craters imply that fluid flow of ejecta occurred after ballistic deposition. Variable features in the photographed area appear to have changed little since observed 5 years ago from Mariner 9. A variety of atmospheric phenomena were observed, including diffuse morning hazes, both stationary and moving discrete white clouds, and wave clouds covering extensive areas.

Carr, M. H.↗

Launch opportunity classification of VEGA and delta V-EGA trajectories to the outer planets

Two concepts in spacecraft trajectory design which have been proposed by Hollenbeck (1975) and Bender and Friedlander (1975) are considered. Both concepts are intended for planetary missions and require an earth reencounter created by either a Venus gravity assist (VEGA) or a large midcourse impulse (delta V-EGA). In the case of outer planet missions, the new concepts offer significantly lower launch energy requirements than the direct ballistic flight mode. However, at least an additional two years flight time is needed for geometry phasing to set up the earth reencounter. A description is given of the trajectory characteristics for the two concepts. Attention is also given to the method of analysis used for the studies, aspects of trajectory generation, payload calculations, and target opportunity data.

Stancati, M. L.↗

Missions to Titan /1983-2000/ - An analysis of orbiters and entry vehicles

Mission Analysis data is presented which forms a basis for planning future missions to Titan, the seventh moon of Saturn. Four Titan mission options are studied: orbiters, probes, penetrators and landers. The generated data supports these mission modes. A comprehensive launch and trajectory analysis of earth to Saturn opportunities from 1983 to 2000 is given. Direct ballistic and Delta VEGA trajectory modes are evaluated. Orbital insertion, orbital trim, entry vehicle deployment options are all studied in parametric detail.

Hendricks, T. C.↗

The broadening of the calcium resonance line in a high-temperature helium atmosphere

The paper describes experimental measurements of the shape of the Ca I resonance line at 4227 A in a high-temperature helium atmosphere. A ballistic piston compressor was used to produce hot helium in the temperature range from 3000 to 7000 K and the number-density range from 2 to 4 by 10 to the 20th power per cu cm, which conditions approximate those postulated for the atmospheres of certain cool white-dwarf stars. The Boltzmann temperature of the calcium atoms was measured by the brightness-emissivity method, the absorption line shape was measured with a twelve-channel polychromator, and the helium kinetic temperature was calculated from the equation of an ideal gas. The observed deviation from thermodynamic equilibrium is illustrated. The value of the ratio of the damping constant to the helium number density at 5000 K is found to be 45 (+ or - 4) by 10 to the -22nd power A cu cm, or 4.7 (+ or - 0.4) by 10 to the -9th power rad/s cu cm. It is noted that no existing line-broadening calculation for the calcium-helium system is consistent with the present results. Recent studies of the 4227-A line in spectra of the sun and the white dwarf van Maanen 2 are discussed.

Driver, R. D.↗

Status of the Viking missions

A chronology of Viking 1 lander activities is presented for the first 43 sols (Martian days) of surface sampling and analysis. The orbital insertion of the second Viking spacecraft is reviewed along with the search for the second landing site. A general assessment of the planet is made on the basis of the data thus far obtained. Some of the findings reported are that: (1) there is extensive evidence of volcanism, fluvial and aeolian erosion, and deposition over the entire surface; (2) the floor of Vallis Marineris is significantly younger than the planet's surface; (3) the morphology of Martian crater ejecta is indicative of surface flow rather than ballistic deposition; (4) the rocks in the immediate vicinity of the lander are all covered by a layer of fine red dust; (5) the atmosphere is optically thick and well mixed, with suspended particles giving the sky a pink color; (6) the N and Ar isotopic ratios are different from those on earth; (7) atmospheric water vapor varies with both time of day and location; (8) the summer northern polar regions have a high water concentration in the atmosphere; (9) a large fraction of magnetic material resides in the surface; and (10) no complex organic compounds have been detected in the two samples analyzed.

Soffen, G. A.↗

Thermodynamic properties of a high pressure subcritical UF6/He gas volume (irradiated by an external source)

A computer simulation study concerning a compressed fissioning UF6 gas is presented. The compression is to be achieved by a ballistic piston compressor. Data on UF6 obtained with this compressor were incorporated in the simulation study. As a neutron source to create the fission events in the compressed gas, a fast burst reactor was considered. The conclusion is that it takes a neutron flux in excess of 10 to the 15th power n/sec sq cm to produce measurable increases in pressure and temperature, while a flux in excess of 10 to 19th power n/sq cm sec would probably damage the compressor.

Sterritt, D. E.↗

SRB-3D Solid Rocket Booster performance prediction program. Volume 1: Engineering description/users information manual

The modified Solid Rocket Booster Performance Evaluation Model (SRB-3D) was developed as an extension to the internal ballistics module of the SRB-2 performance program. This manual contains the engineering description of SRB-3D which describes the approach used to develop the 3D concept and an explanation of the modifications which were necessary to implement these concepts.

Winkler, J. C.↗

Nonlinear coupling between pulsation and convection in late type stars

A simple idealized nonlinear model applicable to long-period variable stars has been formulated which assumes that the convective envelope of M giants is composed of giant convection cells comparable in size to the stellar radius. The simplicity of this model essentially constitutes a physical analog to the strong dynamic coupling that occurs if the convective envelope of the star undergoes both modes of motion. As shown implicitly in the time scales associated with these motions, the coupling produces asymmetrical fluctuations of the entire star, the mean velocity of which is comparable to the escape velocity of the star at particular values of the ratio of the pulsation and convection time scales. It is suggested that this can account for the mass loss from late-type stars and the circumstellar dust shells that are associated extensively with long-period variables. For critical values of the pulsation and convection time scales, the solutions correspond to the rapid expansion of the entire convective envelope and are the basis of a mechanism that simulates the manner in which pulsating stars ballistically accelerate their convective shells to form planetary nebulae.

Anand, S. P. S.↗

Guidance and trajectory considerations in lunar mass transportation

Flight-mechanics problems associated with large-scale transport of lunar mass to a space colony or manufacturing facility are discussed. The proposed transport method involves launch of payloads from a mass-driver on the lunar surface, onto ballistic trajectories to a passive mass-catcher located near the L2 libration point, with the caught mass subsequently being transported to the colony. Arrival velocities at L2, sensitivities in arrival dispersion due to launch errors, and effects of launch site location are treated, via numerically integrated orbits in the restricted three-body problem. From any launch site it is possible to define a target point reached with zero dispersion due to errors in a selected component of launch velocity. Effects of lunar geometrical librations and of obliquity, as well as the conditions for biasing a trajectory away from L2 so as to reduce stationkeeping costs, are dealt with along with transfer orbits from L2 to the colony. The theory of capture and the theory of resonance lead to a colony orbit, with period approximately two weeks, reached from L2 with velocity increment as low as 9.02 m/sec.

Heppenheimer, T. A.↗

On the computational cost of approximating and recognizing noise-perturbed straight lines and quadratic arcs in the plane

Recognition of underlying straight lines and quadratic arcs in line drawings, and approximation of very noisy data by such line/curve segments, is addressed as a subproblem of the more general problem of optimum recognition of complicated line/curve drawings. Some specific algorithms are presented with extensions and interpretations for more complicated applications, and a data generation model is developed for the problem. Data are generated as a perturbation of a single underlying straight line or an elliptic or hyperbolic arc. Recursive estimation techniques, minimization of central processing unit time, decision making with controlled error probabilities, and modeling and recognition of pictures consisting of noisy curves are dealt with. Applications envisaged include: picture data compression, contour line representation in maps, intelligent data searches, and ballistic missile decoy tracking.

Cooper, D. B.↗