Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel performance analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Preliminary analysis of core heat-up for ATFs under accident conditions

The accident-tolerant fuel (ATF) system is aim at upgrading safety characteristics of the nuclear fuel and cladding in a reactor core where active cooling has been lost, and is preferable or comparable to the conventional UO{sub 2}-Zr fuel system when the reactor is in normal operation. In this paper, the improved performance of UO{sub 2}-SiC, UO{sub 2}-FeCrAl fuel systems, and of fully ceramic micro-encapsulated (FCM) fuels: FCM-SiC and FCM-FeCrAl, on the core heat-up progress in a pressurized water reactor (PWR) is analyzed by using the best-estimate system code RELAP5 and severe accident analysis program. For this purpose two accident scenarios are selected: a large break LOCA as a design base accident and an extended station blackout (SBO) severe accident. For the LBLOCA with just low-pressure safety injection, larger volumetric heat capacity and thermal conductivity of ATF materials contribute to a larger safety margin in terms of the peak cladding temperature compared with UO{sub 2}-Zr. Thanks to higher melting temperatures, FCM-SiC is failed by melting almost 1200 s later than UO{sub 2}-Zr. The accumulated production of hydrogen for ATF materials is around 10 times smaller than that for UO{sub 2}-Zr. However, high temperature oxidation of SiC cladding generates carbon monoxide which is combustible, while the melting point of FeCrAl is not high enough. In the SBO scenario with mitigation measure, the advantage of ATF is more evident. If the mitigation measure could not be taken, core heatup is inevitable for all types of fuel system, but the temperature rising of ATF core is much slower. In general, improved high-temperature properties and resistance to oxidation play important roles for ATF cores.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural Analysis of Iron-Chromium-Aluminum Samples Exposed to Loca-Type Conditions Followed by Quench

The QUENCH-19 experiment was performed to examine the behavior of FeCrAl-alloy B1236Y3 as a potential nuclear fuel cladding and accident conditions. Over the course of the test, a surrogate bundle achieved a temperature of just over 1400°C. Post-test characterization revealed that the FeCrAl formed a thin layer of aluminum oxide that protected most of the underlying cladding and surrogate fuel pin. However, a few pins were heavily corroded and even destroyed primarily by thermocouple-FeCrAl interactions and subsequent steam, FeCrAl, and ZrO 2 interactions. Absent these effects, it is suggested that FeCrAl’s performance may be acceptable under these conditions.

36 MATERIALS SCIENCE↗

Gear Test Assembly – Experimental Testing and Gear Analysis (FY2021 Year End Report)

The Gear Test Assembly (GTA) is an experimental apparatus designed to test mechanical components used in fuel handling systems of liquid-sodium cooled fast-spectrum nuclear reactors. The performance and lifetime of gears, bearings, and dynamic seals are the primary focus of study. Three experimental campaigns have been completed since the start of operation in 2019, and the GTA is currently assembled and ready to begin the fourth experimental campaign. Sodium operations at the Mechanisms Engineering Test Loop (METL) have been paused while repairs are made to the Building 308 Alkali Metal Scrubber. This work is nearly complete, and once METL is brought back into operation the GTA will begin sodium testing immediately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-1, AGR-2 and AGR-3/4 Dimensional Change Data Analysis

A series of Advanced Gas Reactor (AGR) experiments have been completed in the Advanced Test Reactor at Idaho National Laboratory in support of qualification and development of tristructural isotropic fuel. Each AGR test consists of multiple independently controlled and monitored capsules containing fuel compacts placed in a graphite cylinder. These capsules are instrumented with thermocouples embedded in the graphite, enabling temperature control. The fuel compacts are composed of fuel particles surrounded by a graphitic A3 matrix material. Dimensional change in AGR fuel compacts is vital because the swelling or shrinkage affects the size of the gas gaps that are used to control temperatures. Analysis of dimensional change in the AGR fuel compacts is needed to establish the variables directly relating to compact shrinkage. The variables initially identified for consideration were matrix density, compact density, fuel packing fraction, uranium loading, fuel particle diameter, cumulative fast neutron fluence, and volume average time average fuel temperature. In addition to the data available from the AGR experiments, the analysis included specimens formed from the same A3 matrix material used in Advanced Graphite Creep (AGC) experiments, which provide graphite creep data during irradiation for design and licensing purposes. The primary purpose of including the AGC specimens was to encompass dimensional behavior at zero packing fraction, zero uranium loading, and zero particle diameter. All possible combinations of first-order variable regressions were considered in the analysis. The study focused on identifying the best regression models for percent change in diameter, length, and volume. Bootstrap analysis was used to ensure the resulting regression models were robust and well-performing. The variables identified as very significant in predicting change in one or more dimensions (diameter, length, and volume) are volume average time average temperature, fast fluence, compact density, packing fraction and fuel particle diameter. Due to the presence of confounding effects between several variables, interpretation of these results is equivocal; the use of multiple statistical tests provides additional confidence in the conclusion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Performance Assessment of a Generic Nuclear Waste Repository in Shale - 18392

A performance assessment (PA) is an important component of a comprehensive safety analysis for a nuclear waste repository. In a PA, probabilistic simulations of the total repository system are performed, and results are evaluated against performance metrics. Uncertainty and sensitivity analyses help prioritize additional research and model development. The United States Department of Energy (DOE) has been developing a state of the art PA simulation software tool-kit, Geologic Disposal Safety Assessment (GDSA) Framework, that couples increasingly higher fidelity models of subsystem processes into total system PA simulations. Over the past several years, PAs of generic repositories in three geologic media (salt, shale, and crystalline rock) have demonstrated ongoing developments in capability. The current PA of a nuclear waste repository in a generic shale formation showcases GDSA Framework, including capabilities in domain discretization (Cubit), multi-physics simulations (PFLOTRAN), uncertainty and sensitivity analysis (Dakota), and visualization (Paraview). The generic shale reference case considers the disposal of 22,000 metric tons heavy metal of commercial spent nuclear fuel (SNF) in a generic shale formation. PA simulations account for the thermal load and radionuclide inventory of the waste form, components of the engineered barrier system including waste package and buffer, and components of the natural barrier system including the host rock shale and underlying and overlying stratigraphic units. Two repository layouts are considered, one for emplacement of waste packages containing 12 pressurized water reactor (PWR) assemblies, and one for 4-PWR waste package emplacement. Model domains are half-symmetry and contain between 7 and 22 million grid cells. Grid refinement captures the detail of individual waste packages, emplacement drifts, access drifts, and shafts. Simulations are run in a high-performance computing (HPC) environment on 512 or 2048 processes. The governing equations describing coupled heat and fluid flow and reactive transport are solved with PFLOTRAN, an open-source, massively parallel multiphase flow and reactive transport code. Additional simulated processes include waste package degradation; waste form dissolution; radioactive decay and ingrowth in aqueous, solid, and adsorbed phases; and a simple biosphere based on a pumping well. Simulations are run to 106 y; dose and radionuclide concentrations are observed within aquifers at a point approximately 5 km downgradient of the repository. Dakota is used to sample likely ranges of input parameters including waste form and waste package degradation rates and properties of engineered and natural materials to quantify uncertainty in predicted concentrations and sensitivity to input parameters. Given the assumptions of the reference case, results of 12-PWR and 4-PWR simulations are very similar. Dose at the pumping well 5-km downgradient of the repository does not exceed 10-9 Sv/y. I-129 is the largest contributor to dose. The dose due to Cl-36, the next largest contributor, is orders of magnitude smaller. At the pumping well, the concentration of I-129 5-km downgradient does not exceed 10-14 mol/L. Rank correlation coefficients indicate that the maximum concentration of I-129 within the aquifer is sensitive to shale (repository host rock) porosity and aquifer permeability. These results affirm that HPC-capable codes can be used to simulate important multi-physics couplings directly in a total system performance assessment of a geologic repository, and can be used in prioritization of future research and model development. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Comparison between Flownex and Corona thermal-hydraulic models for a single HTR prismatic fuel assembly - 18544

Computational tools and methodologies that can perform thermal-hydraulic analyses to reasonably predict the temperature distribution for the whole core of HTRs are useful for operational and safety analyses. In this paper, Flownex (a system code based on a one-dimensional thermal-fluid network methodology) and CORONA (Core Reliable Optimization and thermo-fluid Network Analysis) thermal-hydraulic models and results for a vertically stacked single fuel assembly will be compared. In Flownex, a basic unit cell containing part of the graphite and the associated fuel elements and coolant channels was developed. CORONA uses a basic unit cell concept for generating computational grids using several types of basic unit cells to model the heat transfer through the hexagonal blocks and a 1-D formulation to model the flow through the coolant channels. In CORONA, computational grids are generated using a combination of pre-generated mesh cells. The coolant channels and fuel rods are modelled explicitly. Flownex in contrast, models fuel and coolant channels implicitly by defining representative coolant channels, fuel rods and coated particle layers associated with each unit cell. Flownex can therefore model temperatures at coated particle level and also through each graphite block. The computational mesh employed by Flownex is much coarser than the mesh employed by CORONA. In both models, the helium gap between the fuel compact and the graphite block is modelled as stagnant. Flownex results were found to be of the same order of magnitude as those obtained using CORONA. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Transport Modeling of As-Run ATR Cycles to Support U-10Mo Research Reactor Fuel Qualification Experiment

The Department of Energy’s (DOE) Office of Materials Management and Minimization has been tasked with converting the five remaining United States High Performance Research Reactors (U.S. HPRR) from highly enriched uranium to low-enriched uranium. The Nuclear Regulatory Commission (NRC) regulates Massachusetts Institute of Technology Reactor (MITR), Missouri University Research Reactor (MURR), and National Bureau of Standards Reactor (NBSR); and DOE regulates the High Flux Isotope Reactor and Advanced Test Reactor (ATR). To meet the high demands of these reactors, the U.S. HPRR program has chosen to use 90% uranium - 10% molybdenum (U-10Mo) monolithic fuel. This plate-type fuel will undergo multiple irradiation experiment campaigns in ATR, from mini-plates to full element tests, over a large range of operating conditions. This will provide data in support of the fuel qualification of each reactor. This summary focuses on the as-run neutronic analysis of the first series of mini-plate (MP-1) experiments, which have been irradiated in the ATR. MP-1 experiment’s main goal is to demonstrate the fabrication process and meet the fuel irradiation performance requirements with primary focus on the fuel plates associated with the three NRC reactors, with a small focus on the low power requirements of the ATR fuel. The MP-1 experiments are planned to be the basis of the monolithic U-10Mo fuel for qualification through the NRC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transport Modeling of As-Run ATR Cycles for U-10Mo Fuel Qualification Experiment

The Department of Energy’s (DOE) Office of Materials Management and Minimization has been tasked with converting the five remaining United States High Performance Research Reactors (U.S. HPRR) from highly enriched uranium to low-enriched uranium. The Nuclear Regulatory Commission (NRC) regulates Massachusetts Institute of Technology Reactor (MITR), Missouri University Research Reactor (MURR), and National Bureau of Standards Reactor (NBSR); and DOE regulates the High Flux Isotope Reactor and Advanced Test Reactor (ATR). To meet the high demands of these reactors, the U.S. HPRR program has chosen to use 90% uranium - 10% molybdenum (U-10Mo) monolithic fuel. This plate-type fuel will undergo multiple irradiation experiment campaigns in ATR, from mini-plates to full element tests, over a large range of operating conditions. This will provide data in support of the fuel qualification of each reactor. This summary focuses on the as-run neutronic analysis of the first series of mini-plate (MP-1) experiments, which have been irradiated in the ATR. MP-1 experiment’s main goal is to demonstrate the fabrication process and meet the fuel irradiation performance requirements with primary focus on the fuel plates associated with the three NRC reactors, with a small focus on the low power requirements of the ATR fuel. The MP-1 experiments are planned to be the basis of the monolithic U-10Mo fuel for qualification through the NRC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Further Development of an Execution Strategy Analysis (ESA) Capability and Tool for the Management of Spent Nuclear Fuel (SNF) - 17146

An Execution Strategy Analysis (ESA) capability and tool are being developed to evaluate alternative execution strategies for the potential future deployment of a consolidated Interim Storage Facility as part of an integrated waste management system. Application of the ESA approach not only leverages but also goes beyond traditional project analysis tools. The ESA tool allows for ongoing performance assessment of the evolving project execution plans that take into account significant assumptions, risks, and uncertainties throughout the project lifecycle. Development and application of the ESA capability and tool continued in 2016, primarily focusing on enhancing its flexibility to model a range of scenarios regarding how an integrated system for managing spent nuclear fuel and high-level radioactive waste could be deployed. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effects of molar expansion ratio of fuels on engine efficiency

Fuel properties have a strong impact on the efficiency of internal combustion engines. Contrary to other physical and thermochemical fuel properties, the molar expansion ratio is normally ignored. Molar expansion ratio is the ratio of number of moles of the products to the reactants. In this work, the impact of the fuel’s molar expansion ratio on engine efficiency is investigated. Findings are based on simulations of a spark ignition engine using different fuels (standard fuels and user-defined fuels) and different dilution ratios. Simulations without heat transfer and friction were performed first. The combustion then takes place at top dead center with a very short combustion duration to approach the ideal Otto cycle. The heat transfer and friction were then added step by step. From this analysis, it could be concluded that the heat loss and friction work decrease as molar expansion ratio increases. The gross indicated and brake thermal efficiencies thus increase. User-defined fuels with different molar expansion ratio, but the same physical and thermochemical properties were then employed. The simulated results showed that the brake thermal efficiency increases by around 1.15% with an increase in molar expansion ratio of 0.02 compared to a fuel with a molar expansion ratio of unity. Lastly, the simulation was also done with air and exhaust gas recirculation dilution.

42 ENGINEERING↗

Experiments to Measure the Inversion Point of the Isothermal Reactivity Coefficient in a Water-Moderated Pin-Fueled Critical Assembly at Sandia

A new set of critical experiments exploring the temperature-dependence of the reactivity in a critical assembly is described. In the experiments, the temperature of the critical assembly will be varied to determine the temperature that produces the highest reactivity in the assembly. This temperature is the inversion point of the isothermal reactivity coefficient of the assembly. An analysis of relevant configurations is presented. Existing measurements are described and an analysis of these experiments presented. The overall experimental approach is described as are the modifications to the critical assembly needed to perform the experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of Natural Gas Fuel Cell Plant Configurations (Rev. 1)

This report presents the results of an updated Pathway Study for natural gas fueled, fuel cell (NGFC) power systems with carbon capture and storage (CCS). The results quantify the performance and cost benefits for a series of projected gains made through the development of advances in the component technologies or improvements in plant operation and maintenance. The results represent the potential future benefits of NGFC technology development. They also provide DOE with a basis to select the most appropriate development path for NGFC, and to measure and prioritize the contribution of its R&D program to future power systems technology.

03 NATURAL GAS↗

Drop Analysis of the Advanced Test Reactor Fresh Fuel Shipping Container with Heavier Low-Enriched Uranium Fuel Contents

The Advanced Test Reactor Fresh Fuel Shipping Container (ATR FFSC) is a rectangular stainless steel container used for shipping radioactive material. The container is described in the ATR FFSC Safety Analysis Report (SAR). Per the ATR FFSC SAR, the ATR FFSC is designated a Type AF-96 packaging per the definition of 10 CFR §71.4, and was originally designed to transport high enriched uranium (HEU) reactor fuel elements for the Advanced Test Reactor (ATR), the Advanced Test Reactor Critical (ATRC) facility, the Massachusetts Institute of Technology Reactor (MITR), and the University of Missouri Research Reactor (MURR). The Department of Energy, National Nuclear Security Administration’s (NNSA), Office of Material Management and Minimization (M3) is working with the Idaho National Laboratory (INL) to develop and qualify new low enriched uranium (LEU) fuels and technologies for use in the ATR, ATRC, MITR, and MURR reactors. The LEU fuel elements will weigh significantly more than the current HEU designs and, combined with their associated Fuel Handling Enclosures for packaging, some configurations will exceed the 50 lbf used in the ATR FFSC qualifying drop tests. There are LEU versions of MITR, MURR, and ATR fuel elements. However, for this evaluation, drop analysis of the ATR FFSC with only the heavier ATR Low Enrichment (LOWE) fuel element is considered in this evaluation because the LOWE fuel element is the heaviest of the considered LEU fuel elements. The ATR HEU fuel element and the ATR LOWE fuel element are identical in every design aspect except for the fuel meat inside the 19 fuel plates. The LEU fuel meats are made using a U-10Mo high-density foil rather than uranium dispersed in aluminum in the HEU fuel elements. The high density of the uranium in the LEU fuel meat increases the LOWE fuel element weight to just under 44 lbf (versus the 22.1 lbf weight of the tested ATR HEU fuel element). ATR fuel elements are placed in a thin-gauge aluminum weldment called a "Fuel Handling Enclosure" during packaging. The Fuel Handling Enclosure is used to cover and protect the element during loading and unloading operations. The ATR Fuel Handling Enclosure weighs about 15 lbf per the drawings in the ATR FFSC SAR and the weight is accounted for in this evaluation. Transporting the heavier LEU fuel elements require evaluation of two issues. The first is the effect of the increased mass of the LEU fuel elements on the survivability of the ATR FFSC package following the requisite drop qualifications. The second is the effect of the increased mass of the fuel plates on the fuel element during the same drops. The ATR FFSC containing an ATR HEU fuel element in an ATR Fuel Handling Enclosure was physically dropped multiple times to qualify the container as a Type AF-96 package. The ATR FFSC SAR describes the drop tests performed with an actual ATR HEU fuel element weighing 22.1 lbf contained in a 14.3 lbf Fuel Handling Enclosure for a total payload of 36.4 lbf. Those drop tests showed that the ATR FFSC maintained containment of the ATR HEU fuel element and the fuel element was not significantly damaged. (Containment herein is not defined as a leak tight but is retention of the radioactive contents.) The purpose of the evaluation is to analytically show that, for a similar set of tests, the ATR FFSC maintains containment of the heavier ATR LOWE fuel element and to assess the damage to the fuel element during the drops. The approach was to create finite element analysis (FEA) models that produce the same results as the physical drops. Those models were then used as the benchmarks for the follow-on analyses using the heavier contents. FEA models of the drops of ATR FFSC using up to a 115 lbf fuel element were run and evaluated. Likewise, drops of a LOWE fuel element weighing 44 lbf in the ATR FFSC were run and evaluated. It is important to note that this report was done at the quality level necessary to be included in a nuclear facility safety basis. However, it is not the intent of this report to conclude the suitability of the ATR FFSC for transporting the heavier payloads. This report only describes the results of the FEA as related to the required drop scenarios. Incorporation of the FEA into the safety basis will be evaluated by the ATR FFSC design authority. The physical drop tests of the HEU fuel element and FEA drop analysis for the LOWE fuel element showed noteworthy damage to the fuel plates. An aluminum protective block was conceived to mitigate the damage. The concept requires the blocks to be placed in the fuel element between the end boxes and fuel plates. Additional FEA drop analyses were performed using the protective block. The addition of the blocks is primarily intended to mitigate the damage to the LOWE fuel element fuel plates. However, FEA drop analyses of the ATR HEU fuel element with the blocks were also performed and included for information.

42 ENGINEERING↗

High Temperature Materials Interim Data Qualification Report

ABSTRACT Projects for the very high temperature reactor (VHTR) Technology Development Office provide data in support of Nuclear Regulatory Commission licensing of the VHTR. Fuel and materials to be used in the reactor are tested and characterized to quantify performance in high temperature and high fluence environments. The VHTR program has established the NGNP Data Management and Analysis System (NDMAS) to ensure that VHTR data are qualified for use, stored in a readily accessible electronic form, and analyzed to extract useful results. This document focuses on the first NDMAS objective. It describes the High Temperature Materials characterization data stream, the processing of these data within NDMAS, and reports the interim FY2010 qualification status of the data. Data qualification activities within NDMAS for specific types of data are determined by the data qualification category assigned by the data generator. The High Temperature Materials data are being collected under NQA-1 guidelines, and will be qualified data. For NQA-1 qualified data, the qualification activities include: (1) capture testing, to confirm that the data stored within NDMAS are identical to the raw data supplied, (2) accuracy testing to confirm that the data are an accurate representation of the system or object being measured, and (3) documenting that the data were collected under an NQA-1 or equivalent Quality Assurance program. Currently, data from two test series within the High Temperature Materials data stream have been entered into the NDMAS vault: 1. Tensile Tests for Sm (i.e., Allowable Stress) Confirmatory Testing – 1,403,994 records have been inserted into the NDMAS database. Capture testing is in process. 2. Creep-Fatigue Testing to Support Determination of Creep-Fatigue Interaction Diagram – 918,854 records have been processed and inserted into the NDMAS database. Capture testing is in process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of Increased Peak Temperatures for Spent Fuel Cladding Performance during Dry Storage (Rev.1)

NUREG-2214, “Managing Aging Processes in Storage (MAPS) Report,” (2019) documents the technical basis for age-related degradation mechanisms on spent nuclear fuel assemblies during dry storage operations. The technical bases have been reviewed, and hoop cladding stress calculations were conducted using the Fuel Analysis under Steady-state and Transients (FAST) code at elevated normal condition temperatures of 425°C and 450°C, and at an off-normal and accident conditions temperature of 600°C. The NUREG-2214 conclusions are substantiated by the referenced literature. The calculations demonstrate that the aging mechanisms primarily driven by hoop stress such as hydride reorientation, delayed hydride cracking, thermal and athermal (low-temperature) creep, and localized mechanical overload are either not credible or do not compromise the fuel assembly’s performance for increased peak normal condition temperatures of 425°C or 450°C during the up to 60-year dry storage period. Other aging mechanisms considered are also not credible for compromising the fuel assembly’s performance during 60-year dry storage with a peak temperature of 400ºC as specified in ISG – 11 Rev. 3, and the same is indicated for the increased peak normal condition temperatures of 425°C or 450°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sugarcane Biomass Production in South Florida: A Comparative Emergy Assessment of Organic Soil and Mineral Soil Production Systems

An Emergy Assessment (EMA) of sugarcane cultivation as feedstock for bioethanol production in South Florida was performed to develop a sustainability profile of the farming systems. In this study, a sugarcane farming system on muck soil (organic soil) was compared with a similar crop- ping system on a sandy soil (mineral soil). Our study provides a comparison of these alternative systems from the perspective of their resource use, environmental impact and sustainability. The representative farm for both systems was based on a 5000 acres farm assumed to be already established in South Florida. Emergy analysis was applied to evaluate environmental support required for the sugarcane production in both systems. In line with the methodology a quantitative inventory of free natural resources and purchased input flows into the systems was created. These results showed that aside ground water irrigation which dominates (44%) in both systems, the largest emergy flows for biofuel production on organic soil were associated with soil erosion or subsidence (19%), labor (12%), evapotranspiration (11%), and fuel (8%). However, for sandy soil production, the main contributors were lime (13%), labor (12%), and fuel (8%). Furthermore, the emergy analysis suggests that due to the non-renewability of soil loss in the organic soil farming system, a reduction in the purchased inputs for sandy (mineral) soils based on alternative farming measures potentially makes mineral soil sugarcane ethanol production a rather more sustainable and attractive alternative for a better environmental performance.

09 BIOMASS FUELS↗

A Novel Non-Platinum Group Electrocatalyst for PEM Fuel Cell Application

Precious-metal catalysts (predominantly Pt or Pt-based alloys supported on carbon) have traditionally been used to catalyze the electrode reactions in polymer electrolyte membrane (PEM) fuel cells. However as PEM fuel systems begin to approach commercial reality, there is an impending need to replace Pt with a lower cost alternative. The present study investigates the performance of a carbon-supported tantalum oxide material as a potential oxygen reduction reaction (ORR) catalyst for use on the cathode side of the PEM fuel cell membrane electrode assembly. Although bulk tantalum oxide tends to exhibit poor electrochemical performance due to limited electrical conductivity, it displays a high oxygen reduction potential; one that is comparable to Pt. Analysis of the Pourbaix electrochemical equilibrium database also indicates that tantalum oxide (Ta2O5) is chemically stable under the pH and applied potential conditions to which the cathode catalyst is typically exposed during stack operation. Nanoscale tantalum oxide catalysts were fabricated using two approaches, by reactive oxidation sputtering and by direct chemical synthesis, each carried out on a carbon support material. Nanoscale tantalum oxide particles measuring approximately 6nm in size that were sputtered onto carbon paper exhibited a mass-specific current density as high as one-third that of Pt when measured at 0.6V vs. NHE. However because of the two-dimensional nature of this particle-on-paper structure, which limits the overall length of the triple phase boundary junctions where the oxide, carbon paper, and aqueous electrolyte meet, the corresponding area-specific current density was quite low. The second synthesis approach yielded a more extended, three-dimensional structure via chemical deposition of nanoscale tantalum oxide particles on carbon powder. These catalysts exhibited a high ORR onset potential, comparable to that of Pt, and displayed a significant improvement in the area-specific current density. Overall, the highest mass-specific current density of the carbon-powder supported catalyst was ~ 9% of that of Pt.

30 DIRECT ENERGY CONVERSION↗

Quality Guide Energy System Studies: Introduction to Performing a Techno-Economic Analysis for Power Generation Plants

The QGESS: Performing a Techno-Economic Analysis for Power Generation Plants provides guidelines on performing a techno-economic analysis (TEA) of power generation processes. The report includes guidance on preparing a technology analysis plan (TAP), a design basis, performing the technical analysis, performing the economic analysis, and information that should be reported. This guideline references numerous reports that provide examples of TEAs and provides a short description of most of the QGESS reports listed on this web page that provide useful information for specific aspects of performing a TEA.

20 FOSSIL-FUELED POWER PLANTS↗