SEARCH · Search NASA

Results for “Function Estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Evaluation of the ride quality of a light twin engine airplane using a ride quality meter

A ride quality meter was used to establish the baseline ride quality of a light twin-engine airplane planned for use as a test bed for an experimental gust alleviation system. The ride quality meter provides estimates of passenger ride discomfort as a function of cabin noise and vibration (acceleration) in five axes (yaw axis omitted). According to the ride quality meter, in smooth air the cabin noise was the dominant source of passenger discomfort, but the total discomfort was approximately the same as that for the smooth-air condition. The researcher's subjective opinion, however, is that the total ride discomfort was much worse in the moderate turbulence than it was in the smooth air. The discrepancy is explained by the lack of measurement of the low-frequency accelerations by the ride quality meter.

Stewart, Eric C.↗

NASA NTRS1989

Flutter Clearance of the F-18 High-angle-of-attack Research Vehicle with Experimental Wingtip Instrumentation Pods

An F-18 aircraft was modified with wingtip instrumentation pods for use in NASA's high-angle-of-attack research program. Ground vibration and flight flutter testing were performed to clear an acceptable flight envelope for the aircraft. Flight test utilized atmospheric turbulence for structural excitation; the aircraft displayed no adverse aeroelastic trends within the envelope tested. The data presented in this report include mode shapes from the ground vibration and estimates of frequency and damping as a function of Mach number.

Freudinger, Lawrence C.↗

NASA NTRS1989

The dissociation energy of He2(+)

Ab initio potential energy curves for He2(+) are computed using full CI wavefunctions in conjuction with large Gaussian and Slater basis sets. The computed curves yield rotational-vibrational transitions with errors of less than 1/cm. They also yield quasi-bound levels with energies and lifetimes in reasonable agreement with translational spectroscopy measurements. The best D(e) is estimated to be 2.470 eV. Green's function Monte Carlo calculations yield a very similar value, 2.466 + or - 0.005.

Bauschlicher, Charles W., Jr.↗

NASA NTRS1991

Fundamental studies of rotor wakes in low speed forward flight using wide-field shadowgraphy

Experiments were conducted using the wide-field shadowgraph method to visualize the wake geometry from a helicopter rotor in low speed forward flight. The experiments were performed with an isolated rotor and with a body representing a helicopter fuselage. Particular attention was paid to documenting the isolated rotor wake geometry, blade vortex interaction phenomena near the rotor plane, the distortion made to the wake due to the presence of the body, and detailing the interaction of the tip vortices with the body surface. Quantitative measurements were made of the wake trajectories as functions of wake age, as well as estimates of the tip vortex core radius. The results have provided many details of the rotor wake structure that are useful for validating rotor wake and rotor/body interactional models in forward flight. The use of the wide-field shadowgraph method offers an important tool for visualizing rotor wake vortices, and helping to understand the complex three-dimensional nature of rotor wakes in forward flight.

Leishman, J. G.↗

NASA NTRS1991

A nonparametric software-reliability growth model

The authors (1985) previously introduced a nonparametric model for software-reliability growth which is based on complete monotonicity of the failure rate. The authors extend the completely monotone software model by developing a method for providing long-range predictions of reliability growth, based on the model. They derive upper and lower bounds on extrapolation of the failure rate and the mean function. These are then used to obtain estimates for the future software failure rate and the mean future number of failures. Preliminary evaluation indicates that the method is competitive with parametric approaches, while being more robust.

Sofer, Ariela↗

NASA NTRS1992

User's manual for the Gaussian windows program

'Gaussian Windows' is a method for exploring a set of multivariate data, in order to estimate the shape of the underlying density function. The method can be used to find and describe structural features in the data. The method is described in two earlier papers. I assume that the reader has access to both of these papers, so I will not repeat material from them. The program described herein is written in BASIC and it runs on an IBM PC or PS/2 with the DOS 3.3 operating system. Although the program is slow and has limited memory space, it is adequate for experimenting with the method. Since it is written in BASIC, it is relatively easy to modify. The program and some related files are available on a 3-inch diskette. A listing of the program is also available. This user's manual explains the use of the program. First, it gives a brief tutorial, illustrating some of the program's features with a set of artificial data. Then, it describes the results displayed after the program does a Gaussian window, and it explains each of the items on the various menus.

Jaeckel, Louis A.↗

NASA NTRS1992

Correcting x ray spectra obtained from the AXAF VETA-I mirror calibration for pileup, continuum, background and deadtime

The VETA-I mirror was calibrated with the use of a collimated soft X-ray source produced by electron bombardment of various anode materials. The FWHM, effective area and encircled energy were measured with the use of proportional counters that were scanned with a set of circular apertures. The pulsers from the proportional counters were sent through a multichannel analyzer that produced a pulse height spectrum. In order to characterize the properties of the mirror at different discrete photon energies one desires to extract from the pulse height distribution only those photons that originated from the characteristic line emission of the X-ray target source. We have developed a code that fits a modeled spectrum to the observed X-ray data, extracts the counts that originated from the line emission, and estimates the error in these counts. The function that is fitted to the X-ray spectra includes a Prescott function for the resolution of the detector a second Prescott function for a pileup peak and a X-ray continuum function. The continuum component is determined by calculating the absorption of the target Bremsstrahlung through various filters correcting for the reflectivity of the mirror and convolving with the detector response.

Chartas, G.↗

NASA NTRS1993

Ellipsometric study of ambient-produced overlayer growth rate on YBa2Cu3O(7-x) films

An ellipsometric study of ambient-reaction-produced BaCO3 overlayer growth on laser-ablated YBCO is presented as a function of time. The effects of the anisotropy of YBCO on the ellipsometric data inversion process are discussed, and it is concluded that with certain restrictions on the data acquisition method, the anisotropic substrate can be adequately modeled by its isotropic pseudodielectric function for the purpose of overlayer thickness estimation. It is found that after an initial period of rapid growth attributed to the chemical reaction of the exposed surface bonds, the BaCO3 overlayer growth is linear at 1-2 A per day. This slow growth rate is attributed to the complexity of the BaCO3-forming reaction, together with the need for ambient reactants to diffuse through the overlayer.

Sieg, Robert M.↗

NASA NTRS1993

Correcting X-ray spectra obtained from the AXAF VETA-I mirror calibration for pileup, continuum, background and deadtime

The VETA-I mirror was calibrated with the use of a collimated soft X-ray source produced by electron bombardment of various anode materials. The FWHM, effective area and encircled energy were measured with the use of proportional counters that were scanned with a set of circular apertures. The pulsers from the proportional counters were sent through a multichannel analyzer that produced a pulse height spectrum. In order to characterize the properties of the mirror at different discrete photon energies one desires to extract from the pulse height distribution only those photons that originated from the characteristic line emission of the X-ray target source. We have developed a code that fits a modeled spectrum to the observed X-ray data, extracts the counts that originated from the line emission, and estimates the error in these counts. The function that is fitted to the X-ray spectra includes a Prescott function for the resolution of the detector a second Prescott function for a pileup peak and a X-ray continuum function. The continuum component is determined by calculating the absorption of the target Bremsstrahlung through various filters, correcting for the reflectivity of the mirror and convolving with the detector response.

Chartas, G.↗

NASA NTRS1994

Adaptive model reduction for continuous systems via recursive rational interpolation

A method for adaptive identification of reduced-order models for continuous stable SISO and MIMO plants is presented. The method recursively finds a model whose transfer function (matrix) matches that of the plant on a set of frequencies chosen by the designer. The algorithm utilizes the Moving Discrete Fourier Transform (MDFT) to continuously monitor the frequency-domain profile of the system input and output signals. The MDFT is an efficient method of monitoring discrete points in the frequency domain of an evolving function of time. The model parameters are estimated from MDFT data using standard recursive parameter estimation techniques. The algorithm has been shown in simulations to be quite robust to additive noise in the inputs and outputs. A significant advantage of the method is that it enables a type of on-line model validation. This is accomplished by simultaneously identifying a number of models and comparing each with the plant in the frequency domain. Simulations of the method applied to an 8th-order SISO plant and a 10-state 2-input 2-output plant are presented. An example of on-line model validation applied to the SISO plant is also presented.

Lilly, John H.↗

NASA NTRS1994

Directional radiance measurements: Challenges in the sampling of landscapes

Most earth surfaces, particularly those supporting natural vegetation ecosystems, constitute structurally and spectrally complex surfaces that are distinctly non-Lambertian reflectors. Obtaining meaningful measurements of the directional radiances of landscapes and obtaining estimates of the complete bidirectional reflectance distribution functions of ground targets with complex and variable landscape and radiometric features are challenging tasks. Reasons for the increased interest in directional radiance measurements are presented, and the issues that must be addressed when trying to acquire directional radiances for vegetated land surfaces from different types of remote sensing platforms are discussed. Priority research emphases are suggested, concerning field measurements of directional surface radiances and reflectances for future research. Primarily, emphasis must be given to the acquisition of more complete and directly associated radiometric and biometric parameter data sets that will empower the exploitation of the 'angular dimension' in remote sensing of vegetation through enabling the further development and rigorous validation of state of the art plant canopy models.

Deering, D. W.↗

NASA NTRS1994

Properties of a B0 I stellar wind and interstellar grains derived from Ginga observations of the binary X-ray pulsar 4U 1538-52

From measurements of the X-ray eclipse phenomena of the binary X-ray pulsar 4U 1538-52, we derive properties of the stellar wind of its B0 I companion, QV Nor, and a constraint on models of interstellar grains. Estimates of the wind density as a function of the distance from the center of QV Nor are obtained from an analysis of the variation of X-ray attenuation during an eclipse egress. A Monte Carlo computation of the absorption and scattering of X-rays in the X-ray-ionized wind accounts for approximately two-thirds of the spectrum of X-rays with energies above 4.5 keV observed during the eclipse. Our upper limit on R(sub XV) is 0.06/mag, which implies that the X-ray scattering efficiency of interstellar dust is less than expected for solid grains with a size distribution of the form n(sub g)(a) approximately a(exp -3.5) in the range from 0.005 to 0.25 microns and composed of silicate (R(sub XV) = 0.22/mag) or a silicate-graphite mixture (R(sub XV) = 0.11/mag) as derived from the calculations of Martin & Rouleau (1991). This lends support to the idea (Mathis & Whiffen 1989) that interstellar grains are 'fluffy' aggregates with an average bulk density less than that of their constitutent particles. Such aggregates would have a smaller ratio of X-ray scattering efficiency to optical extinction efficiency compared with solid grains of the same material.

Clark, George W.↗

NASA NTRS1995

A comparison of two algorithms for simulating collisionless systems

Two completely different simulation algorithms are compared by applying them to the same stellar dynamical problems: one is a self-consistent field (SCF) method for solving Poisson's equation and the other is a phase-space method for integrating the collisionless Boltzmann equation. We consider simulations of spherical stellar systems which are initially far from equilibrium and relax to their final states by gravitational collapse. The initial conditions consist of either uniform-density spheres or nonequilibrium models having Plummer density profiles, in which velocity dispersions are assigned according to given virial ratios. If a few tens of radial expansion terms with hundreds of thousands of particles are used in the SCF code, excellent agreement is found between the results it generates and those obtained with the phase-space solver, provided that a sufficiently large number of grid cells are employed with the latter. These findings imply that for simulating collisionless systmes over many dynamical times, the SCF approach based on sampling phase space is competitive with the approach treating phase space as a continuous fluid. The results of our tests make it possible to estimate the number of particles and basis functions required in situations like those modeled. Limitations of the SCF method and the choice of an optimal set of basis functions are also discussed.

Hozumi, Shunsuke↗

NASA NTRS1997

AIAA Survivability Technical Committee Draft

A relatively new area of interest in aerospace systems survivability is the growing threat of spacecraft penetration by orbital debris. Orbital debris, or "space junk", is composed of the man-made remnants of non-functioning spacecraft still orbiting the Earth. NASA estimates that there are currently over 100,000 orbital debris particles 1 centimeter in diameter or larger that cannot be tracked by existing radar, with the population growing at approximately 4% per year in low earth orbits. With an average velocity of over 8.7 km/sec, these projectiles can penetrate and disable many vulnerable spacecraft systems. Since the likelihood of spacecraft penetration increases with spacecraft surface area, large spacecraft (such as the International Space Station) and communication satellite fleets (such as Iridium) have begun to adopt survivability enhancement strategies similar to those employed by combat aircraft. Collision avoidance maneuvers are commonly practiced by the Space Shuttle and are planned by the International Space Station to decrease their susceptibility to impact by trackable orbital debris; likewise, improved shielding, internal equipment placement, and improved crew operations following penetration can reduce the vulnerability of spacecraft to loss following orbital debris impact. Computer simulations such as the Manned Spacecraft and Crew Survivability (MSCSurv) program at the NASA-Marshall Space Flight Center have recently been developed to quantify and reduce the likelihood of crew or spacecraft loss following orbital debris penetration. The AIAA Survivability Technical Committee is working to enable the transfer of military-developed survivability technologies to help the aerospace industry cope with this growing threat.

Shipman, Jim↗

NASA NTRS1999

Forward Modeling of Carbonate Proxy Data from Planktonic Foraminifera using Oxygen Isotope Tracers in a Global Ocean Model

The distribution and variation of oxygen isotopes in seawater are calculated using the Goddard Institute for Space Studies global ocean model. Simple ecological models are used to estimate the planktonic foraminiferal abundance as a function of depth, column temperature, season, light intensity, and density stratification. These models are combined to forward model isotopic signals recorded in calcareous ocean sediment. The sensitivity of the results to the changes in foraminiferal ecology, secondary calcification, and dissolution are also examined. Simulated present-day isotopic values for ecology relevant for multiple species compare well with core-top data. Hindcasts of sea surface temperature and salinity are made from time series of the modeled carbonate isotope values as the model climate changes. Paleoclimatic inferences from these carbonate isotope records are strongly affected by erroneous assumptions concerning the covariations of temperature, salinity, and delta (sup 18)O(sub w). Habitat-imposed biases are less important, although errors due to temperature-dependent abundances can be significant.

Schmidt, Gavin A.↗

NASA NTRS1999

Multidisciplinary Optimization Branch Experience Using iSIGHT Software

The Multidisciplinary Optimization (MDO) Branch at NASA Langley is investigating frameworks for supporting multidisciplinary analysis and optimization research. A framework provides software and system services to integrate computational tasks and allows the researcher to concentrate more on the application and less on the programming details. A framework also provides a common working environment and a full range of optimization tools, and so increases the productivity of multidisciplinary research teams. Finally, a framework enables staff members to develop applications for use by disciplinary experts in other organizations. This year, the MDO Branch has gained experience with the iSIGHT framework. This paper describes experiences with four aerospace applications, including: (1) reusable launch vehicle sizing, (2) aerospike nozzle design, (3) low-noise rotorcraft trajectories, and (4) acoustic liner design. Brief overviews of each problem are provided, including the number and type of disciplinary codes and computation time estimates. In addition, the optimization methods, objective functions, design variables, and constraints are described for each problem. For each case, discussions on the advantages and disadvantages of using the iSIGHT framework are provided as well as notes on the ease of use of various advanced features and suggestions for areas of improvement.

Padula, S. L.↗

NASA NTRS2001

Airborne Sun photometry and Closure Studies in SAFARI-2000 Dry Season Campaign

From August 13 to September 25, the Southern African Regional Science Initiative's (SAFARI 2000) dry-season airborne campaign studied the complex interactions between the region's ecosystems, air pollution, atmospheric circulation, land-atmosphere interactions, and land use change. The field campaign was timed to coincide with the annual winter fire season in Southern Africa. This challenging campaign. which coordinated ground-based measurement teams, multiple research aircraft, and satellite overpasses across nine African nations, was head quartered at the Petersburg International Airport in South Africa's Northern Province. Among many others, unique coordinated observations were made of the evolution of massive, thick haze layers produced by industrial emissions, biomass burning, marine and biogenic sources. The NASA Ames Airborne Tracking 14-channel Sunphotometer (AATS-14) was operated successfully aboard the University of Washington CV-580 during 24 data flights. The AATS-14 instrument measures the transmission of the direct solar beam at 14 discrete wavelengths (3501558 nm) from which we derive spectral aerosol optical depths (AOD), columnar water vapor (CWV) and columnar ozone. Flying at different altitudes over a fixed location allows derivation of layer AOD and CWV. Data taken during feasible vertical profiles allows derivation of aerosol extinction and water vapor density. In the talk, we show comparisons with ground-based AERONET sun/sky photometer results, with ground based MPL-Net lidar data, and with measurements from a lidar aboard the high flying ER-2 aircraft. We will use measurements from the Ames Solar Spectral Flux Radiometer to derive estimates of solar spectral forcing as a function of aerosol thickness. Validations of TOMS and Terra satellite aerosol and water-vapor retrievals will also be discussed.

Schmid, B.↗

NASA NTRS2002

Cloud Algorithm Design and Performance for the 2002 Geoscience Laser Altimeter System Mission

A satellite borne lidar instrument, the Geoscience Laser Altimeter System (GLAS), is to be launched in late 2002 and will provide continuous profiling of atmospheric clouds and aerosol on a global basis. Data processing algorithms have been developed to provide operational data products in near real time. Basic data products for cloud observations are the height of the top and bottom of single to multiple cloud layers and the lidar calibrated observed backscatter cross section up to the level of signal attenuation. In addition the optical depth and vertical profile of visible extinction cross section of many transmissive cloud layers and most haze layers are to be derived. The optical thickness is derivable in some cases from the attenuation of the molecular scattering below cloud base. In other cases an assumption of the scattering phase function is required. In both cases a estimated correction for multiple scattering is required. The data processing algorithms have been tested in part from aircraft measurements used to simulated satellite data. The GLAS lidar observations will be made from an orbit that will allow inter comparison with all other existing satellite cloud measurements.

Spinhirne, J. D.↗