Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES, FLAT - STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Flutter analysis of low aspect ratio wings

Several very low aspect ratio flat plate wing configurations are analyzed for their aerodynamic instability (flutter) characteristics. All of the wings investigated are delta planforms with clipped tips, made of aluminum alloy plate and cantilevered from the supporting vehicle body. Results of both subsonic and supersonic NASTRAN aeroelastic analyses as well as those from another version of the program implementing the supersonic linearized aerodynamic theory are presented. Results are selectively compared with the experimental data; however, supersonic predictions of the Mach Box method in NASTRAN are found to be erratic and erroneous, requiring the use of a separate program.

Parnell, L. A.↗

On similarity solutions of a boundary layer problem with an upstream moving wall

The problem of a boundary layer on a flat plate which has a constant velocity opposite in direction to that of the uniform mainstream is examined. It was previously shown that the solution of this boundary value problem is crucially dependent on the parameter which is the ratio of the velocity of the plate to the velocity of the free stream. In particular, it was proved that a solution exists only if this parameter does not exceed a certain critical value, and numerical evidence was adduced to show that this solution is nonunique. Using Crocco formulation the present work proves this nonuniqueness. Also considered are the analyticity of solutions and the derivation of upper bounds on the critical value of wall velocity parameter.

Hussaini, M. Y.↗

Vortex flow hysteresis

An experimental study was conducted to quantify the hysteresis associated with various vortex flow transition points and to determine the effect of planform geometry. The transition points observed consisted of the appearance (or disappearance) of trailing edge vortex burst and the transition to (or from) flat plate or totally separated flows. Flow visualization with smoke injected into the vortices was used to identify the transitions on a series of semi-span models tested in a low speed tunnel. The planforms tested included simple deltas (55 deg to 80 deg sweep), cranked wings with varying tip panel sweep and dihedral, and a straked wing. High speed movies at 1000 frames per second were made of the vortex flow visualization in order to better understand the dynamics of vortex flow, burst and transition.

Cunningham, A. M., Jr.↗

Performance tests for the NASA Ames Research Center 20 cm x 40 cm oscillating flow wind tunnel

An evaluation is presented of initial tests conducted to assess the performance of the NASA Ames 20 cm x 40 cm oscillating flow wind tunnel. The features of the tunnel are described and two aspects of tunnel operation are discussed. The first is an assessment of the steady mainstream and boundary layer flows and the second deals with oscillating mainstream and boundary layer flows. Experimental results indicate that in steady flow the test section mainstream velocity is uniform in the flow direction and in cross section. The freestream turbulence intensity is about 0.2 percent. With minor exceptions the steady turbulent boundary layer generated on the top wall of the test section exhibits the characteristics of a zero pressure gradient turbulent boundary layer generated on a flat plate. The tunnel was designed to generate sinusoidal oscillating mainstream flows. Experiments confirm that the tunnel produces sinusoidal mainstream velocity variations for the range of frequencies (up to 15 Hz). The results of this study demonstrate that the tunnel essentially produces the flows that it was designed to produce.

Cook, W. J.↗

The influence of defects of the fatigue resistance of butt and girth welds in A106B steel

This three-phase study was directed at developing a fitness for service defect acceptance criteria for welds with defect indications. The study focussed on A106 Gr. B steel pipe. The first phase involved a literature search and critical review to develop the preliminary acceptance criteria to the extent permitted by the data. The second phase developed data for flat plate, wall segment, and vessel specimens containing artificial or natural planar or volumetric defects. The final phase developed acceptance criteria from the test data.

Leis, B. N.↗

Feasibility study of optical boundary layer transition detection method

A high sensitivity differential interferometer was developed to locate the region where the boundary layer flow undergoes transition from laminar to turbulent. Two laboratory experimental configurations were used to evaluate the performance of the interferometer: open shear layer, and low speed wind tunnel turbulent spot configuration. In each experiment, small temperature fluctuations were introduced as the signal source. Simultaneous cold wire measurements were compared with the interferometer data. The comparison shows that the interferometer is sensitive to very weak phase variations in the order of 0.001 the laser wavelength. An attempt to detect boundary layer transition over a flat plate at NASA-Langley Unitary Supersonic Wind Tunnel using the interferometer system was performed. The phase variations during boundary layer transition in the supersonic wind tunnel were beyond the minimum signal-to-noise level of the instrument.

Azzazy, M.↗

Numerical simulation of boundary layers. Part 1: Weak formulation and numerical method

A numerical method designed to solve the time-dependent, three-dimensional, incompressible Navier-Stokes equations in boundary layers is presented. The fluid domain is the half-space over a flat plate, and periodic conditions are applied in the horizontal directions. The discretization is spectral. The basis functions are divergence-free and a weak formulation of the momentum equation is used, which eliminates the pressure term. An exponential mapping and Jacobi polynomials are used in the semi-infinite direction, with the irrotational component receiving special treatment. Issues related to the accuracy, stability and efficiency of the method are discussed. Very fast convergence is demonstrated on some model problems with smooth solutions. The method has also been shown to accurately resolve the fine scales of transitional and turbulent boundary layers.

Spalart, P. R.↗

Critical evaluation of the unsteady aerodynamics approach to dynamic stability at high angles of attack

Bifurcation theory is used to analyze the nonlinear dynamic stability characteristics of an aircraft subject to single-degree-of-freedom. The requisite moment of the aerodynamic forces in the equations of motion is shown to be representable in a form equivalent to the response to finite amplitude oscillations. It is shown how this information can be deduced from the case of infinitesimal-amplitude oscillations. The bifurcation theory analysis reveals that when the bifurcation parameter is increased beyond a critical value at which the aerodynamic damping vanishes, new solutions representing finite amplitude periodic motions bifurcate from the previously stable steady motion. The sign of a simple criterion, cast in terms of aerodynamic properties, determines whether the bifurcating solutions are stable or unstable. For the pitching motion of flat-plate airfoils flying at supersonic/hypersonic speed and for oscillation of flaps at transonic speed, the bifurcation is subcritical, implying either the exchanges of stability between steady and periodic motion are accompanied by hysteresis phenomena, or that potentially large aperiodic departures from steady motion may develop.

Hui, W. H.↗

Structural Characterization and Gas Reactions of Small Metal Particles by High Resolution In-situ TEM and TED

A commercial electron microscope with flat-plate upper pole piece configuration of the objective lens and top entry specimen introduction was modified to obtain 5 x 10 to the minus 10th power mbar pressure at the site of the specimen while maintaining the convenience of a specimen airlock system that allows operation in the 10 to the 10th power mbar range within 15 minutes after specimen change. The specimen chamber contains three wire evaporation sources, a specimen heater, and facilities for oxygen or hydrogen plasma treatment to clean as-introduced specimens. Evacuation is achieved by dural differential pumping, with fine entrance and exit apertures for the electron beam. With the microscope operating at .000001 mbar, the first differential pumping stage features a high-speed cryopump operating in a stainless steel chamber that can be mildly baked and reaches 1 x 10 to the minus 8th power mbar. The second stage, containing the evaporation sources and a custom ionization gauge within 10 cm from the specimen, is a rigorously uncompromised all-metal uhv-system that is bakable to above 200 C throughout and is pumped with an 80-liter ion pump. Design operating pressures and image quality (resolution of metal particles smaller than 1 nm in size) was achieved.

Heinemann, K.↗

Turbulent Reynolds analogy factors for nonplanar surface microgeometries

Direct measurements of turbulent Reynolds analogy factors are presented for 15 nonplanar surface microgeometries (including riblets, oscillating transverse curvature, wavy walls, and micro air bearings) for momentum thickness Reynolds numbers of 1638-2631. It is shown that certain types of nonplanar surface microgeometries will increase turbulent Reynolds analogy factors significantly above flat-plate levels. In several cases, the observed elevated heat-transfer efficiencies represent the combined effects of both heat-transfer increases and drag decreases. Generally, the results suggest that decreases of the order of 20 percent are possible in heat exchanger volume, cost, and weight for designs with extensive planar surfaces.

Lindemann, A. M.↗

High-temperature thermocouple and heat flux gauge using a unique thin film-hardware hot junction

A special thin film-hardware material thermocouple (TC) and heat flux gauge concept for a reasonably high temperature and high flux flat plate heat transfer experiment was fabricated and tested to gauge temperatures of 911 K. This concept was developed for minimal disturbance of boundary layer temperature and flow over the plates and minimal disturbance of heat flux through the plates. Comparison of special heat flux gauge Stanton number output at steady-state conditions with benchmark literature data was good and agreement was within a calculated uncertainty of the measurement system. Also, good agreement of special TC and standard TC outputs was obtained and the results are encouraging. Oxidation of thin film thermoelements was a primary failure mode after about 5 of operation.

Liebert, C. H.↗

Development of an explicit multigrid algorithm for quasi-three-dimensional viscous flows in turbomachinery

A rapid quasi three-dimensional analysis was developed for blade-to-blade flows in turbomachinery. The analysis solves the unsteady Euler or thin layer Navier-Stokes equations in a body-fitted coordinate system. It accounts for the effects of rotation, radius change, and stream-surface thickness. The Baldwin-Lomax eddy-viscosity model is used for turbulent flows. The equations which are solved b a two-stage Runge-Kutta scheme made efficient by use of vectorization, a variable time-step, and a flux-based multigrid scheme, are described. A stability analysis is presented for the two-stage. Results for a flat-plate model problem show the applicability of the method to axial, radial, and rotating geometries. Results for a centrifugal impeller and a radial diffuser show that the quasi three-dimensional viscous analysis can be a practical design tool.

Chima, R. V.↗

Compressible laminar boundary layer with real gas effects for flight conditions to M(e) = 8 and T(o) = 2500 K

One of the problems for the hypersonic flights is the lack of accurate methods for predicting the boundary layer parameters at high Mach numbers and temperatures. At high Mach numbers and temperatures, the real gas effects should be included in calculations of the compressible laminar and turbulent boundary layers. By introducing the Mangler-Levy-Lees transformation, the compressible laminar boundary layer equations were transformed into two ordinary differential equations. To solve these ordinary differential equations for the flow over a flat plate, the Runge-Kutta method of order 5 and 6 was used with a secant method of solving the simultaneous nonlinear equations for the boundary layer conditions. Instead of using the perfect gas assumptions, the properties of air in the temperature range of 100 to 2500 K at M(e) = 8 were used for the calculations. The calculations were carried out for free flight conditions. The real gas effects were significant for the conditions of high freestream Mach numbers, and the boundary layer parameters from the real gas solutions were quite different from the existing formulas and solutions.

Nagamatsu, H. T.↗

The flowfield structure of the 3-D shock wave - Boundary layer interaction generated by a 20 deg sharp fin at Mach 3

The three-dimensional oblique shock wave-turbulent boundary layer interaction generated by a sharp fin attached to a flat plate is investigated experimentally and theoretically for Mach 3 and Reynolds number 9 x 10 to the 5th using two different models. Both models employ the three-dimensional compressible Navier-Stokes equations in mass-averaged variables; one model utilizes the algebraic turbulent eddy viscosity model of Baldwin and Lomax (1978), while the other model employs the two-equation turbulence model of Jones and Launder (1972) coupled with the wall function model of Viegas and Rubesin (1985). The computed surface pressure, surface streamlines, pitot pressure, and yaw angle profiles are found to be in good agreement with experimental data. The three-dimensional velocity fields computed by both models are in close agreement, although the eddy viscosity profiles differ significantly within the three-dimensional interaction. This result indicates that the overall structure of this three-dimensional sharp fin interaction is insensitive to the turbulence model.

Knight, D. D.↗

A numerical study of three-dimensional incompressible flow around multiple posts

The incompressible laminar flow around single and double rows of an infinite number of posts between two flat plates has been calculated numerically. A C-grid with periodic boundary conditions has been used. The angle of attack, measured from the line normal to the row of posts, was varied between zero and less than 90 deg. The pressure loading was computed for all of the posts in each of these cases. Most of these calculations have been carried out on the Numerical Aerodynamic Simulation Cray 2 at NASA Ames Research Center.

Rogers, S. E.↗

Comparison of computations and experimental data for leading edge vortices - Effects of yaw and vortex flaps

Computations are presented using the conical Euler equations for swept delta wings with leading edge vortices. All the wings have sharp leading edges swept at 75 degrees to the freestream. In addition to an idealized flat plate model, geometrical features also included are thickness, centerbody, and two vortex flaps. Freestream Mach numbers of 1.7 to 2.8, angles of attack of 10 and 12 degrees, and angles of yaw of 0 and 8 degrees are considered. The computations are compared with pitot pressure traverses for one case. Other calculations are compared with pitot pressure traverses for one case. Other calculations are compared with surface pressure data and vapor screen pictures recently obtained at NASA Langley Research Center. The comparisons indicate that the dominant features of these flows are adequately modeled by the Euler equations, but viscous models are needed for the surface boundary layer and secondary separations.

Murman, E. M.↗

Generation of 'artificial' bursts in a turbulent boundary layer

In an effort to better understand the physics and structure of coherent events in a turbulent boundary layer, an attempt is made to produce 'artificial' bursts. These are generated in a unique turbulent boundary layer, developed on a flat plate towed in an 18-m water channel, and thus with negligible freestream turbulence. The burst-like events are produced by either withdrawing near-water fluid from two minute holes separated in the spanwise direction, or by pitching a miniature delta wing that is flush-mounted to the wall. Either of these two actions generates a hairpin-like vortex and low-speed streak that resemble naturally occurring structures. The resulting sequence of events that occur at a given location can be controlled at will, thus allowing detailed examination via phase-locked measurements and flow visualization. In this paper, the artificial bursts are compared with natural, random bursts, using flow visualization and hot-film signals. Detailed quantitative data on topographical details and dynamical significance of the bursting structure will be addressed in a forthcoming article.

Gad-El-hak, M.↗

A review and analysis of boundary layer transition data for turbine application

A symposium on transition in turbines was held at the NASA Lewis Research Center. One recommendation of the working groups was the collection of existing transition data to provide standard cases against which models could be tested. A number of data sets from the open literature that include heat transfer data in apparently transitional boundary layers, with particular application to the turbine environment, were reviewed and analyzed to extract transition information from the heat transfer data. The data sets reviewed cover a wide range of flow conditions, from low speed, flat plate tests to full scale turbine airfoils operating at simulated turbine engine conditions. The results indicate that free stream turbulence and pressure gradient have strong, and opposite, effects on the location of the start of transition and on the length of the transition zone.

Gaugler, R. E.↗