Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stack Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Cross-Cutting Metrology Tools for In Operando Characterization of Carrier Dynamics in Photovoltaic Devices (Final Technical Report)

Understanding the nature of recombination and its dependence on defects and interfaces is essential for engineering materials and contacts for higher V oc and photovoltaic (PV) efficiency. Time-resolved photoluminescence (TRPL) has conventionally been used to evaluate recombination, but not all materials are strongly emissive or otherwise suitable. Time-resolved terahertz spectroscopy is a pump – probe method that presents valuable complementary information, wherein an optical pump pulse photoexcites carriers within the absorber and the transient photoconductivity is probed with a terahertz pulse. Until now, experimental constraints have prohibited the use of terahertz probes to interrogate full device stacks, and measurements were instead made on exfoliated films or films grown on unconventional substrates. However, interfaces are critical to the behavior of photoexcited carriers in solar cells, and the substrates themselves often influence the film growth and bulk properties. Therefore, it is important to probe the behavior of PV absorbers as close as possible to their normal operating conditions. Here we have developed cross-cutting metrology that enable in operando characterization of carrier dynamics and recombination mechanisms in working PV devices. Through a combination of complementary non-contact TRTS and TRPL experiments and modeling, we have obtained key parameters including photoexcited carrier bulk lifetime and interface and back surface recombination velocities with greater precision and accuracy than can be achieved with conventional TRPL alone. By varying pulsed photoexcitation conditions, the contributions of interface and bulk recombination mechanisms can be determined. We have developed and refined this characterization approach by investigating CdTe PVs, which is a well-established technology but with significant margin for further improvements in efficiency. Results were published in Journal of Applied Physics (DOI: 10.1063/5.0064730) and Proceedings of the IEEE PVSC (DOI: 10.1109/PVSC43889.2021.9518559). After validating the approach, we have applied it to correlate recombination rates to processing conditions and material properties, including composition and defects as well as interfaces and surface treatments. Such feedback can inform processing and design choices to enable higher PV efficiency, not only for CdTe, but also CdSe x Te 1-x , CIGS, perovskites, kesterites, and future technologies. A perspective on predicting solar cell performance from terahertz spectroscopy was published in Advanced Energy Materials (DOI: 10.1002/aenm.202102776). The cross-cutting metrology tools developed here will enable determination of the locus and mechanism of performance-limiting recombination in thin film PV devices. This feedback can guide the engineering of PV devices with higher V oc and efficiency, thereby leading to reductions in levelized cost of electricity to meet the SunShot 2030 target of $0.03/kWh for utility-scale PV. Lower costs will enable rapid expansion of renewable electricity generation that is nearly free of carbon emissions. Reducing carbon emissions of the electricity sector is one of the most important solutions to climate change. The project’s specific focus on CdTe PV can benefit First Solar, the US company that is the global leader in CdTe technology, through both technology and workforce development.

14 SOLAR ENERGY↗

Emergent Above-Gap Photoluminescence in Molecularly Engineered Hybrid Bilayer Crystals

Bilayer crystals, built by stacking two-dimensional (2D) covalent monolayers, give rise to coupled excitonic states whose properties are constrained by fixed lattice symmetry and orientation. Replacing one covalent monolayer with a 2D molecular crystal––held together by non-covalent forces––overcomes this limitation, as molecular functional groups afford tunable in-plane lattice geometry, intermolecular spacing, and interlayer coupling, providing a powerful knob for exciton engineering. Here, in this study, we report four-atom-thick hybrid bilayer crystals (HBCs) synthesized by directly growing single-crystalline PDI molecular crystal atop WS 2 monolayers, which exhibit a robust photoluminescence (PL) peak 120 meV above the WS 2 optical band gap alongside a belowgap emission. Both peaks display strong polarization anisotropy—nearing unity for the above-gap emission—and maintain a perfectly linear power-law dependence up to an excitation density of ~10 7 mW/cm 2 , indicative of coexisting localized and delocalized excitonic states. Substituting PDI with a PTCDA monolayer on WS 2 fully quenches PL, demonstrating molecular control over excitonic emission. Lattice scale ab initio GW and GW-BSE calculations reveal a significantly hybridized bilayer band structure in PDI/WS 2 that supports interlayer excitonic species both above and below the WS 2 gap with strong polarization anisotropy, in excellent agreement with experiment. Our work introduces a molecule-based bilayer platform for the bottom-up design and control of excitonic phenomena in atomically thin optoelectronic and quantum materials.

2D materials↗

Active Radiative Thermal Switching with Graphene Plasmon Resonators

We theoretically demonstrate a near-field radiative thermal switch based on thermally excited surface plasmons in graphene resonators. The high tunability of graphene enables substantial modulation of near-field radiative heat transfer, which, when combined with the use of resonant structures, overcomes the intrinsically broadband nature of thermal radiation. In canonical geometries, we use nonlinear optimization to show that stacked graphene sheets offer improved heat conductance contrast between “ON” and “OFF” switching states and that a >10× higher modulation is achieved between isolated graphene resonators than for parallel graphene sheets. In all cases, we find that carrier mobility is a crucial parameter for the performance of a radiative thermal switch. Furthermore, we derive shape-agnostic analytical approximations for the resonant heat transfer that provide general scaling laws and allow for direct comparison between different resonator geometries dominated by a single mode. The presented scheme is relevant for active thermal management and energy harvesting as well as probing excited-state dynamics at the nanoscale.

30 DIRECT ENERGY CONVERSION↗

Laser powder bed fusion of oxide dispersion-strengthened IN718 alloys: A complementary study on microstructure and mechanical properties

In this study, two new grades of oxide dispersion strengthened (ODS) Inconel 718 (IN718) alloys were designed by the thermochemical CALPHAD method and produced by laser powder bed fusion (LPBF) technique. Alloys designated as IN718-YF and IN718-YFH, that consist Y 2 O 3 –FeO and Y 2 O 3 –FeO–Hf, respectively, were fabricated with >99.9 % densification using optimized process parameters. CALPHAD calculations were highly consistent with experimental findings, highlighting the formation of Al-containing Y–Ti–O and Y–Hf–O nano-oxides in both alloy types. Texture analyzes revealed no significant texture development in as-built (AB) or heat-treated (HT) alloys. Heat treatment was applied at 1050 °C for 1 h to enhance nano-oxide density. Further, the nano-oxide number density remained similar in IN718-YF while it decreased in IN718-YFH alloy as a result of carbide formation after the heat treatment. Besides, formation of secondary γ' particles was observed in the IN718-YFH/HT alloy. Even though the yield strengths of IN718-YF and IN718-YFH alloys in both AB and HT conditions were similar, the ductility of IN718-YFH was ~50 % less in almost all conditions compared to the ductility of IN718-YF. This has been shown to be as a result of irregular shaped micron-sized Y-Hf-O oxides, martensite formation in AB condition, increased amount of carbides and existence of secondary γ' particles in HT condition in IN718-YFH. High density of stacking faults (SF) forming at the interface of the nano-oxides have been detected in IN718-YF alloys. Besides dislocation/nanoparticle interactions, SFs which are responsible for the delocalization of the deformation improve the ductility of IN718-YF alloys. Overall, high temperature mechanical tests exhibit that both alloys have higher strength with improved ductility compared to the standard IN718 alloys, indicating the contribution of the nano-oxides.

36 MATERIALS SCIENCE↗

WETO Software Stack Best Practices

Wind energy researchers typically share one key characteristic: a passion for increasing wind energy in the global energy mix. The U.S. Department of Energy (DOE) supports this mission in a number of ways including allocating funding directly to various aspects of wind energy research through the Office of Energy Efficiency and Renewable Energy (EERE) via the Wind Energy Technologies Office (WETO). While the traditional output of research is academic publication, software development efforts are increasingly a major focus. Software tools in the research environment allow researchers to describe an idea and quickly increase the scope and scale as they study it further. As a product of research, these tools represent a direct pipeline from researcher to industry practitioners since they are the implementation of ideas described in academic publications. Given this vital role in wind energy research and commercial development, the broad research software portfolio supported by WETO must maintain a minimum level of quality to support the wind energy field in the growing transition to renewable energy. This report outlines a series o f best practices to be adopted by all WETO-supported software projects, as well as expectations that the communities interacting with these projects should have of the developers and tools themselves. Wind energy research software has a unique standing in the field of scientific software. The stakeholders are varied with a subset being: (1) DOE EERE leadership, (2) DOE WETO leadership and program managers, (3) National lab leadership, (4) Associated project principle investigators, (5) Research software engineers, (6) Wind energy researchers in academia (including graduate students, post docs, and national lab staff), (7) Industry researchers and practitioners, (8) Commercial software developers, and (9) The general public interested in wind energy. These software are typically the end-user of other generic software libraries, so the funding cycles are often tied to applied research rather than the development of the software itself. Since the developers are also wind energy researchers, these tools are typically designed in a way that closely resembles the application in which they're used. Additionally, the expertise and incentives for the developers have a high variability, and often neither are aligned with software engineering or computer science. Given the unique environment in which wind energy research software is produced and consumed, it is critical for model owners to understand the context of their software. A framework for developing this understanding is to answer the following questions of a given software project: What is it's purpose? What is its role in the field of wind energy? What is the profile of the expected users? For how long will it be relevant? What is the expected impact? These questions allow model owners to identify the appropriate methods for the design, development, and long term maintenance of their software. Additionally, the answer provide context for future planners to understand why particular decisions were made and discern the consequences of changing course. The information is aggregated from experience within WETO-supported software development groups as well as external organizations and efforts to define the craft of research software engineering. These best practices aim to make the collaborative development process efficient and effective while improving the model understanding across stakeholders. Additionally, the general adoption of a common framework for software quality ensures that the end users of WETO software can trust these tools and accurately understand the risks to workflow integration.

17 WIND ENERGY↗

Giant anisotropic in-plane thermal conduction induced by Anomalous phonons in pentagonal PdSe 2

In two-dimensional materials, different atomic stacking induces anisotropic atomic interactions and phonon dispersions, leading to the anisotropy of in-plane thermal transport. In this work, we report an exceptional case in layered pentagonal PdSe 2 , where the bonding, force constants, and lattice constants are nearly-equal along the in-plane crystallographic axis directions, while the thermal conductivity is surprisingly much greater along b-axis than along a-axis with a ratio up to 1.8. Such strong anisotropy is not only unexpected in in-plane uniform structured materials, but also 2 comparable to the record high in-plane anisotropic thermal conductivity in the nonuniform structured material reported to date (the ratio is ~2.0 in TiS 3 ). By combining the inelastic X-ray scattering measurement and the first-principles calculations, we attribute such high anisotropy to the low-energy phonons along a-axis, particularly their lower group velocities and “avoided-crossing” behavior. The different buckling structures between a- (zigzag-type) and b-axis (flat-type) are mainly responsible for such unique phonon dynamics properties of PdSe 2 . This finding helps to discover materials with high anisotropic in-plane thermal conductivity in uniform structures and reveals new physics of anisotropy of in-plane thermal conduction. Due to the unique features in structure and thermal transport properties, PdSe 2 may serve as a new platform for designing novel devices to route heat flow precisely at the nanoscale.

36 MATERIALS SCIENCE↗

Enhanced Light Outcoupling from OLEDs Fabricated on Novel Low-Cost Patterned Plastic Substrates of Varying Periodicity

OLEDs continue to make strides in display applications, but their commercial utilization in solid-state lighting (SSL) is lagging. An ongoing challenge, in particular for manufacturing, is the need for enhanced efficiency and hence the necessity to increase in an inexpensive approach the extraction of the light generated inside the OLED into the forward (viewing) hemisphere. In conventional OLEDs fabricated on a transparent flat anode coated on glass, the external quantum efficiency (EQE) is only ~20%. About 50% of the light is lost to internal waveguiding in the high refractive index (RI) organic + ITO anode layers and to surface plasmon polaritons (SPPs) at the organic/metal cathode interface. Another ~30% of the light is externally waveguided in the substrate to its edges. While extraction of the externally waveguided light is commonly addressed by adding a microlens array (MLA) or a scattering layer at the substrate’s air-side, light outcoupling increases by only ~1.6-1.7x (vs up to 2.5x in improving from ~20% to ~50%). The use of a hemispherical lens or an index matching fluid (IMF) at the substrate/photodetector (PD) interface increases the outcoupling by at least 2x; these approaches however, are not viable industrially, and even a MLA is sometimes undesirable due to its non-planar, scattering structure. In multi-stack tandem OLEDs, where the metal cathode is far from the emitting zone(s), the impact of photons loss to SPPs decreases. Our project addressed the ~50% loss to the internally waveguided light and SPPs. We evaluated OLEDs fabricated on patterned or planarized plastic substrates manufactured in a cost-effective approach compatible with a roll-to-roll (R2R) process. The OLEDs were either (i) patterned to various degrees depending on the pitch a and height or depth h of the pattern features or (ii) planar, with a pattern buried under a flat high RI planarization layer. We demonstrated that the outcoupling from green patterned OLEDs reaches ~50% by mitigating plasmon–related loss and internal waveguiding, even without the addition of a MLA, a hemispherical lens, or IMF. Simulations conducted in parallel with the experimental effort demonstrated how diffraction by conformally corrugated OLEDs increases the outcoupling to >60%. Structures with varying pitch values were also simulated indicating that combining domains of varying pitch could increase outcoupling to 55-60%. Experimentally, we additionally assessed the role a and h in determining not only the OLED efficiencies, but also their structural properties, i.e., the uniformity and conformality throughout the OLED stack. As planar OLEDs are preferred over corrugated devices, we studied different patterns in plastic substrates that were planarized by a high RI formulation. Planar green OLEDs on such structures showed enhanced efficiencies with EQEs larger than 60% with the addition of an IMF (to extract the substrate mode) at the substrate/Si PD interface. White OLEDs showed EQEs of 45.5%. Plastic substrates are currently less attractive than glass substrates due to drawbacks such as permeability to water vapor and oxygen, and in some cases thermal instability. Plastic substrates however, are flexible and easy to handle unlike thin flexible glass, and once transparent thin barrier films are available, they will become more attractive; they are already of interest in medical applications. Importantly, as it is easy to generate various patterns in different plastic materials, they provide excellent means for assessing and optimizing enhancing extracting structures. Such structures can also be transferred to glass substrates with some process modifications. The technical effectiveness and economic feasibility of the project lie in the patterning of the extracting plastic substrates in an approach that is scalable to R2R manufacturing. R2R processes are of drastically lower-cost than batch or single-unit fabrication. The patterned plastic can be a part of an integrated substrate either plastic or glass, which includes also a MLA or a planar layer with embedded scattering particles, as well as a conductive metal mesh/electrode design. SSL is environmentally-friendly and as OLED SSL becomes more efficient it will reduce electricity consumption, and hence lighting cost, as well as produce less expensive attractive lighting fixtures. Our university-industry collaboration is hence of major benefit to the public as it demonstrates the feasibility of manufacturing optimized extracting substrates for highly efficient OLEDs for SSL in a future R2R process, which would drastically reduce the manufacturing cost and increase production in the USA. Moreover, newly developed methods by our team allow low-cost roll manufactured substrates to be transferred to flexible or rigid glass substrates, which solves the plastic substrate barrier issues, and when combined with device encapsulation will increase the OLEDs’ environmental stability.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Fate of Mercury in Synthetic Gypsum Used for Wallboard Production

This report presents and discusses results from the project 'Fate of Mercury in Synthetic Gypsum Used for Wallboard Production', performed at five different full-scale commercial wallboard plants. Synthetic gypsum produced by wet flue gas desulfurization (FGD) systems on coal-fired power plants is commonly used in the manufacture of wallboard. This practice has long benefited the environment by recycling the FGD gypsum byproduct, which is becoming available in increasing quantities, decreasing the need to landfill this material, and increasing the sustainable design of the wallboard product. However, new concerns have arisen as recent mercury control strategies involve the capture of mercury in FGD systems. The objective of this study has been to determine whether any mercury is released into the atmosphere at wallboard manufacturing plants when the synthetic gypsum material is used as a feedstock for wallboard production. The project has been co-funded by the U.S. DOE National Energy Technology Laboratory (Cooperative Agreement DE-FC26-04NT42080), USG Corporation, and EPRI. USG Corporation is the prime contractor, and URS Group is a subcontractor. The project scope included seven discrete tasks, each including a test conducted at various USG wallboard plants using synthetic gypsum from different wet FGD systems. The project was originally composed of five tasks, which were to include (1) a base-case test, then variations representing differing power plant: (2) emissions control configurations, (3) treatment of fine gypsum particles, (4) coal types, and (5) FGD reagent types. However, Task 5,could not be conducted as planned and instead was conducted at conditions similar to Task 3. Subsequently an opportunity arose to test gypsum produced from the Task 5 FGD system, but with an additive expected to impact the stability of mercury, so Task 6 was added to the project. Finally, Task 7 was added to evaluate synthetic gypsum produced at a power plant from an additional coal type. In the project, process stacks in the wallboard plant were sampled using the Ontario Hydro method. In every task, the stack locations sampled included a gypsum dryer and a gypsum calciner. In Tasks 1 and 4 through 7, the stack of the dryer for the wet wallboard product was also tested. Also at each site, in-stream process samples were collected and analyzed for mercury concentration before and after each significant step in wallboard production. These results and process data were used to construct mercury mass balances across the wallboard plants. The results from the project showed a wide range of percentage mercury losses from the synthetic gypsum feedstocks as measured by the Ontario Hydro method at the process stacks, ranging from 2% to 55% of the mercury in the gypsum feedstock. For the tasks exceeding 10% mercury loss across the wallboard plant, most of the loss occurred across the gypsum calciner. When total wallboard emissions remained below 10%, the primary emission location varied with a much less pronounced difference in emission between the gypsum dryer, calciner and board dryer. For all seven tasks, the majority of the mercury emissions were measured to be in the elemental form (Hg{sup 0}). Overall, the measured mercury loss mass rates ranged from 0.01 to 0.17 grams of mercury per dry ton of synthetic gypsum processed, or 0.01 to 0.4 pounds of mercury released per million square feet of wallboard produced from synthetic gypsum. The Coal Combustion Product Production and Use Survey from the American Coal Ash Association (ACAA) indicate that 7,579,187 short tons of synthetic gypsum were used for wallboard production in 2006. Extrapolating the results of this study to the ACAA industry usage rate, we estimate that mercury releases from wallboard production plants in 2006 ranged between 150 to 3000 pounds for the entire U.S. wallboard industry. With only seven sets of wallboard plant measurements, it is difficult to draw firm conclusions about what variables impact the mercury loss percentages across the wallboard plants. One significant observation from this study was that higher purge rates of chlorides and fine solid particles from the wet FGD systems appear to produce gypsum with lower mercury concentrations. Any chemical interaction between mercury and chlorides is not well understood; however, based on the information available the lower mercury content in the gypsum product is likely due to the blow down of fine, mercury-rich particles as opposed to a decreased chloride concentration. One possible explanation is that a decrease of fine particles in the FGD slurry allows for less adsorption of mercury onto those particles, thus the mercury remains with the FGD liquor rather than the gypsum product. A more detailed discussion on synthetic gypsum sources and FGD chemistry data can be found in the Experimental section of this report and Table 4.

01 COAL, LIGNITE, AND PEAT↗

Barium uranyl diphosphonates

Three Ba{sup 2+}/UO{sub 2}{sup 2+} methylenediphosphonates have been prepared from mild hydrothermal treatment of uranium trioxide, methylendiphosphonic acid (C1P2) with barium hydroxide octahydrate, barium iodate monohydrate, and small aliquots of HF at 200 Degree-Sign C. These compounds, Ba[UO{sub 2}[CH{sub 2}(PO{sub 3}){sub 2}]{center_dot}1.4H{sub 2}O (Ba-1), Ba{sub 3}[(UO{sub 2}){sub 4}(CH{sub 2}(PO{sub 3}){sub 2}){sub 2}F{sub 6}]{center_dot}6H{sub 2}O (Ba-2), and Ba{sub 2}[(UO{sub 2}){sub 2}(CH{sub 2}(PO{sub 3}){sub 2})F{sub 4}]{center_dot}5.75H{sub 2}O (Ba-3) all adopt layered structures based upon linear uranyl groups and disphosphonate molecules. Ba-2 and Ba-3 are similar in that they both have UO{sub 5}F{sub 2} pentagonal bipyramids that are bridged and chelated by the diphosphonate moiety into a two-dimensional zigzag anionic sheet (Ba-2) and a one-dimensional ribbon anionic chain (Ba-3). Ba-1, has a single crystallographically unique uranium metal center where the C1P2 ligand solely bridges to form [UO{sub 2}[CH{sub 2}(PO{sub 3}){sub 2}]{sup 2-} sheets. The interlayer space of the structures is occupied by Ba{sup 2+}, which, along with the fluoride ion, mediates the structure formed and maintains overall charge balance. - Graphical abstract: Illustration of the stacking of the layers in Ba{sub 3}[(UO{sub 2}){sub 4}(CH{sub 2}(PO{sub 3}){sub 2}){sub 2})F{sub 6}]{center_dot}6H{sub 2}O viewed along the c-axis. The structure is constructed from UO{sub 7} pentagonal bipyramidal units, U(1)O{sub 7}=gray, U(2)O{sub 7}=yellow, barium=blue, phosphorus=magenta, fluorine=green, oxygen=red, carbon=black, and hydrogen=light peach. Highlights: Black-Right-Pointing-Pointer The polymerization of the UO{sub 2}{sup 2+} sites to form uranyl dimers leads to structural variations in compounds. Black-Right-Pointing-Pointer Barium cations stitch uranyl diphosphonate anionic layers together, and help mediate structure formation. Black-Right-Pointing-Pointer HF acts as both a mineralizing agent and a ligand.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Uranium diphosphonates templated by interlayer organic amines

The hydrothermal treatment of uranium trioxide and methylenediphosphonic acid with a variety of amines (2,2-dipyridyl, triethylenediamine, ethylenediamine, and 1,10-phenanthroline) at 200 Degree-Sign C results in the crystallization of a series of layered uranium diphosphonate compounds, [C{sub 10}H{sub 9}N{sub 2}]{l_brace}UO{sub 2}(H{sub 2}O)[CH{sub 2}(PO{sub 3})(PO{sub 3}H)]{r_brace} (Ubip2), [C{sub 6}H{sub 14}N{sub 2}]{l_brace}(UO{sub 2}){sub 2}[CH{sub 2}(PO{sub 3})(PO{sub 3}H)]{sub 2}{center_dot}2H{sub 2}O{r_brace} (UDAB), [C{sub 2}H{sub 10}N{sub 2}]{sub 2}{l_brace}(UO{sub 2}){sub 2}(H{sub 2}O){sub 2}[CH{sub 2}(PO{sub 3}){sub 2}]{sub 2}{center_dot}0.5H{sub 2}O{r_brace} (Uethyl), and [C{sub 12}H{sub 9}N{sub 2}]{l_brace}UO{sub 2}(H{sub 2}O)[CH{sub 2}(PO{sub 3})(PO{sub 3}H)]{r_brace} (Uphen). The crystal structures of the compounds are based on UO{sub 7} units linked by methylenediphosphonate molecules to form two-dimensional anionic sheets in Ubip2 and UDAB, and one-dimensional anionic chains in Uethyl and Uphen, which are charge balanced by protonated amine molecules. Interaction of the amine molecules with phosphonate oxygens and water molecules results in extensive hydrogen bonding in the interlayer. These amine molecules serve both as structure-directing agents and charge-balancing cations for the anionic uranium phosphonate sheets and chains in the formation of the different coordination geometries and topologies of each structure. Reported herein are the syntheses, structural and spectroscopic characterization of the synthesized compounds. - Graphical abstract: The Raman spectra of the synthesized compounds and an illustration of the stacking of the layers with the diprotonated triethylenediamine molecules in [C{sub 6}H{sub 14}N{sub 2}]{l_brace}(UO{sub 2}){sub 2}[CH{sub 2}(PO{sub 3})(PO{sub 3}H)]{sub 2}{center_dot}2H{sub 2}O{r_brace} UDAB. Solvent water molecules are removed for clarity. The corresponding Raman spectra for the complexes synthesized is also shown. The structure is constructed from UO{sub 7} pentagonal bipyramids (yellow), oxygen=red, phosphorus=magenta, carbon=black, and nitrogen=blue. Highlights: Black-Right-Pointing-Pointer Organic amines act both as charge-balancing and as structure-directing agents. Black-Right-Pointing-Pointer Extensive hydrogen bonding interactions with solvent water molecules and amines. Black-Right-Pointing-Pointer Altering the organic amine (size or flexibility) affects structure formation.

36 MATERIALS SCIENCE↗

Assembly of Arbitrary Designer Heterostructures with Atomically Clean Interfaces

Van der Waals heterostructures are an excellent platform for studying intriguing interface phenomena, such as moiré and proximity effects. Many of these phenomena occurring in such heterostructures' interfaces and surfaces have so far been hampered because of their high sensitivity to disorder and interface contamination. Here, it reports a dry polymer-based assembly technique to fabricate arbitrary designer van der Waals heterostructures with atomically clean surfaces. The key features of the suspended dry pick-up and flip-over assembly technique are: 1) the heterostructure surface never comes into contact with polymers, 2) the assemble is entirely solvent-free, 3) it is entirely performed in a glovebox, and 4) it only requires temperatures below 130 °C. By performing ambient atomic force microscopy and atomically-resolved scanning tunneling microscopy on example heterostructures, it demonstrates the fabrication of air-sensitive heterostructures with ultra-clean interfaces and surfaces. It envisions that, due to the avoidance of polymer melting, this technique is potentially compatible with heterostructure assembly under ultra-high vacuum conditions, which promises ultimate heterostructure quality.

2D materials↗

Advanced Mud System for Microhole Coiled Tubing Drilling

An advanced mud system was designed and key components were built that augment a coiled tubing drilling (CTD) rig that is designed specifically to drill microholes (less than 4-inch diameter) with advanced drilling techniques. The mud system was tailored to the hydraulics of the hole geometries and rig characteristics required for microholes and is capable of mixing and circulating mud and removing solids while being self contained and having zero discharge capability. Key components of this system are two modified triplex mud pumps (High Pressure Slurry Pumps) for advanced Abrasive Slurry Jetting (ASJ) and a modified Gas-Liquid-Solid (GLS) Separator for well control, flow return and initial processing. The system developed also includes an additional component of an advanced version of ASJ which allows cutting through most all materials encountered in oil and gas wells including steel, cement, and all rock types. It includes new fluids and new ASJ nozzles. The jetting mechanism does not require rotation of the bottom hole assembly or drill string, which is essential for use with Coiled Tubing (CT). It also has low reactive forces acting on the CT and generates cuttings small enough to be easily cleaned from the well bore, which is important in horizontal drilling. These cutting and mud processing components and capabilities compliment the concepts put forth by DOE for microhole coiled tubing drilling (MHTCTD) and should help insure the reality of drilling small diameter holes quickly and inexpensively with a minimal environmental footprint and that is efficient, compact and portable. Other components (site liners, sump and transfer pumps, stacked shakers, filter membranes, etc.. ) of the overall mud system were identified as readily available in industry and will not be purchased until we are ready to drill a specific well.

03 NATURAL GAS↗

Crashworthiness Models for Automotive Batteries

Safety is a key element of any device designed to store energy, particularly of electrochemical batteries, which convert energy of chemical reactions to electrical energy. Safety considerations are especially important when applied to large automotive batteries designed for propulsion of electric vehicles (EV). The high amount of energy stored in EV battery packs translates to higher probability of fire in case of severe deformation of battery compartment due to automotive crash or impact caused by road debris. While such demand for safety has resulted in heavier protection of battery enclosure, the mechanisms leading to internal short circuit due to deformation of the battery are not well understood even on the level of a single electrochemical cell. Moreover, not all internal shorts result in thermal runaway, and thus a criterion for catastrophic failure needs to be developed. This report summarizes the effort to pinpoint the critical deformation necessary to trigger a short via experimental study on large format automotive Li-ion cells subjected to large deformations as those occurring in deformation of battery module or pack. Mechanical properties of cell components were determined via experimental testing and served as input for constitutive models of Finite Element (FE) analysis. It has been rationalized that long-range stress fields occurring in spherical indentation of battery modules would trigger different deformation and failure scenarios compared to indentation of a single cell supported by a rigid flat surface. In order to investigate large deformations characteristic of battery module, a custom experimental set up has been built where the pouch cell was deformed against a compliant backing, which was represented by a ballistic clay. Experiments were also conducted on deformation of stacks of 10 pouch cells, - configuration representing half-module in Ford Focus EV battery pack without cooling plates and structural components. Comparison of the results shows promise for the compliant backing setup for safety evaluation of battery cells under more realistic conditions compared to indentation of single cell against undeformable backing where compression and electrode particle penetration through separator could be the major mechanism for short circuit.

25 ENERGY STORAGE↗

Charge Transport across DNA-Based Three-Way Junctions

DNA-based molecular electronics will require charges to be transported from one site within a 2D or 3D architecture to another. While this has been shown previously in linear, π-stacked DNA sequences, the dynamics and efficiency of charge transport across DNA three-way junction (3WJ) have yet to be determined. Here, we present an investigation of hole transport and trapping across a DNA-based three-way junction systems by a combination of femtosecond transient absorption spectroscopy and molecular dynamics simulations. Hole transport across the junction is proposed to be gated by conformational fluctuations in the ground state which bring the transiently populated hole carrier nucleobases into better aligned geometries on the nanosecond time scale, thus modulating the π–π electronic coupling along the base pair sequence.

59 BASIC BIOLOGICAL SCIENCES↗

Morphological Evolution of Multilayer Ni/NiO Thin Film Electrodes during Lithiation

Oxide conversion reactions in lithium ion batteries are challenged by substantial irreversibility associated with significant volume change during the phase separation of an oxide into lithia and metal species (e.g., NiO + 2Li + + 2e – → Ni + Li 2 O). In this work, we demonstrate that the confinement of nanometer-scale NiO layers within a Ni/NiO multilayer electrode can direct lithium transport and reactivity, leading to coherent expansion of the multilayer. The morphological changes accompanying lithiation were tracked in real-time by in-operando X-ray reflectivity (XRR) and ex-situ cross-sectional transmission electron microscopy on well-defined periodic Ni/NiO multilayers grown by pulsed-laser deposition. Comparison of pristine and lithiated structures reveals that the nm-thick nickel layers help initiate the conversion process at the interface and then provide an architecture that confines the lithiation to the individual oxide layers. XRR data reveal that the lithiation process starts at the top and progressed through the electrode stack, layer by layer resulting in a purely vertical expansion. Longer term cycling showed significant reversible capacity (~800 mA h g –1 after ~100 cycles), which we attribute to a combination of the intrinsic bulk lithiation capacity of the NiO and additional interfacial lithiation capacity. These observations provide new insight into the role of metal/metal oxide interfaces in controlling lithium ion conversion reactions by defining the relationships between morphological changes and film architecture during reaction.

36 MATERIALS SCIENCE↗

Self-assembly of membrane-like materials from highly stable protein-mimetics

Protein self-assembly is a commonplace phenomenon in living systems and is frequently responsible for building molecular machines that carry out the vast array of functions, such as molecular separation and selective ion transport. Inspired by in nature, various proteins and peptides have been designed and exploited for self-assembly of functional materials in vitro. However, the application of these protein- and peptide-based materials is limited because of their poor stabilities against thermal and chemical degradation. Therefore, there is a great need to develop protein-like synthetic polymers that can function like proteins and peptides for molecular recognition and self-assembly, but exhibit high stabilities. There are several known chemical systems that can create non-natural, sequence-specific polymers, such as ?-peptides and peptoids (poly-N-substituted glycines). Peptoids have received particular attention because they can be cheaply and efficiently synthesized, and several hundred commercially available amines can be used to build their large side-chain diversity. We recently demonstrated that peptoids were able to mimic peptides commonly present in natural biominerals for unprecedented control over both calcite morphology and growth kinetics. In this presentation, we report our progress in exploiting peptoids to mimic proteins and peptides for self-assembly. Specifically, we demonstrate that 12-mer peptoids are able to self-assemble into highly-ordered membrane-like materials both in solution and on substrate surfaces. In aqueous solution, these peptoids self-assemble into highly-crystalline and free-floating nanosheets through a solvent-driven crystallization process. These nanosheets have single-bilayer thickness (3.2 nm) and large area (up to mm2). X-ray diffraction data indicate that these peptoids are highly packed through p-p stacking and peptoid side-chain hydrogen bonding. These results represent the smallest peptoid oligomers that self-assemble into free-floating nanosheets and do not require the compression of monolayers formed at the water-air interface. The formation of single-bilayer-thick nanosheets also occurs on various substrate surfaces. For example, on freshly-cleaved mica surface, we observed that nanosheets were formed through a heterogeneous nucleation process. Similar nanosheets were assembled even when 12-mer peptoids were specifically conjugated with functional groups, indicating that self-assembly of 12-mer peptoids into nanosheets is robust, and these nanosheets can serve as a well-defined 2D platform for post-functionalization. Peptoid self-assembly is highly sequence-specific, and pH sensitive. When the diblock-like 12-mer peptoids are switched to an alternative motif, the resulting 12-mers only self-assemble into fiber-like materials. Multi-scale simulations are also used to provide insights into peptoid-assembly mechanisms

Chen, Chunlong↗

Stacking-Sequence Changes and Na Ordering in Layered Intercalation Materials

The performance of Na-ion batteries is sensitive to the nature of cation ordering and phase transformations that occur within the intercalation compounds used as electrodes. In order to elucidate these effects in layered Na intercalation compounds, we have carried out a first-principles statistical mechanics study of Na ordering and stacking-sequence preferences in the model compound Na x TiS 2 . Our calculations predict a series of structural phase transitions at room temperature between O 3 , P 3 , O 1 , O 1 –O 3 staged hybrid, and O 1 –P 3 staged hybrid. We further explore the ordering of Na ions in P 3 and O 3 and find that these host structures favor very distinct Na-vacancy patterns. Low energy orderings on the honeycomb lattice in P 3 consist of triangular island domains with vacancies coalescing at antiphase boundaries. This results in a devil’s staircase of ground-state Na orderings within P 3 that are unlike the orderings possible in the triangular lattice of Na sites in O 3 . Here, we explore the role that antiphase boundaries play in mediating Na diffusion in the P 3 host.

25 ENERGY STORAGE↗