Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stack design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Pressure Dome for High-Pressure Electrolyzer

A high-strength, low-weight pressure vessel dome was designed specifically to house a high-pressure [2,000 psi (approx. = 13.8 MPa)] electrolyzer. In operation, the dome is filled with an inert gas pressurized to roughly 100 psi (approx. = 690 kPa) above the high, balanced pressure product oxygen and hydrogen gas streams. The inert gas acts to reduce the clamping load on electrolyzer stack tie bolts since the dome pressure acting axially inward helps offset the outward axial forces from the stack gas pressure. Likewise, radial and circumferential stresses on electrolyzer frames are minimized. Because the dome is operated at a higher pressure than the electrolyzer product gas, any external electrolyzer leak prevents oxygen or hydrogen from leaking into the dome. Instead the affected stack gas stream pressure rises detectably, thereby enabling a system shutdown. All electrical and fluid connections to the stack are made inside the pressure dome and require special plumbing and electrical dome interfaces for this to be accomplished. Further benefits of the dome are that it can act as a containment shield in the unlikely event of a catastrophic failure. Studies indicate that, for a given active area (and hence, cell ID), frame outside diameter must become ever larger to support stresses at higher operating pressures. This can lead to a large footprint and increased costs associated with thicker and/or larger diameter end-plates, tie-rods, and the frames themselves. One solution is to employ rings that fit snugly around the frame. This complicates stack assembly and is sometimes difficult to achieve in practice, as its success is strongly dependent on frame and ring tolerances, gas pressure, and operating temperature. A pressure dome permits an otherwise low-pressure stack to operate at higher pressures without growing the electrolyzer hardware. The pressure dome consists of two machined segments. An O-ring is placed in an O-ring groove in the flange of the bottom segment and is trapped by the flange on the top dome segment when these components are bolted together with high-strength bolts. The pressure dome has several unique features. It is made (to ASME Pressure Vessel guidelines) in a high-strength aluminum alloy with the strength of stainless steel and the weight benefits of aluminum. The flange of the upper dome portion contains specially machined flats for mounting the dome, and other flats dedicated to the special feedthroughs for electrical connections. A pressure dome can be increased in length to house larger stacks (more cells) of the same diameter with the simple addition of a cylindrical segment. To aid in dome assembly, two stainless steel rings are employed. One is used beneath the heads of the high-strength bolts in lieu of individual hardened washers, and another is used instead of individual nuts. Like electrolyzers could be operated at low or high pressures simply by operating the electrolyzer outside or inside a pressurized dome.

Norman, Timothy↗

Rapid Patterning and Advanced Device Structures for Low Cost Manufacturable Crystalline Si IBC Cells

Recent record efficiency Si cells have had an interdigitated back contact (IBC) design where both positive and negative contacts are fabricated on the back side of the Si wafer. Many industry groups have investigated IBC cells but used photolithography to pattern the rear contacts although it is considered impractical for low cost, high volume manufacturing. Alternative patterning methods using lasers and mechanical masking have been utilized in fabrication of patterned regions in IBC Si solar cells to replace photolithography. Another exciting advance in Si solar cell technology has been replacing the high temperature diffusion of doped regions inside the crystalline Si wafer with low temperature deposition of very thin layers of doped amorphous hydrogenated Si (a-Si:H) on the Si wafer. This is called a Si heterojunction (HJ) device. The a-Si:H provides excellent passivation of surface defects and has produced the highest open circuit voltages (VOC) of any Si solar cell device structure. The Institute of Energy Conversion (IEC) demonstrated the first IBC-HJ solar cell combining these two strategies in 2007 and has fabricated IBC-HJ cells with 20% efficiency using three photolithography steps. Despite the demonstrated efficiency potential of this device by industry groups (>26%) there is no commercial production because of the challenges of patterning and processing the structure in an industrial environment. Our work sought to address that challenge. The objective of this 3 year project was to develop the processing for the IBC-HJ Si solar cell using lasers for patterning and contact formation instead of photolithography. Laser patterning enables rapid, contactless manufacturing of patterned regions. We intensively studied laser fired contacts, laser patterning of the a-Si multi-layer stacks and metal layers and the use of plasma shadow masks. After an exhaustive focus in the first year on the laser fired emitter (LFE) and contact (LFC), we were unable to achieve VOC greater than 660 mV, compared to the 720 mV required to meet our milestones. We discovered that an additional issue with our original IBC structure was the presence of an inversion layer at the back surface connecting the p and n regions which reduced the VOC and fill factor (FF). We developed innovative methods for characterizing the inversion layer. These two limitations in the original design lead to development of a new IBC-HJ process sequence and device structure which we called Plasma Masked Laser Processed (PMLP). It retained the original high efficiency features including manufacturability. The LFC was replaced with a standard n-type a-Si HJ contact. The inversion layer was eliminated by replacing the previous p-type stack in the gap with an n-type or SiN stack. The PMLP used laser ablation of a multi-layer a-Si stack followed by chemical etching to open the n-contact. It required deposition of a patterned stack through a mask in the plasma deposition chamber. This turned out to be a source of significant problems due to inevitable unwanted deposition ‘leakage’ under the mask. This formed a blocking contact on the emitter which significantly reduced Voc and FF. Several iterations in PMLP device structure and chemical etching steps resulted in a large improvements, e.g. the efficiency increasing from 3 to 15% and Voc from 450 to 660 mV but they were unable to completely eliminate it. The best IBC-HJ device we fabricated had only 15% efficiency. For perspective, our standard FHJ devices had 20% efficiency.

14 SOLAR ENERGY↗

Flow simulation and analysis of high-power flow batteries

The cost of a flow battery system can be reduced by increasing its power density and thereby reducing its stack area. If per-pass utilizations are held constant, higher battery power densities can only be achieved using higher flow rates. Here, a 3D computational fluid dynamics model of a flow battery flow field and electrode is used to analyze the implications of increasing flow rates to high power density operating conditions. Interdigitated and serpentine designs, and cell sizes ranging from 10 cm 2 to 400 cm 2 , are simulated. The results quantify the dependence of pressure loss on cell size and design, demonstrating that the details of the passages that distribute flow between individual channels and the inlet and outlet have a major impact on pressure losses in larger cells. Additionally, in-cell flow behavior is analyzed as a function of cell size and design. Flow structures are interrogated to show how and where electrode parameters influence pressure drops, and how regions where transport is slow are correlated with the presence of experimentally observed cell degradation.

25 ENERGY STORAGE↗

Resistive switching and synaptic properties of fully atomic layer deposition grown TiN/HfO{sub 2}/TiN devices

Recently proposed novel neural network hardware designs imply the use of memristors as electronic synapses in 3D cross-bar architecture. Atomic layer deposition (ALD) is the most feasible technique to fabricate such arrays. In this work, we present the results of the detailed investigation of the gradual resistive switching (memristive) effect in nanometer thick fully ALD grown TiN/HfO{sub 2}/TiN stacks. The modelling of the I-V curves confirms interface limited trap-assisted-tunneling mechanism along the oxygen vacancies in HfO{sub 2} in all conduction states. The resistivity of the stack is found to critically depend upon the distance from the interface to the first trap in HfO{sub 2}. The memristive properties of ALD grown TiN/HfO{sub 2}/TiN devices are correlated with the demonstrated neuromorphic functionalities, such as long-term potentiation/depression and spike-timing dependent plasticity, thus indicating their potential as electronic synapses in neuromorphic hardware.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Experimental demonstration of voltage-matched two-terminal tandem minimodules

Mechanically stacked tandem solar cells are a potential near-term solution for increasing the efficiency of photovoltaic modules. Practical implementation requires an interconnection approach that maximizes efficiency and minimizes complexity and cost. Connecting the top and bottom cells in a voltage-matched configuration allows two-terminal modules to be fabricated without altering the cell design or processing methods. Here, we experimentally demonstrate two-terminal voltage-matched GaInP 2 / Si minimodules. The two-terminal minimodules performed just as well as four terminal configurations when voltage-matching requirements were met. The magnitude of the efficiency loss experienced by the voltage-matched minimodule when voltage-matched conditions were not met depends on whether the voltage was constrained by the GaInP 2 or Si cells. Monte Carlo simulations also indicate that the two-terminal voltage-matched tandems respond to small cell-to-cell parameter variations in a similar manner as four terminal tandems.

14 SOLAR ENERGY↗

Coherent Stacking Scheme for Inverse-Compton Scattering at MHz Repetition Rates

An experiment to produce 1-MeV gamma rays via Compton back-scattering of infrared photons on 250-MeV electron bunches is currently in preparation at the Fermilab Accelerator Science & Technology (FAST) facility. To increase the gamma-ray flux the energy of the infrared laser pulses are planned to be amplified within the interaction region using a resonant cavity. This passive amplifier composed of a Fabry-Perot cavity will allow the laser pulse bunches to coherently and constructively stack. Our estimates, based on theoretical models, show that the laser pulse energy can be increased from approximately 1-2 mJ at the exit of the last active amplifier to 5 -10 mJ at the interaction point when the laser repetition rate is set at the nominal value of 3 MHz. This paper details the cavity design option(s) and associated wave-optic simulations.

43 PARTICLE ACCELERATORS↗

Results of the 2018 Wood Stove Design Challenge

The 2018 Wood Stove Design Challenge was an international design competition which sought to identify top performing residential wood stoves based on automation. To prepare for the event, the Northeast States for Coordinated Air Use Management (NESCAUM) developed a testing protocol that challenged the stoves by testing them in more field-like conditions—capturing emissions from start-up, reloading a stove, and the use of larger piece sizes. Flue gas emissions were measured using a combination of in-stack and novel dilution sampling methods, as the event occurred on the National Mall in Washington D.C. in a non-laboratory setting. Particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO2), and methane (CH4) were measured from three stoves in real-time. A combustion efficiency was also calculated for each stove in real-time. Measured PM emission rates ranged between 1.8 and 8.0 g/hr for all stoves and operating conditions, with the highest emissions being measured during cold start in all cases. The test average PM emission rates were 2.4, 4.0, and 2.4 g/hr for stoves A, B, and C, respectively. Results showed emissions measured during transient operations, which are often excluded in current certification methods, can be significantly higher than steady-state periods—echoing other studies and highlighting the importance of testing in various operational modes for more realistic emission estimates. Additionally, the stoves had overall CO emission rates of 48.8, 284.8, and 100.8 g/hr, for stoves A, B and C, respectively. Calculated PM and CO emission factors overall were low considering the testing protocol sought to follow more challenging yet realistic practices in terms of fuel loading and operating procedures. The overall estimated combustion efficiency for stoves A, B, and C was 85%, 78%, 76%, respectively and in all cases was lowest during the cold start period.This report details the successfully proposed and assembled instrumentation that was relatively portable for field-site testing and the results of the emissions measurements for the 2018 Wood Stove Design Challenge competition. Overall, the repeatability of each stove was favorable with coefficients of variation (COV) ranging from 7 to 15% for measured PM concentrations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Hexagonal Geometries in MPACT

The MPACT code is a high-fidelity light-water reactor analysis code using whole-core pin-resolved neutron transport calculations on modern parallel-computing hardware. MPACT uses the 2D/1D method to solve 3D neutron transport problems by decomposing the problem into a stack of 2D slices, each of which is solved independently using the method of characteristics (MOC). The slices are then coupled axially using the P3 nodal expansion method (NEM-P3) for the 1D axial calculations. MPACT also employs the coarse mesh finite difference (CMFD) method to accelerate calculations. This manuscript details work supporting advanced reactor designs using hexagonal pins and hexagonal assemblies such as the VVER-1000. If performed correctly, MOC is geometry agnostic. However, MPACT previously had optimizations in place for Cartesian geometries, specifically in the modularization and current calculations. Sections 2 and 3 detail the changes made to MPACT to support MOC and CMFD calculations on hexagonal geometries. Section 4 reports results demonstrating solution consistency for problems run with and without CMFD acceleration, results demonstrating solution consistency when run in serial and parallel, and pincell results using the Monte Carlo code, McCard’s benchmark results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Scalable Membrane Electrode Assembly Stack Production for Reliable Thermal Electrochemical Converters (SMART)

This Final Close Out Report documents all activities, progress, and results accomplished under the SMART project, funded by the Department of Energy (DOE), during Budget Period 1 (BP1), covering 10/01/2023 to 07/31/2025. Although official preaward approval was granted on 05/10/2024, contracting delays shifted the award and formal project start to 10/01/2024. In the absence of an official kick-off meeting, early interactions focused on planning for key technical challenges, particularly the design and logistics for the JTEC device test platform.

30 DIRECT ENERGY CONVERSION↗

A Hands-On Curriculum for Training in HPC Cluster Deployment and Management

This paper presents the design, methodology, and outcomes of the High-Performance Computing Technologies (HPCT) course, a hands-on training program focused on the system-side of HPC cluster deployment and administration. Delivered as part of the Master in High Performance Computing (MHPC) program, the course introduces students to key concepts in cluster configuration, including networking, software stack provisioning, job scheduling, and monitoring. Initially taught in person, the course was transitioned to an online format during the COVID-19 pandemic. This shift led to the development of openly available instructional material and a flipped-classroom approach that continues to support both in-person and hybrid delivery. All course materials are publicly available at www.hpc.temple.edu/mhpc/hpc-technology/index.html. By documenting the structure, infrastructure, and evolution of HPCT, this paper offers a model for accessible HPC system training that supports workforce development in computational science.

Posada Correa, Fernando [ORNL] (ORCID:000000022565↗

An experimental investigation of the fracture behavior of thick, notched laminated composites

The fracture of high-modulus fiber-reinforced graphite/epoxy laminates with machined crack-like notches is discussed. An experimental program was conducted, in which stacking sequence,laminate thickness, notch size, and specimen configuration have been investigated. This research has led to the fundamental observation that heterogeneity significantly effects the fracture of thin laminates but has a relatively insignificant effect on the fracture of thick laminates. The results of this program are reviewed with the emphasis on the notch sensitivity and design of thick laminates.

Harris, Charles E.↗

Manufacturing and testing of a magnetically suspended composite flywheel energy storage system

This paper presents the work performed to develop a multiring composite material flywheel and improvements of a magnetically suspended energy storage system. The flywheel is constructed of filament would graphite/epoxy and is interference assembled for better stress distribution to obtain higher speeds. The stationary stack in the center of the disk supports the flywheel with two magnetic bearings and provides power transfer to the flywheel with a motor/generator. The system operates under a 10(exp -4) torr environment and has been demonstrated to 20,000 rpm with a total stored energy of 15.9 Wh. When this flywheel cycles between its design speeds (45,000 to 90,000 rpm), it will deliver 242 Wh and have a usable specific energy density of 42.6 Wh/kg.

Wells, Stephen↗

TEXCAD: TEXile Composite Analysis for Design

The Textile Composite Analysis for Design (TEXCAD) code provides the materials/design engineer with a user-friendly, desktop computer based tool for the analysis of a wide variety of fabric reinforced woven and braided composites. It can be used to calculate overall thermal and mechanical properties along with engineering estimates of damage progression and strength. TEXCAD also calculates laminate properties for stacked, oriented fabric constructions. It discretely models the yarn centerline paths within the textile repeating unit cell (RUC) by assuming sinusoidal undulations at yarn cross-over points and uses a year discretization scheme (which subdivides each yarn into smaller, piecewise straight yarn slices) together with a 3-D stress averaging procedure to compute overall stiffness properties. In the calculations for strength, it uses a curved beam-on-elastic foundation model for yarn undulating regions together with incremental approach in which stiffness properties for the failed yarn slices are reduced based on the predicted yarn slice failure mode. Nonlinear shear effects and nonlinear geometric effects can be stimulated. Input to TEXCAD consists of: (1) material parameters like impregnated yarn and resin properties such as moduli, Poisson's ratios, coefficients of thermal expansion, nonlinear shear parameters, axial failure strains, and in-plane failure stresses; and (2) fabric parameters like yarn sizes, braid angle, yarn packing density, filament diameter, and overall fiber volume fraction. Output consists of overall thermoelastic constants, yarn slice strains/stresses, yarn slice failure history, in-plane strain response, and ultimate failure strength. Strength can be computed under the combined action of thermal and mechanical loading (tension, compression, and shear). A brief overview of the analytical capabilities, program organization, and modules, input and output parameters, computer platforms, distribution, and modifications/extensions of the TEXCAD code are presented here.

Naik, Rajiv A.↗

Advanced Ceramic Matrix Composites with Multifunctional and Hybrid Structures

Ceramic matrix composites are leading candidate materials for a number of applications in aeronautics, space, energy, and nuclear industries. Potential composite applications differ in their requirements for thickness. For example, many space applications such as "nozzle ramps" or "heat exchangers" require very thin (< 1 mm) structures whereas turbine blades would require very thick parts (> or = 1 cm). Little is known about the effect of thickness on stress-strain behavior or the elevated temperature tensile properties controlled by oxidation diffusion. In this study, composites consisting of woven Hi-Nicalon (trademark) fibers a carbon interphase and CVI SiC matrix were fabricated with different numbers of plies and thicknesses. The effect of thickness on matrix crack formation, matrix crack growth and diffusion kinetics will be discussed. In another approach, hybrid fiber-lay up concepts have been utilized to "alloy" desirable properties of different fiber types for mechanical properties, thermal stress management, and oxidation resistance. Such an approach has potential for the C(sub I)-SiC and SiC(sub f)-SiC composite systems. CVI SiC matrix composites with different stacking sequences of woven C fiber (T300) layers and woven SiC fiber (Hi-Nicalon (trademark)) layers were fabricated. The results will be compared to standard C fiber reinforced CVI SiC matrix and Hi-Nicalon reinforced CVI SiC matrix composites. In addition, shear properties of these composites at different temperatures will also be presented. Other design and implementation issues will be discussed along with advantages and benefits of using these materials for various components in high temperature applications.

Singh, Mrityunjay↗

Marked Consequences of Systematic Oligothiophene Catenation in Thieno[3,4- c ]pyrrole-4,6-dione and Bithiopheneimide Photovoltaic Copolymers

As effective building blocks for high-mobility transistor polymers, oligothiophenes are receiving attention for polymer solar cells (PSCs) because the resulting polymers can effectively suppress charge recombination. In this work we investigate two series of in-chain donor–acceptor copolymers, PTPDnT and PBTInT, based on thieno[3,4-c]pyrrole-4,6-dione (TPD) or bithiopheneimide (BTI) as electron acceptor units, respectively, and oligothiophenes (nTs) as donor counits, for high-performance PSCs. Intramolecular S···O interaction leads to more planar TPD polymer backbones, however backbone torsion yields greater open-circuit voltages for BTI polymers. Thiophene addition progressively raises polymer HOMOs but marginally affects their band gaps. FT-Raman spectra indicate that PTPDnT and PBTInT conjugation lengths scale with nT catenation up to $n$ = 3 and then saturate for longer oligomer. Furthermore, the effects of oligothiophene alkylation position are explored, revealing that the alkylation pattern greatly affects film morphology and PSC performance. The 3T with “outward” alkylation in PTPD3T and PBTI3T affords optimal $π$-conjugation, close stacking, long-range order, and high hole mobilities (0.1 cm 2 /(V s)). These characteristics contribute to the exceptional ~80% fill factors for PTPD3T-based PSCs with PCE = 7.7%. The results demonstrate that 3T is the optimal donor unit among nTs ($n$ = 1–4) for photovoltaic polymers. Grazing incidence wide-angle X-ray scattering, transmission electron microscopy, and time-resolved microwave conductivity measurements reveal that the terthiophene-based PTPD3T blend maintains high crystallinity with appreciable local mobility and long charge carrier lifetime. These results provide fundamental materials structure-device performance correlations and suggest guidelines for designing oligothiophene-based polymers with optimal thiophene catenation and appropriate alkylation pattern to maximize PSC performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Truncating 2D Framework Materials Down to a Single Pore: Synthetic Approaches and Opportunities

Here, in this Accounts article, we summarize our recent work on truncating conjugated two-dimensional framework materials down to a single pore, or a single macrocycle. Conjugated 2D architectures have emerged as one of the most synthetically adaptable motifs for coupling semiconductivity and porosity in metal–organic frameworks (MOFs) and covalent organic frameworks (COFs). However, despite their prevalence, 2D architectures have several limitations. In particular, the strong interlayer π–π stacking can limit both processability and the accessibility of internal active sites. We have found that simple macrocycles preserve key aspects of 2D framework structure and function, including porosity and out-of-plane electrical conductivity, while providing improved processability, surface tunability, and mass transport properties. In this article, we first describe our synthetic approach and general design considerations. Specifically, we show how ditopic analogues of the tritopic ligands commonly found in the synthesis of 2D MOFs and COFs can be used to achieve a diverse library of conjugated macrocycles that resemble fragments of semiconducting frameworks in both form and function. The length of the peripheral side chains, the size of the aromatic core, and the solubility of intermediates are all key variables in favoring selective macrocycle formation over undesired linear polymers and oligomers. Next, we highlight the unique advantages that macrocycles provide, including improved processability, atomically precise surface tunability, and greater active site accessibility. In particular, the identity of the peripheral side chains dramatically impacts both solubility and colloidal stability as well as crystal size and morphology. We further show how the solution processability and nanoscale dimensions of macrocycles can simplify electronic device fabrication and improve electrochemical performance. Finally, we end with a forward-looking discussion on how macrocycles offer a unique bridge between conjugated molecules and extended frameworks, enabling new application areas and fundamental science.

charge transport↗